Properties of Zn3N2-doped ZnO films deposited by pulsed laser deposition

The optical properties of N-doped ZnO films grown by pulsed laser deposition are examined for which zinc nitride is used as the source of nitrogen. The motivation for this study is to determine if nitrogen-related acceptor state formation can be achieved in ZnO films using Zn₃N₂ doping in the ablation target. The films were deposited in oxygen or nitrogen on c-plane sapphire. Photoluminescence measurements at 20 K reveal a 3.31 eV acceptor-bound exciton emission due to nitrogen substitution on the oxygen site, donor-acceptor pair emission at 3.23 ± 1 eV and free electron-acceptor at 3.27 eV. The binding energy of the N-related acceptor is estimated to be in the range of 170-15 meV. While the as-deposited films were n-type, thermal annealing in oxygen yielded insulating behavior, consistent with compensating acceptor states.     

Optical investigation of ferromagnetic Ga1−xMnxN layers grown on sapphire (0 0 0 1) substrates

We have investigated the temperature-dependent photoluminescence (PL) spectra in Ga_1−xMn_xN layers (where x≈0.1–0.8%) grown on sapphire (0 0 0 1) substrates using the plasma-enhanced molecular beam epitaxy technique. All the layers doped with manganese exhibited n-type conductivity with Curie temperature over 350 K. The efficient PL are peaked in the red (1.86 eV), yellow (2.34 eV), and blue (3.29 eV) spectral range. It was found that the blue band at 3.29 eV is mostly associated with the formation complexes between donors (e.g., N vacancy) and Mn acceptors, which results in forming donor levels at 0.23 eV below the conduction band edge. The yellow band is attributed to intrinsic gallium defects. The broad band at 1.86 eV is attributed to inner ⁵D state transition (T₂ to E) of Mn ions.     

Studies of luminescence properties of ZnO and ZnO:Zn nanorods prepared by solution growth technique

Pyramidal ZnO nanorods with hexagonal structure having c-axis preferred orientation are grown over large area silica substrates by a simple aqueous solution growth technique. The as-grown nanorods were studied using XRD, SEM and UV-vis photoluminescence (PL) spectroscopy for their structural, morphological and optical properties, respectively. Further, the samples have also been annealed under different atmospheric conditions (air, O₂, N₂ and Zn) to study the defect formation in nanorods. The PL spectra of the as-grown nanorods show narrow-band excitonic emission at 3.03 eV and a broad-band deep-level emission (DLE) related to the defect centers at 2.24 eV. After some mild air annealing at 200 °C, fine structures with peaks having energy separation of ∼100 meV were observed in the DLE band and the same have been attributed to the longitudinal optical (LO) phonon-assisted transitions. However, the annealing of the samples under mild reducing atmospheres of N₂ or zinc at 550 °C resulted in significant modifications in the DLE band wherein high intensity green emission with two closely spaced peaks with maxima at 2.5 and 2.7 eV were observed which have been attributed to the V_O and Zn_i defect centers, respectively. The V-I characteristic of the ZnO:Zn nanorods shows enhancement in n-type conductivity compared to other samples. The studies thus suggest that the green emitting ZnO:Zn nanorods can be used as low voltage field emission display (FED) phosphors with nanometer scale resolution.     

The leakage current mechanisms in the Schottky diode with a thin Al layer insertion between Al0.245Ga0.755N/GaN heterostructure and Ni/Au Schottky contact

This paper investigates the behaviour of the reverse-bias leakage current of the Schottky diode with a thin Al inserting layer inserted between Al0.245Ga0.755 N/GaN heterostructure and Ni/Au Schottky contact in the temperature range of 25-350°C. It compares with the Schottky diode without Aluminium inserting layer. The experimental results show that in the Schottky diode with Al layer the minimum point of I-V curve drifts to the minus voltage, and with the increase of temperature increasing, the minimum point of I-V curve returns the 0 point. The temperature dependence of gate-leakage currents in the novelty diode and the traditional diode are studied. The results show that the Al inserting layer introduces interface states between metal and Al0.245Ga0.755N. Aluminium reacted with oxygen formed Al2O3 insulator layer which suppresses the trap tunnelling current and the trend of thermionic field emission current. The reliability of the diode at the high temperature is improved by inserting a thin Al layer.     

Characterization of nitrogen-doped ZnO thin films grown by plasma-assisted pulsed laser deposition on sapphire substrates

The crystalline, optical and electrical properties of N-doped ZnO thin films were measured using X-ray diffraction, photoluminescence and Hall effect apparatus, respectively. The samples were grown using pulsed laser deposition on sapphire substrates coated priorly with ZnO buffer layers. For the purpose of acceptor doping, an electron cyclotron resonance (ECR) plasma source operated as a low-energy ion source was used for nitrogen incorporation in the samples. The X-ray diffraction analyses indicated some deterioration of the ZnO thin film with nitrogen incorporation. Temperature-dependent Van der Pauw measurements showed consistent p-type behavior over the measured temperature range of 200–450 K, with typical room temperature hole concentrations and mobilities of 5×10¹⁵ cm⁻³ and 7 cm²/V s, respectively. Low temperature photoluminescence spectra consisted of a broad emission band centered around 3.2 eV. This emission is characterized by the absence of the green deep-defect band and the presence of a band around 3.32 eV.     

Modified thermal evaporation process using GeO2 for growing ZnO structures

In the current work, zinc oxide (ZnO) nano/microstructures are synthesized using a modified thermal-evaporation process by introducing germanium oxide (GeO₂) powder mixed with metallic Zn powder as the raw material. Without the use of any catalyst and oxygen flow in the furnace system, GeO₂ is utilized to provide an oxygen source for the growth of ZnO structure. The samples are treated by different temperatures ranging from 500 to 900 °C. Morphology, phase structure, and photoluminescence properties are investigated by scanning electron microscopy (SEM), X-ray diffractometer (XRD) and photoluminescence (PL) spectrometer. The structures and morphologies of the samples were found to vary with growth temperature. The XRD diffraction peaks show that the films grown at temperature from 600 to 800 °C consist of hexagonal wurtzite ZnO structures. Room-temperature PL measurement revealed ZnO spectra representing two bands: near-band-edge emission in the ultraviolet (UV) region and broad deep-level emission centered at about 500 nm. The strong UV emission in the PL spectra indicates that the GeO₂ supplies sufficient oxygen for formation of ZnO structures with few oxygen vacancies. The growth mechanism and the roles of GeO₂ for formation of ZnO structures are discussed in detail.     

Dependences of the surface and the optical properties on the O2/O2 + Ar flow-rate ratios for ZnO thin films grown on ZnO buffer layers

ZnO active layers on ZnO buffer layers were grown at various O₂/O₂ + Ar flow-rate ratios by using radio-frequency magnetron sputtering. Atomic force microscopy images showed that the surface roughnesses of the ZnO active layers grown on ZnO buffer layers decreased with decreasing O₂ atmosphere, indicative of an improvement in the ZnO surfaces. The type of the ZnO active layer was n-type, and the resistivity of the layer increased with increasing O₂ atmosphere. Photoluminescence spectra from the ZnO active layers grown on the ZnO buffer layers showed dominant peaks corresponding to local levels in the ZnO energy gap resulting from oxygen vacancies or interstitial zinc vacancies, and the peak positions changed significantly with the O₂/O₂ + Ar flow rate. These results can help improve understanding of the dependences of the surface and the optical properties on the O₂/O₂ + Ar ratio for ZnO thin films grown on ZnO buffer layers.     

Silicon MIS diodes with Cr2O3 nanofilm: Optical, morphological/structural and electronic transport properties

In this work we report the optical, morphological and structural characterization and diode application of Cr₂O₃ nanofilms grown on p-Si substrates by spin coating and annealing process. X-ray diffraction (XRD), non-contact mode atomic force microscopy (NC-AFM), ultraviolet-visible (UV-vis) spectroscopy and photoluminescence (PL) spectroscopy were used for characterization of nanofilms. For Cr₂O₃ nanofilms, the average particle size determined from XRD and NC-AFM measurements was approximately 70 nm. Structure analyses of nanofilms demonstrate that the single phase Cr₂O₃ on silicon substrate is of high a crystalline structure with a dominant in hexagonal (1 1 0) orientation. The morphologic analysis of the films indicates that the films formed from hexagonal nanoparticles are with low roughness and uniform. UV-vis absorption measurements indicate that the band gap of the Cr₂O₃ film is 3.08 eV. The PL measurement shows that the Cr₂O₃ nanofilm has a strong and narrow ultraviolet emission, which facilitates potential applications in future photoelectric nanodevices. Au/Cr₂O₃/p-Si metal/interlayer/semiconductor (MIS) diodes were fabricated for investigation of the electronic properties such as current-voltage and capacitance-voltage. Ideality factor and barrier height for Au//Cr₂O₃/p-Si diode were calculated as 2.15 eV and 0.74 eV, respectively. Also, interfacial state properties of the MIS diode were determined. The interface-state density of the MIS diode was found to vary from 2.90 × 10¹³ eV⁻¹ cm⁻² to 8.45 × 10¹² eV⁻¹ cm⁻².     

Pulsed laser deposited ZnO/ZnO:Li multilayer for blue light emitting diodes

Thin films of ZnO, Li doped ZnO (ZLO) and multilayer of ZnO and ZLO (ZnO/ZLO) were grown on silicon and corning glass substrates by pulsed laser deposition technique. Single phase formation and the crystalline qualities of the films were analyzed by X-ray diffraction and Li composition in the film was investigated to be 15 wt% by X-ray photoelectron spectroscopy. Raman spectrum reveals the hexagonal wurtzite structure of ZnO, ZLO and ZnO/ZLO multilayer and confirms the single phase formation. Films grown on corning glass shows more than 80% transmittance in the visible region and the optical band gaps were calculated to be 3.245, 3.26 and 3.22 eV for ZnO, ZLO and ZnO/ZLO, respectively. An efficient blue emission was observed in all films which were grown on silicon (1 0 0) substrate by photoluminescence (PL). PL measurements at different temperatures reveal that the PL emission intensity of ZnO/ZLO multilayer was weakly dependent on temperature as compared to the single layers of ZnO and ZLO and the wavelength of emission was independent of temperature. Our results indicate that ZnO/ZLO multilayer can be used for the fabrication of blue light emitting diodes.     

Site-specific interaction of H2O with ZnO single-crystal surfaces studied by thermal desorption and UV photoelectron spectroscopy

The adsorption and condensation of H₂O(D₂O) on ZnO(101̄0), (0001)Zn and (0001̄)O surfaces was investigated by means of thermal desorption (TDS) and UV photoelectron spectroscopy (UPS). The clean ZnO single-crystal surfaces were prepared by Ar-ion sputtering and annealing and characterised by Auger electron spectroscopy, LEED, UPS and work-function measurements. On all three surfaces six different adsorption states were found. In the monolayer regime there is a stronger bonding to Zn sites (desorption temperature 340 K) than to O sites (190 K), The bonding to the Zn sites seems to be accompanied by some clustering. Before the chemisorption layer is completed a first ice state is found whose desorption temperature shifts from 162 to 168 K with increasing exposures. At higher exposures the multilayer ice state is found at 152 K. On the (0001̄)O face defect-induced features were identified. The water lone-pair orbital 1b₁, whose energy falls between the O p and the Zn 3d emission of the substrate and which is known to show bonding shifts, was analysed using angle-resolved UPS. In the monolayer, the main chemisorption states are found at E_B^V(1b₁) = ?9.6 eV for the (0001)Zn face and at ? 10.6 eV for the (0001̄)O face and are compared with the multilayer ice emission at 1̄1.1 eV. The difference in binding energies shows the same trend as the TDS data. For the (101̄0) face the 1b₁ emission is very broad, indicating some overlap between different states.     

Photoluminescence investigation of ferromagnetic Ga1−xMnxN layers with GaN templates grown on sapphire (0 0 0 1) substrates

We have investigated the temperature and composition dependent photoluminescence (PL) spectra in Ga_1−xMn_xN layers (where x ≈ 0.1-0.8%) grown on sapphire (0 0 0 1) substrates using the plasma-enhanced molecular beam epitaxy technique. The efficient PL is peaked in the red (1.86 eV), yellow (2.34 eV), and blue (3.29 eV) spectral range. The band-gap energy of the Ga_1−xMn_xN layers decreased with increasing temperature and manganese composition. The band-gap energy of the Ga_1−xMn_xN layers was modeled by the Varshni equation and the parameters were determined to be α = 2.3 × 10⁻⁴, 2.7 × 10⁻⁴, 3.4 × 10⁻⁴ eV/K and β = 210, 210, and 230 K for the manganese composition x = 0.1%, 0.2%, and 0.8%, respectively. As the Mn concentration in the Ga_1−xMn_xN layers increased, the temperature dependence of the band-gap energy was clearly reduced.     

ZnO films grown by laser ablation with and without oxygen CVD

In the present work we have studied the properties of zinc oxide (ZnO) thin films grown by laser ablation of ZnO targets under different substrate temperature and background oxygen conditions. The ZnO layers were deposited with a Pulsed Laser Deposition (PLD) system on pre-nitrided (0001) sapphire (Al₂O₃), using the base line of a Nd:YAG laser at 1064 nm. The films were characterized by different structural and optical methods, including X-ray diffraction (XRD), scanning electron microscopy (SEM), optical transmission spectroscopy, and steady-state photoluminescence (PL). XRD analysis with rocking curves and θ–2θ scans indicates preferential growth along the c-axis direction with a full width at half maximum (FWHM) smaller than 1.5. Low-temperature photoluminescence (PL) showed strong excitonic emission near 3.36 eV between 9 and 65 K.     

Low temperature photoluminescence and photoacoustic characterization of Zn-doped InxGa1−xAsySb1−y epitaxial layers for photovoltaic applications

In this paper we present results on the characterization of Zn-doped InGaAsSb epitaxial layers to be used in the development of stacked solar cells. Using the liquid phase epitaxy technique we have grown p-type InGaAsSb layers, using Zn as the dopant, and n-type Te-doped GaSb wafers as substrates. A series of Zn-doped InGaAsSb samples were prepared by changing the amount of Zn in the melt in the range: 0.1-0.9 mg to obtain different p-type doping levels, and consequently, different p-n region characteristics. Low temperature photoluminescence spectra (PL) were measured at 15 K using at various excitation powers in the range 80-160 mW. PL spectra show the presence of an exciton-related band emission around 0.642 eV and a band at 0.633 eV which we have related to radiative emission involving Zn-acceptors. Using the photoacoustic technique we measured the interface recombination velocities related to the interface crystalline quality, showing that the layer-substrate interface quality degrades as the Zn concentration in the layers increases.     

Optical and structural properties of MgZnO/ZnO hetero- and double heterostructures grown by pulsed laser deposition

MgZnO thin films, MgZnO/ZnO heterostructures (HS) and double heterostructures (DHS) have been prepared on a-plane sapphire substrates by means of pulsed laser deposition (PLD). A linear blueshift of the MgZnO emission with increasing Mg content is observed in photoluminescence spectroscopy (PL) at 2 K. Cathodoluminescence measurements verify the spatial homogeneity of the emission properties of the MgZnO films. The film roughness is evaluated from atomic force microscopy scans. In MgZnO/ZnO HS the ZnO grows on all appearing MgZnO facets. PL investigations of such PLD-grown heterostructures show the high optical quality of thin ZnO films (d≤100 nm) grown on MgZnO. Capping those structures with a thin MgZnO layer further improves their luminescence intensity and enhances the emission of free-exciton luminescence from the ZnO layers. MgZnO/ZnO/MgZnO DHS with nominal ZnO layer thicknesses of d_nom≤6 nm show a clear intensification of the ZnO PL. Temperature dependent PL and transmission measurements between 4.4 and 300 K prove the dominating emission to be due to the recombination of excitons localized in the ZnO. At 2 K, due to confinement effects, their emission energy is blueshifted up to 51 meV compared to free excitons in bulk ZnO. PACS 81.15.Fg; 78.66.Hf; 68.37.Ps     

Optical properties of In2O3 oxidized from InN deposited by reactive magnetron sputtering

Unintentionally doped and zinc-doped indium nitride (U-InN and InN:Zn) films were deposited on (0 0 0 1) sapphire substrates by radio-frequency reactive magnetron sputtering, and all samples were then treated by annealing to form In₂O₃ films. U-InN and InN:Zn films have similar photon absorption characteristics. The as-deposited U-InN and InN:Zn film show the absorption edge, ∼1.8-1.9 eV. After the annealing process at 500 °C for 20 min, the absorption coefficient at the visible range apparently decreases, and the absorption edge is about 3.5 eV. Two emission peaks at 3.342 eV (371 nm) and 3.238 eV (383 nm) in the 20 K photoluminescence (PL) spectrum of In₂O₃:Zn films were identified as the free-exciton (FE) or the near band-to-band (B-B) and conduction-band-to-acceptor (C-A) recombination, respectively.     

Growth of wide band gap wurtzite ZnMgO layers on (0001) Al2O3 by radical-source molecular beam epitaxy

Wurtzite structure ZnMgO layers have been grown using radical-source molecular beam epitaxy on high-quality ZnO buffer layers grown on (0001) sapphire substrates. The thickness of the ZnO buffer layers is 300 nm, with full width at half maxim of the HR-XRD (0002) rocking curves as low as 25 arcsec. In-situ Reflection High-Energy Electron Diffraction (RHEED) was employed for the optimization of the ZnMgO growth. RHEED and X-Ray Diffractometry measurements did not reveal any phase change from the wurzite structure to the rocksalt structure. The C-lattice parameter of Zn_1−xMg_xO films decreased from 5.209 to 5.176 Å with increasing x to 0.2. The surface morphology of the samples was studied with atomic force microscopy. The root mean square roughness values of 200 nm thick ZnMgO (x=0.2) was less than 1 nm. The main photoluminescence peak of Zn_1−xMg_xO shifted to as high as 3.77 eV owing to the increasing Mg composition of up to x=0.2.     

Analysis of electrical characteristics of Er/p-InP Schottky diode at high temperature range

We report on the temperature-dependent electrical characteristics of Er/p-InP Schottky barrier diodes. The current–voltage (I–V) and capacitance–voltage (C–V) measurements have been carried out in the temperature range of 300–400 K. Using thermionic emission (TE) theory, the zero-bias barrier height (Φ_bo) and ideality factor (n) are estimated from I–V characteristics. It is observed that there is a decrease in n and an increase in the Φ_bo with an increase in temperature. The barrier height inhomogenity at the metal/semiconductor (MS) interface resulted in Gaussian distribution of Φ_bo and n. The laterally homogeneous Schottky barrier height value of approximately 1.008 eV for the Er/p-InP Schottky barrier diodes is extracted from the linear relationship between the experimental zero-bias barrier heights and ideality factors. The series resistance (R_s) is calculated by Chenug's method and it is found that it increases with the decrease in temperature. The reverse-bias leakage current mechanism of Er/p-InP Schottky diode is investigated. Both Poole–Frenkel and Schottky emissions are described and discussed. Furthermore, capacitance–voltage (C–V) measurements of the Er/p-InP Schottky contacts are also carried out at room temperature in dark at different frequencies of 10, 100 and 1000 kHz. Using Terman's method, the interface state density is calculated for Er/p-InP Schottky diode at different temperatures.     

Optical investigation of A-plane ZnO/ZnMgO multiple quantum wells grown by pulsed laser deposition

In this study, we present the optical characteristics of A-plane ZnO/ZnMgO multiple quantum wells (MQWs) with different well widths grown on R-plane sapphire substrates by pulsed laser deposition (PLD). The energy gaps of ZnO and ZnMgO have been observed by photoluminescence (PL) and absorption spectra. The electrons confined in the ZnO wells transit from the electron ground sub-band to the heavy-hole ground sub-band (noted as 11H) located at 3.40 and 3.57 eV for the ZnO/ZnMgO MQWs samples with well widths of 5.6 and 1.2 nm, respectively. The strong anisotropic polarization characteristic has been studied by polarization-dependent PL measurements. For comparison, we also calculated the transition energies of different well thicknesses varying from 1 to 6 nm. The theoretical results match quite well with the experimental values and revealing the suitable conduction band offset Q_c=0.6. The temperature dependence of PL spectra is being investigated, in the temperature range between 10 and 300 K.     

Deep level states and negative photoconductivity in n-ZnO/p-Si hetero-junction diodes

Negative photoconductivity (NPC) was observed in n-ZnO/p-Si heterojunction diode grown by ultra-high vacuum sputtering method under nitrogen ambient. Under the illumination of ultra-violet light, positive photoconductivity was observed at low bias voltages, whereas NPC was observed at high bias voltages. The defect states in the ZnO layers grown on Si were analyzed by photoluminescence and deep level transient spectroscopy measurements. Two deep levels were measured at E_c-0.51 eV and E_c-0.54 eV, which might be originated from oxygen vacancy and nitrogen atom related defects, respectively. Based on the simulation of band diagram, the defect states were located below Fermi level at zero bias voltage. However, as increasing the bias voltages, NPC was observed due to the increase of empty defect states. This analysis allowed us to consider the possibility that the NPC phenomenon in n-ZnO/p-Si heterojunction diode is originated dominantly from the defect states as a carrier recombination center in ZnO layer.     

Comparative PL study of individual ZnO nanorods,grown by APMOCVD and CBD techniques

The photoluminescence properties of individual ZnO nanorods, grown by atmospheric pressure metalorganic chemical vapor deposition (APMOCV) and chemical bath deposition (CBD) are investigated by means of temperature dependent micro-PL. It was found that the low temperature PL spectra are driven by neutral donor bound exciton emission D⁰X, peaked at 3.359 and 3.363 eV for APMOCVD and CBD ZnO nanorods, respectively. The temperature increase causes a red energy shift of the peaks and enhancement of the free excitonic emission (FX). The FX was found to dominate after 150 K for both samples. It was observed that while APMOCVD ZnO nanorods possess a constant low signal of visible deep level emission with temperature, the ZnO nanorods grown by CBD revealed the thermal activation of deep level emission (DLE) after 130 K. The resulting room temperature DLE was a wide band located at 420–550 nm. The PL properties of individual ZnO nanorods can be of importance for their forthcoming application in future optoelectronics and photonics.