Polyaniline-poly(vinyl alcohol) IPN-composite prepared from potassium dichromate embedded PVA film: a material for humidity sensing application

Polyaniline-polyvinyl alcohol (PANI-PVA) interpenetrating network composite film is successfully prepared by in situ polymerization of aniline within PVA film embedded with different concentrations of potassium dichromate (K₂Cr₂O₇). The resulted composite is characterized by UV-Visible spectroscopy, SEM and XRD, TGA techniques and confirmed the formation of interpenetrating network formation of PANI within PVA matrix. Electrical conductivity of the composite films increase from 10⁻⁶ to 10⁻² S/cm with the increase in the loading of dichromate from 10⁻⁴ to 10⁻² M. Further, exposing in humidity environment, the conductivity of the composite films increases from 14 to 100% with the increase in humidity conditions from 11.3 to 84.3%.     

Preparation and antibacterial effect of silver-hydroxyapatite/titania nanocomposite thin film on titanium

The composite which contains Ag⁺ and nanosized hydroxyapatite with TiO₂ was deposited onto titanium by dipping method. The morphology, chemical components and structures of the thin film were characterized by XRD, scanning electronic microscope (SEM) and energy dispersive X-ray analysis (EDX). Staphylococcus aureus and Escherichia coli were utilized to test the antibacterial effect. XRD results demonstrated that the films have characteristic diffraction peaks of pure HA. EDX results showed that the deposited films consisted of Ca, P, Ti, O and Ag, all of which distribute uniformly. With regard to the antibacterial effect, 98% of S. aureus and more than 99% of E. coli were killed after 24 h incubation and pictures of SEM showed obviously fewer cells on the surface with coating.     

Synthesis of nano-crystalline zirconium aluminium oxynitride (ZrAlON) composite films by dense plasma Focus device

Zirconium aluminium oxynitride multiphase composite film is deposited on zirconium substrate using energetic nitrogen ions delivered from dense plasma Focus device. X-ray diffractometer (XRD) results show that five Focus shots are sufficient to initiate the nucleation of ZrN and Al₂O₃ whereas 10 Focus shots are sufficient to initiate the nucleation of AlN. XRD results reveal that crystal growth of nitrides/oxides increases by increasing Focus shots (up to 30 Focus shots) and resputtering of the previously deposited film is taken place by further increase in Focus shots (40 Focus shots). Scanning electron microscopic (SEM) results indicate the uniform distribution of spherical grains (∼35 nm). A smoother surface is observed for 20 Focus shots at 0° angular position. SEM results also show a net-type microstructure (thread like features) of the sample treated for 30 Focus shots whereas rough surface morphology is observed for 40 Focus shots. Energy dispersive spectroscopic profiles show the distribution of different elements present in the deposited composite films. A typical microhardness value of the deposited composite films is 5255 ± 10 MPa for 10 grams imposed load which is 3.3 times than the microhardness values of unexposed sample. The microhardness values of the exposed samples increases with increasing Focus shots (up to 30 Focus shots) and decreases for 40 Focus shots treatment due to resputtering of the previously deposited composite film. The microhardness values of the composite films decreases by increasing the sample's angular position.     

Structural, optical and electrical properties of tin oxide thin film deposited by APCVD method

Tin oxide (SnO₂) thin films have been grown on glass substrates using atmospheric pressure chemical vapour deposition (APCVD) method. During the deposition, the substrate temperature was kept at 400°C–500°C. The structural properties, surface morphology and chemical composition of the deposited film were studied by X-ray diffraction (XRD), scanning electron microscope (SEM) and Rutherford back scattering (RBS) spectrum. XRD pattern showed that the preferred orientation was (110) having tetragonal structure. The optical properties of the films were studied by measuring the transmittance, absorbance and reflectance spectra between λ = 254 nm to 1400 nm and the optical constants were calculated. Typical SnO₂ film transmits ∼ 94% of visible light. The electrical properties of the films were studied using four-probe method and Hall-voltage measurement experiment. The films showed room temperature conductivity in the range 1.08 × 10² to 1.69 × 10² Ω⁻¹cm⁻¹.     

Energy harvesting of PZT/PMMA composite flexible films

Polymer/lead zirconate titanate {[Pb(Zr_x, Ti_1-x)O₃], PZT, x = 0.40} flexible composite films are prepared by solvent evaporation technique. Carbon tape used as a top and bottom electrodes for fabricating flexible PZT composite films. The phase purity and functional groups of PZT and polymer humps are confirmed by XRD and FTIR respectively. XPS analysis showed that PMMA contains carbon (C) and oxygen (O). Carbon (C), oxygen (O), lead (Pb), zirconium (Zr) and titanium (Ti) are present in PZT/PMMA composite films. The chemical states of Pb, Zr and Ti ions are 2⁺, 4⁺ and 4⁺ respectively confirmed by XPS. The higher forefinger bending motion of the film is found to reveal greater output voltage (5.2 V) than the output voltage (1.6 V) for slight bending motion of the forefinger. Therefore, based on the results human mechanical forces induce compressive stress on PZTs ferroelectric based composite films and are excellent candidate for energy harvester.     

Preparation, structures and photoluminescent enhancement of CdWO4-TiO2 composite nanofilms

For the first time, Cadmium tungstate (CdWO₄)-TiO₂ composite nanofilms on a glass substrate were prepared by means of the dip-coating technique, in which collodion was used as a dispersant and film-forming agent. The films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), thermo gravimetric and thermal analyses (TG/DTA), FTIR and photoluminescence (PL) methods, respectively. SEM and XRD characterization of these films indicated that CdWO₄ particles crystallized in a monoclinic wolframite-type structure whereas TiO₂ particles were Anatase phase; and both of them were well distributed in the nanofilms. FTIR spectra proved the presence of CdWO₄ on the nanofilms. Photoluminescent results showed that the emitting peak of CdWO₄ films blue shifted slightly relative to that of CdWO₄ crystal. Moreover, the PL intensity of CdWO₄-TiO₂ composite nanofilm was much higher than that of CdWO₄ nanofilm. We ascribed that the introduction of TiO₂ should be responsible for the PL enhancement.     

Gelatin–Chitosan composite capped gold nanoparticles: a matrix for the growth of hydroxyapatite

Growth of hydroxyapatite (HA) on gelatin–chitosan composite capped gold nanoparticles is presented for the first time by employing wet precipitation methods and we obtained good yields of HA. Fourier transform infrared spectroscopy (FTIR) spectrum has shown the characteristic bands of phosphate groups in the HA. Scanning electron microscopy (SEM) pictures have shown spherical nanoparticles with the size in the range of 70–250 nm, whereas ≥2–50 nm sized particles were visualized in high resolution transmission electron microscopy (HR-TEM). X-ray diffraction (XRD) spectrum has shown Bragg reflections which are comparable with the HA. Energy dispersive X-ray (EDX) studies have confirmed calcium/phosphate stoichiometric ratio of HA. The thermogravimetric analysis (TGA) has shown about 74% of inorganic crystals in the nanocomposite formed. These results have revealed that gelatin–chitosan capped gold nanoparticles, acted as a matrix for the growth of HA.     

Structural and ionic conductivity studies of solid polymer electrolytes based on poly (vinylchloride) and poly (methylmethacrylate) blends

Thin film of poly (vinylchloride) and poly (methylmethacrylate) blend polymer electrolytes plasticized with a combination of DBP and Li₂SO₄ salts have been prepared by solution casting technique. The prepared films were subjected to a.c. impedance measurements as a function of temperature ranging from 304–373 K. The maximum conductivity at 304 K was found to be 1.24 × 10⁻⁸ S·cm⁻¹ for PVC-PMMA-Li₂SO₄-DBP (7.5-17.5-5-70 mole-%). Temperature dependence studies on the ionic conductivity in the PVC-PMMA-Li₂SO₄-DBP system suggest that the ion conduction follows the Williams-Landel-Ferry (WLF) mechanism, which is further confirmed by Vogel-Tamman-Fulcher (VTF) plots. XRD, FTIR, SEM and thermal studies revealed complex formation in.     

Synthesis and characterization of silver-polypyrrole film composite

In this work, we report the chemical polymerization of pyrrole to obtain thin film of polypyrrole (PPy) hydrochloride deposited onto the electrode of the quartz crystal microbalance (QCM). The film in the base form was exposed to a solution of AgNO₃. Electroless reduction for silver ions by the PPy film took place and silver particles were adsorbed onto the film surface. The silver particles content at the PPy films were analyzed by QCM and the results showed that the concentrations of silver uptakes increase as the original AgNO₃ solution increases. The morphology of the surface of the PPy film and the silver-PPy film composite were studied by the scanning electron microscopy (SEM) coupled with energy dispersive X-ray spectrometry (EDX). They showed that the obtained silver particles have spherical, cubic and tetrahedral structures. X-ray diffraction (XRD) and Fourier transformed infra-red spectroscopy (FTIR) were used to characterize the structure of the powder composite. This work reveals the capability of PPy film coating on QCM in sensing and removing silver from several environmental samples.     

The synthesis and kinetic growth of anisotropic silver particles loaded on TiO2 surface by photoelectrochemical reduction method

Silver nanorods with average diameters of 120-230 nm and aspect ratio of 1.7-5.0 were deposited on the surface of TiO₂ films by photoelectrochemical reduction of Ag⁺ to Ag under UV light. The composite films prepared on soda-lime glass substrates were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The results show that the TiO₂ film after UV irradiation in AgNO₃ solution is composed of anatase phase TiO₂ and metallic silver with face centered cubic structure. Other compounds cannot be found in the final films. The maximum deposition content of silver particles on the surface of TiO₂ film was obtained with the AgNO₃ concentration of 0.1 M. The kinetic growth rates of silver particles can be controlled by photocatalytic activity of TiO₂ films. The studies suggest that the growth rates of silver particles increase with the enhancement of photocatalytic activity of TiO₂ films. The maximum growth rate of silver particles loaded on TiO₂ films can be up to 0.353 nm min⁻¹ among samples 1#, 2# and 3#, while the corresponding apparent rate constant of TiO₂ is 1.751 × 10⁻³ min⁻¹.     

Ionic conductivity studies in PMMA/PVdF polymer blend electrolyte with lithium salts

Batteries using ionically conducting polymer membranes as electrolytes are very attractive, since the concept of power sources capable of combining a high energy content with plasticity is very appealing for the consumer electronics market and in electric vehicle applications. Blend based polymer electrolytes composed of poly (methylmethacrylate) (PMMA), Poly Vinylidene fluoride (PVdF), Lithium salt (LiX) (X=ClO₄, BF₄ and CF₃SO₃) and Dimethyl Phthalate (DMP) are prepared using solvent casting technique. The films have been characterized using XRD, FTIR, Thermal and SEM studies; the effect of complexing salt and temperature on ionic conductivity is also discussed. The maximum conductivity value obtained for the solid polymer electrolyte film at 303 K is 4.2 × 10⁻³ S/cm.     

A comparative study of lithium and sodium salts in PAN-based ion conducting polymer electrolytes

The conducting polymer electrolyte films consisting of polyacrylonitrile (PAN) as the host polymer, lithium triflate (LiCF₃SO₃) and sodium triflate (NaCF₃SO₃) as inorganic salts were prepared by the solution-cast technique. The pure PAN film was prepared as a reference. The ionic conductivity for the films is characterized using impedance spectroscopy. The room temperature conductivity for the PAN + 26 wt.% LiCF₃SO₃ film and the PAN + 24 wt.% NaCF₃SO₃ film is 3.04 × 10⁻⁴ S cm⁻¹ and 7.13 × 10⁻⁴ S cm⁻¹, respectively. XRD studies show that the complexation that has occurred in the PAN containing salt films and complexes formed are amorphous. The FTIR spectra results confirmed the complexation has taken place between the salt and the polymer. These results correspond with surface morphology images obtained from SEM analysis. The conductivity–temperature dependence of the highest conducting film from PAN + LiCF₃SO₃ and PAN + NaCF₃SO₃ systems follows Arrhenius equation in the temperature range of 303 to 353 K. The PAN containing 24 wt.% LiCF₃SO₃ film has a higher ionic conductivity and lower activation energy compared to the PAN containing 26 wt.%LiCF₃SO₃ film. These results can be explained based on the Lewis acidity of the alkali ions, i.e., the interaction between Li⁺ ion and the nitrogen atom of PAN is stronger than that of Na⁺ ion.     

Surface modification of polyacrylonitrile film by anchoring conductive polyaniline and determination of uricase adsorption capacity and activity

Polyacrylonitrile (PAN) films were modified with chemical polymerization of conductive polyaniline (PANI) in the presence of potassium dichromate as an oxidizing agent. The effect of aniline concentration on the grafting efficiency and on the electrical surface resistance of PAN and (PAN/PANI)-1-3 composite film was investigated. The surface resistances of the conductive composite films were found to be between 6.32 and 0.97 kΩ/cm. As the amount of grafted PANI increased on the PAN films, the electrical resistance of composite film decreased. The PAN/PANI composite films were also characterized using SEM and FTIR. The changes in the surface properties of the films were characterized by contact angle measurements. As expected, the PAN, PAN/PANI and PAN/PANI-uricase immobilized films, exhibited different contact angle values and surface free energy due to different interactive functional groups of the films.The conductive films were well characterized and used for immobilization of uricase. The amount of adsorbed enzyme increases with the increase of surface concentration of grafted fibrous polyaniline polymer. The maximum amount of immobilized enzyme onto composite film containing 2.4% PANI was about 216 μg/cm² (i.e., PAN/PANI-3). The immobilized uricase was reused 24 times in batch wise assay in a day. Finally, the immobilized uricase enzyme system was successfully fabricated and applied to determine the uric acid level in human serum samples.     

Experimental investigations on plasticized PMMA/PVA polymer blend electrolytes

Blend based polymer electrolytes composed of poly (methyl methacrylate) (PMMA), poly(vinylalcohol) (PVA) and LiClO₄ are prepared using solvent casting technique. The polymer films are characterized by XRD and FTIR studies to determine the molecular environment for the conducting ions. These polymer films have been investigated in terms of ionic conductivity using the results of impedance studies. The influence of the blend composition on the electrochemical behaviour is also discussed. The highest room temperature conductivity obtained for the film consisting of PMMA, PVA, LiClO₄ and DMP is 0.06×10⁻³ S/cm at 303 K. The PMMA-PVA blend based polymer electrolytes look very desirable and promising for lithium battery applications.     

Influence of 120 MeV Si9+ ion irradiation on ZnTe semiconductor thin films

ABSTRACT

ZnTe (Zinc Telluride) is a potential semiconducting material for many optoelectronic devices like solar cells and back contact material for CdTe-based solar cells. In the present study, ZnTe thin films were prepared by thermal evaporation technique and then irradiated with 120?MeV Si⁹⁺ ions at different fluences. These films are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and UV–Visible spectroscopy techniques. XRD study confirms increased crystallinity and grain growth for post-irradiated ZnTe thin films for fluences, up to 1?×?10¹¹ ions cm^?2. However, the grain size and crystallinity decreased for higher fluence-exposed samples. SEM images confirm the observed structural properties. Modification of the surface morphology of the film due to the ion irradiation with different fluences is studied. Optical band gap of film is decreased from 2.31?eV (pristine) to 2.17?eV after irradiation of Si⁹⁺ ions.     

Bioglass thin films for biomimetic implants

Pulsed laser deposition (PLD) method was used to obtain bioglass (BG) thin film coatings on titanium substrates. An UV excimer laser KrF* (λ = 248 nm, τ = 25 ns) was used for the multi-pulse irradiation of the BG targets with 57 or 61 wt.% SiO₂ content (and Na₂O-K₂O-CaO-MgO-P₂O₅ oxides). The depositions were performed in oxygen atmosphere at 13 Pa and for substrates temperature of 400 °C. The PLD films displayed typical BG of 2-5 μm particulates nucleated on the film surface or embedded in. The PLD films stoichiometry was found to be the same as the targets. XRD spectra have shown, the glass coatings obtained, had an amorphous structure. One set of samples, deposited in the same conditions, were dipped in simulated body fluids (SBFs) and subsequently extracted one by one after several time intervals 1, 3, 7, 14 and 21 days. After washing in deionized water and drying, the surface morphology of the samples and theirs composition were investigated by scanning electron microscopy (SEM), X-ray diffraction (XRD), IR spectroscopy (FTIR) and energy dispersive X-ray analysis (EDX). After 3-7 days the Si content substantially decreases in the coatings and PO₄³⁻ maxima start to increase in FTIR spectra. The XRD spectra also confirm this evolution. After 14-21 days the XRD peaks show a crystallized fraction of the carbonated hydroxyapatite (HAP). The SEM micrographs show also significant changes of the films surface morphology. The coalescence of the BG droplets can be seen. The dissolution and growth processes could be assigned to the ionic exchange between BG and SBFs.     

Study of field emission and dielectric properties of AlN films prepared by DC sputtering technique at different substrate temperatures

Nanocrystalline AlN thin films were prepared via DC sputtering technique at different substrate temperature. The crystal orientation and particle size of aluminum nitride thin films were investigated by XRD analysis. Study indicated that the sample contained pure phase hexagonal AlN nanoparticles with a single peak corresponding to the (100) planes. The peak at 665 cm⁻¹ in the FTIR spectrum of film was assigned to the LO phonon of hexagonal AlN. The particle size of the film, prepared at substrate temperature 200°C was about 9.5 nm, as investigated by atomic force microscope. Field emission study indicated that it can be used as a good field emitter. Turn-on field (E_to) of 15.02 V/μm was observed for the AlN films synthesized at substrate temperature 200°C. Dielectric constant of the AlN film was found nearly independent of frequencies in the measured frequency range 1 KHz to 1 MHz, i.e. in the audio frequency range. The values of dielectric constant (ε) were 10.07, 9.46 and 8.65 for the film prepared at 70°C, 150°C and 200°C, respectively, at frequency 1 KHz.     

Growth and characterization of Mg(OH)2 film on magnesium alloy AZ31

Magnesium-based biomaterials have been proposed as potential candidates for biodegradable implant materials, such as bone screws, bone plates, intraluminal stents and so on. However, the poor corrosion resistance inhibits their applications in surgery. They collapse before the injured tissues are healed. In this paper, Mg(OH)₂ nonstructural film was synthesized on the substrate of AZ31 magnesium alloy by hydrothermal method with NaOH solution as mineralizer to reduce the corrosion rate of magnesium-based materials. The obtained films were characterized by XRD, SEM, and XPS. The results showed that a Mg(OH)₂ film with nanostructure surface can be synthesized by hydrothermal method. It was observed that the thickness of film increased with the holding time. Corrosion rates of the films were studied by immersing the samples in Hank's solution (37 °C). Surface deposits of samples with films soaked in Hank's solution for 31 days were investigated by XRD, SEM, EDS, XPS, and FTIR. It verified that the corrosion rate of the magnesium alloy with grown film was slowed down in the Hank's solution and the behavior of corrosion was inhibited effectively. Amorphous calcium apatite precursor was observed to deposit on the surface of the film during corrosion experiments in Hank's solution. And the tape test revealed a strong adhesion between the film and the substrate.     

Synthesis and microstructure of metal oxide thin films containing metal nanoparticles by liquid phase deposition (LPD) method

Au nanoparticles dispersed SiO₂-TiO₂ composite films have been prepared by a novel wet process, Liquid Phase Deposition (LPD) method. The composite films were characterized by XRD, XPS, TEM, ICP, SEM and UV-VIS absorption spectroscopy. The results showed that the SiO₂-TiO₂ composite films containing Au^III and Au^I ionic species were co-deposited from a mixed solution of ammonium silicofluoride, ammonium hexafluorotitanate, boric acid and tetrachloroauric acid. The heat treatment induced the reduction of Au ions and formation of Au nanoparticles in the film. TEM observation revealed that the Au nanoparticles with 5-10 nm in diameter were found to be dispersed uniformly in the SiO₂-TiO₂ matrix. The optical absorption band due to the surface plasmon resonance of dispersed Au particles were observed at the wavelength of 550 nm and shifted toward longer wavelength with increasing heat treatment temperature. Received 28 November 2000     

Electrocatalytic oxidation of formaldehyde on platinum well-dispersed into single-wall carbon nanotube/polyaniline composite film

Single-walled carbon nanotubes (SWNTs)/polyaniline (PANI) composite films with good uniformity and dispersion were prepared by electrochemical polymerization of aniline containing well-dissolved SWNTs. The composite films were dispersed Pt by electrodeposition technique. The presence of SWNTs and platinum in the composite film was confirmed by XRD analysis and scanning electron microscopy (SEM). Four-point probe investigation and electrochemical impedance spectroscopy (EIS) revealed that the well arrangement of PANI coated SWNTs in these films enhanced electric conductivity and facilitated the charge-transfer of the composite films. Cyclic voltammogram (CV) and chronoamperogram showed that Pt-modified SWNT/PANI composite film performs higher electrocatalytic activity and better long-term stability than Pt-modified pure PANI film toward formaldehyde oxidation. The results imply that the SWNT/PANI composite film as a promising support material improves the electrocatalytic activity for formaldehyde oxidation greatly.