Influence of synthesis method on structural and magnetic properties of cobalt ferrite nanoparticles

The Co–ferrite nanoparticles having a relatively uniform size distribution around 8 nm were synthesized by three different methods. A simple co-precipitation from aqueous solutions and a co-precipitation in an environment of microemulsions are low temperature methods (50 °C), whereas a thermal decomposition of organo-metallic complexes was performed at elevated temperature of 290 °C. The X-ray diffractometry (XRD) showed spinel structure, and the high-resolution transmission electron microscopy (HRTEM) a good crystallinity of all the nanoparticles. Energy-dispersive X-ray spectroscopy (EDS) showed the composition close to stoichiometric (~CoFe₂O₄) for both co-precipitated nanoparticles, whereas the nanoparticles prepared by the thermal decomposition were Co-deficient (~Co_0.6Fe_2.4O₄). The X-ray absorption near-edge structure (XANES) analysis showed Co valence of 2+ in all the samples, Fe valence 3+ in both co-precipitated samples, but average Fe valence of 2.7+ in the sample synthesized by thermal decomposition. The variations in cation distribution within the spinel lattice were observed by structural refinement of X-ray absorption fine structure (EXAFS). Like the bulk CoFe₂O₄, the nanoparticles synthesized at elevated temperature using thermal decomposition displayed inverse spinel structure with the Co ions occupying predominantly octahedral lattice sites, whereas co-precipitated samples showed considerable proportion of cobalt ions occupying tetrahedral sites (nearly 1/3 for the nanoparticles synthesized by co-precipitation from aqueous solutions and almost 1/4 for the nanoparticles synthesized in microemulsions). Magnetic measurements performed at room temperature and at 10 K were in good agreement with the nanoparticles’ composition and the cation distribution in their structure. The presented study clearly shows that the distribution of the cations within the spinel lattice of the ferrite nanoparticles, and consequently their magnetic properties are strongly affected by the synthesis method used.     

Characterization and luminescent properties of SiO2:ZnS:Mn and ZnS:Mn nanophosphors synthesized by a sol-gel method

ZnS and SiO₂-ZnS nanophosphors, with or without different concentration of Mn²⁺ activator ions, were synthesized by using a sol-gel method. Dried gels were annealed at 600 °C for 2 h. Structure, morphology and particle sizes of the samples were determined by using X-ray diffraction (XRD), highresolution transmission electron microscopy (HRTEM) and field emission scanning electron microscopy (FESEM). The diffraction peaks associated with the zincblende and the wurtzite structures of ZnS were detected from as prepared ZnS powders and additional diffraction peaks associated with ZnO were detected from the annealed powders. The particle sizes of the ZnS powders were shown to increase from 3 to 50 nm when the powders were annealed at 600 °C. An UV-Vis spectrophotometer and a 325 nm He-Cd laser were used to investigate luminescent properties of the samples in air at room temperature. The bandgap of ZnS nanoparticles estimated from the UV-Vis data was 4.1 eV. Enhanced orange photoluminescence (PL) associated with ⁴T₁→⁶A₁ transitions of Mn²⁺ was observed from as prepared ZnS:Mn²⁺and SiO₂-ZnS:Mn²⁺ powders at 600 nm when the concentration of Mn²⁺ was varied from 2-20 mol%. This emission was suppressed when the powders were annealed at 600 °C resulting in two emission peaks at 450 and 560 nm, which can be ascribed to defects emission in SiO₂ and ZnO respectively. The mechanism of light emission from Mn²⁺, the effect of varying the concentration on the PL intensity, and the effect of annealing are discussed.     

Surface-dependent cytotoxicity on bacteria as a model for environmental stress of halloysite nanotubes

Nanoparticles of CoDy_0.1Fe_1.9O₄ were synthesized by sol–gel auto-combustion method. Four samples were synthesized from precursor solutions having different pH values in the range of 2.5–10. X-ray diffraction patterns were analyzed to determine the crystal phase of CoDy_0.1Fe_1.9O₄ nanoparticles synthesized at different pH. The XRD patterns confirm the formation of cubic spinel structure for CoDy_0.1Fe_1.9O₄ nanoparticles synthesized at different pH values. However the single phase is obtained only at pH 7.5, while γ and α-Fe₂O₃ phases appeared at pH 2.5, 5.0, and 10.0. Transmission electron microscopy shows that the structural morphology of the nanoparticles is highly dependent on the pH concentration. Particle size varies in between 24 and 36 nm with respect to change in pH concentration of the sample. Particle size increases to 36 nm with increase in pH up to 7.5 followed by a decrease in particle size for further increase in pH value. Magnetic properties were explored by vibrating sample magnetometry. The variation in pH during the synthesis process changes the size and structural morphology of the nanoparticles, which ultimately causes the variation in the values of the magnetic parameters such as saturation magnetization and coercivity. Infrared spectroscopy is employed to determine the local symmetry in the crystalline solids and to shed light on the ordering phenomenon under the influence of different pH values.     

The effect of cation distribution on magnetization of ZnFe2O4 nanoparticles

In this work zinc ferrite (ZnFe₂O₄) nanoparticles have been prepared by sol-gel method in two different media, one acidic and another one basic and then annealed at different temperatures from 350 to 800 °C. XRD investigations show that both samples have a single phase spinel structure. Mean crystallite sizes of the samples were calculated, using Scherrer’s formula, which are 13 and 16 nm for the samples prepared in acidic and basic media, respectively. The variation of cation distribution in the samples was estimated by the ratio of (2 2 0) and (2 2 2) intensity diffraction peaks and the results show that as-prepared nanoparticles have different ionic distributions in comparison with that of bulk zinc ferrite. Also the results show that by increasing annealing temperature the ionic distribution of the zinc ferrite nanoparticles tends to that of bulk sample. The magnetic properties of the samples were studied by VSM and the results show that zinc ferrite nanoparticles have a ferrimagnetic behavior. Also the morphology of the powders was examined by TEM.     

Strong green luminescence of Ni2+-doped ZnS nanocrystals

ZnS nanoparticles doped with Ni²⁺ have been obtained by chemical co-precipitation from homogeneous solutions of zinc and nickel salt compounds, with S^2- as precipitating anion, formed by decomposition of thioacetamide (TAA). The average size of particles doped with different mole ratios, estimated from the Debye–Scherrer formula, is about 2–2.5 nm. The nanoparticles could be doped with nickel during synthesis without altering the X-ray diffraction pattern. A Hitachi M-850 fluorescence spectrophotometer reveals the emission spectra of samples. The absorption spectra show that the excitation spectra of Ni-doped ZnS nanocrystallites are almost the same as those of pure ZnS nanocrystallites (λ_ex=308–310 nm). Because a Ni²⁺ luminescent center is formed in ZnS nanocrystallites, the photoluminescence intensity increases with the amount of ZnS nanoparticles doped with Ni²⁺. Stronger and stable green-light emission (520 nm) (its intensity is about two times that of pure ZnS nanoparticles) has been observed from ZnS nanoparticles doped with Ni²⁺. Received: 18 December 2000 / Accepted: 17 March 2001 / Published online: 20 June 2001     

Finite size effects on the structural and magnetic properties of sol–gel synthesized NiFe2O4 powders

Nanoparticles of nickel ferrite have been synthesized by the sol–gel method and the effect of grain size on its structural and magnetic properties have been studied in detail. X-ray diffraction (XRD) studies revealed that all the samples are single phasic possessing the inverse spinel structure. Grain size of the sol–gel synthesized powders has been determined from the XRD data and the strain graph. A grain size of 9 nm was observed for the as prepared powders of NiFe₂O₄ obtained through the sol–gel method. It was also observed that strain was induced during the firing process. Magnetization measurements have been carried out on all the samples prepared in the present series. It was found that the specific magnetization of the nanosized NiFe₂O₄ powders was lower than that of the corresponding coarse-grained counterparts and decreased with a decrease in grain size. The coercivity of the sol–gel synthesized NiFe₂O₄ nanoparticles attained a maximum value when the grain size was 15 nm and then decreased as the grain size was increased further.     

Effect of Particle Size and Phase Composition of Titanium Dioxide Nanoparticles on the Photocatalytic Properties

Titanium dioxide (TiO₂) nanoparticles were prepared by the oxidation of titanium tetrachloride (TiCl₄) in a diffusion flame reactor. The average diameter of particles was 15–30 nm and mass fraction of anatase ranged from 40% to 80%. Effects of particle size and phase composition of those TiO₂ nanoparticles on photocatalytic properties such as decomposition of methylene blue, bacteria and ammonia gas were investigated. The degree of decomposition of methylene blue by the TiO₂ nanoparticles under the illumination of the black light was directly proportional to the anatase mass fraction, but inversely to the particle size. The decomposition of bacteria and ammonia gas by the TiO₂ nanoparticles under the illumination of the fluorescent light showed the same trend as in the case of the methylene blue.     

Induction heating studies of magnetite nanospheres synthesized at room temperature for magnetic hyperthermia

An investigation of the synthesis of Fe₃O₄ nanopowders by the co-precipitation method is reported from aqueous and ethanol mediums. X-ray diffraction (XRD), transmission electron microscopy (TEM) and vibrating sample magnetometer are utilized to study the effect of variation of synthesis conditions on the crystal structure, crystallite size, microstructure and magnetic properties of the formed powders. The XRD analysis showed that the crystalline Fe₃O₄ phase was formed at Fe³⁺/Fe²⁺ molar ratio 2.0 prepared at room temperature for 1 h at pH 10. The crystallite size was in the range between 8 and 11 nm. TEM micrographs showed that the particles appeared as nanospheres. Superparamagnetic nanoparticles with low coercivity and remanence magnetization were achieved. Heating properties of the nanosphere samples in an alternating magnetic field at 160 KHz were evaluated. An excellent heating efficiency for the sample prepared in ethanol medium is a result of more relaxation losses occurring due to its small particle size.     

Photoluminescence properties of powder and pulsed laser-deposited PbS nanoparticles in SiO2

Thin films of lead sulfide (PbS) nanoparticles embedded in an amorphous silica (SiO₂) host were grown on Si(1 0 0) substrates at different temperatures by the pulsed laser deposition (PLD) technique. Surface morphology and photoluminescence (PL) properties of samples were analyzed with scanning electron microscopy (SEM) and a 458 nm Ar⁺ laser, respectively. The PL data show a blue-shift from the normal emission at ∼3200 nm in PbS bulk to ∼560-700 nm in nanoparticulate PbS powders and thin films. Furthermore, the PL emission of the films was red-shifted from that of the powders at ∼560 to ∼660 nm. The blue-shifting of the emission wavelengths from 3200 to ∼560-700 nm is attributed to quantum confinement of charge carriers in the restricted volume of nanoparticles, while the red-shift between powders and thin-film PbS nanoparticles is speculated to be due to an increase in the defect concentration. The red-shift increased slightly with an increase in deposition temperature, which suggests that there has been a relative growth in particle sizes during the PLD of the films at higher temperatures. Generally, the PL emission of the powders was more intense than that of the films, although the intensity of some of the films was improved marginally by post-deposition annealing at 400 °C. This paper compares the PL properties of powder and pulsed laser-deposited thin films of PbS nanoparticles and the effects of deposition temperatures.     

The structure and magnetic properties of Zn1−xNixFe2O4 ferrite nanoparticles prepared by sol–gel auto-combustion

Zn_1−xNi_xFe₂O₄ ferrite nanoparticles were prepared by sol–gel auto-combustion and then annealed at 700 °C for 4 h. The results of differential thermal analysis indicate that the thermal decomposition temperature is about 210 °C and Ni–Zn ferrite nanoparticles could be synthesized in the self-propagating combustion process. The microstructure and magnetic properties were investigated by means of X-ray diffraction, scanning electron microscope, and Vibrating sample magnetometer. It is observed that all the spherical nanoparticles with an average grain size of about 35 nm are of pure spinel cubic structure. The crystal lattice constant declines gradually with increasing x from 0.8435 nm (x=0.20) to 0.8352 nm (x=1.00). Different from the composition of Zn_0.5Ni_0.5Fe₂O₄ for the bulk, the maximum M_s is found in the composition of Zn_0.3Ni_0.7Fe₂O₄ for nanoparticles. The H_c of samples is much larger than the bulk ferrites and increases with the enlarging x. The results of Zn_0.3Ni_0.7Fe₂O₄ annealed at different temperatures indicate that the maximum M_s (83.2 emu/g) appears in the sample annealed at 900 °C. The H_c of Zn_0.3Ni_0.7Fe₂O₄ firstly increases slightly as the grain size increases, and presents a maximum value of 115 Oe when the grains grow up to about 30 nm, and then declines rapidly with the grains further growing. The critical diameter (under the critical diameter, the grain is of single domain) of Zn_0.3Ni_0.7Fe₂O₄ nanoparticles is found to be about 30 nm.     

Optical and ESR studies on Fe doped ZnS nanocrystals

Zn_1 − xFe_xS (x=0.0, 0.1, 0.2, 0.4 and 0.6) nanocrystals have been obtained by chemical co-precipitation from homogeneous solutions of zinc and iron salt compounds, with S²⁻ as precipitating anion formed by decomposition of thiophenol. The TEM micrographs show a spherical shape for ZnS nanocrystals and their average size is around 7 nm. The optical absorption spectra indicate a blue shift of the absorption edge with increasing Fe-content. The luminescence of nanoparticles excite at about 370 nm with an emission peak at around 490 nm. At room temperature, ESR signal characteristic of Fe³⁺ was observed in samples of all concentrations.     

Magnetic properties of core-shell catalyst nanoparticles for carbon nanotube growth

Two types of core-shell nanoparticles have been prepared by laser pyrolysis using Fe(CO)₅ and C₂H₂ or [(CH₃)₃Si]₂O as precursors and C₂H₄ as sensitizer. The first type (about 4 nm diameter) - produced by the decomposition of Fe(CO)₅ in the presence of C₂H₄ and C₂H₂ - consists of Fe cores protected by graphenic layers. The second type (mean particle size of about 14 nm) consists also of Fe cores, yet covered by few nm thick γ-Fe₂O₃/porous polycarbosiloxane shells resulted from the [(CH₃)₃Si]₂O decomposition and superficial oxidation after air exposure. The hysteresis loops suggest a room temperature superparamagnetic behavior of the Fe-C nanopowder and a weak ferromagnetic one for larger particles in the Fe-Fe₂O₃-polymer sample. Both types of nanoparticles were finally used as a catalyst for the carbon nanotube growth by seeding Si(100) substrates via drop-casting method. CNTs were grown by Hot-Filament Direct.Current PE CVD technique from C₂H₂ and H₂ at 980 K. It is suggested that the increased density and orientation degree observed for the multiwall nanotubes grown from Fe-Fe₂O₃-polymer nanoparticles could be due to their magnetic behavior and surface composition.     

Synthesis,characterization and magnetic properties of MFe2O4 (M=Co,Mg, Mn,Ni) nanoparticles using ricin oil as capping agent

We focused on obtaining MFe₂O₄ nanoparticles using ricin oil solution as surfactant and on their structural characterization and magnetic properties. The annealed samples at 500 °C in air for 6 h were analyzed for the crystal phase identification by powder X-ray diffraction using CuKα radiation. The particle size, the chemical composition and the morphology of the calcinated powders were characterized by scanning electron microscopy. All sintered samples contain only one phase, which has a cubic structure with crystallite sizes of 12–21 nm. From the infrared spectra of all samples were observed two strong bands around 600 and 400 cm⁻¹, which correspond to the intrinsic lattice vibrations of octahedral and tetrahedral sites of the spinel structure, respectively, and characteristic vibration for capping agent. The magnetic properties of fine powders were investigated at room temperature by using a vibrating sample magnetometer. The room temperature M–H hysteresis loops show ferromagnetic behavior of the calcined samples, with specific saturation magnetization (M_s) values ranging between 11 and 53 emu/g.     

The colloidal stability and core-shell structure of magnetite nanoparticles coated with alginate

The adsorption of alginate (Alg) onto the surface of in water dispersed Fe₃O₄ nanoparticles and zeta potential of alginate-coated Fe₃O₄ nanoparticles have been investigated to optimize the colloidal stability of Alg-coated Fe₃O₄ nanoparticles. The adsorption amount of Alg increased with the decrease of adsorption pH. The zeta potential of Fe₃O₄ nanoparticles shifted to a lower value after adsorption of Alg. The lower adsorption pH was the lower zeta potential of Fe₃O₄ nanoparticles became. The Alg-coated Fe₃O₄ nanoparticles were found to be stabilized by steric and electrostatic repulsions. Those prepared at pH 6 were not stable around pH 5, and those prepared at pH 4 became unstable at pH below 3.5. Alg of M_w 45 kDa was a little bit more adsorbed onto nanoparticles surface than that of M_w 24 kDa. An average Fe₃O₄ core size of 9.3 ± 1.7 nm was found by transmission electronic microscopy. An average hydrodynamic diameter of 30-150 nm was measured by photon correlation spectroscopy. However, an average core size of 10 nm and an average hydrodynamic diameter of 38 nm were estimated from the magnetization curve of the concentrated magnetic fluids (MFs). The maximum available saturation magnetization of MFs was about 3.5 kA/m.     

Anisotropic gold nanoparticles and gold plates biosynthesis using alfalfa extracts

Industrial and medical applications for gold nanoparticles are extensive, yet highly dependent on their chemical and structural properties. Thus, harnessing the size and shape of nanoparticles plays an important role in nanoscience and nanotechnology. Anisotropic polyhedra and nanoplates were biosynthesized via reduction of 3 mM AuCl₄ ⁻ solution at room temperature. Alfalfa biomass extracts prepared in water and in isopropanol separately were used as reducing agents at pH 3.5 and 3.0, respectively. Nanoparticles observed in the isopropanol extract presented a size range of 30–60 nm, and the morphologies present included 30 nm decahedra and 15 nm icosahedra. Gold nanoplates produced in the water extract were mainly triangular, ranging from 500 nm to 4 μm in size. The resulting nanoparticles and nanoplates can be potentially used in the study of their unique physical properties and for the mechanisms of formation using alfalfa biomass extracts.     

Correlation between structural and magnetic properties of substituted (Cd,Zr) cobalt ferrite nanoparticles

This work correlates the magnetic properties to the microstructure of the calcined nanocrystalline Cd_xCo_1-xZr_0.05Fe_1.95O₄ (0.0 ≤ x ≤ 0.3 in a step of 0.05) powders produced by Pechini sol–gel method. The dry gel was grinded and calcined at 700 °C in a static air atmosphere for 1 h. The thermal decomposition process of dried gel was studied by thermo gravimetric analysis (TGA) combined with differential analysis (DTA). Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM) and vibrating sample magnetometer (VSM) were carried out to investigate the structural bonds identification, crystallographic properties, morphology and magnetic properties of the obtained powders. The XRD pattern of the samples showed that the synthesized materials were of a single cubic phase with the nanocrystalline Co–Zr–Cd ferrite which had an average crystallite size of 32–40 nm and particle size of 55 nm resulted from FE-SEM. The magnetic properties were measured from the hysteresis loops. The magnetic measurements had indicated that the coercivity and the magnetization decreased by increasing the Cd content.     

Synthesis and luminescence properties of nanocrystalline Gd2O3:Eu by combustion process

The nanocrystalline Gd₂O₃:Eu³⁺ powders with cubic phase were prepared by a combustion method in the presence of urea and glycol. The effects of the annealing temperature on the crystallization and luminescence properties were studied. The results of XRD show pure phase can be obtained, the average crystallite size could be calculated as 7, 8, 15, and 23 nm for the precursor and samples annealed at 600, 700 and 800 °C, respectively, which coincided with the results from TEM images. The emission intensity, host absorption and charge transfer band intensity increased with increasing the temperature. The slightly broad emission peak at 610 nm for smaller particles can be observed. The ratio of host absorption to O²⁻-Eu³⁺ charge transfer band of smaller nanoparticles is much stronger compared with that for larger nanoparticles, furthermore, the luminescence lifetimes of nanoparticles increased with increasing particles size. The effects of doping concentration of Eu³⁺ on luminescence lifetimes and intensities were also discussed. The samples exhibited a higher quenching concentration of Eu³⁺, and luminescence lifetimes of nanoparticles are related to annealing temperature of samples and the doping concentration of Eu³⁺ ions.     

Effect of the temperature on the synthesis of (K,Na)NbO<Subscript>3</Subscript>-modified nanoparticles by a solid state reaction route

(Na_0.5K_0.5)NbO₃ (KNN)-modified nano-particulated powders, based on variations of sodium–potassium niobate, were synthesised by solid state reaction from carbonate starting materials. The nanoparticles were attained by an optimization of the raw materials particle size and particle refinement of the carbonates during their decomposition. Particle sizes between 50 and 200 nm have been obtained as a function of calcination (decomposition) temperature. The obtained powders showed a co-existence between a tetragonal phase and an orthorhombic phase. The optimization of the raw materials particle size and the particle refinement of the carbonates during their decomposition play a key role in the formation of the KNN-modified nano particles. The developed method is well suited for the production of KNN-modified nano powders at low cost for mass production.     

Novel NdCo<Subscript>5</Subscript> nanoflakes and nanoparticles produced by surfactant-assisted high-energy ball milling

High-energy ball milling has been shown to be a promising method for the fabrication of rare earth—transition metal nanopowders. In this work, NdCo₅ nanoflakes and nanoparticles have been produced by a two-stage high-energy ball milling (HEBM), by first using wet HEBM to prepare precursor nanocrystalline powders followed by surfactant-assisted HEBM. NdCo₅ flakes have a thickness below 150 nm and an aspect ratio as high as 10²–10³; the nanoparticles have an average size of 7 nm. Both the nanoparticles and nano-flakes exhibited high coercivities at low temperatures, with values at 50 K of 3 and 3.7 kOe, respectively. The high values of coercivity can be attributed to the large surface anisotropy of nanoparticles that leads to an effective uniaxial-type of behavior in contrast to the planar anisotropy of the bulk samples. Angle-dependent magnetization measurements at different temperatures were used to determine the spin reorientation transitions in the nanopowders and nanoparticles. The nanoparticles showed spin reorientation temperatures, T _SR1 = 276 and T _SR2 = 237 K which are lower when compared with the values of 290 and 245 K, respectively for bulk.     

Nanoscale assembly of amine-functionalized colloidal iron oxide

We demonstrate a single-step facile approach for highly water-stable assembly of amine-functionalized Fe₃O₄ nanoparticles using thermal decomposition of Fe-chloride precursors in ethylene glycol medium in the presence of ethylenediamine. The average size of nanoassemblies is 40±1 nm, wherein the individual nanoparticles are about 6 nm. Amine-functionalized properties are evident from Fourier transform infrared spectrometer (FTIR), thermal and elemental analyses. The saturation magnetization and spin-echo r₂ of the nanoassemblies were measured to be 64.3 emu/g and 314.6 mM⁻¹ s⁻¹, respectively. The higher value of relaxivity ratio (r₂/r₁=143) indicates that nanoassemblies are a promising high-efficiency T2 contrast agent platform.