Zigzag型石墨纳米带电子结构和输运性质的第一性原理研究

采用第一性原理电子结构和输运性质计算研究了zigzag型单层石墨纳米带(具有armchair 边缘)的电子结构和输运性质及其边缘空位缺陷效应. 研究发现,完整边缘的zigzag型石墨纳米带是具有一定能隙的半导体带,边缘空位缺陷的存在使得纳米带能隙变小,且缺陷浓度越大,能隙越小,并发生了半导体-金属转变. 利用这些研究结果,将有助于在能带工程中实现其电子结构裁剪. 关键词： 石墨纳米带 空位缺陷 电子结构 输运性质     

双空位缺陷石墨纳米带的电子结构和输运性质研究

基于第一原理电子结构和输运性质计算,研究了585双空位拓扑缺陷对锯齿（zigzag）型石墨纳米带（具有椅型（armchair）边）电子结构和输运性质的影响.研究发现,585双空位缺陷的存在使得锯齿型石墨纳米带的能隙增大,并在能隙中出现了一条局域于缺陷处的缺陷态能带,双空位缺陷的取向也影响其能带结构.另外,585双空位缺陷对能隙较小的锯齿型石墨纳米带输运性质的影响较大,而对能隙较大的锯齿型石墨纳米带影响很小,缺陷取向并不显著影响纳米带的输运性质. 关键词： 石墨纳米带 585空位缺陷 电子结构 输运性质     

单空位缺陷对石墨纳米带电子结构和输运性质的影响

基于第一性原理电子结构和输运性质计算,研究了单空位缺陷对单层石墨纳米带(包括zigzag型和armchair型带)电子性质的影响.研究发现,单空位缺陷使石墨纳米带在费米面上出现一平直的缺陷态能带;单空位缺陷的引入使zigzag型半导体性的石墨纳米带变为金属性,这在能带工程中有重要的应用价值;奇数宽度的armchair型石墨纳米带表现出金属特性,有着很好的导电性能,同时,偶数宽度的armchair型石墨带虽有金属性的能带结构,但却有类似半导体的伏安特性;单空位缺陷使得奇数宽度的armchair石墨纳米带导电 关键词： 石墨纳米带 单空位缺陷 电子结构 输运性质     

扶手椅型石墨纳米带的双空位缺陷效应研究

采用基于密度泛函理论的第一性原理电子结构和输运性质计算,研究了扶手椅型石墨纳米带（具有锯齿边缘）的双空位缺陷效应.研究发现：双空位缺陷的存在并没有改变石墨纳米带的金属特性,但改变了费米面附近的能带结构.同时,双空位缺陷的取向对石墨纳米带的输运性质有很重要的影响.对于奇数宽度的纳米带,斜向双空位缺陷使得石墨带导电性能减弱,而垂直双空位能基本保留原有的线性伏安特性,导电性能降低较少;对于偶数宽度的纳米带,斜向双空位缺陷会使石墨带导电性能明显增强,而垂直双空位缺陷则具有完整石墨带的输运性质. 关键词： 石墨纳米带 585双空位缺陷 电子结构 输运性质     

氢化与非氢化石墨烯纳米条带的密度泛函研究

基于密度泛函理论的第一性原理计算方法,研究了宽度N=8的边缘氢化和非氢化条带的结构和电子性质. 研究表明,扶手形无氢化石墨纳米条带的边缘碳原子是以三重键相互结合,它在边缘的成键强度比氢化时要高,具有更强的化学活性,可作为纳米化学传感器的基础材料. 能带结构计算表明,无论是扶手形条带还是锯齿形条带,它们都是具有带隙的半导体,且无氢化条带的带隙要比氢化的条带带隙宽度大,氢化对于条带的电子性质具有显著修饰作用. 通过锯齿形石墨纳米条带顺磁性、铁磁性和反铁磁性的计算,发现反铁磁的状态最稳定,并且边缘磁性最强,这有利于条带在自旋电子器件中的应用. 关键词： 石墨纳米条带 成键机理 电子结构 自旋分布     

纤铁矿型TiO_2纳米片层结构的稳定性与电子结构研究

采用平面波超软赝势方法研究了纤铁矿型TiO_2纳米片层结构的稳定性和电子结构.结果显示该结构具有较高的稳定性,其带隙比锐钛矿型TiO_2要大0.59 e V,带隙内没有出现表面态.通过对空位缺陷形成能的比较,结果显示这在还原性气氛下纤铁矿型TiO_2纳米片层表面Ti空位的形成能明显低于O空位的形成能,确定出最容易出现的缺陷是-4价的Ti空位,该空位缺陷的出现会使带隙中产生表面缺陷态.与体相内缺陷不同,表面缺陷态可以促进电子和空穴的分离,这些发现可以合理的解释最近的实验结果 .     

闪锌矿结构AlSb空位缺陷性质的第一性原理研究

采用基于密度泛函理论(DFT)第一性原理的平面波超软赝势方法，计算含有锑空位和铝空位的电子结构，发现空位引起周围原子弛豫，晶体结构发生畸变。在此基础上研究了空位缺陷对闪锌矿型AlSb体系电子结构的影响，结果表明，铝空位缺陷使锑化铝费米能级降低，带隙变窄；而锑空位缺陷则使锑化铝费米能级升高，带隙变窄，同时，锑化铝的半导体类型由p型变为n型。对光学性质的研究发现，由于空位的引入使其邻近原子电子结构发生变化，使得空位缺陷系统光学性质的变化主要集中在低能量区域。     

闪锌矿结构AlSb空位缺陷性质的第一性原理研究

采用基于密度泛函理论(DFT)第一性原理的平面波超软赝势方法,计算含有锑空位和铝空位的AlSb电子结构,发现空位引起周围原子弛豫,晶体结构发生畸变.在此基础上研究了空位缺陷对闪锌矿型AlSb体系电子结构的影响,结果表明,铝空位缺陷使锑化铝费米能级降低,带隙变窄;而锑空位缺陷则使锑化铝费米能级升高,带隙变窄,同时,锑化铝的半导体类型由p型变为n型.对光学性质的研究发现,由于空位的引入使其邻近原子电子结构发生变化,使得空位缺陷系统光学性质的变化主要集中在低能量区域.     

边缘重构对锯齿型石墨烯纳米带电子输运的影响

实验研究表明石墨烯纳米带中广泛地存在边缘结构重构且稳定的边缘缺陷结构.本文采用第一性原理的计算方法研究了锯齿型石墨烯纳米带中边缘结构重构形成的两种不同缺陷结构对材料电子输运性能的影响.研究发现两种缺陷边缘结构对稳定纳米尺度位型结构和电子能带结构具有显著影响,它使得费米能级发生移动并引起了共振背散射.两种边缘缺陷重构均抑制了费米能级附近电子输运特性并导致不同区域的电子完全共振背散射,电导的抑制不仅与边缘缺陷结构的大小有关,它更取决于边缘缺陷重构位型引起的缺陷态的具体分布和电子能带的移动.     

堆叠石墨片对锯齿型石墨纳米带电子输运的影响

采用格林函数方法研究了堆叠石墨片对锯齿型石墨纳米带电子输运性质的影响,计算了两种不同堆叠方式下锯齿型石墨纳米带的电导.研究发现,由于堆叠石墨片与石墨纳米带的耦合作用,锯齿型石墨纳米带的电导谱出现了电导谷.在远离费米能处,两种堆叠方式下的电导谷位置相近甚至重合;而在费米能附近,两种堆叠方式下的电导谷存在差异.此外,讨论了堆叠石墨片的几何尺寸对锯齿型石墨纳米带电子输运的影响.结果显示,随石墨片几何尺寸的增大,锯齿型石墨纳米带在两种堆叠方式下远离费米能处的电导谷逐渐向费米能方向移动,同时其费米能附近的电导谷在两种堆叠方式下的差异随石墨片尺寸的增大变得更为明显.研究结果表明,堆叠石墨片能够有效地调制锯齿型石墨纳米带的电子输运性质.     

Atomic and electronic structures of divacancy in graphene nanoribbons

First principles calculations have been performed to investigate the electronic structures and transport properties of defective graphene nanoribbons (GNRs) in the presence of pentagon-octagon-pentagon (5-8-5) defects. Electronic band structure results reveal that 5-8-5 defects in the defective zigzag graphene nanoribbon (ZGNR) is unfavorable for electronic transport. However, such defects in the defective armchair graphene nanoribbon (AGNR) give rise to smaller band gap than that in the pristine AGNR, and eventually results in semiconductor to metal-like transition. The distinct roles of 5-8-5 defects in two kinds of edged-GNR are attributed to the different coupling between π^? and π subbands influenced by the defects. Our findings indicate the possibility of a new route to improve the electronic transport properties of graphene nanoribbons via tailoring the atomic structures by ion irradiation.     

High thermoelectric performance of one graphene nanoribbon with line defects

We investigate the quantum transport through zigzag graphene nanoribbons with embedded “5-7-5”-edge line defects, by means of the non-equilibrium Green's function technique. It is found that when two semi-infinite line defects exist in the nanoribbon, notable Fano antiresonance takes place in the quantum transport process, which enables to drive the apparent thermoelectric effect. We propose this structure to be a promising candidate for improving the thermoelectric efficiency based on graphene nanoribbons.     

Ab initio study of the electronic and transport properties of waved graphene nanoribbons

We apply the nonequilibrium Green's function method based on density functional theory to investigate the electronic and transport properties of waved zigzag and armchair graphene nanoribbons. Our calculations show that out-of-plane mechanical deformations have a strong influence on the band structures and transport characteristics of graphene nanoribbons. The computed I-V curves demonstrate that the electrical conductance of graphene nanoribbons is significantly affected by deformations. The relationship between the conductance and the compression ratio is found to be sensitive to the type of the nanoribbon. The results of our study indicate the possibility of mechanical control of the electronic and transport properties of graphene nanoribbons.     

The importance of defects for carbon nanoribbon based electronics

The utilization of graphene nanoribbons for next generation nanoelectronics is commonly expected to depend on the controlled synthesis that yields a low density of defects. Edge roughness and vacancies have been shown to have a large impact on the performance of graphene nanoribbon transistors. In contrast, we show how certain defects can be used to enhance the electronic and magnetic properties of graphene nanoribbons. We explore the properties of hybrid graphene nanoribbons with armchair and zigzag features joined by an array of pentagon–heptagon structural defects. The graphene nanoribbons display an increased density of states at the Fermi level, and half metallicity in absence of external fields. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Edge reconstruction limited electron transport of zigzag graphene nanoribbon

Recent experimental characterizations have clearly visualized edge reconstructions in graphene nanoribbon and stable defective configurations. We have performed first principles calculations to evaluate the effects of atomic edge arrangement on the electronic transport properties of zigzag graphene nanoribbons (ZGNR). It is found that different conductance behaviors and variation of resonant energies are influenced by atomic reconstruction among three defective edge configurations. It is predicted that the conductance in edge reconstructed ZGNR is not a monotonic function of the increasing concentration of defects in size, but the topology and the distribution of defects should be taken into account. Our findings suggest that the ability of tuning the electronic transport of ZGNR could be improved through edge reconstruction activated by energetic particle irradiation.     

Electronic transport through zigzag/armchair graphene nanoribbon heterojunctions

The electronic transport properties of a graphene nanoribbon (GNR) are known to be sensitive to its width, edges and defects. We investigate the electronic transport properties of a graphene nanoribbon heterojunction constructed by fusing a zigzag and an armchair graphene nanoribbon (zGNR/aGNR) side by side. First principles results reveal that the heterojunction can be either metallic or semiconducting, depending on the width of the nanoribbons. Intrinsic rectification behaviors have been observed, which are largely sensitive to the connection length between the zGNR and aGNR. The microscopic origins of the rectification behavior have been revealed. We find that the carrier type can alter from electrons to holes with the bias voltage changing from negative to positive; the asymmetrical transmission spectra of electrons and holes induced by the interface defects directly results in the rectification behavior. The results suggest that any methods which can enhance the asymmetry of the transmission spectra between holes and electrons could be used to improve the rectification behavior in the zGNR/aGNR heterojunction. Our findings could be useful for designing graphene based electronic devices.