基于4，8-二氢二呋咱[3，}4-b，e]吡嗪高能材料的设计与筛选

为了寻找高能量密度的材料,本文设计了一系列基于4,8-二氢二呋咱[3,4-b,e]吡嗪的含能材料. 利用密度泛函理论研究了它们结构与性质之间的关系. 结果表明,这些设计化合物的性质受到含能基团和杂环取代基的影响. -N₃含能基团是提高设计化合物生成热的最有效取代官能团,而四唑环/-C(NO₂)₃基团对炸药的爆轰性能有较大贡献. 键解离能分析表明,引入-NHNH₂,-NHNO₂,-CH(NO₂)₃和-C(NO₂)₃基团会显著降低键解离能. 由于化合物A8,B8,C8,D8,E8和F8具有良好的爆轰性能和热稳定性,最终被筛选为潜在的高能密度材料. 此外,还计算了这些筛选化合物的电子结构.     

双(2,2-二硝基丙基)甲缩醛的结构和爆轰性能的量子化学研究

利用B3LYP/6-311+G(2d,p)方法对一种新型含能增塑剂双(2,2-二硝基丙基)甲缩醛进行几何优化,计算了其红外光谱、生成焓和爆轰特性. 分析了最弱键的键离解能和键级并预测了目标化合物的热稳定性. 结果表明双(2,2-二硝基丙基)甲缩醛中的四个N-NO₂键的键离解能都为164.38 kJ/mol. 表明目标化合物是一个热力学性能稳定的化合物. 以凝聚相生成焓和分子密度为基础,采用Kamlet-Jacobs方法预测其爆速和爆压. 目标化合物的晶体结构属于P21空间群.     

氧化石墨烯负载的Pt单原子催化硼胺烷水解机理的理论研究

本文研究了氧化石墨烯负载Pt单原子(Pt₁/Gr-O)催化硼胺烷(NH₃BH₃)全水解反应机理,即一分子的NH₃BH₃生成三分子的氢气(H₂)的过程. 在水解路径中,首先吸附的硼胺烷连续断裂两个B-H键生成第一分子的H₂. 接着,一个H₂O分子与^*BHNH₃基团(^*表示吸附态)反应生成^*BH(H₂O)NH₃,其中伸长的O-H键断裂后形成^*BH(OH)NH₃. 然后,第二个H₂O与^*BH(OH)NH₃反应生成^*BH(OH)(H₂O)NH₃,在指向Pt₁/Gr-O表面的O-H断裂后,生成BH(OH)₂NH₃并脱附到水溶液中. 两个水分子脱氢产生的两个H原子脱附生成第二个H₂分子,且Pt₁/Gr-O催化剂恢复. 脱附后的BH(OH)₂NH₃在水溶液中水解生成第三个H₂分子. 纵观整个水解反应,H₂O分子和^*BHNH₃基团的结合是反应速控步,其反应能垒是16.1 kcal/mol. 因此,Pt₁/Gr-O有希望成为室温催化NH₃BH₃全水解催化剂.     

C-I键均裂解离焓的密度泛函理论研究

在高级别理论(包含使用外推基组的MP2和CCSD(T))方法及大量密度泛函方法的理论基础上, 研究了不同种类有机碘化物的C-I键均裂解离能. 密度泛函方法的系统性评估计算结果表明,MPWLYP1M方法的计算精度最高. 运用该方法系统地考查了C(sp³)-I和C(sp²)-I键的取代基效应. 以及取代碘苯及取代苄基碘化物的远程取代基效应. 此外,在MPWLYP1M方法的基础上研究了典型五元及六元芳香杂环碘化物的C-I键解离焓值.     

[Ru(MeIm)4L]2+ (L=iip, tip, 2ntz)的电子结构、DNA-键合、构效关系及光谱特征

采用密度泛函的方法,结合导体极化连续模型研究了水溶性二价钌-甲基咪唑类配合物[Ru(MeIm)₄iip]²⁺ (1)、[Ru(MeIm)₄tip]²⁺(2)和[Ru(MeIm)₄2ntz]²⁺ (3)的电子结构、DNA的键合倾向及构效关系．在水溶液中几何优化的基础上分析了配合物的电子结构特征,并合理解释了配合物与DNA的键合倾向．计算结果表明,在主配体上用噻吩代替咪唑取代基可以有效提高配合物与DNA的键合力;同时,在主配体的骨架上引入强电负性的N原子及NO₂基团可以明显降低配合物最低未占据分子轨道能量及前沿分子轨道能量差．基于以上计算结果,预测所设计的配合物3具有最大的DNA键合力常数．另外,详细分析了配合物1、2的构效关系及抗肿瘤作用机理,并预测了配合物3的抗肿瘤活性．最后,用含时密度泛函方法对配合物的电子吸收光谱进行了计算和模拟,并与实验结果进行了对比分析.     

密度泛函理论方法研究6H-SiC(0001)表面对氧分子和水分子的吸附

本文通过密度泛函方法计算6H-SiC(0001)表面对氧分子和水分子的吸附. 在6H-SiC(0001)表面上吸附的O₂分子自发地解离成O^*,并被吸收在C与Si原子之间的空位上. 吸附的H₂O自发地分解成OH^*和H^*,它们都被吸附在Si原子的顶部,OH^*进一步可逆地转化为O^*和H^*. H^*可以使Si悬键饱和并改变O^*的吸附类型,并进一步稳定6H-SiC(0001)表面并防止其转变为SiO₂.     

取代基效应对对称共价有机框架光催化性质的影响

对称共价有机框架(COF)光催化剂通常存在电荷分离效率低和光激发态寿命短的问题. 通过密度泛函理论和含时密度泛函理论计算,本文发现了用一个或两个取代基(N或NH₂)在具有代表性的对称共价有机框架(N₀-COF)的连接单元内进行部分取代可得到具有电荷分离特征的共价有机框架(N₁-COF、N₂-COF、(NH₂)₁-N₀-COF和(NH₂)₂-N₀-COF). 此外,还发现N₀-COF的最高占据晶体轨道和最低未占据晶体轨道的能级位置可通过取代远离或靠近真空能级,这取决于取代基的吸电子或给电子特性. 因此,本文提出了通过精心选择具有吸电子或给电子效应的取代基,并在对称共价有机框架的连接单元内进行部分取代,所获得的共价有机框架可具有高效的电荷分离以及驱动特定光催化反应的合适最高占据晶体轨道和最低未占据晶体轨道能级位置. 该规则可用于进一步提升许多具有对称性的共价有机框架的光催化性能.     

F−(H2O)+CH3I配体交换反应动力学

本文介绍F^?(H₂O)+CH₃I→[FCH₃I]^?+H₂O在交叉分子束碰撞能量0.3∽2.6 eV的配体交换动力学成像结果. 产物的动能受到弱键结合配合物的稳定性的影响，大量水分子的内部激发不利于中间物有效的能量重新分配，随着碰撞增加，低动能受到抑制. 在0.3 eV时，内部亲核取代非常重要，为形成I^?和I^?(H₂O)的竞争性亲核取代途径提供了依据.     

Eu2+, Cr3+共掺杂的MAl12O19 (M=Ca, Sr, Ba) 的发光性质及能量传递

三基色荧光粉中, 红色荧光粉性能较差, 为获得性能优良的红色荧光粉, 本文采用高温固相法合成了Eu²⁺, Cr³⁺单掺杂及共掺杂的碱土金属多铝酸盐MAl₁₂O₁₉ (M =Ca, Sr, Ba) 发光体. 实验表明, 在以上三种基质中均存在Eu²⁺→Cr³⁺的能量传递, 利用能量传递可以有效将Eu²⁺的蓝光或绿光转换为红光. 三种碱土金属多铝酸盐基质的晶体结构相似,但Eu²⁺, Cr³⁺发光受晶体场影响,导致在不同的基质中Eu²⁺, Cr³⁺间能量传递效率不同.通过光谱分析及能量传递效率计算发现, 相同掺杂浓度下,CaAl₁₂O₁₉中Eu²⁺→Cr³⁺的能量传递效率最高,SrAl₁₂O₁₉次之, BaAl₁₂O₁₉最低.红光转换率在CaAl₁₂O₁₉中最高.     

GPCR A2AAR腺苷受体蛋白的激动剂结合及其诱导的蛋白活性开关构象变化

运用分子动力学模拟,研究了腺苷酸(激动剂)与A_2AAR腺苷受体蛋白的相互作用和配体结合诱导的蛋白动力学变化.识别了与腺苷酸结合力强于0.5 kcal/mol的关键基团：A63^2.61,I66^2.64, V84^3.32, L85^3.33, T88^3.36, F168^5.29, M177^5.38, L249^6.51     

DFT studies on a high-energy density cage compound 1, 3, 5, 7, 9, 11-hexo(N(CH3)NO2)-2, 4, 6, 8, 10, 12-hexaazatetracyclo[5, 5, 0, 0, 0] dodecane

The infrared and Raman spectra, heat of formation (HOF) and thermodynamic properties were investigated by B3LYP/6-31G^** method for a new designed polynitro cage compound 1,3,5,7,9,11-hexo(N(CH₃)NO₂)-2,4,6,8,10,12-hexaazatetracyclo[5,5,0,0,0]dodecane. The detonation velocity (D) and pressure (P) were predicted by the Kamlet–Jacobs equations based on the theoretical density and condensed HOF. The bond dissociation energies and bond orders for the weakest bonds were analysed to investigate the thermal stability of the title compound. The computational result shows that the detonation velocity and pressure of the title compound are superior to those of hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), but inferior to those of 1,3,5,7-tetranitro-1,3,5,7-tetraazacyclooctane (HMX) and hexanitrohexaazaisowurtzitane (HNIW). And the analysis of thermal stability shows that the first step of pyrolysis is the rupture of the N₇–NO₂ bond. The crystal structure obtained by molecular mechanics belongs to the P2₁ space group, with the lattice parameters Z = 2, a = 11.8246 Å, b = 10.4632 Å, c = 15.9713 Å, ρ = 1.98 g cm^?3.     

不同含能取代基和桥基对碳桥联四唑-2-氮氧化物的性能影响密度泛函理论研究

Based on the parent tetrazole 2N-oxide, six series of novel carbon-linked ditetrazole 2N-oxides with different energetic substituent groups (-NH₂, -N₃, -NO₂, NF₂, -NHNO₂) and energetic bridge groups (-CH₂-, -CH₂-CH₂-, -NH-, -N=N-, -NH-NH-) were designed. The overall performance and the effects of different energetic substituent groups and energetic bridge groups on the performance were investigated by density functional theory and electrostatic potential methods. The results showed that most of designed compounds have oxygen balance around zero, high heats of formation, high density, high energy, and acceptable sensitivity, indicating that tetrazole N-oxide is a useful parent energetic compound employed for obtaining high energy compounds, even only combined with some very common energetic substituent groups and bridge groups. Comprehensively considering the effects on energy and sensitivity, the -NO₂, -NF₂, -NH-and -NH-NH-are appropriate substituent groups for combining tetrozale N-oxide to design new energetic compounds, while -NH₂, -N₃, -CH₂-CH₂-, and -N=N-are inappropriate.     

Theoretical studies on nitrogen‐rich furoxan‐based heterocyclic derivatives

The density functional theory method was used to study the heats of formation (HOFs), energetic properties, electronic structure of a series of 4,4″‐dinitro(3,3′:4′,3′′)tris([1,2,5]oxadiazole)‐2′‐oxide (3,4‐bis[4′‐nitrofurazan‐3′‐yl]furoxan) derivatives. The results show that the substitution of the nitro group is very useful for improving their HOFs and detonation performances. The HOFs of the title compounds are all positive and larger than those of 1,3,5‐trinitro‐1,3,5‐triazinane and 1,3,5,7‐tetranitro‐1,3,5,7‐tetrazocane. The analysis of oxygen balance shows that the studied compounds need the oxygen in the explosive. Compound A1 has larger detonation velocity and detonation pressure than those of 1,3,5,7‐tetranitro‐1,3,5,7‐tetrazocane and can be regarded as a potential candidate for high‐energy compounds because of the moderate heat of detonation, high density, and high N. In addition, the energy gaps between the highest occupied molecular orbital and lowest unoccupied molecular orbital of the studied compounds are further investigated.     

Theoretical studies on 2‐(5‐amino‐3‐nitro‐1,2,4‐triazolyl)‐3,5‐dinitropyridine (PRAN) and its derivatives

In this work, a set of derivatives of 2‐(5‐amino‐3‐nitro‐1,2,4‐triazolyl)‐3,5‐dinitropyridine (PRAN) with different energetic substituents (?N₃, –NO₂, –NH₂, –NF₂) have been studied at the Becke, three‐parameter, Lee–Yang–Parr/aug‐cc‐pvdz, Becke, three‐parameter, Lee–Yang–Parr/6‐31G(d), Becke, three‐parameter, Perdew 86/6‐31G(d), and Becke three‐parameter, Perdew–Wang 91/6‐31G(d,p) levels of density functional theory. The gas‐phase heats of formation were predicted with isodesmic reactions and the condensed‐phase HOFs were estimated with the Politzer approach. The effects of different functionals and basis sets were analyzed. –N₃ and –NO₂ greatly increase while –NH₂ and –NF₂ slightly decrease heats of formation. An analysis of the bond dissociation energies and impact sensitivity shows that all compounds have good stability. The crystal densities (1.82–2.00 g/cm³) computed from molecular packing calculations are big for all compounds and that of the –NF₂ derivative is the largest. All derivatives have higher detonation velocity and detonation pressure than PRAN. Compounds 3 and 4 (R = NO₂ and NF₂) have better performance than hexahydro‐1,3,5‐trinitro‐1,3,5‐trizine and the performance of 4 is quite close to that of 1,3,5,7‐tetranitro‐1,3,5,7‐tetraazacyclooctane, they are promising candidates of high energy compounds and worth further investigations. Copyright © 2012 John Wiley & Sons, Ltd.     

Comparative theoretical studies of high energetic cyclic nitramines

Density functional theory studies on cyclic nitramines were performed at B3LYP/6‐311G(d,p) level. The crystal structures were obtained by molecular packing calculations. Heats of formation (HOFs) were predicted through designed isodesmic reactions. Results indicate that the value of HOF relates to the number of =N–NO₂ group and aza nitrogen atom and increases with the augment of the number of =N–NO₂ group and aza nitrogen atom for cyclic nitramines. Detonation performance was evaluated by using the Kamlet–Jacobs equations based on the calculated densities and HOFs. All the cyclic nitramines exhibit better detonation performance than 1,3,5‐trinitro‐1,3,5‐triazacyclohexane and 1,3,5,7‐tetranitro‐1,3,5,7‐tetraazacyclooctane. The stability of cyclic nitramines was investigated by the bond dissociation energies. The result shows that the increase of =N?NO₂ group or aza nitrogen atom reduces the stability of the title compounds. These results provide basic information for molecular design of novel high energetic density materials. Copyright © 2013 John Wiley & Sons, Ltd.     

Theoretical investigation of a series of bis(1H-tetrazol-5-yl)furazan and bis(1H-tetrazol) derivatives as high-energy-density materials

Using density functional theory (DFT), a series of bis(1H-tetrazol-5-yl)furazan and bis(1H-tetrazol) derivatives with different linkages and substituents are investigated theoretically as potential high-energy-density materials (HEDMs). The heat of formation (HOF), detonation properties, natural bond orbital (NBO) and thermal stabilities are calculated and reported. The introduction of a furazan ring, an –N=N– bridge group and an –N₃ substituent is beneficial to increase the HOF of the title compounds. NBO analysis shows that there are electronic delocalisation effects among the bridge groups, furazan and tetrazole rings, and substituted groups. The conjugation effects and electronic transitions are influenced by the different linkages and substituents. The estimated detonation velocities and pressures indicate that the –ONO₂ and –NO₂ groups and the –N=N– linkage play important roles in enhancing the detonation properties. The bond dissociation energy (BDE) calculations reveal that the –NO₂ group is the substituent group which causes the least thermal stability. The bond between the substituent group and the tetrazole ring is the weakest bond in the title molecules. Considering the detonation performance and the thermal stability, 17 compounds may be promising candidates for HEDMs with good performance. Eight of them (A3, A4, C3, C4, D3, F3, G1 and G3) have better detonation properties than HMX.     

Theoretical study of energetic trinitromethyl‐substituted tetrazole and tetrazine derivatives

Density functional theory method was used to study the heats of formation, energetic properties, and thermal stability for a series of trinitromethyl‐substituted tetrazole and tetrazine derivatives with different substituents. It is found that the group ―NO₂, ―NHNO₂, or ―NF₂ play a very important role in increasing the heats of formation of the derivatives. The calculated detonation velocities and pressures indicate that the group ―CF₂NF₂, ―NHNO₂, ―1H‐tetrazolyl, ―2H‐tetrazolyl, or ―1,2,4,5‐tetrazinyl is an effective structural unit for enhancing their detonation performance. An analysis of the bond dissociation energies for several relatively weak bonds indicates that incorporating the group ―NHNO₂ and ―NH₂ into parent ring decreases their thermal stability. Considering the detonation performance and thermal stability, 37 compounds may be considered as the potential high‐energy compounds. Their oxygen balances are close to zero. These results provide basic information for the molecular design of novel high‐energy compounds. Copyright © 2013 John Wiley & Sons, Ltd.     

Theoretical studies on the structure,sensitivity, density,thermodynamic properties and detonation performance of dinitrobitriazoles

Azodinitro- and dinitroethylene-bridged bitriazoles are of interest in the contest of high explosives, and were found to have true local energy minima at the B3LYP/aug-cc-pVDZ level of theory. The optimised structures, vibrational frequencies and thermodynamic quantities for bitriazoles were obtained in the ground state. Kamlet–Jacobs equations were used to evaluate the performance of bitriazoles based on the predicted density and the calculated heat of explosion. Detonation properties (D = 8.12 to 9.23 km s^?1 and P = 28.0 to 39.83 GPa) of bitriazoles were found to be promising compared with those of hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX, D = 8.75 km s^?1 and P = 34.7 GPa) and octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX, D = 8.96 km s^?1 and P = 35.96 GPa). The fusion of azoles particularly appears to be a promising area for investigation, since it may lead to the desirable consequences of higher heat of explosion, higher density and thus improved detonation performance.     

Fe（II）-NH(a1Δ)N4S2自旋翻转单分子磁体的电子输运性质

Spin-crossover (SCO) magnets can act as one of the most possible building blocks in molecular spintronics due to their magnetic bistability between the high-spin (HS) and low-spin (LS) states. Here, the electronic structures and transport properties through SCO magnet Fe(II)-N₄S₂ complexes sandwiched between gold electrodes are explored by performing extensive density functional theory calculations combined with non-equilibrium Green''s function formalism. The optimized Fe-N and Fe-S distances and predicted magnetic moment of the SCO magnet Fe(II)-N₄S₂ complexes agree well with the experimental results. The reversed spin transition between the HS and LS states can be realized by visible light irradiation according to the estimated SCO energy barriers. Based on the obtained transport results, we observe nearly perfect spin- filtering effect in this SCO magnet Fe(II)-N₄S₂ junction with the HS state, and the corresponding current under small bias voltage is mainly contributed by the spin-down electrons, which is obviously larger than that of the LS case. Clearly, these theoretical findings suggest that SCO magnet Fe(II)-N₄S₂ complexes hold potential applications in molecular spintronics.