Frequency stabilization of a Q-switched Nd:YAG laser oscillator with stability better 300 kHz following an rf-sideband scheme

A frequency stabilization scheme following the Pound-Drever-Hall technique modified with a sample and hold circuit has been applied to a Q-switched diode-pumped Nd:YAG ring oscillator. The high-power ring is injection seeded by a monolithic non-planar ring laser oscillator (NPRO). The slave oscillator emits pulses of 23 ns duration and 20 mJ pulse energy with almost diffraction limited beam quality (M² = 1.2) at a repetition rate of 400 Hz. The short-term fluctuation of the center frequency from pulse to pulse is 290 kHz. The oscillator is designed for applications within lidar measurements.     

Picosecond laser amplification system with 93 W high average power

A high average power picosecond laser amplification system with diode-end-pumped Nd:YVO₄ and diode-side-pumped Nd:YAG is described. Laser with power up to 92.7 W, repetition frequency of 73.3 MHz, pulse duration of 26.5 ps, and beam quality of M² < 3.5 is generated in the amplification system. Thermal-birefringence-induced depolarization in the Nd:YAG rod laser head amplifier is measured to be 21.9 W though birefringence compensation is performed.     

QCW diode-pumped 654 W AO Q-switched Nd:YAG rod oscillator-amplifier laser

A diode laser-pumped acoustic-optic Q-switched Nd:YAG master-oscillator power amplifier laser is presented. The laser is quasi continuously pumped at 1.1 kHz with a pulse width of 172 μs, and the ultrasonic frequency of the AO Q-switcher is set at a higher value (53 kHz). The master oscillator is designed as a thermally near-unstable-resonator, which presents an average output power of 48 W with a beam quality value of M² = 1.41 and a Q-switching pulse duration of 121 ns. The maximum average power of the MOPA system is 654 W, and the beam quality is M² = 6.     

Self-Q-switched and mode-locked 946 nm Cr,Nd:YAG laser

A simultaneous self-Q-switched and mode-locked diode-pumped 946 nm laser by using a Cr,Nd:YAG crystal as gain medium as well as saturable absorber is demonstrated for the first time as we know. The maximum average output power of 751 mW with a slope efficiency of 18.38% is obtained at an intra-cavity average peak power intensity of 4.83 × 10⁶ W/cm². Under this circumstance, the repetition rate of Q-switched envelopes is 9.63 kHz and the pulse width is about 460 ns. Almost 100% mode-locked modulation depth is obtained at all time in the experiment process whether the incident pump power is low or high. The repetition rate of mode-locked pulses within a Q-switched envelope is 135.13 MHz and the mode-locked pulse width is within 600 ps. The laser produces high-quality pulses in TEM₀₀-mode in the simultaneous self-Q-switched and mode-locked experiment.     

LD end pumped, actively mode locked and passively Q-switched Nd:YAP laser at 1341 nm

An end pumped Nd:YAP laser at 1341 nm is actively mode locked and passively Q-switched. Pumping was done with a pulsed high power laser diode with maximum power 425 W. V³⁺:YAG with 61% initial transmission served as saturable absorber, and an acousto-optic modulator is used for active mode locking. The output pulse train with 69 ns duration has a total energy of 3.2 mJ with ±4% shot-to-shot fluctuation. The peak output energy of a single mode locked pulse is 0.25 mJ. The pulse duration of a single mode locked pulse is less than 800 ps. The output laser beam is nearly diffraction limited with 1.6 mm diameter, and beam propagation factor M² about 1.3.     

Efficient generation of 200 mJ nanosecond pulses at 100 Hz repetition rate from a cryogenic cooled Yb:YAG MOPA system

A diode-pumped Master Oscillator Power Amplifier (MOPA) laser system based on cryogenic cooled Yb:YAG has been designed, developed and its output performance characterised. The laser system consists of a fibre oscillator, an active mirror regenerative amplifier and a four pass main amplifier. 2.4 mJ, 10 ns, 100 Hz seed pulses from the fibre oscillator/regenerative amplifier arrangement were amplified up to pulse energies of over 200 mJ by using the four pass main amplifier arrangement. As a further study we have obtained an increased slope efficiency of 40% and an optical-to-optical efficiency of 30% using a pinhole vacuum spatial filter/image relay for laser mode control. With 1.8 mJ input seed pulses, output pulse energies of around 150 mJ were achieved.     

43 W picosecond laser and second-harmonic generation experiment

Combining the advantages of diode-end-pumped Nd: YVO₄ and diode-side-pumped Nd: YAG amplifiers, a high average power and high beam quality picosecond laser is designed. The system delivers a picosecond laser with average power of 43.4 W and good beam quality of M² < 1.7. By focusing the high power picosecond laser in LBO crystal, 532 nm green laser with maximal power of 20.8 W is generated and the conversion efficiency of second-harmonic generation reaches 56.4% when 17.7 W green laser obtained from the fundamental frequency laser with power of 31.4 W and beam quality of M² < 1.25.     

Large aperture tapered fiber phase conjugate mirror in MOPA laser systems with high repetition rate and high pulse energy

A large aperture tapered fused silica fiber phase conjugate mirror with a maximum 50.7% stimulated Brillouin scattering (SBS) reflectivity is presented, which is operated with 400 Hz pulse repetition rate and 36.5 mJ input pulse energy. To the best of our knowledge, it is the first time that over 50% SBS reflectivity is achieved by using solid-state phase conjugate mirror under such high pulse repetition rate and high pulse energy. With much higher pulse repetition rate of 500 and 1000 Hz, the maximum SBS reflectivity is 41.2% and 33.3%, respectively. A single-longitudinal-mode Nd:YAG laser is experimentally studied with master oscillator power amplifier (MOPA) scheme using such a tapered fiber as a phase conjugate mirror. A 101 mJ pulse energy is achieved at 400 Hz repetition rate, with a pulse width of 6 ns and a M² factor of less than 2. The corresponding peak power reaches 16.8 MW.     

An 8.1 W diode pumped solid-state quasi-continuous-wave yellow laser at 589 nm by intracavity sum-frequency mixing generation

We report an L-shaped symmetrical co-folding-arm plane-plane diode pumped solid-state yellow laser at 589 nm by using intracavity sum-frequency mixing. By carefully designing the cavity and employing various techniques to optimize the laser’s specifications, a quasi-continuous-wave (QCW) free-oscillation yellow laser source, which has an average output power of 8.1 W, a beam quality factor of M² = 2.3, and a repetition rate of 1.1 kHz, is developed. The generation of yellow laser at 589 nm is achieved by intracavity sum-frequency mixing between the laser lines at 1319 nm and 1064 nm of an Nd:YAG laser in a KTP crystal. To the best of our knowledge, the 8.1 W output at 589 nm is higher than any other diode pumped solid-state yellow laser generated by intracavity sum-frequency generation so far.     

400 Hz高光束质量高功率短脉冲激光器

研制了大能量高光束质量短脉冲激光器,系统采用主振荡+预放大器+主放大器2级主振荡功率放大器(MOPA)结构。采用双棒热效应补偿改善光束质量的措施,在重复频率400 Hz时实现单脉冲能量40 mJ、光束质量因子约为1.2的激光输出。激光器放大后实现单路脉冲能量712.5 mJ、脉宽12.4 ns的激光输出,采用球差补偿的方法提高了激光器的光束质量,在最大输出功率下实现了光束质量因子小于2.3,光光效率27.7%。偏振合束后,激光器输出能量大于1.4 J。     

AOM fourfold pass for efficient Q-switching and stable high peak power laser pulses

We report on a scheme for efficient acousto-optical Q-switching. A flash lamp pumped Nd:YAG oscillator with an acousto-optic modulator (AOM) fourfold pass configuration is presented. The setup combines two important advantages: enhancement of the diffraction efficiency by additional AOM passes and a compact oscillator design in spite of an extension of the optical path length. A flash lamp pumped oscillator with an average output power of 7 W and a beam quality of M² = 1.2 is developed. The system operates with a 100 Hz repetition rate for the flash lamps. In each pumping pulse a pulse train of 1 up to 40 Q-switched laser pulses is generated. The pulse duration is from 15 to 120 ns. In comparison to a former setup (AOM double pass) the AOM fourfold pass configuration allows single pulses with energy above 20 mJ and a pulse peak power of more than 1 MW. In addition, the beam profile is improved due to a better separation of the incident and diffracted beam caused by the AOM. The laser is dedicated as master oscillator in a master oscillator power amplifier (MOPA) system where pulse peak powers in the MW range should be achieved.     

Intracavity frequency doubling of an active Q-switched Nd:YAG laser with 2.25 W output power at 473 nm

An active Q-switched diode-end-pumped Nd:YAG laser is reported with 2.9 W output power on the ⁴F_3/2 → ⁴I_9/2 transitions at a pump power of 24 W. With intracavity frequency doubling using a 20-mm-long LBO, a maximum blue output power of 2.25 W is achieved at a repetition rate of 23 kHz. The conversion efficiency from the corresponding Q-switched fundamental output to blue output is 96%. The peak power of the Q-switched blue pulse is up to 610 W with 160 ns pulse width. The fluctuation of the blue output power is less than 4.0% at the maximum output power.     

Diode-pumped passively Q-switched Nd:GdVO4 laser at 1342 nm with V:YAG saturable absorber

We have demonstrated an efficient diode-pumped passively Q-switched Nd:GdVO₄ laser working at 1342 nm by using an uncoated V³⁺:YAG crystal as the saturable absorber, in which both a-cut and c-cut Nd:GdVO₄ crystals are employed. At the maximum absorbed pump power of 9.45 W, the maximum average output power can reach 519 mW and 441 mW corresponding to the output coupler with different transmission of 3% and 10% by using an a-cut Nd:GdVO₄ crystal at 1342 nm, while the shortest pulse duration could be as low as 21.7 ns and 22.3 ns with the repetition rate of 48.41 kHz and 53.25 kHz by using a c-cut Nd:GdVO₄ crystal, corresponding to the output coupler with different transmission of 3% and 10% at 1342 nm, and the single Q-switched pulse energy are 6.67 uJ and 7.06 uJ, the pulse peak power are 307 W and 316 W, respectively. The experimental results show that c-cut Nd:GdVO₄ laser can generate shorter pulse with higher peak power in comparison with a-cut one.     

Millijoule intracavity OPO driven by a passively Q-switched Nd:YVO<Subscript>4</Subscript> laser with AlGaInAs quantum-well saturable absorber

We originally demonstrate the use of an AlGaInAs periodic quantum-well absorber to achieve a quasi-continuous-wave (QCW) diode-pumped passively Q-switched Nd:YVO₄ laser with an intracavity optical parametric oscillator (OPO). With a diode-pumping energy of 35 mJ, the output pulse energy and the pulse width at 1573 nm are found to be 1.58 mJ and 26 ns, respectively. The pulse repetition rate can be up to 100 Hz with the overall OPO beam quality M² factor to be better than 1.5.     

Reflective carbon nanotube as the saturable absorber for mode-locked 1064 nm laser

With a reflective single-walled carbon nanotube as the saturable absorber, a laser diode-pumped passively mode-locked Nd:YVO₄ laser at 1064 nm was realized for the first time. The pulse duration of 12 ps was produced with a repetition rate of 83.7 MHz. The peak power and the single pulse energy of the mode-locking laser were 1.28 kW and 15.4 nJ, respectively.     

532 nm laser based on V-type doubly resonant intra-cavity frequency-doubling

LD side-pumped dual interconnected V-type quasi-continuous wave green laser has been demonstrated. The two Nd:YAG modules were placed in a plane-concave V-type resonator and a plane-concave straight cavity formed two stable operation beam of the 1064-nm fundamental frequency laser. Through acousto-optic Q-switched and frequency doubling crystal, two double-frequency laser beams arrived at the folded flat mirror, which were unidirectional output by the folded flat mirror at the end. As the pumped current was 50 A, the 532 nm green laser maximum average output power of 206 W at a repetition of 22.4 kHz was achieved with a pulse width of 201 ns and the largest single pulse energy of 9.2 mJ, corresponding to a peak power of 45.8 kW and a double frequency efficiency of 60.2%.     

678 nm RTP electro-optical Q-switched ceramic laser

The RTP electro-optical Q-switched ceramic laser at the wavelength of 678 nm with narrow pulse width is studied. We used the laser diode arrays side-pumped Nd:YAG ceramic crystal with 1.1 at% Nd doping and dimensions of Φ3 mm × 50 mm, designed folding cavity parameters, and discussed the variation of the beam radius in the ceramic crystal and frequency doubling crystal with the thermal focal length of ceramic crystal or KTP crystal. By using double RTP crystals as electro-optic Q-switch and KTP crystal type II phase matching for intracavity frequency-doubling, a narrow pulse width electro-optical Q-switched Nd:YAG ceramic laser was obtained. The output energy of 0.9 mJ and the pulse width of 41.6 ns at 678 nm are obtained at the repetition rate of 1000 Hz and pumped power of 144 W. The results formed the basis for the further development of the high power and high efficiency ceramic red laser.     

Diode-pumped passively Q-switched Nd:LuVO4 laser at 916 nm

We demonstrate a passively Q-switched Nd:LuVO₄ laser at 916 nm by using a Nd, Cr:YAG crystal as the saturable absorber. As we know, it is the first time to realize the laser with a simple linear resonator. When the incident pump power increased from 14.6 W to 23.7 W, the pulse width of the Q-switched laser decreased from 24 ns to 21 ns. The pulse width was insensitive to the incident pump power in the experiment. The average output power of 288 mW with repetition rate of 39 kHz was obtained at an incident pump power of 22.5 W, with the optical-to-optical efficiency and slope efficiency 1.3% and 3.6%, respectively.     

High efficiency TEM00 mode, diode-pumped, conduction-cooled, Nd:YAG zig-zag slab laser

We report a compact, conduction-cooled, highly efficient, continuous wave (CW) Nd:YAG slab laser in diode-side-pumped geometry. To achieve high efficiency, a novel laser head for Nd:YAG slab has been developed. For an absorbed pump power of 27.6 W, maximum output power of 10.4 W in multimode and 8.2 W in near-diffraction-limited beam quality has been obtained. Slope and optical-to-optical conversion efficiencies are 45.3% and 37.7% in multimode with beam quality factors (M²) in x and y directions equal to 32 and 8, respectively. TEM₀₀ mode operation was achieved in a hybrid resonator with slope and optical-to-optical conversion efficiencies of 43.2% and 29.7%, respectively. Beam quality factors in x and y directions are ?1.5 and ?1.6 for the whole output power range. The laser radiation was linearly polarized and polarization contrast ratios are >1200:1 in the multimode and 1800:1 in the TEM₀₀ mode operation. In passive Q-switching with Cr⁴⁺:YAG crystal of 68% initial transmission, 18 ns pulsewidth has been achieved with an average power of 2 W at a repetition rate of 16 kHz.     

Injection-Seeded 500 Hz Repetition Rate High Peak Power Single-Frequency Nd:YAG Laser for Mid-Infrared Generation

We develop an injection-seeded single-frequency neodymium-doped yttrium aluminum garnet (Nd:YAG) laser with 500 Hz repetition rate and high peak power. The laser construction is designed as seed injection and master oscillator power amplifier (MOPA) including single-frequency master oscillator, extra-cavity frequency doubling crystal, and round-trip power amplifier. The master oscillator can emit 1,064 nm laser of 8.4 mJ with 6.8 ns pulse width at the pump energy equal to 23 mJ. A green laser energy of 1.1 mJ is obtained by setting the proper temperature of the LBO crystal. The pulse energy of 1,064 nm laser decreases to 6.5 mJ after passing through the LBO crystal and rises to 25.3 mJ after a round-trip power amplifier corresponding to the extraction efficiency of 29%. The final output pulse width is 6.5 ns, representing a peak power of 3.9 MW. The 1,064 nm laser beam quality factor M² of the master oscillator and the amplified one are 1.3 and 1.5, respectively. The laser will be used to generate mid-infrared where the 532 nm laser with narrow pulse width is to pump sheet optical parametric oscillator (OPO) and the 1,064 nm laser with high peak power to pump the OPO.