液体介质快脉冲电压下击穿特性研究

设计了液体介质快脉冲击穿试验装置和电压电流测量系统，研究了重复频率、电极形状及电极间距与介质击穿场强、击穿电压和击穿时延等击穿特性参数的关系，比较了变压器油、十二烷基苯、蓖麻油三种典型液体绝缘介质在直流及快脉冲电压作用下的绝缘性能。结果表明:短脉冲持续时间下液体绝缘材料有异常高的击穿场强；重复脉冲串作用下的击穿场强比单个脉冲下明显减小，重复频率2 kHz时击穿场强减小了约30％；电极头半径大小对击穿也有影响，半径R＝5 mm时，击穿电压最高；击穿时延随击穿场强减小而变长，在其他条件相同的情况下，测得击穿时延随机波动；蓖麻油的快脉冲电压绝缘性能最好，变压器油次之。     

Semianalytical analysis of thermal effect in LD double-side-pumped rectangular laser crystal

A semianalytical method to analyze the thermal effect in a LD double-side-pumped rectangular laser crystal is put forward. Through the analysis of working characteristics of the laser crystal, a thermal model that matches actual situations of the laser crystal is established. General expressions of temperature field and thermal distortion field in the laser crystal can be obtained by a novel method to solve the heat conduction equation of orthotropic material. This semianalytical method can be used to calculate the temperature field and thermal distortion field in other LD double-side-pumped laser crystals and is applied to Nd:YVO₄ crystal in detail in this paper, and two methods of effectively reducing thermal distortion in the laser crystal are offered. Results show that a maximum temperature rise of 362.2 °C and a maximum thermal distortion of 5.55 μm are obtained in Nd:YVO₄ crystal when the output power of the two laser diodes are both 30 W. When the off-center distance is 0.6 mm, the maximum thermal distortion is reduced by 37.7%; when the thickness of the crystal is reduced from 2.0 mm to 1.4 mm, the maximum thermal distortion is reduced by 31.7%. Results in this paper can offer theoretical base for better solving thermal problems in laser system.     

LD泵浦高功率高斜效率Nd:YVO4声光调Q激光器

 报道了采用激光二极管(LD)端面泵浦Nd:YVO₄双端键合晶体高平均功率高斜效率1 064 nm声光调Q激光器。通过对大功率泵浦情况下激光晶体热透镜效应进行分析和估算,优化了模式匹配及热稳腔结构参数,实现了稳定的高功率高斜效率准连续脉冲激光输出。在泵浦功率46.8 W、最高重复频率50 kHz下,获得最大平均输出功率17.6 W,光-光转换效率为37.6%,斜效率达70.1%,脉冲宽度51.3 ns;在最低重复频率10 kHz下,获得最大单脉冲能量0.91 mJ,峰值功率为46.2 kW,脉冲宽度为19.8 ns。     

不同泵浦光下Nd:GdVO4晶体输出特性

为研究808 nm和879 nm两种泵浦光对Nd:GdVO4晶体激光输出特性的影响,并比较两种不同波长泵浦所得连续输出光的效率高低,分析了Nd:GdVO4晶体的能级结构和两种泵浦光作用下的激光输出特性,发现在879 nm也有较强的吸收峰.用808 nm和879 nm两种不同波长泵浦Nd:GdVO4晶体的过程是不同的,808 nm泵浦是一种间接方式能量转移的过程,在此过程中有明显的热负载产生.而879 nm泵浦是将粒子直接激励到激光辐射上能级,降低无辐射弛豫过程产生的热量.从理论上可知,879 nm的泵浦量子效率要高于808 nm的泵浦量子效率,对减少晶体的热产生有很强的优势.实验中采用激光二极管端面泵浦Nd:GdVO4晶体直腔方案,研究了两种不同泵浦光泵浦Nd:GdVO4晶体以获得1 063 nm的连续光,得到了两种光抽运时的斜效率,发现在同样实验条件下,879 nm泵浦的输出光斜效率在小功率泵浦时略高于808 nm|而在大功率泵浦的情况下明显高于808 nm,最高达到38%.同时,在808 nm抽运时,实验上获得了1 341 nm波长的激光,为光通讯的应用提供了一种光源.     

用于光生毫米波的双频微片激光器热致频差特性研究

研究了激光二极管端面抽运的双纵模双频微片激光器的热效应对其输出频谱的影响. 通过对端面抽运Nd:YVO₄微片的热传导方程求解得出晶体内部的温度场分布; 并进一步对微片晶体热致折射率变化进行分析, 由此计算出双频微片激光器的热致频谱变化. 实验结果表明: 当抽运功率较小时得到稳定的双纵模双频激光输出; 当抽运功率增大时, 晶体热效应使双频激光频谱双峰之间的频差减小, 各纵模波长频谱宽度加宽, 实验结果与理论分析相符合. 关键词： 光载无线通信 双频微片激光器 热效应 频率差     

采用解析法对Nd:YAG单晶光纤的温度场研究

采用解析法对Nd:YAG单晶光纤激光器热效应相关的光纤温度场分布进行研究。建立了Nd:YAG单晶光纤热模型,在单晶光纤所满足的边界条件下通过解析求解热传导方程,得到在高功率808 nm泵浦光抽运下产生946 nm激光的单晶光纤温度场分布,并与传统Nd∶YAG激光晶体的温度场进行比较,然后分别与同泵浦条件下的有限元数值方法的分析结果进行研究对比,最后分析泵浦光参数、单晶光纤参数等对温度场的影响。结果表明,功率为86 W的泵浦光入射至单晶光纤端面的最高温升仅为30.98℃,明显优于同泵浦条件下传统Nd∶YAG晶体的端面温升结果94.37℃,与有限元数值法得到的Nd:YAG单晶光纤19℃温升结果相比,该解析法结果更接近于实验的测量值31℃,能够更精确描述晶体光纤温度场。本文可对单晶光纤激光器热效应的精确研究提供一定参考,进而有利于提高单晶光纤激光器的性能。     

Theoretical study on thermal behavior of passively Q-switched microchip Nd:YAG laser

This study deals with the thermal characterization of a continuous wave (CW-) and end-pumped passively Q-switched microchip Nd:YAG laser crystal by solving the rate and heat transfer equations in the laser cavity. In this approach, a parametric study has been performed to investigate the influence of the pumping parameters, cooling metal dimension and also the crystal dimension and doping concentration on the thermal behavior of the laser crystal. Obtained results reveal a closed correlation between the mentioned parameters and the thermal behavior of the crystal indicating that a proper selection of the laser parameters is essential to control the crystal's temperature and improve the performance of the laser accordingly.     

Approximate formulas of temperature and stress distributions and thermal induced effects in a heat capacity slab laser

Approximate formulas of transient temperature and stress distributions in the slab of a two-side pumped heat capacity laser are attained by solving the heat diffusion equation. Based on the formulas, the distributions of temperature and stress during the pump period of a two-sided symmetrically laser diode array (LDA) pumped Nd:GGG slab laser with 5-kW average output power are numerically simulated. The results show that the temperature in the slab will averagely increase by more than 70 ℃ after operating for 10 seconds; the stress and maximum of the temperature difference in the slab are about 30 MPa and 24 ℃, respectively. The thermal induced effects are discussed also.     

激光二极管抽运Nd:YVO4晶体的三维热效应分析

针对激光二极管抽运的以Nd:YVO4板条晶体为增益介质的激光器件,基于有限容积法数值分析各向异性介质的热传导方程,给出了Nd:YVO4晶体板条结构的热分布数值模型,并分别模拟仿真了808nm半导体激光器双端端面抽运,大面均匀抽运,大面周期分布抽运三种抽运结构,得到了Nd:YVO4板条晶体在这三种抽运结构下的非稳态时不同时刻的温度曲线和稳态时的三维温度分布切面图.     

Study on optical characteristics of Nd:YVO4/YVO4 composite crystal laser

Thermal effect in crystals is the main obstacle blocking diode-pumped solid state laser to get high and stable output power. Diffusion bonding crystal has been demonstrated to be an effective method to relieve the thermal lensing theoretically based on the numerical heat analysis to the end-pumped anisotropic laser crystal. The temperature distributions in Nd:YVO4/YVO4 composite crystal and conventional crystal were analyzed and compared. The end-pumped Nd:YVO4/YVO4 composite crystal laser was designed and set up with z-cavity. The maximum output powers of 9.87 W at 1064 nm and 6.14 W at 532 nm were obtained at the incident pump power of 16.5 W. The highest optical-optical conversion efficiencies were up to 59.8% at 1064 nm and 37.2% at 532 nm respectively.     

第三类热边界条件对激光晶体热效应的影响

以各向异性半解析热分析理论为基础,研究矩形横截面Nd:YVO4激光晶体在有第三类热边界条件工作时,激光晶体温度场分布和晶体抽运面热形变分布.通过激光晶体工作特点分析,建立符合激光晶体工作状态的热模型.利用各向异性介质热传导方程的半解析求解方法,得出了矩形截面Nd:YVO4晶体的温度场、端面热形变场的通解表达式.研究结果表明:当使用输出功率为15 W半导体激光器端面中心入射Nd:YVO4晶体(晶体掺钕离子质量分数为0.5%)时,在抽运端面中心获得499.5 K最高温度和0.99 μm最大热形变量.和将第三类热边界条件近似为第二类热边界条件的通用做法相比更准确.这种方法可以应用到其它激光晶体热问题研究中,为有效解决激光系统热问题提供了理论依据.     

Diode-pumped continuous-wave eye-safe Nd:YAG laser at 1415 nm

We describe the output performance of the 1415 nm emission in Nd:YAG in a plane-concave cavity under traditional pumping into the 4F5/2 level (808 nm) and direct in-band pumping into the 4F3/2 level (885 nm). An end-pumped Nd:YAG laser yielded maximum cw output power of 6.3 W and 4.2 W at 885 nm and 808 nm laser diode (LD) pumping, respectively. To the best of our knowledge, this is the highest output power of a LD-pumped 1415 nm laser.     

波面热畸变自校正型板条增益介质的瞬态温度分布

提出一种新的激光增益介质板条抽运结构,这种结构能对由激光增益介质板条温度分布不均所造成的波面热畸变实现自校正,并建立了这种抽运结构下激光增益介质板条的瞬态温度分布理论模型,通过解热传导方程,推导出板条增益介质的瞬态温度分布的解析表达式。同时对抽运参量分别为抽运脉冲能量为5.8×104J、抽运重复频率为2Hz和抽运脉冲能量为3.2×104J、重复频率为10Hz两种情况下两种下N-31型钕玻璃板条的瞬态温度分布分别进行了数值计算,分别给出两种情况下10s内和60s时钕玻璃板条的温度分布图并对结果进行了分析和对比,表明采用这种抽运结构的增益介质板条激光器可以以类似热容激光器的方式在短时间内实现高平均功率、高光束质量运转。     

大口径LD泵浦的激光放大器热沉积特性

 通过分析LD阵列端面泵浦片状放大器的工作特点，建立了对增益介质Nd:YLF进行热特性研究的有限元模型。针对泵浦能量空间均匀分布、高斯分布、超高斯分布三种情况，计算出了LD泵浦功率56 kW，脉冲宽度520 μs，重复频率10 Hz状态下晶体瞬时3维温度和热应力分布。研究结果表明：由于脉冲工作方式，晶体各节点温度随时间呈锯齿形变化，经过一段时间后吸热和冷却效果达到平衡，介质温度呈周期性变化；在相同泵浦峰值功率条件下，超高斯泵浦能量分布引起的温升和热应力最小，其最大值分别为103.3 ℃和47.6 MPa；有效泵浦功率密度达到10 kW/cm²量级时，介质极可能发生热致断裂。     

Investigation of laser diode face-pumped high average power heat capacity laser

The three-dimensional (3D) pump intensity distribution in medium of the laser diode (LD) pumped highaverage power heat capacity laser is simulated by the ray tracing method, and the divergence characteristicsof fast axis and slow axis of LD are simultaneously considered. The transient 3D temperature and stressdistributions are also simulated by the finite element method (FEM) with considering the uneven heatsource distribution in medium. A LD face-pumped Nd:GGG heat capacity laser is designed. The averageoutput power is 1.49 kW with an optical-optical efficiency of 24.1%.     

基于水、风混合型冷却系统的LD端面泵浦全固态连续绿光激光器

为了简化激光器冷却系统,减小体积,降低成本,设计出一种基于水、风混合型的冷却系统,具有水冷和风冷的优点,可以实现稳定的绿光激光输出.采用结构简单、紧凑的平-凹腔设计,其端镜为平面镜,输出镜为凹面镜,曲率半径R=1 m,腔长L=165 mm,获得较稳定的单端泵浦Nd:YVO4腔内倍频KTP连续绿光激光输出.当晶体吸收的泵浦功率为24.3 W时,532 nm激光功率达到4.2 W,光-光转换效率达到17.2%.在绿光输出功率为3 W的情况下,观测到的变化范围在2.5%左右,温度变化范围在0.1°左右.实验结果表明,该冷却系统能够较好地转移晶体热效应产生的热量,实现转化效率较高的绿光输出,有利于实现高功率激光器的微型化.     

激光二极管泵浦Nd：YVO4／LBO腔内倍频瓦级连续波绿光激光器

报道一种激光二极管端面泵浦ＮｄＹＶＯ４晶体、ＬＢＯ腔内倍频的全固态瓦级连续波（ＣＷ）绿光激光器。对ＬＢＯ采用Ｉ类非临界相位匹配（ＮＣＰＭ）、温度调谐，当泵光功率为５．５Ｗ时，获得了１．２ＷＴＥＭ００模５３２ｎｍ连续波绿光输出，光－光转换效率达２２％，电－光转换效率达３％。     

双端抽运热容激光器温度特性分析

通过对激光二级管阵列双端抽运热容激光器晶体的分析,建立了热传导模型及边界条件.利用有限元方法模拟了晶体的温度场分布,并分别对抽运光斑直径、抽运持续时间、抽运光强和晶体端面尺寸等因素对温度场分布的影响进行了分析,得到了热容工作模式下的激光器温度特性.结果表明,晶体端面温差随抽运光斑直径的增大先增后减,存在一个极大值,并且在不同抽运光强下,出现端面温差极大点时的抽运光斑直径不变.     

激光二极管端面纵向泵浦Nd:YVO_4激光器的热效应研究

针对激光二极管端面纵向泵浦Nd:YVO4激光器,本文理论和实验详细研究了Nd:YVO4晶体的热透镜效应。在激光二极管的中心波长分别为808nm和880nm及分别采用单端端面纵向泵浦和双端端面纵向泵浦结构情况下,实验测量了Nd:YVO4晶体的热透镜焦距,实验结果和理论预测基本吻合。同时在泵浦功率60W时获得了18.8W的连续基横模激光输出。     

高功率半导体激光端面泵浦方形掺Nd3+离子激光晶体热形变研究

为了解决高功率半导体激光器端面泵浦激光晶体引起的热效应问题，激光晶体泵浦端面的热形变必须进行准确的计算.通过对于全固态激光器中激光晶体的工作特点分析，建立了矩形截面激光晶体热分析模型.基于热传导方程，提出了泊松方程的一种新解，并获得了矩形截面激光晶体端面热形变分布的一般解析表达式.同时讨论了半导体激光器偏心泵浦激光晶体给端面热形变带来的影响.与有限元分析方法以及其他数值分析方法相比，解析分析方法不会给计算引入任何的误差.热形变的解析分析为解决激光晶体的热效应问题以及提高激光器的性能提供了理论的依据.