Optics design and fabrication of 3D electrically switchable hexagonal photonic crystal

We demonstrate a holographic approach for easy and large-area fabrication of 3D photonic crystal (PhC) microstructures in a polymer-dispersed liquid crystal (PDLC) by applying a single top-cut hexagonal prism and a seven-beam interference system. Based on the expected photonic band gap of the photonic crystal, the prism parameters are designed and optimized. For example, a prism with a height h=3.73 cm and a cross angle α=66° between the side face and the base is used to fabricate 3D PhC hexagonal symmetrical structures in PDLCs. A good agreement is obtained between the theoretical calculation of the interference intensity and morphological structures. On the other hand, far-field diffraction patterns and electrical switching characteristics are also investigated. PACS 42.15.Eq; 42.40.Eq     

Enhancement of the light output of light-emitting diode with double photonic crystals

A light-emitting diode (LED) with double photonic crystals (PhCs) is designed to enhance the light output. Based on the configuration of the PhC assisted LED with a single PhC (SPC-LED), a second PhC is added on the bottom surface of the active layer to improve the light output. The optical properties of this double PhCs assisted LED are simulated using the three-dimensional (3D) finite-difference time-domain (FDTD) method. The calculation results show that its light output can be 3.2 times higher than that of LED without PhC, and 1.39 times higher than that of SPC-LED.     

Design and optimization of one-dimensional photonic crystals for thermophotovoltaic applications

We explore the optical characteristics and fundamental limitations of one-dimensional (1D) photonic crystal (PhC) structures as means for improving the efficiency and power density of thermophotovoltaic (TPV) and microthermophotovoltaic (MTPV) devices. We analyze the optical performance of 1D PhCs with respect to photovoltaic diode efficiency and power density. Furthermore, we present an optimized dielectric stack design that exhibits a significantly wider stop band and yields better TPV system efficiency than a simple quarter-wave stack. The analysis is done for both TPV and MTPV devices by use of a unified modeling framework.     

基于二维六方氮化硼材料的光子晶体非对称传输异质结构设计

二维六方氮化硼(hexagonal boron nitride,hBN)材料在产生光学稳定的超亮量子单光子光源领域有着潜在应用,有望用于量子计算和信息处理平台,已成为研究热点.而光学非对称传输设备是集成量子计算芯片中的关键器件之一.本文从理论上提出了一种基于hBN材料光子晶体异质结构的纳米光子学非对称光传输器件.运用平面波展开法研究了光子晶体的能带结构与等频特性,从理论上分析了hBN异质结构中可见光波非对称传输的可行性.同时,采用时域有限差分方法研究了可见光波段异质结构的晶格常数和半径对透射光谱的影响.研究结果显示,该结构实现了在610—684 nm波长范围内TE偏振光的非对称传输,在652 nm波长处正向透射率达到0.65,反向透射率为0.006,非对称传输透射对比度高达0.98.本文提出的结构模型为基于hBN的新型纳米光子器件设计提供了新的可能性,可用于不同功能光学器件的集成设计.     

Fabrication and demonstration of square lattice two-dimensional rod-type photonic bandgap crystal optical intersections

This paper reports fabrication and demonstration of optical intersections in two-dimensional (2D) rod-type photonic crystal (PhC) structures. High resolution and aspect ratio 2D square lattice PhC waveguide intersections were designed and fabricated for application at the optical communication wavelengths centered at 1550 nm. In the silicon processing front, challenges resolved to overcome issues of drastically reduced process windows caused by the dense PhC rods arrays with critical dimensions (CDs) reduced to only a few hundred nanometers were addressed not only in terms of critical process flow design but also in the development of each processing module. In the lithographic process of deep ultraviolet laser system working at 248 nm, PhC rods of sub-lithographic wavelength CDs (115 nm in radii) were realized in high resolution, even near periphery regions where proximity errors were prone. In the deep etching module, stringent requirements on etch angle control and low sidewall scallops (undulations arising from time multiplexed etch and passivation actions) were satisfied, to prevent catastrophic etch failures, and enable optical quality facets. The successfully fabricated PhCs were also monolithically integrated with large scale optical testing fiber grooves that enabled macro optical fiber assisted coupling to the micro scale PhC devices. In the optical experiments, the transmission and crosstalk properties for the PhC intersection devices with different rod radii at the center of the PhC optical waveguides crossings were measured with repeatability. The properties of the PhC intersections were therefore optimized and verified to correspond well with first principle finite difference time domain simulations.     

Air waveguide in a hybrid 1D and 2D photonic crystal hetero-structure

An air waveguide in hybrid one-dimensional photonic crystal and two-dimensional photonic crystal slab hetero-structure is designed. Light propagating in air waveguide can be confined by two-dimensional photonic crystal slab in x-y plane and one-dimensional photonic crystal films in z direction. Theoretical calculations show that air waveguide in the hetero-structure can achieve some functions as 3D PhCs but could be made more easily than 3D PhCs.     

纳米压印制备的光子晶体结构对AlGaN基材料深紫外出光效率的提高

通过利用阳极氧化铝的方法制备高度有序的光子晶体结构作为纳米压印模板,将大面积光子晶体图案转移到了样品表面,解决了国际上小尺寸光子晶体制备困难的问题。采用纳米压印的方法在AlGaN基样品表面上制备了290 nm的周期光子晶体结构,并将表面具有光子晶体结构的AlGaN基样品正面出光强度提高121%。偏振特性的实验结果表明六角排列的孔状光子晶体将原来朝向样品侧面传播的TE偏振光偏折转向正面,从而增加光抽取效率,改变出光偏振度。指出远场角分辨图案的变化归因于光子晶体对出光的衍射和Bragg散射效果。实验中采用的创新性工艺可以用来制备具有高出光效率的深紫外发光二极管。     

蛋白石型光子晶体红外隐身材料的制备

基于光子晶体的红外隐身材料,主要采取一维层层堆叠结构和三维木堆结构等来实现对红外波段电磁波辐射性能的调控.本文报道了一种操作简易、成本低廉的光子晶体红外隐身材料制备方法.通过优化的垂直沉积法,微米级SiO_2胶体微球自组装成高质量的蛋白石型光子晶体结构.对SiO_2胶体微球进行优选,成功制备了禁带位于2.8—3.5μm,8.0—10.0μm的SiO_2胶体晶体蛋白石型光子晶体材料.该材料可改变目标相应波段的红外辐射特征,具有目标红外波段的隐身效果.     

Demonstration of temperature resilient properties of 2D silicon carbide photonic crystal structures and cavity modes

In this paper, photonic crystal (PhC) based on two dimensional (2D) square and hexagonal lattice periodic arrays of Silicon Carbide (SiC) rods in air structure have been investigated using plane wave expansion (PWE) method. The PhC designs have been optimized for telecommunication wavelength (λ = 1.55 μm) by varying the radius of the rods and lattice constant. The result obtained shows that a photonic band gap (PBG) exists for TE-mode propagation. First, the effect of temperature on the width of the photonic band gap in the 2D SiC PhC structure has been investigated and compared with Silicon (Si) PhC. Further, a cavity has been created in the proposed SiC PhC and carried out temperature resiliency study of the defect modes. The dispersion relation for the TE mode of a point defect A1 cavity for both SiC and Si PhC has been plotted. Quality factor (Q) for both these structures have been calculated using finite difference time domain (FDTD) method and found a maximum Q value of 224 for SiC and 213 for Si PhC cavity structures. These analyses are important for fabricating novel PhC cavity designs that may find application in temperature resilient devices.     

Various photonic crystal structures fabricated by using a top-cut hexagonal prism

We demonstrate a holographic approach for the fabrication of large-area photonic crystal (PhC) microstructures by applying a single top-cut hexagonal prism (TCHP). The interference patterns of the beams from the TCHP are calculated. Various two-dimensional PhC structures are fabricated in photo-resist films. They include symmetrical hexagonal structures, the honey-comb structure and the hexagonal structure with skewed elliptical rods. The first structures come from six-beam and symmetrical three-beam interfering. The second structure appears when the beam is incident on the TCHP obliquely. The third structure is obtained when adjacent three beams or four beams are interfered. The period can be decreased to 285 nm. SPM observations of the PhCs provide the basis for measurement of their structural parameters. A good agreement is obtained for the measured structural parameters and calculated results for the PhCs. The photonic band gaps of the hexagonal symmetrical and honeycomb structures are derived by using the plane wave method. These results reveal that, by varying the number of split beams and the incident angle, using the single TCHP PhCs, different band gaps can be achieved.     

Photonic crystal LEDs – designing light extraction

Photonic crystals (PhCs) have attracted much attention during the last decade as a solution to overcome the low extraction efficiency of as‐grown light‐emitting diodes (LEDs). In this review we describe the underlying physics and summarize recent results obtained with PhC LEDs. Here, the main focus is on diffracting PhC. In order to quantify the benefit from the incorporation of PhCs for diffracting light a comparison by simulations between a PhC LED and a standard state‐of‐the‐art LED is carried out. Finally, the impact of the PhC on the LEDs emission characteristics will be discussed with respect to étendue‐limited applications.     

Photonic bands, gap maps, and intrinsic losses in three-component 2D photonic crystal slabs

We obtain the photonic bands and intrinsic losses for the triangular lattice three-component two- dimensional （2D） photonic crystal （PhC） slabs by expanding the electromagnetic field on the basis of waveguide modes of an effective homogeneous waveguide. The introduction of the third component into the 2D PhC slabs influences the photonic band structure and the intrinsic losses of the system. We examine the dependences of the band gap width and gap edge position on the interlayer dielectric constant and interlayer thickness. It is found that the gap edges shift to lower frequencies and the intrinsic losses of each band decrease with the increasing interlayer thickness or dielectric constant. During the design of the real PhC system, the effect of unintentional native oxide surface layer on the optical properties of 2D PhC slabs has to be taken into consideration. At the same time, intentional oxidization of macroporous PhC structure can be utilized to optimize the design.     

Modelling of a two-dimensional photonic crystal as an antireflection coating for optoelectronic applications

In article a two-dimensional photonic crystal (PhC) is considered and modelled as a new generation antireflection coating for optoelectronic devices. Traditional antireflective coatings (ARCs) reduce the reflection of the radiation only – the new generation of antireflective coatings should affect the distribution of the radiation also. Such functionality can be provided by the two-dimensional PhC which reduce the reflection and scatter transmitted light. Prior to the fabrication, the PhCs should be designed and analysed. Results of the analysis should provide quantitative means for choice of materials and design solutions. In work, we analyse the electromagnetic field distribution as Poynting vectors inside the materials of optoelectronic devices, in order to investigate the possibility of improving the construction of future optoelectronic devices. Furthermore, we calculate the reflection and transmission of that ARC. It’s a complex optic analysis of new generation of ARC. The numerical analysis has been performed with the FDTD method in Lumerical Software. In work, we consider the two-dimensional photonic crystal on the top surface of optoelectronic structures. We compared the results with the traditional ARC from these same parameters as PhC: thickness and material. As an example, we presented the application of modelled, photonic crystal, thin-film, GaAs solar cells with PhC on top. The efficiency of this solar cell, using the photonic crystal, was improved by 6.3% over the efficiency of this same solar cell without PhC. Thus, our research strongly suggests that the unique properties of the photonic crystal could be used as a new generation of ARC.     

Sensitivity improvement of broadband electro-optic polymer-based optical phase modulator using 1D and 2D photonic crystal structures

This Letter introduces the design and simulation of a microstrip-line-based electro-optic(EO) polymer optical phase modulator(PM) that is further enhanced by the addition of photonic crystal(PhC) structures that are in close proximity to the optical core. The slow-wave PhC structure is designed for two different material configurations and placed in the modulator as a superstrate to the optical core; simulation results are depicted for both1 D and 2D PhC structures. The PM characteristics are modeled using a combination of the finite element method and the optical beam propagation method in both the RF and optical domains, respectively.The phase-shift simulation results show a factor of 1.7 increase in an effective EO coefficient(120 pm/V) while maintaining a broadband bandwidth of 40 GHz.     

Four-port coupled channel-guide device based on 2D photonic crystal structure

We have fabricated and measured a four-port coupled channel-waveguide device using W1 channel waveguides oriented along ΓK directions in a two-dimensional (2D) hole-based planar photonic crystal (PhC) based on silicon-on-insulator (SOI) waveguide material, at operation wavelengths around 1550 nm. 2D FDTD simulations and experimental results are shown and compared. The structure has been designed using a mode conversion approach, combined with coupled-mode concepts. The overall length of the photonic crystal structure is typically about 39 μm and the structure has been fabricated using a combination of direct-write electron-beam lithography (EBL) and dry-etch processing. Devices were measured using a tunable laser with end-fire coupling into the planar structure.     

FDTD analysis of 2D triangular-lattice photonic crystals with arbitrary-shape inclusions based on unit cell transformation

A finite-difference time-domain method based on Yee’s orthogonal cell is utilized to calculate the band structures of 2D triangular-lattice-based photonic crystals through a simple modification to properly shifting the boundaries of the original unit cell. A strategy is proposed for transforming the triangular unit cell into an orthogonal one, which can be used to calculate the band structures of 2D PhCs with various shapes of inclusions, such as triangular, quadrangular, and hexagonal shapes, to overcome the shortage of plane-wave expansion method for circular one. The band structures of 2D triangular-lattice-based PhCs with hexagonal air-holes are calculated and discussed for different values of its radius and rotation angle. The obtained results provide an insight to manipulate the band structures of PhCs.     

光子晶体发光二极管光抽取效率及远场辐射特性的数值研究

运用三维时域有限差分法,研究了完美/缺陷光子晶体特定参量的改变对发光二极管光抽取效率影响,得出优化参量.基于近场远场转换,进一步分析了两种不同类型的缺陷引入及其周边空气孔半径的改变对光子晶体发光二极管远场辐射特性的影响.数值研究的结果表明,通过引入缺陷以及减小缺陷周围空气孔半径能够同时提高光子晶体发光二极管的光抽取效率和远场辐射方向性.     

Tunable transmission and enhanced emission in ordered metallic nanostructures having varying channel shape

Extraordinary transmission spectra for one-dimensional (1D) gratings and two-dimensional (2D) metallic hole arrays change with the hole channel shape. In this paper, a converging-diverging channel (CDC) design was introduced. The transmission spectra corresponding to CDC-embedded nanostructures of 1D grating, circular and rectangular holes (2D hole arrays) are analyzed using three-dimensional (3D) finite-element method. Tuning of optical transmission by changing the CDC structure has been investigated. In addition, a cavity composed of a CDC metallic grating and a 1D photonic crystal (PhC) can lead to an enhanced emission. Large coherence length of the emission can be achieved by exploiting coherent properties of surface waves in grating and PhC.     

Split-step finite-difference time-domain method with perfectly matched layers for efficient analysis of two-dimensional photonic crystals with anisotropic media

This Letter presents a split-step (SS) finite-difference time-domain (FDTD) method for the efficient analysis of two-dimensional (2-D) photonic crystals (PhCs) with anisotropic media. The proposed SS FDTD method is formulated with perfectly matched layer boundary conditions and caters for inhomogeneous anisotropic media. Furthermore, the proposed method is derived using the efficient SS1 splitting formulas with simpler right-hand sides that are more efficient and easier to implement. A 2-D PhC cavity with anisotropic media is used as an example to validate the efficiency of the proposed method.