芳纶纤维平纹织布在爆炸载荷下的动态响应与失效行为的数值分析

为了研究柔性纤维织布的抗爆性能,通过数值模拟的方法对芳纶纤维织布在爆炸冲击下的响应与失效行为进行了分析。对国产芳纶纤维织布H1000D-AP220进行了力学性能试验,建立了柔性平纹织布的本构模型和爆炸冲击数值分析模型,对不同厚度不同铺层角度织布进行了爆炸冲击数值分析,获得了织布在不同爆炸载荷下的动态响应和失效模式。结果表明,织布在爆炸冲击载荷下主要表现为中心撕裂破孔和简支边界处拉伸撕裂2种典型的失效模式,并伴有明显褶皱,宽度方向出现织布向内侧收缩翻转现象;相比于中间层织布,迎爆面和背爆面吸能较多;在计算分析中改变了织布的层叠角度,获得了更好的抗爆效果。     

爆炸和冲击载荷下金属材料及结构的动态失效仿真

通过数值模拟研究爆炸冲击载荷下金属材料和结构的动态失效规律对表征爆炸冲击毁伤效应及设计新型抗冲击结构具有重要意义.强动载下金属材料失效涉及材料大变形、热力耦合、材料状态变化等多个复杂物理过程,给数值仿真带来了极大挑战,其中包括裂纹、剪切带等复杂失效模式的几何描述、动态失效准则的确定、塑性与损伤耦合演化的描述等问题.针对这些挑战性问题,基于能量变分建立描述金属动态失效过程的热弹塑性相场理论和计算模型,实现了断裂与剪切带失效模式的统一描述,并提出了其显式有限元高效求解策略.进一步将该模型应用于爆炸冲击载荷下金属脆韧失效模式转变、绝热剪切带（ASBs）自组织及冲击波作用下薄壁圆盘失效形式转变三个典型金属动态失效问题,验证了理论模型的准确性及计算模型的稳健性.该工作为后续开展基于仿真的爆炸冲击毁伤评估及防护结构设计研究奠定了基础.     

Quantitative risk assessment of slope failure in 2-D spatially variable soils by limit equilibrium method

Quantitative risk assessment of slope failure is an important prerequisite for formulating rational strategies for landslide risk mitigation and developing a landslide risk-based warning system. Efficient risk assessment of slope failure in two-dimensional (2-D) spatially variable soils is a challenging problem. This paper proposes an efficient approach for quantitative risk assessment of slope failure considering the 2-D spatial variation of soil properties in the limit equilibrium analysis framework. To facilitate the risk assessment of slope failure, an empirical method is developed for the identification of slope key failure modes. With the proposed approach, the key failure modes of the spatially variable slope can be well identified and their contributions to the risk of slope failure can be effectively quantified. Finally, a two-layered soil slope is studied to illustrate the proposed approach. It is found that the prominent advantages of the proposed approach include being computationally efficient and accounting for the effect of the correlations among the failure modes.     

碳纤维/树脂基复合材料曲壁蜂窝夹芯结构的三点弯曲性能北大核心CSCD

为研究碳纤维复合材料(CFRP)曲壁蜂窝结构在三点弯曲载荷作用下的承载特性与失效模式,对不同芯层高度、面板厚度的结构进行了理论预报、数值模拟及试验.首先,根据夹芯结构的主要失效模式,提出了相应的理论预报公式,并绘制了失效机制图;其次,建立了CFRP曲壁蜂窝夹芯结构的有限元仿真模型,对其在三点弯曲载荷作用下的典型失效行为进行模拟;最后,通过模压成型工艺制备了不同尺寸的CFRP曲壁蜂窝夹芯结构,并将试验结果与理论、模拟结果进行比较.结果表明,蜂窝夹芯结构承载能力与芯层高度、面板厚度密切相关,结构芯层及面板刚度随其尺寸的减小而下降,导致结构失效模式由面芯脱黏失效变为面板压溃失效.     

A model of imperfect preventive maintenance with dependent failure modes

Consider a system subject to two modes of failures: maintainable and non-maintainable. A failure rate function is related to each failure mode. Whenever the system fails, a minimal repair is performed. Preventive maintenances are performed at integer multiples of a fixed period. The system is replaced when a fixed number of preventive maintenances have been completed. The preventive maintenance is imperfect because it reduces the failure rate of the maintainable failures but does not affect the failure rate of the non-maintainable failures. The two failure modes are dependent in the following way: after each preventive maintenance, the failure rate of the maintainable failures depends on the total of non-maintainable failures since the installation of the system. The problem is to determine an optimal length between successive preventive maintenances and the optimal number of preventive maintenances before the system replacement that minimize the expected cost rate. Optimal preventive maintenance schedules are obtained for non-decreasing failure rates and numerical examples for power law models are given.     

����Copulas�������������о���ʧЧģ�͵�ͳ�Ʒ���

在已有讨论竞争失效数据统计分析的文献中, 大多数都假设失效机理之间相互独立. 本文使用copula作为连接函数来考查加速寿命试验中的竞争失效模型. 通过模拟, 把失效机理相关时得到的结果与失效机理独立时得到的结果做了比较. 最后分析了文献中的一个实际数据.     

被检测系统的可靠性和最优检测策略

研究被检测系统的一个模型,假定系统有4种运行状态(正常工作、异常工作、正常故障和异常故障)．系统故障时不需检测,系统工作时必须经过检测才能知道它是正常还是异常．系统开始工作后,每隔一段随机时间对它检测一次,直到系统故障或检测出系统处于异常状态为止．利用概率分析和随机模型的密度演化方法,导出了系统的一些新的可靠性指标和最优检测策略．     

An Optimum Repair Policy for the Machine Interference Problem

This paper presents two repair policies for the machine interference problem where machines have two failure modes. In policy I priority of repair is assigned to one failure mode over the other, while in policy II the two failure modes have equal probability of repair. Computer programs were developed to obtain the optimal number of machines to be allocated to a single repair crew for the two policies. Under the same operating conditions, policy II is superior to policy I. The repair crew efficiency and machine availability were evaluated for both policies.     

The analyses of dynamic response and reliability for failure-dependent stochastic micro-resonator with thermoelastic coupling effects

A crucial measure for the design of high-performance micro-resonators is to consider the randomness of structural parameters when analyzing the structural system reliability. In this work, the stochastic dynamic response analysis and subsequently, a dynamic reliability assessment of the random micro-resonators are originally presented, where the thermoelastic coupling effects are freshly incorporated in the models proposed. The dynamic characteristics equation of the deterministic micro-resonator is firstly established based on the finite element method. The random dynamic characteristics of the resonator are then solved by implementing the left and right eigenvectors and the block Lanczos algorithm, and the random temperature field and structural random dynamic stress are also tackled. Afterwards, the overall structural reliability is investigated with a comprehensive consideration of the strength failure and frequency resonance failure, in which the Copula function is used for describing the dynamic correlation between two failure modes. Finally, the feasibility and rationality of the method put forward are demonstrated via a practically motivated example.     

Modeling of fiber-reinforced PMMA at different scales

This paper deals with the modeling of fiber-reinforced PMMA. Focus is on the macroscopic mechanical response with emphasis on the fracture properties such as the ultimate strength and the fracture energy. In order to capture the macroscopic mechanical response of PMMA, a finite element formulation is presented. While the elastic response of the fibres and that of the surrounding matrix are modelled in standard manner, i.e., by standard bulk material models, the relevant failure modes such as cracking of the fibres are accounted for by means of the so-called Strong Discontinuity Approach (SDA). Since the fibres are relatively small, their fracture mechanical properties crucially depend on their geometry, i.e., they show a pronounced size effect. Based on numerical analyses of fibres with different geometries, the aforementioned size effect is naturally incorporated into the formulation [1]. (© 2014 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim)