Design and analysis of multi-ring microstructured-core optical fibers

A novel design of single-mode large-mode-area optical fiber is presented. The core is composed of alternate high and low-index regions to form an effectively low-index contrast between the core and the cladding. The proposed fiber is investigated by the finite-element method with anisotropic perfect matched layer boundary conditions. In addition, the bending losses of the fibers are calculated and compared with those of the step-index optical fibers. In particular, numerical simulations demonstrate that single-mode operation can be achieved in one such fiber with mode area larger than 600 μm² at the wavelength of 1.55 μm and bending loss lower than 0.02 dB/m for bending radius greater than 20 cm.     

A novel broadband dispersion compensating square-lattice photonic crystal fiber

In this paper we propose a novel square-lattice photonic crystal fiber (SPCF) for dispersion compensation in a wide range of wavelengths. Perfectly matched layer (PML) is considered for the boundary treatment and an efficient compact two dimensional finite-difference frequency-domain (2-D FDFD) method is employed to model square-lattice photonic crystal fibers (SPCF). It has been shown with selecting appropriate parameters for SPCF it is possible to obtain high negative dispersion coefficient, negative dispersion slope over E to L wavelengths, confinement losses less than 10^?5?dB/m and splice losses less than 3.6 dB. The designed SPCF exhibits a relative dispersion slope (RDS) of 3.543 × 10^?3 nm^?1 which is closely matched to the RDS of conventional single mode fibers.     

Fine adjustment of cavity loss by Sagnac loop for a dual wavelength generation

We experimentally demonstrate a fine adjustment of cavity loss by Sagnac loop for a dual wave-length generation. The single or dual wavelengths are obtained by controlling the losses on both cavities through a fiber optical loop mirror (FOLM). Wavelength separation on the dual laser is 0.98 nm. The dual or single wavelength is obtained by changes in temperature in the order of 10⁻¹°C around the maximum in the FOLM. Also, we investigate energy fluctuations on signal level saturation effect in the cavity through different pumping power that act on the EDF, where we note that from the 60-mW pumping begins to generate dual-wavelength and 80-mW stabilizes.     

Cavity-enhanced spectroscopy in optical fibers

Cavity-enhanced methods have been extended to fiber optics by use of fiber Bragg gratings (FBGs) as reflectors. High-finesse fiber cavities were fabricated from FBGs made in both germanium/boron-co-doped photosensitive fiber and hydrogen-loaded Corning SMF-28 fiber. Optical losses in these cavities were determined from the measured Fabry-Perot transmission spectra and cavity ring-down spectroscopy. For a 10-m-long single-mode fiber cavity, ring-down times in excess of 2 ms were observed at 1563.6 nm, and individual laser pulses were resolved. An evanescent-wave access block was produced within a fiber cavity, and an enhanced sensitivity to optical loss was observed as the external medium's refractive index was altered.     

Tripartite entanglement of atoms trapped in coupled cavities via quantum Zeno dynamics

A scheme is proposed for the generation of a W state for three atoms trapped in spatially separated cavities connected by optical fibers via quantum Zeno dynamics. Our scheme is based on the resulting effective dynamics induced by continuous coupling between the atoms and cavities. The effects of decoherence such as atomic spontaneous emission and the fiber and cavity losses are considered. Numerical results show that the scheme is very robust against the cavity decay due to a tiny excitation probability of the cavity fields during the operation.     

Design and analysis of a photonic crystal fiber with four-hole unit

A novel photonic crystal fiber (PCF) based on a four-hole unit is proposed in order to meet the requirements of high birefringence, negative dispersion and confinement loss in fiber-optic communication. The proposed design has been simulated based on the full vector finite element method (FVFEM) and anisotropic perfectly matched layers (APML). Analysis results show that the proposed PCF can achieve a high birefringence to the order of 10⁻² at the wavelength of 1.55 μm, a large negative dispersion over a wide wavelength range and confinement losses lower than 10⁻⁹ dB/m simultaneously, which has important applications in polarization-maintaining (PM) fibers, single-polarization single-mode (SPSM) fibers, dispersion compensation fibers and so on.     

Self-mixing effect in Yb3+ doped DBR fiber laser with different linewidth enhancement factor

We present a self-mixing interference model approach to stimulate the self-mixing interference in YDBR fiber laser with optical self-mixing interference operating in the weak feedback regime. The self-mixing interference model includes Yb³⁺ doped fibers pumped at 920 nm, with distributed Bragg reflector mirrors at both fiber ends and external reflector. Using the quasi-analytical YDBR fiber laser model and self-mixing three-mirror cavity model, the output power expression is deduced and the Peak-to-Peak values and asymmetry values of self-mixing waveform at different linewidth enhancement factor have been studied in detail.     

Fabrication of low OH loss holey fibers with varying air hole sizes and their optical properties

We experimentally investigate a flexible fabrication technique for low OH and transmission losses holey fibers with a Ge-doped core and air holes in a silica cladding region. Versatile holey fibers of different size, pitch, and shape of air holes were achieved by controlling the temperature and heating time of the holey fiber preform. In addition, we suppress the OH loss of less than ∼0.323 dB/km at 1383 nm. After fabricating holey fibers, we measure their optical properties including cut-off wavelength, mode field diameter, splicing loss, dispersion, bending loss, and polarization dependent loss based on the size of air holes. The total transmission loss was measured to be ∼0.226 dB/km at 1550 nm by improving the fabrication process. After fabricating optical patch cord based on holey fibers, we measured the long-term stability of the fabricated holey fiber by using the temperature cycling technique for 24 and obtained low power fluctuation of 0.2 dB. We achieve the high quality holey fiber with a low bending loss of ∼0.04 dB/turn under a bending radius of 2.5 mm at 1550 nm. We also obtain a tunable band rejection filter with a number of bending turns.     

Field deformation and loss by curvature in gain guided and index anti-guided fibers

Gain guided and index anti-guided fiber, being a new kind of fiber with a great potential application on large mode area lasing devices, has the inevitable geometric curvature, which induces field deformation and bending losses. In this paper, the method of complex-value extended Fourier-Bessel series is introduced on optical field deformation and bending losses by geometric curvature in the case of this new fiber. Comparing with conventional fibers, gain guided and index anti-guided fiber has better performance on anti-curvature; the quantity of optical intensity centre being shifted from fiber geometric center is less than the case of conventional index guided fibers; and the bending losses decrease dramatically with the increase of curvature radius.     

新型全固态准晶体结构大模场光纤特性研究

大模场单模光纤在高功率激光器、高功率光传输和高灵敏度传感器等领域具有重要意义.设计了一种新型超低损耗大模场单模光纤,包层空气孔由掺氟硅玻璃棒代替,掺氟硅玻璃棒排列呈六重准晶体结构.基于有限元法对光纤的传输特性进行了数值模拟.研究了光纤结构参量变化对模式特性和有效模场面积的影响.结果表明:波长在1064 nm处,有效模场面积高达5197μm2,基模的限制性损耗低于10-5dB/km,解决了大模场与低损耗之间的冲突;在1064—2000 nm波段内,基模与二阶模的限制性损耗相差7个量级,实现单模传输;半径为10 cm时,弯曲损耗小于0.01 dB/m,具有良好的低弯曲损耗特性.此光纤能够提高光纤热损伤阈值,减少接续损耗,全固态结构有效避免了空气孔塌陷,简化制备工艺,对高功率激光传输、光纤激光器和光纤放大器的发展具有重要意义.     

Fiber-optic ring-down spectroscopy using a tunable picosecond gain-switched diode laser

Visible and near-infrared laser light pulses were coupled into two different types of optical fiber cavities. One cavity consisted of a short strand of fiber waveguide that contained two identical fiber Bragg gratings. Another cavity was made using a loop of optical fiber. In either cavity ∼40 ps laser pulses, which were generated using a custom-built gain-switched diode laser, circulated for a large number of round trips. The optical loss of either cavity was determined from the ring-down times. Cavity ring-down spectroscopy was performed on 200 pL volumes of liquid samples that were injected into the cavities using a 100 μm gap in the fiber loop. A detection limit of 20 ppm of methylene blue dye in aqueous solution, corresponding to a minimum absorptivity of εC<6 cm^-1, was realized. PACS 42.62.Fi; 42.81.-i     

利用光纤激光器光谱边带效应测量光纤色散

基于被动锁模光纤激光器中色散波与孤子波的相瓦干涉产生的光谱边带效应,提出了一种测量单模光纤色散系数的方法.测量了各级边带中心波长的偏移量,利用边带偏移量与腔内总色散之间的关系,得到腔内总色散值.不同长度的同种光纤构成的环形腔,其总色散值不同,它与光纤长度的变化斜率即是待测光纤的色散系数.搭建了被动锁模掺铒光纤激光器平台,在1560 mm波段测量了G.652常规单模光纤的色散系数,实验值为16 ps/(mm·km),与典型值17 ps/(nm·km)符合得很好.     

A high-stability semiconductor laser system for a <Superscript>88</Superscript>Sr-based optical lattice clock

We describe a frequency-stabilized diode laser at 698 nm used for high-resolution spectroscopy of the ¹S₀–³P₀ strontium clock transition. For the laser stabilization we use state-of-the-art symmetrically suspended optical cavities optimized for very low thermal noise at room temperature. Two-stage frequency stabilization to high-finesse optical cavities results in measured laser frequency noise about a factor of three above the cavity thermal noise between 2 Hz and 11 Hz. With this system, we demonstrate high-resolution remote spectroscopy on the ⁸⁸Sr clock transition by transferring the laser output over a phase noise-compensated 200-m-long fiber link between two separated laboratories. Our dedicated fiber link ensures a transfer of the optical carrier with frequency stability of 7×10⁻¹⁸ after 100 s integration time, which could enable the observation of the strontium clock transition with an atomic Q of 10¹⁴. Furthermore, with an eye toward the development of transportable optical clocks, we investigate how the complete laser system (laser+optics+cavity) can be influenced by environmental disturbances in terms of both short- and long-term frequency stability.     

A new design of low-loss and ultra-flat zero dispersion photonic crystal fiber using hollow ring defect

New hollow ring defect structure is introduced in photonic crystal fiber design for ultra- flat zero dispersion with very low waveguide losses. The hollow ring defect consisted of a central hole surrounded by a doped silica ring provides highly flexible defect engineering capabilities in photonic crystal fibers to achieve precise control of dispersion value and dispersion slope while independently maintaining low waveguide losses, which was not attainable in previous designs. A nearly flat zero dispersion of D=0±0.51 ps/nm km was obtained in the wavelength range of 1.44–1.61 μm with the maximum slope of ?2.7×10^?2 ps/nm² km. The confinement loss was less than 5.75×10^?8 dB/m along with the bending loss of 2.8×10^?6 dB/m for the radius of 10 mm, and splice loss of less than 1.57 dB to conventional single mode fiber at 1.55 μm.     

Chromatic and opto-mechanical dispersion of some characteristic parameters of optical fiber undergoing macrobending

Bending of optical fiber leads to an induced-anisotropy in the index profile that influences many important guiding fiber parameters. An analytical method is described for the measurement of refractive-index-wavelength dispersion in bent optical fibers. Multiple-beam Fizeau fringes technique at transmission is used to analyze the opto-mechanical properties and induced-index anisotropy in a standard single-mode fiber undergoes pure mechanical macrobending. The shift in Fizeau fringes is employed to evaluate the dispersion of the cladding material of the bent fiber. The radial variations in Cauchy’s coefficients and the associated variations of some fiber parameters due to macrobending are carried out. The radial profiles of some material parameters such as oscillation energy, dispersion energy, lattice energy and material dispersion are measured as well. The presented method is capable to achieve quantitative and qualitative measurements, which is not available with other methods. The method has a good index resolution in the order of 10⁻⁴ and spatial resolution of 1.3 μm.     

Investigation on an evanescent wave fiber-optic absorption sensor based on fiber loop cavity ring-down spectroscopy

An improved ring-down measurement principle for optical waveguides is presented. Fiber loop ring-down spectroscopy allows for measurement of minute optical losses in high-finesse fiber-optic cavities and immunity to the fluctuation of laser source. The evanescent wave absorption losses dependent on the absorption and the refractive index of ambient solution have been theoretically analyzed. The complex refractive index is introduced into our model and extinction coefficient can be calculated accurately through finite element analysis by setting the boundaries of the fiber and the ambient conditions. Using this method, the refractive index of environment can be taken into consideration. Our principle is validated by the highly-sensitive measurement of evanescent wave absorption loss. By chemically processing the surface of sensing segment along an extending ring-down cavity, the concentration of small volume Diethyl Sulphoxide solution where the etched fiber immersed into has been successfully measured and discussed.     

光子晶体光纤弯曲损耗特性研究

对光子晶体光纤的损耗特性进行了分析，并在实验上对两种典型的光子带隙型和全内反射型光子晶体光纤进行了研究.分别对两种不同结构的光子晶体光纤在弯曲半径2~15 mm范围内的损耗进行了测量.与传统光纤损耗实验结果的对比表明，两种光子晶体光纤的弯曲损耗均不明显，具有很强的抗弯曲损耗能力.实验也证实了光子晶体光纤弯曲损耗存在临界弯曲半径，在大于临界半径的情况下，几乎没有弯曲损耗.从结构上分析并证明光子晶体光纤弯曲损耗随填充比(d/Λ)的增加而减小，填充比越高弯曲损耗越小.     

Broadband 2 μm emission and energy-transfer properties of thulium-doped oxyfluoride germanate glass fiber

High near-infrared transparency Tm³⁺-doped germanate bulk glass and fiber have been fabricated and 2 μm emission properties demonstrated. Energy-transfer processes in the germanate glass and fiber are discussed. The emission spectra are obtained from both bulk glass and fiber with the excitation of a 794 nm laser diode. The results indicate that the line width of the Tm³⁺:³F₄→³H₆ emission spectra measured in fibers is narrower than that of the bulk glass sample and shifts to longer wavelengths with increment of fiber length. The extended overlap integral method is used to calculate the microparameters of energy transfer and critical distance. A model is derived to better understand of the energy-transfer process of thulium ions in the germanate glasses responsible for emission at 2 μm. The study indicates that Tm³⁺-doped germanate fibers with a large core diameter has proved to be promising infrared optical and high-power level laser materials.     

Predicting the performance data for a fiber laser by measuring the emitted fluorescence power of the end-on pumped fiber

Abstract

A novel method is described that enables the prediction of the main laser parameters (threshold pump power, output power, slope- and extraction efficiency) without having realized the laser itself. The emitted fluorescence power of an end-on pumped fiber is absolutely measured along the fiber. Using specific material parameters of the doped glass and the waveguide attenuation, we calculate the laser properties without taking the resonator losses into account. This approach is extremely useful for fibers with special design parameters. We have used this method to characterize a fiber with a novel design, the M-profile fiber. Combining the results with the measurements on the realized laser, the impact of resonator losses (e.g., tilted fiber endfaces, effects of butt-coupled mirrors) can be inferred and improvements can be undertaken.