Stabilization of carbon dioxide-in-water emulsions with silica nanoparticles

Stable carbon dioxide-in-water emulsions were formed with silica nanoparticles adsorbed at the interface. The emulsion stability and droplet size were characterized with optical microscopy, turbidimetry, and measurements of creaming rates. The increase in the emulsion stability as the silica particle hydrophilicity was decreased from 100% SiOH to 76% SiOH is described in terms of the contact angles and the resulting energies of attachment for the silica particles at the water-CO(2) interface. The emulsion stability also increased with an increase in the particle concentration, CO(2) density, and shear rate. The dominant destabilization mechanism was creaming, whereas flocculation, coalescence, and Ostwald ripening played only a minor role over the CO(2) densities investigated. The ability to stabilize these emulsions with solid particles at CO(2) densities as low as 0.739 g/mL is particularly relevant in practical applications, given the difficulty in stabilizing these emulsions with surfactants, because of the unusually weak solvation of the surfactant tails by CO(2).     

Oil-in-water Pickering emulsion destabilisation at low particle concentrations

Droplet evolution in unstable, dilute oil-in-water Pickering emulsions was characterised using a combination of light scattering, confocal microscopy and rheology. Emulsions were formed at concentrations of silanised fumed silica particles that are not sufficient to prevent destabilisation. The key result is that destabilisation initially occurs via a combination of droplet flocculation and permeation. Close contact between the drops enhances oil transfer from smaller drops to the larger ones. The large drops swell over time until the attached particle density is insufficient to protect the drops against coalescence. Examination of the emulsion microstructure revealed the relationship between drop stability and the structural characteristics of the aggregates formed due to coagulation of the silica particles in the emulsions. The implications of these results for controlling Pickering emulsion stability are discussed.     

Synergistic stabilization of emulsions by a mixture of surface-active nanoparticles and surfactant

The stability and rheology of tricaprylin oil-in-water emulsions containing a mixture of surface-active hydrophilic silica nanoparticles and pure nonionic surfactant molecules are reported and compared with those of emulsions stabilized by each emulsifier alone. The importance of the preparation protocol is highlighted. Addition of particles to a surfactant-stabilized emulsion results in the appearance of a small population of large drops due to coalescence, possibly by bridging of adsorbed particles. Addition of surfactant to a particle-stabilized emulsion surprisingly led to increased coalescence too, although the resistance to creaming increased mainly due to an increase in viscosity. Simultaneous emulsification of particles and surfactant led to synergistic stabilization at intermediate concentrations of surfactant; emulsions completely stable to both creaming and coalescence exist at low overall emulsifier concentration. Using the adsorption isotherm of surfactant on particles and the viscosity and optical density of aqueous particle dispersions, we show that the most stable emulsions are formed from dispersions of flocculated, partially hydrophobic particles. From equilibrium contact angle and oil-water interfacial tension measurements, the calculated free energy of adsorption E of a silica particle to the oil-water interface passes through a maximum with respect to surfactant concentration, in line with the emulsion stability optimum. This results from a competition between the influence of particle hydrophobicity and interfacial tension on the magnitude of E.     

Concentrated CO(2)-in-Water Emulsions with Nonionic Polymeric Surfactants

Concentrated CO(2)-in-water (C/W) emulsions are reported for amphiphiles containing alkylene oxide-, siloxane-, and fluorocarbon-based tails as a function of temperature and salinity. Poly(ethylene oxide)-b-poly(butylene oxide) (EO(15)-b-BO(12)) can emulsify up to 70% CO(2) with droplet sizes from 2 to 4 &mgr;m in diameter, as determined by video-enhanced microscopy. This emulsion is stable over 48 h against both flocculation and coalescence. In contrast, it is extremely difficult to form concentrated water-in-CO(2) (W/C) emulsions with surfactants containing alkylene oxide moieties due to limited solvation of such tails by CO(2). In several cases, C/W emulsions are formed even when the surfactant prefers CO(2). This violation of Bancroft's rule may be attributed in part to the low viscosity of the compressed CO(2), which governs several mass and momentum transport mechanisms relevant to emulsion formation and stabilization. For the first time, W/C microemulsions are observed in a system with a nonionic amphiphile, namely F(CF(2)CF(2))(3-8)CH(2)CH(2)O(CH(2)CH(2)O)(10-15)H. For the same system, the emulsion morphology changes from C/W to W/C as the temperature increases. The electrical conductivity of C/W emulsions is predicted successfully as a function of the dispersed phase volume fraction of CO(2) with Maxwell's theory for inhomogeneous systems. Copyright 2001 Academic Press.     

SiO2纳米颗粒与聚氧乙烯对Pickering乳液的协同稳定作用简

研究了聚氧乙烯(PEO)与SiO2纳米颗粒对水/二甲苯体系Pickering乳液的协同稳定作用. 实验发现,PEO的存在减小了乳液液滴的平均直径,抑制了乳液的相反转,有效阻止了乳液的熟化,使乳液具有更好的稳定性. 进一步对纳米颗粒膜的流变性质进行研究,结果表明,PEO高分子促进了纳米颗粒形成更大尺寸的聚集结构,提高了其在界面上的吸附性,增强了颗粒膜的力学性能,在较小颗粒用量条件下使得Gibbs稳定性判据得到满足.     

Inversion of particle-stabilized emulsions of partially miscible liquids by mild drying of modified silica particles

Using a system of modified silica particles and mixtures of water and 2,6-lutidine to form particle-stabilized emulsions, we show that subtle alterations to the hydration of the particle surface can cause major shifts in emulsion structure. We use fluorescence confocal microscopy, solid state nuclear magnetic resonance (NMR) and thermo-gravimetric analysis (TGA) to explore this sensitivity, along with other shifts caused by modifications to the silica surface chemistry. The silica particles are prepared by a variant of the St?ber procedure and are modified by the inclusion of 3-(aminopropyl)triethoxysilane and the dye fluorescein isothiocyanate. Treatment prior to emulsification consists of gently drying the particles under carefully controlled conditions. In mixtures of water and 2,6-lutidine of critical composition, the particles stabilize droplet emulsions and bijels. Decreasing particle hydration yields an inversion of the emulsions from lutidine-in-water (L/W) to water-in-lutidine (W/L), with bijels forming around inversion. So dependent is the emulsion behavior on particle hydration that microscopic differences in drying within a particle sample can cause differences in the wetting behavior of that sample, which helps to stabilize multiple emulsions. The formation of bijels at emulsion inversion is also crucially dependent on the surface modification of the silica.     

Effect of silica particles on stability of highly concentrated water-in-oil emulsions with non-ionic surfactant

Water-in-oil, high internal phase emulsion made of super-cooled aqueous solution containing a mixture of inorganic salts and stabilized with non-ionic surfactant (sorbitan monooleate) alone was investigated. It was not possible to produce a highly concentrated emulsion (with aqueous phase fraction = 94 wt %), stabilized with surface-treated silica, solely: we were able to form an emulsion with a maximal aqueous phase mass fraction of 85 wt % (emulsion inverts/breaks above this concentration). The inversion point is dependent on the silica particle concentration, presence of salt in the aqueous phase, and does not depend on the pH of the dispersed phase. All emulsions stabilized by the nanoparticles solely were unstable to shear. So, the rheological properties and stability of the emulsions containing super-cooled dispersed phase, with regards to crystallization, were determined for an emulsion stabilized by non-ionic surfactant only. The results were compared to the properties obtained for emulsions stabilized by surface treated (relatively hydrophobic) silica nanoparticles as a co-surfactant to sorbitan monooleate. The influence of the particle concentration, type of silica surface treatment, particle/surfactant ratio on emulsification and emulsion rheological properties was studied. The presence of the particles as a co-stabilizer increases the stability of all emulsions. Also, it was found that the particle/surfactant ratio is important since the most stable emulsions are those where particles dominate over the surfactant, when the surfactant’s role is to create bridging flocculation of the particles. The combination of the two types of hydrophobic silica particles as co-surfactants is: one that resides at the water/oil interface and provides a steric boundary and another that remains in the oil phase creating a 3D-network throughout the oil phase, which is even more beneficiary in terms of the emulsion stability.     

Behaviour of formula emulsions containing hydrolysed whey protein and various lecithins

Formula emulsion systems are used as enteral, sports and health products. In some formulas addition of hydrolysed protein is necessary to guarantee ease of digestion and hypoallergenicity. In the low fat emulsion model an increase in the content of lecithin (phospholipid mixture) was required, in consideration of the advice of the Food and Nutrition Board (USA) for choline supplementation. The individual and interactive effects of whey protein isolate (WPI) or hydrolysate (WPH) (3.7 and 4.9% w/w), unmodified deoiled or hydrolysed lecithin (0.48 or 0.7% w/w) and carbohydrate in the form of maltodextrin with dextrose equivalent (DE) 18.5 or glucose syrup with DE 34 (11% w/w) on the properties of formula emulsions with 4% v/w sunflower oil, were investigated using a full factorial design. The emulsions were characterised by particle size distribution, coalescence stability, creaming rate, and also surface protein and lecithin concentration. WPI-containing emulsions proved to be stable against coalescence and showed only little creaming after 1 and 7 days standing. There was a significant increase in the mean droplet size and a significant deterioration of coalescence and creaming stability when WPH instead of WPI was used as the protein source, due to the lower number of large peptides and lower surface activity of the WPH. Increasing the WPH concentration led to an increase in oil droplet size and further deterioration of the stability of the emulsions. The starch hydrolysate and lecithin also significantly influenced the emulsion properties. Their influence was less strong when the emulsion contained WPI. Under the conditions used WPH-based emulsions were more stable, in terms of creaming and coalescence, when a low level of protein was used in conjunction with hydrolysed lecithin and glucose syrup. Oil droplets in emulsions containing unmodified lecithin in either the continuous or disperse phase and WPH in the continuous phase were very sensitive to coalescence. The addition of starch hydrolysates (DE 18.5) induced intensive flocculation and phase separation in these emulsions.     

Effect of adding anionic surfactant on the stability of Pickering emulsions

We investigated the structure and stability of dodecane-in-water emulsions stabilised by partially hydrophobised silica particles after dilution of the emulsions in solutions of sodium dodecyl sulfate and sodium chloride. The emulsions were stable to coalescence on dilution in salt solutions, but did cream over time. The rate and extent of creaming gradually decreased as the salt concentration in the diluted emulsion increased. Dilution in low concentrations of the anionic surfactant did not affect the emulsion stability to coalescence or alter the creaming behaviour of the emulsion. At surfactant concentrations above the critical micelle concentration, however, the rate and extent of creaming and flocculation of the drops were enhanced.     

Particle self-assembly in oil-in-ionic liquid Pickering emulsions

We have studied polydimethylsiloxane (PDMS)-in-1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF(6)]) Pickering emulsions stabilized by polystyrene microparticles with different surface chemistry. Surprisingly, in contrast to the consensus originating from oil/water Pickering emulsions in which the solid particles equilibrate at the oil-water droplet interfaces and provide effective stabilization, here the polystyrene microparticles treated with sulfate, aldehyde sulfate, or carboxylate dissociable groups mostly formed monolayer bridges among the oil droplets rather than residing at the oil-ionic liquid interfaces. The bridge formation inhibited individual droplet-droplet coalescence; however, due to low density and large volume (thus the buoyant effect), the aggregated oil droplets actually promoted oil/ionic liquid phase separation and distressed emulsion stability. Systems with binary heterogeneous polystyrene microparticles exhibited similar, even enhanced (in terms of surface chemistry dependence), bridging phenomenon in the PDMS-in-[BMIM][PF(6)] Pickering emulsions.     

Effect of Emulsifier Type on the Characterization of O/W Emulsions Using a Spectroscopy Technique

The droplet size distribution (DSD) of emulsions is the result of two competitive effects that take place during emulsification process, i.e., drop breakup and drop coalescence, and it is influenced by the formulation and composition variables, i.e., nature and amount of emulsifier, mixing characteristics, and emulsion preparation, all of which affect the emulsion stability. The aim of this study is to characterize oil-in-water (O/W) emulsions (droplet size and stability) in terms of surfactant concentration and surfactant composition (sodium dodecyl benzene sulphonate (SDBS)/Tween 80 mixture). Ultraviolet-visible (UV-vis) transmission spectroscopy has been applied to obtain droplet size and stability of the emulsions and the verification of emulsion stability with the relative cleared volume technique (time required for a certain amount of emulsion to separate as a cleared phase). It is demonstrated that the DSD of the emulsions is a function of the oil concentration and the surfactant composition with higher stability for emulsions prepared with higher SDBS ratio and lower relative cleared volume with the time. Results also show that smaller oil droplets are generated with increasing Tween 80 ratio and emulsifier concentration.     

Novel stabilization of emulsions via the heteroaggregation of nanoparticles

The stabilization of emulsions by a mixture of oppositely charged nanoparticles is investigated in relation to their behavior in water before emulsification. No emulsion can be prepared using either negatively or positively charged silica particles alone because the particles are too hydrophilic. Certain mixtures of the two particle types lead to heteroaggregation and a lowering of the net charge. Such mixtures, of increased hydrophobicity as verified by contact angle measurements, are capable of forming stable oil-in-water emulsions of excellent coalescence stability. The increased viscosity of the continuous phase also contributes to such stability.     

Effect of electrolyte in silicone oil-in-water emulsions stabilised by fumed silica particles

Partially hydrophobised fumed silica particles are used to make silicone oil-in-water emulsions at natural pH of the aqueous phase. The stability and rheological properties of the emulsions and suspensions are studied at NaCl concentrations in the range 0-100 mM. It is found that all emulsions are very stable to coalescence irrespective of the NaCl concentration. However, a strong effect of electrolyte on the creaming and rheological properties is observed and linked to the particle interactions in aqueous suspensions. The creaming rate and extent are large at low electrolyte concentrations but both abruptly decrease at salt concentrations exceeding the critical flocculation concentration of the suspension (approximately 1 mM NaCl). The drastic improvement of the stability to creaming is attributed to the formation of a visco-elastic three-dimensional network of interconnected particles and emulsion droplets.     

A Videomicroscopic Investigation of Coupled Reversible Flocculation and Coalescence at Singlet-Doublet Equilibrium in an O/W Emulsion of Low Density Contrast

Video enhanced microscopy (VEM) enables direct investigation of dilute emulsions. A practical and effective preparative technique utilizes microslides, which are flat, rectangular microcapillaries made from borosilicate glass. Experimental difficulties due to droplet sedimentation and droplet-microslide wall interaction can be drastically reduced, even eliminated, by the use of low density contrast emulsions, i.e. emulsions where the densities of the dispersed and continuous phases are not very different. The dichlorodecane (DCD)-in-water emulsion is an example of such a system. This system.can as such be used for measurement of the time of the elementary act of coalescence, calculated from the evolution in the droplet size distribution. The developing distributions can be determined through automated VEM.

In this paper we discuss the perspective for elaboration of a standard method for the determination of an averaged time for the elementary act of coalescence. The experimental basis is automated measurement of the time dependence of the droplet size distribution, as applied to dilute DCD/w emulsions at singlet-doublet equilibrium.     

Flocculation and Coalescence of Oil-in-Water Poly(dimethylsiloxane) Emulsions

The stability of poly(dimethylsiloxane) (PDMS) oil-in-water emulsions has been investigated in the presence of added NaCl as well as in the presence of added surfactant. The emulsions were prepared using a combination of nonionic (C(x)E(y), x and y represent the number of methylene (C) and ethylene oxide (E) groups, respectively) and cationic (quarternary alkylammonium) surfactants. The droplets were observed to exhibit weak flocculation in the presence of high NaCl concentration (1 M). Phase separation and optical microscopic observations revealed that the principal mechanism for emulsion destabilization at high salt concentration was coalescence, which was accelerated at elevated temperature (50 degrees C). The effective coalescence rate for diluted emulsions was investigated using photon correlation spectroscopy. The small effective Hamaker constant for PDMS is the primary reason for the slow rate of coalescence observed for the emulsions at neutral pH in the presence of NaCl. The stability of PDMS emulsions to flocculation is qualitatively similar to that reported for low Hamaker constant dispersions (e.g., microgel particles). Addition of cationic surfactants (cetyltrimethylammonium chloride and dodecyl dimethylbenzylammonium chloride) to the negatively charged droplets after preparation was shown to decrease the emulsion stability once the surfactant concentration exceeded the CMC. Electrophoretic mobility measurements showed that added cationic surfactant changed the sign of the droplet charge from negative to positive at concentrations well below the CMC. Charged micelles of the same sign as the droplets are electrostatically excluded from close approach to the droplet surface within a distance (varepsilon) which results in depletion flocculation. Copyright 2000 Academic Press.     

Fat crystals and water-in-oil emulsion stability

Products such as cosmetics, pharmaceuticals, and crude oil often exist as water-in-oil (W/O) emulsions during their processing or in final form. In many cases, their dispersed aqueous phase is encased in a crystal network and/or by interfacially-adsorbed (‘Pickering’) particles [paraffins, triacylglycerols, polymers, etc.] that promote emulsion kinetic stability by hindering droplet–droplet contact, coalescence and macroscopic phase separation. In processed foods, important questions remain regarding whether a continuous phase fat crystal network or Pickering crystal provides better stabilization. This review explores the following factors related to crystal-stabilized W/O emulsions: i) the key properties dictating fat crystal spatial distribution (at the interface or in the continuous phase); ii) how temperature and freeze–thaw emulsion destabilization are intimately linked with fat crystal spatial distribution, and; iii) why oil-soluble surfactant interactions with the continuous oil phase influence fat crystal wettability and emulsifier efficacy. It is shown that these parameters strongly govern W/O emulsion formation and stability.     

Comparison of Pickering and network stabilization in water-in-oil emulsions

We compared the efficacy of Pickering crystals, a continuous phase crystal network, and a combination thereof against sedimentation and dispersed phase coalescence in water-in-oil (W/O) emulsions. Using 20 wt % water-in-canola oil emulsions as our model, glycerol monostearate (GMS) permitted Pickering-type stabilization, whereas simultaneous usage of hydrogenated canola oil (HCO) and glycerol monooleate (GMO) primarily led to network-stabilized emulsions. A minimum of 4 wt % GMS or 10 wt % HCO was required for long-term sedimentation stability. Although there were no significant differences between the two in mean droplet size with time, the free water content of the network-stabilized emulsions was higher than Pickering-stabilized emulsions, suggesting higher instability. Microscopy revealed the presence of crystal shells around the dispersed phase in the GMS-stabilized emulsions, whereas in the HCO-stabilized emulsion, spherulitic growth in the continuous phase and on the droplet surface occurred. The displacement energy (E(disp)) to detach crystals from the oil-water interface was ～10(4) kT, and was highest for GMS crystals. Thermal cycling to induce dispersed phase coalescence of the emulsions resulted in desorption of both GMS and GMO from the interface, which we ascribed to solute-solvent hydrogen bonding between the emulsifier molecules and the solvent oil, based on IR spectra. Overall, Pickering crystals were more effective than network crystals for emulsion stabilization. However, the thermal stability of all emulsions was hampered by the diffusion of the molten emulsifiers from the interface.     

Influence of nanoscale particle roughness on the stability of pickering emulsions

The wetting behavior of solid surfaces can be altered dramatically by introducing surface roughness on the nanometer scale. Some of nature's most fascinating wetting phenomena are associated with surface roughness; they have inspired both fundamental research and the adoption of surface roughness as a design parameter for man-made functional coatings. So far the attention has focused primarily on macroscopic surfaces, but one should expect the wetting properties of colloidal particles to be strongly affected by roughness, too. Particle wettability, in turn, is a key parameter for the adsorption of particles at liquid interfaces and for the industrially important use of particles as emulsion stabilizers; yet, the consequence of particle roughness for emulsion stability remains poorly understood. In order to investigate the matter systematically, we have developed a surface treatment, applicable to micrometer-sized particles and macroscopic surfaces alike, that produces surface coatings with finely tunable nanoscale roughness and identical surface chemistry. Coatings with different degrees of roughness were characterized with regard to their morphology, charging, and wetting properties, and the results were correlated with the stability of emulsions prepared with coated particles of different roughness. We find that the maximum capillary pressure, a metric of the emulsions' resistance to droplet coalescence, varies significantly and in a nonmonotonic fashion with particle roughness. Surface topography and contact angle hysteresis suggest that particle roughness benefits the stability of our emulsions as long as wetting occurs homogeneously (Wenzel regime), whereas the transition toward heterogeneous wetting (Cassie-Baxter regime) is associated with a loss of stability.     

Synergistic interaction in emulsions stabilized by a mixture of silica nanoparticles and cationic surfactant

Using a range of complementary experiments, a detailed investigation into the behavior of dodecane-water emulsions stabilized by a mixture of silica nanoparticles and pure cationic surfactant has been made. Both emulsifiers prefer to stabilize o/w emulsions. At high pH, particles are ineffective emulsifiers, whereas surfactant-stabilized emulsions become increasingly stable to coalescence with concentration. In mixtures, no emulsion phase inversion occurs although synergism between the emulsifiers leads to enhanced stability at either fixed surfactant concentration or fixed particle concentration. Emulsions are most stable under conditions where particles have negligible charge and are most flocculated. Freeze fracture scanning electron microscopy confirms the presence of particle flocs at drop interfaces. At low pH, particles and surfactant are good emulsifiers alone. Synergism is also displayed in these mixtures, with the extent of creaming being minimum when particles are most flocculated. Experiments have been undertaken in order to offer an explanation for the latter synergy. By determining the adsorption isotherm of surfactant on particles in water, we show that surfactant addition initially leads to particle flocculation followed by re-dispersion. Using suitable contact angle measurements at oil-water-solid interfaces, we show that silica surfaces initially become increasingly hydrophobic upon surfactant addition, as well as surfactant adsorption lowering the oil-water interfacial tension. A competition exists between the influence of surfactant on the contact angle and the tension in the attachment energy of a particle to the interface.     

Characterization of fluorocarbon-in-water emulsions with added triglyceride

Fluorocarbon-in-water emulsions are being explored clinically as synthetic oxygen carriers in general surgery. Stabilizing fluorocarbon emulsions against coarsening is critical in maintaining the biocompatibility of the formulation following intravenous administration. It has been purported that the addition of a small percentage of long-chain triglyceride results in stabilization of fluorocarbon emulsions via formation of a three-phase emulsion. In a three-phase emulsion, the triglyceride forms a layer around the dispersed fluorocarbon, thereby improving the adhesion of the phospholipid surfactant to the dispersed phase. In the present study, we examined the effect of triglyceride addition on the physicochemical characteristics of the resulting complex dispersion. In particular, we examined the particle composition and stability of the dispersed particles using a method which first fractionates (classifies) the different particles prior to sizing (i.e., sedimentation field-flow fractionation). It was determined that the addition of a long-chain triglyceride (soybean oil) results in oil demixing and two distinct populations of emulsion droplets. The presence of the two types of emulsion droplets is not observed via light scattering techniques, since the triglyceride droplets dominate the scattering due to a large difference in the refractive index between the particles and the medium as compared to fluorocarbon droplets. The growth of the fractionated fluorocarbon emulsion droplets was followed over time, and it was found that there was no difference in growth rates with and without added triglyceride. In contrast, addition of medium-chain-triglyceride (MCT) oils results in a single population of emulsion droplets (i.e., a three-phase emulsion). These emulsions are not stable to droplet coalescence, however, as significant penetration of MCT into the phospholipid lipid interfacial layer results in a negative increment in the monolayer spontaneous curvature, thereby favoring water-in-oil emulsions and resulting in destabilization of the emulsion to the effects of terminal heat sterilization or mechanical stress.