Thermogravimetric analysis of walnut shell as pyrolysis feedstock

Thermal degradation behavior and kinetics of a biomass waste material, namely walnut shell, were investigated by using a thermogravimetric analyzer. The desired final temperature of 800 °C was achieved at three different heating rates (2, 10, and 15 °C min^?1) under nitrogen flow (50 mL min^?1). The TG and DTG curves exhibited three distinct zones that can mainly be attributed to removal of water, decomposition of hemicellulose + cellulose, and decomposition of lignin, respectively. The kinetic parameters (activation energy, pre-exponential factor, and reaction order) of active pyrolysis zone were determined by applying Arrhenius, Coats?CRedfern, and Horowitz?CMetzger methods to TG results. The values of activation energies were found to be between 45.6 and 78.4 kJ mol^?1. There was a great agreement between the results of Arrhenius and Coats?CRedfern methods while Horowitz?CMetzger method yielded relatively higher results. The existence of kinetic compensation effect was evident.     

Thermogravimetric analyses revealed the bioenergy potential of <Emphasis Type="Italic">Eulaliopsis binata</Emphasis>

The present study was focused on the thermal degradation of Eulaliopsis binata biomass produced on a salt-affected soil without any fertilizer or pesticide applications. The plant biomass was subjected to thermal degradation experiments at three heating rates, 10, 30 and 50 K min^?1. The kinetic analyses were performed through isoconversional models of Kissinger–Akahira–Sunose and Flynn–Wall–Ozawa, followed by the calculation of thermodynamic parameters of activation. The high heating value was calculated as 15.10 MJ mol^?1. The activation energy values of the grass were shown to be ranging from 118 through 240 kJ mol^?1. Energy difference of enthalpies of activation between the reagent and the activated complex was in accordance with activation energies. Pre-exponential factors indicated the reaction to follow first-order kinetics. Gibbs free energy for the grass was measured to be ranging from 171 to 174 kJ mol^?1. Our data have shown that E. binata biomass offers remarkable potential as a low-cost biomass for bioenergy.     

Thermoanalytical and NMR investigation of NaBH<Subscript>4</Subscript> × 2H<Subscript>2</Subscript>O thermolysis process

This paper describes the thermal investigations and kinetic analysis regarding the solid-state degradation of three compounds used as mental disorder therapeutic agents (antidepressants), namely amitriptyline, desipramine and imipramine. The study was carried according to ICTAC 2000 recommendations, by using three isoconversional methods, namely Flynn–Wall–Ozawa, Kissinger–Akahira–Sunose and Friedman. The differential method of Friedman indicated multistep degradation, which was later confirmed by the nonparametric kinetic method (NPK). NPK method showed that all three tricyclic antidepressants are degraded by two processes. In terms of apparent activation energies for decomposition, the NPK method indicated 123.4 kJ mol^?1 for imipramine, 112.3 kJ mol^?1 for desipramine and 82.9 kJ mol^?1 for amitriptyline, and the results are in good agreement with the ones suggested by isoconversional methods.     

Kinetics study of geopolymerization of fly ash using isothermal conduction calorimetry

Isothermal conduction calorimetry has been used to study the reaction kinetics of early geopolymerization of fly ash. Fly ash particles were subjected to react with NaOH solution in 2:1 ratio at isothermal temperatures of 34, 39, 45, 52, and 60 °C. The reaction kinetic parameters such as activation energy, rate of reaction, and pre-exponential function were calculated using the rate of heat evolution data. It is observed that the geopolymerization reaction followed a nucleation and growth mechanism. The activation energy obtained from an Arrhenius plot was around ~100 kJ mol^?1.     

Thermal Properties of Binary Mixtures of β-Cyclodextrin with Carbamazepine Polymorphs

The thermal behaviour of binary mixtures between β-cyclodextrin (β-CD) and either carbamazepine polymorphic Form I (CBZ I), Form III (CBZ III) or dihydrate was investigated in order to assess possible interactions of CBZ solid phases with β-CD. Physical mixtures and kneaded binaries of β-CD and different CBZ crystal forms were studied by differential scanning calorimetry, thermogravimetric analysis and hot stage microscopy. The pattern of transition of CBZ Form III into Form I is strongly influenced by β-CD. The liquid-solid transition is practically absent when anhydrous CBZ/β-CD mixes are tested, as a consequence of an interaction between β-CD and liquid CBZ that hinders CBZ recrystallisation as Form I occurring after CBZ Form III melting. Water loss on heating of CBZ dihydrate in the presence of β-CD leads in all cases to the formation of CBZ Form I. This revised version was published online in August 2006 with corrections to the Cover Date.     

N,N'-二(5,5-二甲基-2-磷杂-2-硫代-1,3-二噁烷-2-基)乙二胺的热分解动力学研究

以TG-DTG为手段, 研究了N,N'-二(5,5-二甲基-2-磷杂-2-硫代-1,3-二噁烷-2-基)乙二胺(DPTDEDA)在氮气气氛中的热分解动力学, 利用 Kissinger法、Flynn-Wall-Ozawa(FWO)法对DPTDEDA进行了动力学分析, 求出了该物质的热分解动力学参数, 同时利用Satava-Sestak法研究了该物质的热分解机理. 结果表明, Kissinger法所求得的表观活化能为137.37 kJ•mol^－1, 指前因子ln A＝28.00; Flynn-Wall-Ozawa法所求得的活化能为139.83 kJ•mol^－1. DPTDEDA的热分解机理为相边界反应, 其动力学方程为G(α)＝1－(1－α)⁴, 反应级数n＝4.     

Thermal degradation of a composite solid propellant examined by DSC

The thermal decomposition of ammonium perchlorate (AP)/hydroxyl-terminated-polybutadiene (HTPB), the AP/HTPB solid propellant, was studied at different heating rates in dynamic nitrogen atmosphere. The exothermic reaction kinetics was studied by differential scanning calorimetry (DSC) in non-isothermal conditions. The Arrhenius parameters were estimated according to the Ozawa method. The calculated activation energy was 134.5 kJ mol^-1, the pre-exponential factor, A, was 2.04×1010 min^-1 and the reaction order for the global composite decomposition was estimated in 0.7 by the kinetic Shimadzu software based on the Ozawa method. The Kissinger method for obtaining the activation energy value was also used for comparison. These results are discussed here. This revised version was published online in August 2006 with corrections to the Cover Date.     

Thermal properties and kinetics of new-generation posterior bulk fill composite cured light-emitting diodes

In this study, the thermal behavior in terms of glass transition (T _g), degradation, and thermal stability of four commercial new-generation posterior bulk fill composites (Surefill SDR, Dentsply; Quixfill, Dentsply; Xtrabase, Voco; and Xtrafill, Voco) activated by light-emitting diodes (LEDs) was analyzed by thermogravimetric analysis (TG), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). The activation energies (E _a) for the decomposition of the dental resins were calculated based on the Kissinger and Doyle kinetic models from the peaks of the endothermic curves obtained when the specimens were heated at four different temperatures (5, 10, 15, and 20 °C min^?1) during DSC. The results show that the Xtrabase composite displayed the highest T _g (120 °C at a 5 °C min^?1 heating rate) and E _a (157.64 kJ mol^?1) values associated with thermal degradation from the main chain of the polymer.     

Kinetic and thermodynamic parameters of volatilization of biodiesel from babassu, palm oil and mineral diesel by thermogravimetric analysis (TG)

The boiling point and volatility are important properties for fuels, as it is for quality control of the industry of petroleum diesel and biofuels. In addition, through the volatility is possible to predict properties, such as vapor pressure, density, latent heat, heat of vaporization, viscosity, and surface tension of biodiesel. From thermogravimetry analysis it is possible to find the kinetic parameters (activation energy, pre-exponential factor, and reaction order), of thermally simulated processes, like volatilization. With the kinetic parameters, it is possible to obtain the thermodynamic parameters by mathematical formula. For the kinetic parameters, the minor values of activation energy were found for mineral diesel (E = 49.38 kJ mol^?1), followed by babassu biodiesel (E = 76.37 kJ mol^?1), and palm biodiesel (E = 87.00 kJ mol^?1). Between the two biofuels studied, the babassu biodiesel has the higher minor value of activation energy. The thermodynamics parameters of babassu biodiesel are, ΔS = ?129.12 J mol^?1 K^?1, ΔH = +80.38 kJ mol^?1 and ΔG = +142.74 kJ mol^?1. For palm biodiesel ΔS = ?119.26 J mol^?1 K^?1, ΔH = + 90.53 kJ mol^?1 and ΔG = +141.21 kJ mol^?1, and for diesel ΔS = ?131.3 J mol^?1 K^?1, ΔH = +53.29 kJ mol^?1 and ΔG = +115.13 kJ mol^?1. The kinetic thermal analysis shows that all E, ΔH, and ΔG values are positive and ΔS values are negative, consequently, all thermodynamic parameters indicate non-spontaneous processes of volatilization for all the fuels studied.     

Ti基化学镀Ni-P和Ni-P-Cg镀层晶化动力学

利用化学镀技术在Ti基体材料表面制备了Ni-P合金镀层和Ni-P-Cg复合镀层。利用SEM、XRD和EDS等分析了镀层的晶化过程,用差热分析仪研究了Ni-P合金镀层和复合镀层的晶化动力学,运用Ozawa、Freeman-Carroll、Achar和Coats-Redfern方法对非等温动力学数据进行了分析和比较。结果发现,复合镀层的特征温度T_m和晶化激活能E均高于Ni-P合金镀层,而热焓值｜ΔH｜却低于Ni-P镀层;计算出Ni-P合金镀层和Ni-P-Cg复合镀层晶化激活能分别为308.9 kJ·mol^-1和412.99 kJ·mol^-1、指前因子A分别为58.03 s^-1和77.84 s^-1,确定了Ni-P合金镀层和复合镀层晶化动力学方程。     

Thermogravimetric analysis of lignocellulosic and microalgae biomasses and their blends during combustion

Thermogravimetric analysis was used to study and compare the combustion of different blends of corn bioresidues with sunflower, rape and algae bioresidues. Non-isothermal thermogravimetric data were used to obtain the combustion kinetics of these bioresidues. This paper reports on the application of the Vyazovkin and Ozawa–Flynn–Wall isoconversional methods for the evaluation of kinetic parameters (energy activation, pre-exponential factor and order of reaction) for the combustion of the biomasses studied. Differences were found in the TG curves in accordance with the proximate analysis results for the cellulose, hemicellulose and lignin content of biomasses. The activation energy obtained from combustion (E ~ 151.6 kJ mol^?1) was lower than that from the blends (similar values were obtained for corn–sunflower, E ~ 160.5 kJ mol^?1 and corn–rape, E ~ 156.9 kJ mol^?1) whereas the activation energy obtained from the microalgae was higher (E ~ 171.5 kJ mol^?1). Both the Vyazovkin and Ozawa–Flynn–Wall methods yielded similar results.     

The mechanism and kinetics of curing reaction of AG-80/SED system by DSC

The mechanism and kinetics of curing reaction of tetrafunctional epoxy resin (Ag-80)/novel diamines curing (SED) system were studied by non-isothermal and isothermal DSC. Different equivalent ratios of amine-epoxide give rise to different curing mechanisms. The main condensation reaction can be attributed to the reactions between the primary amine and epoxide and between the hydroxyl and epoxide when temperature is below 200°C, and to the reaction between the second-ary amine and epoxide when temperature is above 200°C. The corresponding apparent activation energies are 58.3 kJ·mol^?1 and 99.3 kJ·mol^?1 respectively. Apparent activation energies of condensation reactions between primary amine and epoxide and between hydroxyl and epoxide are just the same, which are 47.3 kJ·mol^?1.     

Thermogravimetry study of the pyrolytic characteristics and kinetics of macro-algae Macrocystis pyrifera residue

Macrocystis pyrifera is one important marine macro-algae, while its residues produced by industrial alginate extraction is a hot potato. To figure out whether its residue is suitable for pyrolysis for biofuel, the pyrolytic characteristics and kinetics of macro-algae M. pyrifera residue was investigated using thermogravimetric method from 50 to 800 °C in an inert argon atmosphere at different heating rates of 5, 10, 20, and 30 °C min^?1. The activation energy and pre-exponential factor was calculated by Flynn–Wall–Ozawa, Kissinger–Akahira–Sunose, and Popescu methods, and the kinetic mechanism was deduced by Popescu method. The results showed that the primary devolatilization stage of M. pyrifera residue can be described by Jander function $ \left(\left[ {1 - \left( {1 - \alpha } \right)^{1/3} } \right]^{2}\right) $ . The average activation energy of M. pyrifera residue was 222.4 kJ mol^?1. The results suggested that the experimental results and kinetic parameters provided useful information for the design of pyrolytic processing system using M. pyrifera residue as feedstock.     

Kinetic analysis of co-pyrolysis of cellulose and polypropylene

The present research work focuses on understanding the kinetics and mechanism of co-pyrolysis of cellulose, a major constituent of biomass, and polypropylene (PP) that is abundantly present in waste plastics. Co-pyrolysis of cellulose and PP of different compositions, viz., 100:0, 80:20, 60:40, 40:60, 20:80, and 0:100 (mass%/mass%), was carried out in a thermogravimetric analyzer at various heating rates from 5 to 180 K min^?1. The kinetics of slow to medium heating rate pyrolysis was analyzed using first Kissinger and Kissinger–Akahira–Sunose techniques. Cellulose and PP decomposition occurred in two distinct temperature regimes, viz., 575–650 and 675–775 K, respectively. However, apparent activation energies of thermal decomposition of the mixtures clearly indicated the presence of interaction between cellulose and PP. The presence of cellulose in the mixture decreased the apparent activation energy of PP decomposition from 210 to 120 kJ mol^?1, while the presence of PP did not affect the apparent activation energy of cellulose decomposition (E _a = 158 ± 3 kJ mol^?1). A significant decrease in apparent activation energy was observed in the conversion regime corresponding to the completion of cellulose pyrolysis and beginning of PP pyrolysis. Differential scanning calorimetry data clearly showed the shift of exothermic char formation to higher temperatures with PP incorporation in the mixture. The presence of PP also resulted in reduction of final char content. Based on the above analyses, a new interaction step that involves a bimolecular reaction of activated PP with volatiles from cellulose pyrolysis to form interaction products and char is proposed, and the rate limiting steps for char formation are clearly identified.     

Untersuchung der Kristallisation Unterkühlter GeX2-Schmelzen (X=O,S, Se) durch DTA

GeX₂ glass (X=O, S, Se) of defined grain was investigated at constant heating rateq by applying the DTA. From the DTA-curves measured at differentq the kinetic parameters of crystallization were determined according to the Kissinger method. Under these conditions, the effective activation energies for the oxide, sulfide and selenide were found to be 179, 219 and 298 kJ·mol^?1, respectively. If bulk GeS₂ glass is used as starting material, the shape of the DTA-curves is different from the curves obtained from grainy material and they cannot be evaluated by the Kissinger procedure.     

Effects of spice extracts on lipid fraction oxidative stability of cookies investigated by DSC

The addition of natural antioxidants to the bakery products containing fats can extend their shelf life, and it may be more attractive to consumers. In this research, the antioxidant effect of spice extracts and synthetic antioxidant on oxidative stability of fat extracted from cookies was evaluated by differential scanning calorimetry (DSC). The results revealed that addition of spice extracts to the cookies in comparison to cookies without additives reduced the oxidation as evidenced by higher the onset oxidation temperature (t _ON) of antioxidant-treated samples. Using the Ozawa–Flynn–Wall method, the activation energies (E _a/kJ mol^?1) and pre-exponential factors (Z/min^?1) and then induction times (τ/min) were calculated and also used for evaluation of antioxidants efficiency. After baking, cookies were also subjected to sensory studies and to instrumental measurements of colour changes. Among the samples studied, cookies with 0.02 % of rosemary or 0.2 % thyme extracts showed good sensorial acceptability. Cookies fortified with spice extracts also characterised greater lightness compared to the control sample.     

CoC2O4·2H2O在空气中的热分解动力学研究

纳米Co3O4具有尖晶石结构,Co3 占据八面体位,具有较高的晶体场稳定化能,在空气中低于800℃时十分稳定,是优良的催化材料[1]。Co3O4还可以作为高比能锂离子电池负极材料具有非常好的电化学活性,充放电容量高达960m A h·g-1。纳米Co3O4在紫外、可见及近红外区域都有良好的吸收效果,因此,在隐身技术、保温节能技术等领域具有潜在的应用前景。所以,Co3O4超细粉体的制备和应用研究具有十分重要的意义。我们合成了草酸盐先驱物制备纳米Co3O4用作隐身材料,因此对先驱物的热分解过程研究是十分必要的。热分析方法在了解先驱物热分解反应的物理…     

Thermal study on decomposition of LiBH4 at non-isothermal and non-equilibrium conditions

Thermal decomposition measurements for lithium borohydride (LiBH₄) are performed at non-isothermal and non-equilibrium conditions by means of differential thermal analysis (DTA). A simplified alternative procedure is introduced for evaluating thermodynamic and kinetic parameters simultaneously using a single set of measurements. Rate constant (k) and enthalpy (ΔH = ?102.1 ± 0.7 kJ mol^?1 LiBH₄) are archived. Temperature dependence for activation energy (E _a) is found taking advantage of Guggenheim–Arrhenius method; the mean activation energy is $ \overline{E}_{a} $  93.9 ± 0.9 kJ mol^?1 LiBH₄ in the range of heating rate β 1–50 K min^?1.     

Investigation of thermal decomposition kinetics of taurine

The non-isothermal thermal decomposition of taurine was investigated by means of thermogravimetric analysis (TG) and differential thermal analysis (DTA). The experimental data were treated using Flynn–Wall–Ozawa, Doyle, Kissinger, and ?atava–?esták methods, respectively. The results show that the non-isothermal thermal decomposition mechanism of taurine is classified as phase boundary reaction, and the mechanism function is the Mampel Power law with n = 1. The forms of both integral and differential for the mechanism function are $ G(\alpha ) = \alpha $ and $ f(\alpha ) = 1 $ , respectively. The activation energy and the pre-exponential factor are 167.88 kJ mol^?1 and 1.82 × 10¹³min^?1, respectively.     

Synthesis, structure analysis and thermodynamics of [Ni(H2O)4(TO)2](NO3)2·2H2O (TO = 1,2,4-triazole-5-one)

A novel complex [Ni(H₂O)₄(TO)₂](NO₃)₂·2H₂O (TO = 1,2,4-triazole-5-one) was synthesized and structurally characterized by X-ray crystal diffraction analysis. The decomposition reaction kinetic of the complex was studied using TG-DTG. A multiple heating rate method was utilized to determine the apparent activation energy (E _a) and pre-exponential constant (A) of the former two decomposition stages, and the values are 109.2 kJ mol^?1, 10^13.80 s^?1; 108.0 kJ mol^?1, 10^23.23 s^?1, respectively. The critical temperature of thermal explosion, the entropy of activation (ΔS ^≠), enthalpy of activation (ΔH ^≠) and the free energy of activation (ΔG ^≠) of the initial two decomposition stages of the complex were also calculated. The standard enthalpy of formation of the new complex was determined as being ?1464.55 ± 1.70 kJ mol^?1 by a rotating-bomb calorimeter.