Probing the Electronic Structure and Photoactivation Process of Nitrogen‐Doped TiO2 Using DRS,PL, and EPR

The electronic structure and photoactivation process in N‐doped TiO₂ is investigated. Diffuse reflectance spectroscopy (DRS), photoluminescence (PL), and electron paramagnetic resonance (EPR) are employed to monitor the change of optical absorption ability and the formation of N species and defects in the heat‐ and photoinduced N‐doped TiO₂ catalyst. Under thermal treatment below 573 K in vacuum, no nitrogen dopant is removed from the doped samples but oxygen vacancies and Ti³⁺ states are formed to enhance the optical absorption in the visible‐light region, especially at wavelengths above 500 nm with increasing temperature. In the photoactivation processes of N‐doped TiO₂, the DRS absorption and PL emission in the visible spectral region of 450–700 nm increase with prolonged irradiation time. The EPR results reveal that paramagnetic nitrogen species (N_s^.), oxygen vacancies with one electron (V_o^.), and Ti³⁺ ions are produced with light irradiation and the intensity of N_s^. species is dependent on the excitation light wavelength and power. The combined characterization results confirm that the energy level of doped N species is localized above the valence band of TiO₂ corresponding to the main absorption band at 410 nm of N‐doped TiO₂, but oxygen vacancies and Ti³⁺ states as defects contribute to the visible‐light absorption above 500 nm in the overall absorption of the doped samples. Thus, a detailed picture of the electronic structure of N‐doped TiO₂ is proposed and discussed. On the other hand, the transfer of charge carriers between nitrogen species and defects is reversible on the catalyst surface. The presence of oxygen‐vacancy‐related defects leads to quenching of paramagnetic N_s^. species but they stabilize the active nitrogen species N_s^?.     

Synthesis of W‐doped TiO2 by low‐temperature hydrolysis: Effects of annealing temperature and doping content on the surface microstructure and photocatalytic activity

A series of tungsten‐doped Titania photocatalysts were synthesized using a low‐temperature method. The effects of dopant concentration and annealing temperature on the phase transitions, crystallinity, electronic, optical, and photocatalytic properties of the resulting material were studied. The X‐ray patterns revealed that the doping delays the transition of anatase to rutile to a high temperature. A new phase W_yTi_1‐yO₂ appeared for 5.00 wt% W‐TiO₂ annealed at 900 °C. Raman and diffuse reflectance UV–Vis spectroscopy showed that band gap values decreased slightly up to 700 °C. X‐ray photoelectron spectroscopy showed that surface species viz. Ti³⁺, Ti⁴⁺, O^2?, oxygen‐vacancies, and adsorbed OH groups vary depending on the preparation conditions. The photocatalytic activity was evaluated via the degradation of methylene blue using LED white light. The degradation rate was affected by the percentage of dopants. The best photocatalytic activity was achieved with the sample labeled 5.00 wt% W‐TiO₂ annealed at 700 °C.     

Understanding the synergistic effects,optical and electronic properties of ternary Fe/C/S‐doped TiO2 anatase within the DFT + U approach

Although TiO₂ is an efficient photocatalyst, its large band gap limits its photocatalytic activity only to the ultraviolet region. An experimentally synthesized ternary Fe/C/S‐doped TiO₂ anatase showed improved visible light photocatalytic activity. However, a theoretical study of the underlying mechanism of the enhanced photocatalytic activity and the interaction of ternary Fe/C/S‐doped TiO₂ has not yet been investigated. In this study, the defect formation energy, electronic structure and optical property of TiO₂ doped with Fe, C, and S are investigated in detail using the density functional theory + U method. The calculated band gap (3.21 eV) of TiO₂ anatase agree well with the experimental band gap (3.20 eV). The defect formation energy shows that the co‐ and ternary‐doped systems are thermodynamically favorable under oxygen‐rich condition. Compared to the undoped TiO₂, the absorption edge of the mono‐, co‐, and ternary‐doped TiO₂ is significantly enhanced in the visible light region. We have shown that ternary doping with C, S, and Fe induces a clean band structure without any impurity states. Moreover, the ternary Fe/C/S‐doped TiO₂ exhibit an enhanced photocatalytic activity, a smaller band gap and negative formation energy compared to the mono‐ and co‐doped systems. Moreover, the band edges of Fe/C/S‐doped TiO₂ align well with the redox potentials of water, which shows that the ternary Fe/C/S‐doped TiO₂ is promising photocatalysts to split water into hydrogen and oxygen. These findings rationalize the available experimental results and can assist the design of TiO₂‐based photocatalyst materials.     

On the Origin of the Visible‐Light Activity of Titanium Dioxide Doped with Carbonate Species

Plane‐wave‐based pseudopotential density functional theory (DFT) calculations are used to elucidate the origin of the high photocatalytic efficiency of carbonate‐doped TiO₂. Two geometrically possible doping positions are considered, including interstitial and substitutional carbon atoms on Ti sites. From the optical absorption properties calculations, we believe that the formation of carbonates after doping with interstitial carbon atoms is crucial, whereas the contribution from the cationic doping on Ti sites is negligible. The carbonate species doped TiO₂ exhibits excellent absorption in the visible‐light region of 400–800 nm, in good agreement with experimental observations. Electronic structure analysis shows that the carbonate species introduce an impurity state from Ti 3d below the conduction band. Excitations from the impurity state to the conduction band may be responsible for the high visible‐light activity of the carbon doped TiO₂ materials.     

First‐principles calculation of electronic structure of V‐doped anatase TiO2

The energetic and electronic structures of V‐doped anatase TiO₂ have been investigated systematically by the GGA+U approach, including replacement of Ti by V in the absence and presence of oxygen vacancies and the presence of an interstitial site. It was found that V should exist as a V⁴⁺ ion in the replacement of Ti in the anatase lattice, the electron transitions of which to the conduction band from V 3d states are responsible for the experimentally observed visible light absorption. The influence of V dopant concentration on the electronic and magnetic properties is also discussed, such as the influence of the U value in systems containing oxygen vacancies and spin flip phenomena for interstitial V‐doping.     

Molten‐Salt‐Mediated Synthesis of an Atomic Nickel Co‐catalyst on TiO2 for Improved Photocatalytic H2 Evolution

Atomic co‐catalysts offer high potential to improve the photocatalytic performance, of which the preparation with earth‐abundant elements is challenging. Here, a new molten salt method (MSM) is designed to prepare atomic Ni co‐catalyst on widely studied TiO₂ nanoparticles. The liquid environment and space confinement effect of the molten salt leads to atomic dispersion of Ni ions on TiO₂, while the strong polarizing force provided by the molten salt promotes formation of strong Ni?O bonds. Interestingly, Ni atoms are found to facilitate the formation of oxygen vacancies (OV) on TiO₂ during the MSM process, which benefits the charge transfer and hydrogen evolution reaction. The synergy of atomic Ni co‐catalyst and OV results in 4‐time increase in H₂ evolution rate compared to that of the Ni co‐catalyst on TiO₂ prepared by an impregnation method. This work provides a new strategy of controlling atomic co‐catalyst together with defects for efficient photocatalytic water splitting.     

Nitrogen-doped TiO<Subscript>2</Subscript> nanopowders prepared by chemical vapor synthesis: band structure and photocatalytic activity under visible light

During chemical vapor synthesis of TiO₂ nanopowders, nitrogen atoms were doped into the crystal lattice of TiO₂. The nitrogen atoms were predominantly incorporated substitutionally in the crystal lattice of TiO₂ nanopowders up to the doping level of 1.25 mol% nitrogen, whereas they were in both interstitial and substitutional sites over about 1.43 mol% nitrogen. From the photocatalytic activity of nitrogen-doped TiO₂ estimated by decomposition of methylene blue under visible light, it was found that the substitutional nitrogen anions appearing at the low level doping was beneficial to its photocatalytic activity, whereas the interstitial ones appearing at the high level doping over 1.25 mol% nitrogen were not. The improved photocatalytic activity due to the substitutionally doped nitrogen was attributed to band gap narrowing which was confirmed by the studies of XPS, near edge X-ray absorption fine structure, and UV–Vis absorption.     

Catalytic Role of TiO2 Terminal Oxygen Atoms in Liquid‐Phase Photocatalytic Reactions: Oxidation of Aromatic Compounds in Anhydrous Acetonitrile

On the basis of experiments carried out with controlled amounts of residual oxygen and water, or by using oxygen‐isotope‐labeled Ti¹⁸O₂ as the photocatalyst, we demonstrate that ¹⁸O_s atoms behave as real catalytic species in the photo‐oxidation of acetonitrile‐dissolved aromatic compounds such as benzene, phenol, and benzaldehyde with TiO₂. The experimental evidence allows a terminal‐oxygen indirect electron‐transfer (TOIET) mechanism to be proposed, which is a new pathway that involves the trapping of free photogenerated valence‐band holes at O_s species and their incorporation into the reaction products, with simultaneous generation of oxygen vacancies at the TiO₂ surface and their subsequent healing with oxygen atoms from either O₂ or H₂O molecules that are dissolved in the liquid phase. According to the TOIET mechanism, the TiO₂ surface is not considered to remain stable, but is continuously changing in the course of the photocatalytic reaction, challenging earlier interpretations of TiO₂ photocatalytic phenomena.     

Sulfur and Ti3+ co‐Doping of TiO2 Nanotubes Enhance Photocatalytic H2 Evolution Without the Use of Any co‐catalyst

TiO₂ nanotubes were successfully co‐doped with sulfur and Ti³⁺ states using a facile annealing treatment in H₂/H₂S gas mixture. The obtained nanotubes were investigated for their photocatalytic performance and characterized by SEM, XRD, XPS, EPR, IPCE, IMPS and Mott‐Schottky measurements. The synthesized co‐doped TiO₂ nanotubes show an enhanced photocatalytic hydrogen production rate compared to tubes that were treated only in pure H₂ or H₂S atmosphere—this without the presence of any co‐catalyst. It was found that sulfur in co‐doped TiO₂ exists in the form of S^2? and a small quantity of S⁴⁺/S⁶⁺, which leads to a narrowing of the band gap. However, the enhanced absorption of light in the visible range is not the key reason for the improved photocatalytic performance. We ascribe the enhanced photocatalytic activity to a synergetic effect of S mid‐gap states and disordered Ti³⁺ defects that facilitate photo generated electron transfer.     

First‐Principles Calculations on Electronic Structures of N/V‐Doped and N‐V‐Dodoped Anatase TiO2 (101) Surfaces

The energetic and electronic properties of N/V‐doped and N‐V‐codoped anatase TiO₂ (101) surfaces are investigated by first‐principles calculations, with the aim to elucidate the relationship between the electronic structure and the photocatalytic performance of N‐V‐codoped TiO₂. Several substitutional and interstitial configurations for the N and/or V impurities in the bulk phase and on the surface are studied, and the relative stability of different doping configurations is compared by the impurity formation energy. Systematic calculations reveal that N and V impurities can be encapsulated by TiO₂ to form stable structures as a result of strong N‐V interactions both in the bulk and the surface model. Through analyzing and comparing the electronic structures of different doping systems, the synergistic doping effects are discussed in detail. Based on these discussions, we suggest that N_OV_Ti codoping cannot only narrow the band gap of anatase TiO₂, but also forms impurity states, which are propitious for the separation of photoexcited electron–hole pairs. In the case of N_OV_Ti‐codoped TiO₂ (101) surfaces, this phenomenon is especially prominent. Finally, a feasible synthesis route for N_OV_Ti codoping into anatase TiO₂ is proposed.     

Bi‐, Y‐Codoped TiO2 for Carbon Dioxide Photocatalytic Reduction to Formic Acid under Visible Light Irradiation

Bi‐ and Y‐codoped TiO₂ photocatalysts were synthesized through a sol‐gel method, and they were applied in the photocatalytic reduction of CO₂ to formic acid under visible light irradiation. The results revealed that, after doping Bi and Y, the surface area of TiO₂ was increased from 5.4 to 93.1 m²/g when the mole fractions of doping Bi and Y were 1.0% and 0.5%, respectively, and the lattice structures of the photocatalysts changed and the oxygen vacancies on the surface of the photocatalysts formed, which would act as the electron capture centers and slow down the recombination of photo‐induced electron and hole. The photocurrent spectra also proved that the photocatalysts had better electronic transmission capacities. The HCOOH yield in CO₂ photocatalytic reduction was 747.82 μmol/g_cat by using 1% Bi‐0.5% Y‐TiO₂ as a photocatalyst. The HCOOH yield was 1.17 times higher than that by using 1% Bi‐TiO₂, and 2.23 times higher than that by using pure TiO₂. Furthermore, the 1% Bi‐0.5% Y‐TiO₂ showed the highest apparent quantum efficiency (AQE) of 4.45%.     

硼铈共掺杂纳米TiO2光催化降解三氯杀螨醇和菊酯类农药

采用溶胶-凝胶法在钛酸丁酯水解过程引入硼酸、硝酸铈,制备具有光催化活性的硼铈共掺杂纳米二氧化钛（TiO2）,经XRD、TEM、FT-IR、UV-Vis-DRS表征晶体结构,在日光灯照射下,光催化降解三氯杀螨醇、高氟氯氰菊酯、氟戊菊酯农药。结果表明：硼铈共掺杂的TiO2只有锐钛矿型,而纯的或掺铈的TiO2有含有锐钛矿型、金红石相和少量板钛矿型,UV-Vis-DRS测定结果表明硼铈共掺杂的TiO2禁带宽度变小,硼铈共掺杂的TiO2在可见光区吸光度高于掺杂铈和不掺杂的TiO2,在420nm~850nm有强的吸收;在同样光照下对三氯杀螨醇、高氟氯氰菊酯、氟戊菊酯的降解试验证明硼铈共掺杂纳米TiO2的光催化活性高于不掺杂或只掺杂铈的TiO2。     

Density Functional Characterization of the Electronic Structure and Visible‐Light Absorption of Cr‐Doped Anatase TiO2

To evaluate the electronic and optical properties of Cr‐doped anatase TiO₂, three possible Cr‐doped TiO₂ models, including Cr at a Ti site (model I), Cr at a Ti site with an oxygen vacancy compensation (model II), and an interstitial Cr site (model III), are studied by means of first principles density functional theory calculations. In model I, the splitting behavior of the Cr 3d states and the insulating properties are successfully depicted by the GGA+U method, from which it is proposed that Cr at a Ti site should exist as Cr⁴⁺ instead of the generally believed Cr³⁺. As a result, the electron transitions between these impurity states, the conduction band (CB), and the valence band (VB), as well as the d–d transitions between occupied and unoccupied Cr 3d states, provide a reasonable explanation for the experimentally observed major and minor absorption bands. In models II and III, the impurity states and associated optical transition processes—as well as the corresponding electron configurations—are examined.     

Highly Efficient Low‐Temperature Plasma‐Assisted Modification of TiO2 Nanosheets with Exposed {001} Facets for Enhanced Visible‐Light Photocatalytic Activity

Anatase TiO₂ nanosheets with exposed {001} facets have been controllably modified under non‐thermal dielectric barrier discharge (DBD) plasma with various working gas, including Ar, H₂, and NH₃. The obtained TiO₂ nanosheets possess a unique crystalline core/amorphous shell structure (TiO₂@TiO_2?x), which exhibit the improved visible and near‐infrared light absorption. The types of dopants (oxygen vacancy/surface Ti³⁺/substituted N) in oxygen‐deficient TiO₂ can be tuned by controlling the working gases during plasma discharge. Both surface Ti³⁺ and substituted N were doped into the lattice of TiO₂ through NH₃ plasma discharge, whereas the oxygen vacancy or Ti³⁺ (along with the oxygen vacancy) was obtained after Ar or H₂ plasma treatment. The TiO₂@TiO_2?x from NH₃ plasma with a green color shows the highest photocatalytic activity under visible‐light irradiation compared with the products from Ar plasma or H₂ plasma due to the synergistic effect of reduction and simultaneous nitridation in the NH₃ plasma.     

The preparation and characterization of La doped TiO2 nanoparticles and their photocatalytic activity

In this paper, pure and La doped TiO₂ nanoparticles with different La content were prepared by a sol-gel process using Ti (OC₄H₉)₄ as raw material, and also were characterized by XRD, TG-DTA, TEM, XPS, DRS and Photoluminescence (PL) spectra. We mainly investigated the effects of calcining temperature and La content on the properties and the photocatalytic activity for degrading phenol of as-prepared TiO₂ samples, and also discussed the relationships between PL spectra and photocatalytic activity as well as the mechanisms of La doping on TiO₂ phase transformation. The results showed that La³⁺ did not enter into the crystal lattices of TiO₂ and was uniformly dispersed onto TiO₂ as the form of La₂O₃ particles with small size, which possibly made La dopant have a great inhibition on TiO₂ phase transformation; La dopant did not give rise to a new PL signal, but it could improve the intensity of PL spectra with a appropriate La content, which was possibly attributed to the increase in the content of surface oxygen vacancies and defects after doping La; La doped TiO₂ nanoparticles calcined at 600°C exhibited higher photocatalytic activity, indicating that 600°C was an appropriate calcination temperature. The order of photocatalytic activity of La doped TiO₂ samples with different La content was as following: 1>1.5>3>0.5>5>0 mol%, which was the same as the order of their PL intensity, namely, the stronger the PL intensity, the higher the photocatalytic activity, demonstrating that there were certain relationships between PL spectra and photocatalytic activity. This could be explained by the points that PL spectra mainly resulted from surface oxygen vacancies and defects during the process of PL, while surface oxygen vacancies and defects could be favorable in capturing the photoinduced electrons during the process of photocatalytic reactions.     

Fabrication of Predominantly Mn4+‐Doped TiO2 Nanoparticles under Equilibrium Conditions and Their Application as Visible‐Light Photocatalyts

The chemical state of a transition‐metal dopant in TiO₂ can intrinsically determine the performance of the doped material in applications such as photocatalysis and photovoltaics. In this study, manganese‐doped TiO₂ is fabricated by a near‐equilibrium process, in which the TiO₂ precursor powder precipitates from a hydrothermally obtained transparent mother solution. The doping level and subsequent thermal treatment influence the morphology and crystallization of the TiO₂ samples. FTIR spectroscopy and X‐ray photoelectron spectroscopy analyses indicate that the manganese dopant is substitutionally incorporated by replacing Ti⁴⁺ cations. The absorption band edge can be gradually shifted to 1.8 eV by increasing the nominal manganese content to 10 at %. Manganese atoms doped into the titanium lattice are associated with the dominant 4+ valence oxidation state, which introduces two curved, intermediate bands within the band gap and results in a significant enhancement in photoabsorption and the quantity of photogenerated hydroxyl radicals. Additionally, the high photocatalytic performance of manganese‐doped TiO₂ is also attributed to the low oxygen content, owing to the equilibrium fabrication conditions. This work provides an important strategy to control the chemical and defect states of dopants by using an equilibrium fabrication process.     

Tuning the Surface Structure of Nitrogen‐Doped TiO2 Nanofibres—An Effective Method to Enhance Photocatalytic Activities of Visible‐Light‐Driven Green Synthesis and Degradation

Nitrogen‐doped TiO₂ nanofibres of anatase and TiO₂(B) phases were synthesised by a reaction between titanate nanofibres of a layered structure and gaseous NH₃ at 400–700 °C, following a different mechanism than that for the direct nitrogen doping from TiO₂. The surface of the N‐doped TiO₂ nanofibres can be tuned by facial calcination in air to remove the surface‐bonded N species, whereas the core remains N doped. N‐Doped TiO₂ nanofibres, only after calcination in air, became effective photocatalysts for the decomposition of sulforhodamine B under visible‐light irradiation. The surface‐oxidised surface layer was proven to be very effective for organic molecule adsorption, and the activation of oxygen molecules, whereas the remaining N‐doped interior of the fibres strongly absorbed visible light, resulting in the generation of electrons and holes. The N‐doped nanofibres were also used as supports of gold nanoparticle (Au NP) photocatalysts for visible‐light‐driven hydroamination of phenylacetylene with aniline. Phenylacetylene was activated on the N‐doped surface of the nanofibres and aniline on the Au NPs. The Au NPs adsorbed on N‐doped TiO₂(B) nanofibres exhibited much better conversion (80 % of phenylacetylene) than when adsorbed on undoped fibres (46 %) at 40 °C and 95 % of the product is the desired imine. The surface N species can prevent the adsorption of O₂ that is unfavourable for the hydroamination reaction, and thus, improve the photocatalytic activity. Removal of the surface N species resulted in a sharp decrease of the photocatalytic activity. These photocatalysts are feasible for practical applications, because they can be easily dispersed into solution and separated from a liquid by filtration, sedimentation or centrifugation due to their fibril morphology.     

Synthesis and Modification of Zn‐doped TiO2 Nanoparticles for the Photocatalytic Degradation of Tetracycline

The synthesis of Zn‐doped TiO₂ nanoparticles by solgel method was investigated in this study, as well as its modification by H₂O₂. The catalyst was characterized by transmission electron microscopy, X‐ray diffraction, Brunauer–Emmett–Teller, UV–visible reflectance spectra and X‐ray photoelectron spectroscopy (XPS). The results indicated that doping Zn into TiO₂ nanoparticles could inhibit the transformation from anatase phase to rutile phase. Zn existed as the second valence oxidation state in the Zn‐doped TiO₂. Zn‐doped TiO₂ that was synthesized by 5% Zn doping at 450°C exhibited the best photocatalytic activity. Then, the H₂O₂ modification further enhanced the photocatalytic activity. Zn doping and H₂O₂ modifying narrowed the band gap and efficiently increased the optical absorption in visible region. The optimal degradation rate of tetracycline by Zn‐doped TiO₂ and H₂O₂ modified Zn‐doped TiO₂ was 85.27% and 88.14%. Peroxide groups were detected in XPS analysis of H₂O₂ modified Zn‐doped TiO₂, favoring the adsorption of visible light. Furthermore, Zn‐doped TiO₂ modified by H₂O₂ had relatively good reusability, exhibiting a potential practical application for tetracycline's photocatalytic degradation.     

Origin of visible-light-driven photocatalysis: A comparative study on N/F-doped and N-F-codoped TiO2 powders by means of experimental characterizations and theoretical calculations

An overall comparative study was carried out on N-doped, F-doped, and N-F-codoped TiO₂ powders (NTO, FTO, NFTO) synthesized by spray pyrolysis in order to elucidate the origin of their visible-light-driven photocatalysis. The comparisons in their experimentally obtained characteristics were based on the analysis of XPS, UV-Vis, PL, NH₃-TPD and ESR spectra. The comparisons in their theoretically predicted properties were based on the analysis of the calculated electronic structures. As the results, N-doping into TiO₂ resulted in not only the improvement in visible-light absorption but also the creation of surface oxygen vacancies. F-doping produced several beneficial effects including the creation of surface oxygen vacancies, the enhancement of surface acidity and the increase of Ti³⁺ ions. Doped N atoms formed a localized energy state above the valence band of TiO₂, whereas doped F atoms themselves had no influence on the band structure. The photocatalytic tests indicated that the NFTO demonstrated the highest visible-light activity for decompositions of both acetaldehyde and trichloroethylene. This high activity was ascribed to a synergetic consequence of several beneficial effects induced by the N-F-codoping.     

Synthesis and Studies of the Visible‐Light Photocatalytic Properties of Near‐Monodisperse Bi‐Doped TiO2 Nanospheres

Near‐monodisperse Bi‐doped anatase TiO₂ nanospheres with almost uniform diameters in the range of 117 to 87 nm were prepared simply by introducing different amounts of bismuth nitrate pentahydrate into the reaction system and subsequent calcinations. X‐ray diffraction, UV‐visible diffuse reflectance spectra, and X‐ray photoelectron spectroscopy confirm that the doped ions substitute some of the lattice titanium atoms, and furthermore, Bi³⁺ and Bi⁴⁺ ions coexist. All the Bi‐doped TiO₂ samples show much better photocatalytic activity than pure TiO₂ in the degradation of rhodamine B (RhB) under the irradiation of visible light (λ>420 nm), and, interestingly, it was found that the degradation mechanism is different from the conventional one, which has already been reported elsewhere. The detailed mechanism is discussed in this article.