Oxygen reduction reaction activity of monodispersed Pt nanoparticles-loaded carbon black catalyst prepared with a Pt carbonyl cluster anion

Pt nanoparticles-loaded carbon black (CB) was prepared from Pt carbonyl cluster complexes, and had much narrower size distribution than commercial Pt nanoparticles/CB. In the former the monodispersed Pt nanoparticles were highly dispersed on CB without aggregation even at high Pt loading of 80 wt.%. Hydrodynamic voltammograms in O₂-saturated 0.05 M H₂SO₄ solution at 30 °C showed that the onset potential of oxygen reduction reaction (ORR) current for the monodispersed Pt nanoparticles/CB electrode was more positive than that for a polycrystalline Pt electrode and similar to that for the commercial Pt nanoparticles/CB electrode. Moreover, the mass activity for ORR for the monodispersed Pt nanoparticles/CB electrode was ca. 4.9 times higher than that for the commercial Pt nanoparticles/CB electrode, clearly indicating that the control of size distribution of Pt nanoparticles is meaningful for reducing the Pt consumption.     

Graphitic C<Subscript>3</Subscript>N<Subscript>4</Subscript>@MWCNTs supported Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> as a novel electrocatalyst for the oxygen reduction reaction in zinc–air batteries

A series of catalysts (g-C₃N₄@MWCNTs/Mn₃O₄) were prepared from g-C₃N₄, MWCNTs, and Mn₃O₄ for oxygen reduction reaction (ORR) in zinc–air batteries. From the half-cell tests, the loading of 35 % Mn₃O₄ (sample GMM35) presents an excellent activity toward ORR in alkaline condition. Rotating ring-disk electrode (RRDE) studies reveal that 3.6～3.8 electrons are transferred with a H₂O₂ yield of 11.4 % at ?0.4 V. Meanwhile, the GMM35 nanocomposite exhibits the same durability as commercial 20 wt% Pt/C in alkaline condition, but it shows lower peak power density (192.4 mW cm^?2 at 229.1 mA cm^?2) and cell voltage than those with a commercial Pt/C catalyst (260.9 mW cm^?2 at 285.4 mA cm^?2).     

Electrochemical behavior of silver-impregnated Al-pillared smectite in alkaline solution

In order to enhance silver effectiveness for oxygen reduction reaction, pillared clay was used as a support for silver nanodispersion. Silver particles incorporation into pillared clay pores was attempted by impregnation/thermal degradation technique. X-ray diffraction as well as adsorption-desorption isotherms confirmed that pillaring procedure was successful. Scanning electron microscopy evidenced that a part of silver appeared outside the pillared clay cavities. Ag-pillared clay composite homogenized with 10 wt.% of nanodispersed carbon black (Vulcan), was applied on a flat glassy carbon surface and used as an electrode material. Oxygen reduction reaction was investigated in an O₂-saturated aqueous 0.1 M NaOH solution.     

Fe–N/C nanofiber electrocatalysts with improved activity and stability for oxygen reduction in alkaline and acid solutions

Fe–N/C nanofiber (Fe–N/CNF) electrocatalysts were prepared by impregnating electrospun polyacrylonitrile nanofibers with iron nitrate (Fe(NO₃)₃) solution and subsequent heat treatment, exhibiting improved activity and stability during oxygen reduction reaction (ORR) both in 0.1 M KOH (pH?=?13) and 0.5 M H₂SO₄ (pH?=?0) electrolyte solutions. Higher treatment temperature and NH₃ atmosphere were preferred by the Fe–N/CNF catalysts, and especially the concentration of Fe(NO₃)₃ solution exerted great effects on the surface morphology, structure, and thus electrocatalytic performance of the catalysts. The Fe–N/CNFs prepared using 0.5 wt% Fe(NO₃)₃ solution showed relatively higher ORR activity in alkaline and acid solutions and better stability especially in 0.5 M H₂SO₄ solution than the catalyst without Fe, probably because Fe could promote the graphitization of the polymer-converted carbon species, enhancing the resistance to electrochemical oxidation and thus the stability of the Fe–N/CNF catalysts.     

Electrochemical deposition and characterization of polyppyrrole coatings doped with nickel cobalt oxide for environmental applications

Electrochemical depositions of hybrid polypyrrole/nickel cobalt oxide (PPy/NiCoO) coatings onto ferritic stainless steel surface were carried out with different electrochemical techniques from 0.1 M pyrrole (Py) in 0.2-M oxalic acid (OA) solution and less than 150-nanometer-sized NiCoO particles. The structural properties of the composite were investigated by using different methods such as transmission electron microscopy (TEM), scanning electron microscopy (SEM) with energy-dispersive X-ray spectrometer (EDS) and Raman spectroscopy. The embedded NiCoO particles, uniformly distributed onto the surface of the PPy film, have similar oxide ratios corresponding to a mixed oxide structure. The electrochemical characterization was done using polarization curves and linear sweep voltammetry (LSV) related to oxygen reduction reaction (ORR) in alkaline solution and hydrogen peroxide as an oxygen source. Concerning the exchange current densities for ORR, the obtained values (between 1.06 and 1.45?×?10^?3 mA cm^?2 for a total amount of NiCoO of 0.1 mg cm^?2) are comparable with other polymer films with Pt.     

Electrochemical and physical characterization of Pt–Ru alloy catalyst deposited onto microporous–mesoporous carbon support derived from Mo2C at 600 °C

The electrochemical reduction of oxygen on binary Pt–Ru alloy deposited onto microporous–mesoporous carbon support was studied in 0.5 M H₂SO₄ solution using cyclic voltammetry, rotating disk electrode (RDE), and impedance method. The microporous–mesoporous carbon support C(Mo₂C) with specific surface area of 1,990 m²?g^?1 was prepared from Mo₂C at 600 °C using the chlorination method. Analysis of X-ray diffraction, photoelectron spectroscopy, and high-resolution transmission electron microscopy data confirms that the Pt–Ru alloy has been formed and the atomic fraction of Ru in the alloy was ～0.5. High cathodic oxygen reduction current densities (?160 A?m^?2 at 3,000 rev?min^?1) have been measured by the RDE method. The O₂ diffusion constant (1.9?±?0.3?×?10^?5?cm²?s^?1) and the number of electrons transferred per electroreduction of one O₂ molecule (～4), calculated from the Levich and Koutecky–Levich plots, are in agreement with literature data. Similarly to the Ru/RuO₂ system in H₂SO₄ aqueous solution, nearly capacitive behavior was observed from impedance data at very low ac frequencies, explained by slow electrical double-layer formation limited by the adsorption of reaction intermediates and products into microporous–mesoporous Pt–Ru–C(Mo₂C) catalyst. All results obtained for C(Mo₂C) and Pt–Ru–C(Mo₂C) electrodes have been compared with corresponding data for commercial carbon VULCAN® XC72 (C(Vulcan)) and Pt–Ru–C(Vulcan) electrodes processed and measured in the same experimental conditions. Higher activity for C(Mo₂C) and Pt–Ru–C(Mo₂C) has been demonstrated.     

Carbon Nanodots as Electrocatalysts towards the Oxygen Reduction Reaction

Electrocatalysts perform a key role in increasing efficiency of the oxygen reduction reaction (ORR) and as a result, efforts have been made by the scientific community to develop novel and cheap materials that have the capability to exhibit low ORR overpotentials and allow the reaction to occur via a 4 electron pathway, thereby mimicking as close as possible to traditionally utilised platinum. In that context, two different types of carbon nanodots (CNDs) with amide (CND‐CONH₂) and carboxylic (CND‐COOH) surface groups, have herein been fabricated and shown to exhibit excellent electrocatalytic activity towards the ORR in acid and basic media (0.1 M H₂SO₄ and 0.1 M KOH). CND surface modified carbon screen‐printed electrodes allow for a facile electrode modification and enabling the study of the CNDs electrocatalytic activity towards the ORR. CND‐COOH modified SPEs are found to exhibit improved ORR peak current and reduced overpotential by 21.9 % and 26.3 %, respectively compared to bare/unmodified SPEs. Additionally, 424 μg cm⁻² CND‐COOH modified SPEs in oxygenated 0.1 M KOH are found to facilitate the ORR via a near optimal 4 (3.8) electron ORR pathway. The CNDs also exhibited excellent long‐term stability and tolerance with no degradation being observed in the achievable current with the ORR current returning to the baseline level within 100 seconds of exposure to a 1.5 M solution of methanol. In summary, the CND‐COOH could be utilised as a cathodic electrode for PEMFCs offering greater stability than a commercial Pt electrode.     

Electrochemical Designing of Au/Pt Core Shell Nanoparticles as Nanostructured Catalyst with Tunable Activity for Oxygen Reduction

Au/Pt core shell nanoparticles (NPs) have been prepared via a layer‐by‐layer growth of Pt layers on Au NPs using underpotential deposition (UPD) redox replacement technique. A single UPD Cu monolayer replacement with Pt(II) yielded a uniform Pt film on Au NPs, and the shell thickness can be tuned by controlling the number of UPD redox replacement cycles. Oxygen reduction reaction (ORR) in air‐saturated 0.1 M H₂SO₄ was used to investigate the electrocatalytic behavior of the as‐prepared core shell NPs. Cyclic voltammograms of ORR show that the peak potentials shift positively from 0.32 V to 0.48 V with the number of Pt layers increasing from one to five, suggesting the electrocatalytic activity increases with increasing the thickness of Pt shell. The increase in electrocatalytic activity may originate mostly from the large decrease of electronic influence of Au cores on surface Pt atoms. Rotating ring‐disk electrode voltammetry and rotating disk electrode voltammetry demonstrate that ORR is mainly a four‐electron reduction on the as‐prepared modified electrode with 5 Pt layers and first charge transfer is the rate‐determining step.     

Fabrication of graphene-supported tetraferrocenylporphyrin electrocatalyst for oxygen reduction and its unique electrochemical response in both alkaline and acid media

A novel high-performance non-noble metal electrocatalyst for the oxygen reduction reaction (ORR) was fabricated by anchoring cobalt tetraferrocenylporphyrin (CoFcP) onto poly(sodium-p-styrenesulfonate) modified graphene (PSS-Gr) through solvothermally assisted π–π assembling method. The morphology of the assembled composite was characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The interactions between CoFcP moieties and graphene sheets were confirmed by UV–Vis absorption spectroscopy and X-ray photoelectron spectroscopy. The electrocatalytic properties of the CoFcP/PSS-Gr catalyst towards the oxygen reduction reaction were assessed using rotating disk electrode (RDE) and rotating ring-disk electrode (RRDE) measurements in both alkaline and acidic media. In addition, cyclic voltammetry and chronoamperometric measurements were utilized to evaluate the catalytic activity and stability of the CoFcP/PSS-Gr composite in alkaline solution. The results showed that CoFcP supported on graphene exhibited an outstanding electrocatalytic performance towards the ORR comparable with commercial Pt/C catalyst in alkaline media, such as high onset potential (0.889 V vs. reversible hydrogen electrode, RHE), half wave potential (0.789 V vs. RHE), better tolerance to methanol, excellent stability (84.1 %, retention after 10000 s), and efficient four-electron pathway. Moreover, the proposed hybrid presented excellent catalytic activity in terms of onset potential (0.72 V vs. RHE) and high-electron transfer number compared with Pt/C in acidic media.     

Oxygen reduction on electrodeposited silver catalysts in alkaline solution

In this study, silver was electrochemically deposited onto glassy carbon (GC) substrate using constant potential regime and tested for oxygen reduction reaction (ORR) in alkaline media. The surface morphology of Ag/GC electrodes was studied by scanning electron microscopy (SEM). It was established that after 10 s of deposition, a number of Ag nanoparticles with the size of 15 nm are produced that grow to about 45 nm after 300 s of electrodeposition. The ORR studies were conducted in 0.1 M KOH solution employing the rotating disk electrode (RDE) method. The Tafel slope at low current densities for electrodeposited silver is in the range from ?70 to ?80 mV. The RDE measurements showed that the electron transfer number (n) is 3.5 for smaller amounts of electrodeposited Ag, and it increases with increasing the loading of Ag on the GC surface. These n values suggest that the electroreduction of oxygen on Ag/GC electrodes proceeds mainly to water.     

Electrocatalytic oxidation of methanol by ZSM-5 nanozeolite-modified carbon paste electrode in alkaline medium

Development of a novel modified electrode for electrocatalytic oxidation of methanol in order to decrease overvoltage is importance. In this paper, carbon paste electrode (CPE) was modified by ZSM-5 nanozeolite. The average diameter of used nanozeolite was 97 nm. Ni²⁺ ions were incorporated to the nanozeolite by immersion of the modified electrode in a 0.1 M nickel chloride solution. Then, electrochemical studies of this electrode were performed by using cyclic voltammetry(CV) in alkaline medium. This modified electrode was used as an anode for the electrocatalytic oxidation of methanol in 0.1 M of NaOH solution. The obtained data demonstrated that ZSM-5 nanozeolite at the surface of CPE improves catalytic efficiency of the dispersed nickel ions toward methanol oxidation. The values of electron transfer coefficient, charge-transfer rate constant, and the electrode surface coverage are obtained 0.61, 0.2342 s^?1, and 4.33 × 10^?8 mol cm^?2, respectively. Also, the mean value of catalytic rate constant between the methanol and redox sites of electrode and diffusion coefficient were found to be 2.54 × 10⁴ cm³ mol^?1 s^?1 and 1.85 × 10^?8 cm² s^?1, respectively. Obtained results from both CV and chronoamperometric techniques indicated that the electrode reaction is a diffusion-controlled process.     

Magnetic N‐Enriched Fe3C/Graphitic Carbon instead of Pt as an Electrocatalyst for the Oxygen Reduction Reaction

A series of Fe₃C/C‐N_x nanoparticles (NPs) with different nitrogen content are prepared by a simple one‐pot route. In the synthetic procedure, aniline and acetonitrile are simultaneously used as the carbon and nitrogen source. The effect of calcination temperature on the structural and functional properties of the materials is investigated. Magnetic measurement shows that the sample prepared at 800 °C (Fe₃C/C‐N₈₀₀ NPs) possesses the highest M_s value of 77.2 emu g^?1. On testing as oxygen reduction reaction (ORR) catalysts, the sample prepared at 750 °C (Fe₃C/C‐N₇₅₀ NPs) shows the best ORR performance among the series, with a more positive onset potential (+0.99 V vs. RHE), higher selectivity (number of electron transfer n≈3.93), longer durability, and stronger tolerance against methanol crossover than commercial Pt/C catalysts in a 0.1 m KOH solution. Moreover, in acidic solution, the excellent ORR activity and stability are also exhibited.     

Progress on the development of uniform distributed Pd electroless based catalysts on MEA for PEMFC application

Envisaging the scale-up production of fuel cell electrodes, it was established an electrode manufacturing method that enables a uniform distribution of Pd-based catalyst over the MEA, ensuring simultaneously a low catalyst loading. The new procedure relies on the direct immobilization of the catalyst on the gas diffusion substrate by the electroless deposition after substrate activation by the electrodeposition of metal nucleus of Pd using the galvanostatic mode. The effect of the novel method on the catalyst distribution uniformity, morphology, and electrocatalytic activity towards the oxygen reduction reaction (ORR) in 0.1 M HClO₄ solution is compared to samples prepared by the conventional Sn/Pd sensitization—activation route. The performance of the PEMFC containing the same Pd load (0.09 mg cm^?2) reveals to be slightly higher on depositing the Pd nucleus by the galvanostatic electrodeposition than by the conventional sensitization/activation method. The new method opens up new approaches to extend the electroless deposition to the preparation of a wide range of alloy catalysts for the cathode and anode sides of PEMFCs.     

Kinetics of ethylene glycol electrooxidation on the noble metal-based nano-catalysts

A comparative electrooxidation of Eg in the alkaline solution was investigated over Pt, Pd and Au nanoparticle-modified carbon-ceramic electrode. The kinetic parameters of Eg oxidation, i.e., Tafel slope and activation energy (E _a), were determined on the modified electrodes. The lowest E _a value of 8.9 kJ mol^?1 was calculated on Pt|CCE. In continuation, the reaction orders with respect to the Eg and NaOH concentrations on Pd|CCE were found to be 0.4–0.2 and 0.6, respectively. An adsorption equilibrium constant (b) of 22.36 M^?1 and the adsorption Gibbs energy change (ΔG°) of ?7.7 kJ mol^?1 were obtained on Pd|CCE. The chronopotentiometry (CP) and chronoamperometry (CA) results showed that Pd|CCE and then Au|CCE have better performance stability than Pt|CCE for Eg electrooxidation. Additionally, the electrochemical impedance spectroscopy (EIS) suggested faster electron-transfer kinetics on Pt than that on the Pd and Au electrocatalysts.     

Oxygen reduction reaction on the low index planes of palladium electrodes modified with a monolayer of platinum film

Oxygen reduction reaction (ORR) has been studied on the low index planes of Pd modified with a monolayer of Pt (Pt/Pd(hkl)) in 0.1 M HClO₄ with the use of hanging meniscus rotating disk electrode. The activity for ORR on bare Pd(hkl) electrode depends on the surface structure strongly, however, voltammograms of ORR on Pt/Pd(hkl) electrodes do not depend on the crystal orientation. The specific activities of Pt/Pd(hkl) electrodes at 0.90 V (RHE) are higher than that on Pt(1 1 0) which has the highest activity for ORR in the low index planes of Pt. The mass activity on Pt/Pd(hkl) electrode is 7 times as high as a commercial Pt/C catalyst.     

Platinum nanoparticles supported on nitrobenzene-functionalised graphene nanosheets as electrocatalysts for oxygen reduction reaction in alkaline media

A systematic study on the electrocatalytic properties of Pt nanoparticles supported on nitrobenzene-modified graphene (Pt-NB/G) as catalyst for oxygen reduction reaction (ORR) in alkaline solution was performed. Graphene nanosheets were spontaneously grafted with nitrophenyl groups using 4-nitrobenzenediazonium salt. The electrocatalytic activity towards the ORR and stability of the prepared catalysts in 0.1 M KOH solution have been studied and compared with that of the commercial Pt/C catalyst. The results obtained show that the NB-modified graphene nanosheets can be good Pt catalyst support with high stability and excellent electrocatalytic properties. The specific activity of Pt-NB/G for O₂ reduction was 0.184 mA cm⁻², which is very close to that obtained for commercial 20 wt% Pt/C catalyst (0.214 mA cm⁻²) at 0.9 V vs. RHE. The Pt-NB/G hybrid material promotes a four-electron reduction of oxygen and can be used as a promising cathode catalyst in alkaline fuel cells.     

Atomically Dispersed FeN2P2 Motif with High Activity and Stability for Oxygen Reduction Reaction Over the Entire pH Range

The past decade has witnessed the great potential of Fe-based single-atom electrocatalysis in catalyzing oxygen reduction reaction (ORR). However, it remains a grand challenge to substantially improve their intrinsic activity and long-term stability in acidic electrolytes. Herein, we report a facile chemical vapor deposition strategy, by which high-density Fe atoms (3.97 wt%) are coordinated with square-planar para-positioned nitrogen and phosphorus atoms in a hierarchical carbon framework. The as-crafted atomically dispersed Fe catalyst (denoted Fe-SA/PNC) manifests an outstanding activity towards ORR over the entire pH range. Specifically, the half-wave potential of 0.92 V, 0.83 V, and 0.86 V vs. reversible hydrogen electrode (RHE) are attained in alkaline, neutral, and acidic electrolytes, respectively, representing the high performance among reported catalysts to date. Furthermore, after 30,000 durability cycles, the Fe-SA/PNC remains to be stable with no visible performance decay when tested in 0.1 M KOH and 0.5 M H₂SO₄, and only a minor negative shift of 40 mV detected in 0.1 M HClO₄, significantly outperforming commercial Pt/C counterpart. The coordination motif of Fe-SA/PNC is validated by density functional theory (DFT) calculations. This work provides atomic-level insight into improving the activity and stability of non-noble metal ORR catalysts, opening up an avenue to craft the desired single-atom electrocatalysts.     

Elucidation of the Oxygen Reduction Volcano in Alkaline Media using a Copper–Platinum(111) Alloy

The relationship between the binding of the reaction intermediates and oxygen reduction activity in alkaline media was experimentally explored. By introducing Cu into the 2nd surface layer of a Pt(111) single crystal, the surface reactivity was tuned. In both 0.1 m NaOH and 0.1 m KOH, the optimal catalyst should exhibit OH binding circa 0.1 eV weaker than Pt(111), via a Sabatier volcano; this observation suggests that the reaction is mediated via the same surface bound intermediates as in acid, in contrast to previous reports. In 0.1 m KOH, the alloy catalyst at the peak of the volcano exhibits a maximum activity of 101±8 mA cm^?2 at 0.9 V vs. a reversible hydrogen electrode (RHE). This activity constitutes a circa 60‐fold increase over Pt(111) in 0.1 m HClO₄.     

Ultra-high surface area and mesoporous N-doped carbon derived from sheep bones with high electrocatalytic performance toward the oxygen reduction reaction

A nitrogen (N)-doped mesoporous carbon material exhibiting ultra-high surface area was successfully synthesized from sheep bones via a facile and low-cost method. The obtained carbon material had an ultra-high specific surface area of 1961 m² g^?1 and provided rich active sites for the oxygen reduction reaction (ORR), which in turn resulted in high electrocatalytic activity. It was found that the pore size distribution for the newly prepared carbonaceous material fell in the range of 1–4 nm. Benefiting from its high surface area and the presence of pyridine-N and quaternary-N species, the as-prepared carbon material exhibited excellent ORR activity in an oxygen-saturated 0.1 M KOH solution, compared to commercial Pt/C (10 wt%). Due to its high ORR catalytic activity, stability and low-cost, using sheep bone as C and N precursors to produce N-doped carbon provides an encouraging step toward the goal of replacing commercial Pt/C as fuel cell cathode electrocatalyst.     

Lead-doped carbon ceramic electrode as a renewable surface composite electrode for the preparation of lead dioxide film and detection of <Emphasis Type="SmallCaps">l</Emphasis>-tyrosine

Lead-doped carbon ceramic electrode as a new type of renewable composite electrode was prepared by mixing the lead powder with electrode matrix before gelation. Pb on the electrode surface was then converted to lead dioxide by the potential scanning of the composite electrode in 0.1 M NaOH solution in the range of ? 0.3 to 0.7 V versus SCE. The composition and morphology of the electrodes were studied by energy dispersive X-ray spectrometry, scanning electron microscopy, and atomic force microscopy techniques. Cyclic voltammetry and chronoamperometry techniques were also used to study the electrocatalytic activity of the modified electrode toward the oxidation of the l-tyrosine. The best results were obtained at a working potential of 0.45 V (vs. SCE) in 0.1 M NaOH solution. The sensor exhibited a good linear response in the range of 5–1458 µM with a coefficient of determination of 0.9963. The detection limit was 0.77 µM, and sensitivity was 37.4 μA mM^?1. In addition, the modified electrode showed high stability and interference-free response for to detection of the l-tyrosine.