Simultaneous determination of selenium and lead in whole blood samples by differential pulse polarography

The polarographic reduction of lead in the presence of selenite gives rise to an additional peak corresponding to the reduction of lead (Pb) on adsorbed selenium (Se) on mercury at −0.33 V. The selenium and lead content can be determined using this peak by the addition of a known amount of one of these ions first and then the second ion. The linear domain range of lead is 5.0×10⁻⁷–2.0×10⁻⁵ M and for selenium 5.0×10⁻⁷–1.0×10⁻⁵ M. Using this method 4.90×10⁻⁷ M Se(IV) and 1.47×10⁻⁶ M Pb(II) in a synthetic sample could be determined with a relative error of +2.0% and 1.8%, respectively (n=4). A recovery test after acid digestion for a synthetic sample was 97% for selenium and 96.5% for lead. The method was applied to 1 ml of digested blood, and 328±23 μg l⁻¹ Se(IV) and 850±62 μg l⁻¹ Pb(II) could be determined with a 90% (n=5) confidence interval.     

Flow-injection chemiluminescence determination of tetracyclines with in situ electrogenerated bromine as the oxidant

By designing a novel flow-through electrolytic cell (FEC), bromine was produced near to the surface of the platinum electrode by electrochemical oxidation of acidic KBr. The fast and weak chemiluminescence signal produced by the chemical reaction of the electrogenerated bromine with H₂O₂ was greatly enhanced by tetracyclines Based on these observations, a new, sensitive and simple electrogenerated chemiluminescence (ECL) method for the determination of tetracyclines was developed. Under the optimum experimental conditions, the calibration graphs are linear over the range 3.0×10⁻⁸ to 5.0×10⁻⁵ g ml⁻¹ for tetracycline, 2.0×10⁻⁷ to 2.4×10⁻⁵ g ml⁻¹ for oxytetracycline and 1.0×10⁻⁷ to 5.0×10⁻⁵ g ml⁻¹ for chlortetracycline. The limits of detection (S/N=3) are 1.0×10⁻⁸ g ml⁻¹ for tetracycline, 7.0×10⁻⁸ g ml⁻¹ for oxytetracycline and 1.5×10⁻⁷ g ml⁻¹ for chlortetracycline. For the determination 5.0×10⁻⁷ g ml⁻¹ tetracycline, the relative standard deviation was <5%. The proposed method was used to determine tetracyclines in pharmaceutical formulations.     

Effect of presence of 18-crown-6 on the response of 1-pyrrolidine dicarbodithioate-based lead selective electrode

The lipophilic ammonium salt of 1-pyrrolidine dicarbodithioic acid (PCDT)[I] was introduced as a selective ionophore for a sensitive Pb-ion selective electrode. Also, the effect of immobilization of 18-crown-6 (CW), into the above membrane, on the electrode performance was discussed. The slope of the PCDT-based [I] electrode was (26–30 mV decade⁻¹), while it was (29-30 mV decade⁻¹) for (PCDT+CW)-based [II] electrode according to the doping time. The linear concentration ranges were (1×10⁻⁶–1×10⁻¹ M) and (5×10⁻⁵–1×10⁻¹ M) for electrode types [I] and [II] after one-day doping. The working pH ranges were (5.0–10.0) and (7.0–10.0) for electrode types [I] and [II], respectively. Most of the common cations were tested for the evaluation of the electrode selectivity with correlation to the ionic radii of the tested cations. Among them only Na⁺, Ag⁺ and Fe³⁺ were the real interference. Application of using the electrode for the determination of lead in lubrication oil samples was performed with RSD (0.86–1.03%). The obtained results were compared to those of an atomic absorption spectrophotometric method.     

Simultaneous potentiometric determination of ClO(3)(-)-ClO(2)(-) and ClO(3)(-)-HClO by flow injection analysis using Fe(III)-Fe(II) potential buffer

A rapid potentiometric flow injection technique for the simultaneous determination of oxychlorine species such as ClO₃⁻–ClO₂⁻ and ClO₃⁻–HClO has been developed, using both a redox electrode detector and a Fe(III)–Fe(II) potential buffer solution containing chloride. The analytical method is based on the detection of a large transient potential change of the redox electrode due to chlorine generated via the reaction of the oxychlorine species with chloride in the potential buffer solution. The sensitivities to HClO and ClO₂⁻ obtained by the transient potential change were enhanced 700–800-fold over that using an equilibrium potential. The detection limit of the present method for HClO and ClO₂⁻ is as low as 5×10⁻⁸ M with use of a 5×10⁻⁴ M Fe(III)–1×10⁻³ M Fe(II) buffer containing 0.3 M KCl and 0.5 M H₂SO₄. On the other hand, sensitivity to ClO₃⁻ was low when a potential buffer solution containing 0.5 M H₂SO₄ was used, but could be increased largely by increasing the acidity of the potential buffer. The detection limit for ClO₃⁻ was 2×10⁻⁶ M with the use of a 5×10⁻⁴ M Fe(III)–1×10⁻³ M Fe(II) buffer containing 0.3 M KCl and 9 M H₂SO₄. By utilizing the difference in reactivity of oxychlorine species with chloride in the potential buffer, a simultaneous determination method for a mixed solution of ClO₃⁻–ClO₂⁻ or ClO₃⁻–HClO was designed to detect, in a timely manner, a transient potential change with the use of two streams of potential buffers which contain different concentrations of sulfuric acid. Analytical concentration ranges of oxychlorine species were 2×10⁻⁵–2×10⁻⁴ M for ClO₃⁻, and 1×10⁻⁶–1×10⁻⁵ M for HClO and ClO₂⁻. The reproducibility of the present method was in the range 1.5–2.3%. The reaction mechanism for the transient potential change used in the present method is also discussed, based on the results of batchwise experiments. The simultaneous determination method was applied to the determination of oxychlorine species in a tap water sample, and was found to provide an analytical result for HClO, which was in good agreement with that obtained by the o-tolidine method and to provide a good recovery for ClO₃⁻ added to the sample.     

Determination of adenosine disodium triphosphate using prulifloxacin-terbium(III) as a fluorescence probe by spectrofluorimetry

A new spectrofluorimetric method is developed for determination of adenosine disodium triphosphate (ATP). The interactions between prulifloxacin (PUFX)–Tb³⁺ complex and adenosine disodium triphosphate has been studied by using UV–vis absorption and fluorescence spectra. Using prulifloxacin–Tb³⁺ as a fluorescence probe, under the optimum conditions, ATP can remarkably enhance the fluorescence intensity of the prulifloxacin–Tb³⁺ complex at λ = 545 nm and the enhanced fluorescence intensity is in proportion to the concentration of ATP. Optimum conditions for the determination of ATP were also investigated. The dynamic range for the determination of ATP is 4.0 × 10⁻⁷ to 2.0 × 10⁻⁵ mol L⁻¹, and the detection limit (3 σ/k) is 1.7 × 10⁻⁸ mol L⁻¹. This method is simple, practical and relatively free interference from coexisting substances and can be successfully applied to determination of ATP in real pharmaceutical samples. The mechanism of fluorescence enhancement of prulifloxacin–Tb³⁺ complex by ATP was also discussed.     

Simultaneous potentiometric and fluorimetric determination of diclofenac in a sequential injection analysis system

Two independent methods for the determination of diclofenac were simultaneously implemented in an automated analytical system, based on the concept of sequential injection analysis, providing real-time assessment of results quality. The potentiometric detection was carried out with an ion-selective electrode based on a cyclodextrin while for the fluorimetric determination the sample was previously subject to in-line irradiation with UV light. The potentiometric and photochemical-fluorimetric determinations exhibited linear working ranges of 5×10⁻⁶ to 1×10⁻² and 1×10⁻⁶ to 1×10⁻⁴ mol dm⁻³, respectively. Relative standard errors of 0.5% for the potentiometric determination and 0.6% for the photochemical-fluorimetric determination were obtained after 10 consecutive injections of a 5×10⁻⁵ mol dm⁻³ diclofenac standard solution. The sampling rate was about 32 samples h⁻¹. Both methods were applied in the analysis of pharmaceutical formulations. The quality of results obtained was evaluated by comparison to the reference method, with no statistically significant differences for a 95% confidence level.     

Sensitive determination of phenylephrine and chlorprothixene at poly(4-aminobenzene sulfonic acid) modified glassy carbon electrode

Phenylephrine (i.e. PHE) and chlorprothixene (i.e. CPT), two effective and important antipsychotic drugs with low redox activity, were found generating an irreversible anodic peak at about +0.89 V (vs. SCE) and +1.04 V in 0.05 M HAc–NaAc (pH 5.0) or NH₂CH₂COOH–HCl (pH 2.4) buffer solution at poly(4-aminobenzene sulfonic acid) modified glassy carbon electrode (i.e. poly(4-ABSA)/GC), respectively. Sensitive and quantitative measurement for them based on the anodic peaks was established under the optimum conditions. The anodic peak current was linear to PHE and CPT concentrations from 1 × 10⁻⁷ to 1.5 × 10⁻⁵ M and 2 × 10⁻⁶ to 4.5 × 10⁻⁵ M, the detection limits obtained were 1 × 10⁻⁸ and 1 × 10⁻⁷ M, separately. The modified electrode exhibited some excellent characteristics including easy regeneration, high stability, good reproducibility and selectivity. The method proposed was successfully applied to the determination of PHE and CPT in drug injections or tablets and proved to be reliable compared with ultraviolet spectrophotometry. The modified electrode was characterized by electrochemical methods.     

Cathodic adsorptive stripping voltammetric behaviour of guanine in the presence of copper at the static mercury drop electrode

The cathodic adsorptive electrochemical behavior of guanine in the presence of some metal ions at the static mercury drop electrode was investigated. A 1.0×10⁻³ mol l⁻¹ NaOH or a 2.0×10⁻² mol l⁻¹ Hepes buffer at pH 8.0 solutions were used as supporting electrolytes. The reduction peak potential for guanine was found to be around −0.15 V, which is very close to the mercury reduction wave. A new peak appears at −0.60 V in the presence of copper or at −1.05 V in the presence of zinc. A square wave voltammetric procedure for electroanalytical determination of guanine in 2.0×10⁻² mol l⁻¹ Hepes buffer at pH 8.0 containing 1.6×10⁻⁵ mol l⁻¹of copper ions, was developed. An accumulation potential of −0.15 V during 270 s for the prior adsorption of guanine at the electrode surface was used. The response of the system was found to be linear in the range of guanine concentration from 6.62×10⁻⁸ to 1.32×10⁻⁷ mol l⁻¹ and the detection limit was 7.0×10⁻⁹ mol l⁻¹. The influence of DNA bases such as adenine, cytosine and thymine was also examined. Cyclic voltammetry was used to characterize the interfacial and redox mechanism.     

Enzymatic biosensor for the electrochemical detection of 2,4-dinitrotoluene biodegradation derivatives

In this work, we demonstrate for the first time that 4-methyl-5-nitrocatechol (4M5NC) and 2,4,5-trihydroxytoluene (2,4,5-THT), two compounds obtained from the 2,4-DNT biodegradation are recognized by polyphenol oxidase as substrates. An amperometric biosensor is described for detecting these compounds and for evaluating the efficiency of the 2,4-DNT conversion into 4M5NC in the presence of bacteria able to produce the 2,4-DNT-biotransformation. The biosensor format involves the immobilization of polyphenol oxidase into a composite matrix made of glassy carbon microspheres and mineral oil. The biosensor demonstrated to be highly sensitive for the quantification of 4M5NC and 2,4,5-THT. The analytical parameters for 4M5NC are the following: sensitivity of (7.5 ± 0.1) × 10⁵ nAM⁻¹, linear range between 1.0 × 10⁻⁵ and 8.4 × 10⁻⁵ M, and detection limit of 4.7 × 10⁻⁶ M. The sensitivity for the determination of 2,4,5-THT is (6.2 ± 0.6) × 10⁶ nAM⁻¹, with a linear range between 1.0 × 10⁻⁶ and 5.8 × 10⁻⁶ M, and a detection limit of 2.0 × 10⁻⁷. Under the experimental conditions, it was possible to selectively quantify 4M5NC even in the presence of a large excess of 2,4-DNT. The suitability of the biosensor for detecting the efficiency of 2,4-DNT biotransformation into 4M5NC is demonstrated and compared with HPLC-spectrophotometric detection, with very good correlation. This biosensor holds great promise for decentralized environmental testing of 2,4-DNT.     

Enhancement effect of sodium dodecyl benzene sulfonate (SDBS) and its application into voltammetric determination of telmisartan

A sensitive and rapid electrochemical method was developed for the determination of telmisartan based on the enhancement effect of sodium dodecyl benzene sulfonate (SDBS). In 0.1 mol L⁻¹ HClO₄ and in the presence of 7.5 × 10⁻⁵ mol L⁻¹ SDBS, a well-defined and sensitive oxidation peak was observed for telmisartan at the acetylene black (AB) paste electrode. However, the oxidation peak is poor-shaped and the peak current is very low in the absence of SDBS, suggesting that SDBS shows obvious enhancement effect for the determination of telmisartan. After all the experimental parameters were optimized, a sensitive and simple electrochemical method was developed for determining telmisartan. The oxidation peak current is proportional to the concentration of telmisartan over the range from 2.5 × 10⁻⁷ to 2.0 × 10⁻⁵ mol L⁻¹. The detection limit is 7.5 × 10⁻⁸ mol L⁻¹ after 2 min of accumulation. This new voltammetric method was successfully used to detect telmisartan in drugs.     

Determination of iron(III) with salicylic acid by the fluorescence quenching method

The spectrofluorimetric determination of Fe³⁺ using salicylic acid as an emission reagent has been investigated by measuring the decrease of fluorescence intensity of salicylic acid due to the complexation of Fe³⁺–salicylic acid. An emission peak of salicylic acid, which is decreased linearly by addition of Fe³⁺, occurs at 409 nm in aqueous solution with excitation at 299 nm. The determination of the ferric ion is in the range 1×10⁻⁶–10×10⁻⁶ M Fe³⁺ (0.0558–0.558 μg/ml) and the detection limit is 5×10⁻⁸ M. The quenching effect of Fe³⁺ on the fluorescence intensity of salicylic acid may be considered on the basis of complexation between salicylic acid and Fe³⁺. The effects of foreign ions were investigated.     

Voltammetric determination of glucose based on reduction of copper(II)–glucose complex at lanthanum hydroxide nanowire modified carbon paste electrodes

A novel voltammetric method for the determination of β-d-glucose (GO) is proposed based on the reduction of Cu(II) ion in Cu(II)(NH₃)₄²⁺–GO complex at lanthanum(III) hydroxide nanowires (LNWs) modified carbon paste electrode (LNWs/CPE). In 0.1 mol L⁻¹ NH₃·H₂O–NH₄Cl (pH 9.8) buffer containing 5.0 × 10⁻⁵ mol L⁻¹ Cu(II) ion, the sensitive reduction peak of Cu(II)(NH₃)₄²⁺–GO complex was observed at −0.17 V (versus, SCE), which was mainly ascribed to both the increase of efficient electrode surface and the selective coordination of La(III) in LNW to GO. The increment of peak current obtained by deducting the reduction peak current of the Cu(II) ion from that of the Cu(II)(NH₃)₄²⁺–GO complex was rectilinear with GO concentration in the range of 8.0 × 10⁻⁷ to 2.0 × 10⁻⁵ mol L⁻¹, with a detection limit of 3.5 × 10⁻⁷ mol L⁻¹. A 500-fold of sucrose and amylam, 100-fold of ascorbic acid, 120-fold of uric acid as well as gluconic acid did not interfere with 1.0 × 10⁻⁵ mol L⁻¹ GO determination.     

Preparation of multiwall carbon nanotubes film modified electrode and its application to simultaneous determination of oxidizable amino acids in ion chromatography

A multiwall carbon nanotubes (MWNTs) film modified electrode was prepared and used as an amperometric sensor for the simultaneous determination of oxidizable amino acids including cysteine, tryptophane and tyrosine. The electrochemical behaviors of these amino acids at this modified electrode were studied by cyclic voltammetry (CV). The results indicated that the MWNTs chemically modified electrode (CME) exhibited efficient electrocatalytic activity towards the oxidation of these amino acids with relatively high sensitivity, stability and long-life. Following separation by ion chromatography (IC) with 2.0×10⁻³ mol l⁻¹ citric acid buffer solution (pH 6.5) as eluent, cysteine, tryptophane and tyrosine could be determined by the MWNTs CME successfully. Under the optimal conditions, the detection limits were 7.0×10⁻⁷ mol l⁻¹ for cysteine, 2.0×10⁻⁷ mol l⁻¹ for tryptophane and 3.5×10⁻⁷ mol l⁻¹ for tyrosine at the signal-to-noise of 3, respectively. The method was applied successfully to the determination of these substances in plasma.     

Determination of trace metoclopramide by anodic stripping voltammetry with nafion modified glassy carbon electrode

A novel method is described for determination of metoclopramide (MCP) by second-derivative adsorptive anodic stripping voltammetry with a nafion-modified electrode. The stripping peak current is proportional to the concentration of MCP over the range 1.2×10⁻⁹–4.6×10⁻⁷ M. The detection limit is 8.0×10⁻¹¹ M with 4-min accumulation. The method has been successfully applied to the determination of MCP in human serum.     

Electrochemical study and detection of perphenazine using a gold electrode modified with decanethiol SAM

A novel method for the determination of perphenazine has been developed. The method is based on the accumulation of perphenazine at a gold electrode modified with decanethiol (DEC) self-assembled monolayer (SAM) and its oxidation at about 0.6 V (vs. saturated calomel electrode (SCE)). Because some coexistent electroactives were blocked and perphenazine was selectively accumulated by the SAM, the electrode exhibited good selectivity and sensitivity. Various conditions were optimized for practical application. Under the selected conditions (i.e. 0.05 M pH 10 sodium borate buffer, accumulation time: 120 s, accumulation potential: −0.4 V, scan rate: 100 mV s⁻¹), the anodic stripping peak current was linear to perphenazine concentration in the ranges of 6×10⁻⁹–5×l0⁻⁷ and 5×10⁻⁷–5×10⁻⁶ M with correlation coefficients of 0.998 and 0.995, respectively. For a 1.0×10⁻⁶ M perphenazine solution, the relative standard deviation of peak height was 2.3% (n=8). This method was applied to the determination of perphenazine in some drugs and the recovery was 92–101%. In addition, it was found that in the presence of perphenazine, the SAM structure changed a little and more needle holes appeared. However, the SAM could recover the original form when perphenazine and its redox product were removed from the monolayer by repeatedly cycling the electrode in a blank solution for a minute. The modified electrode was characterized by alternating current impedance and electrochemical probe.     

Lead ion selective PVC membrane electrode based on 5,5'-dithiobis-(2-nitrobenzoic acid)

A PVC membrane electrode for lead ions based on 5,5′-dithiobis-(2-nitrobenzoic acid) as membrane carrier was prepared. The electrode exhibits a Nernstian response for Pb²⁺ over a wide concentration range (1.0×10⁻²–4.0×10⁻⁶ M). It has a relatively fast response time and can be used for at least 3 months without any divergence in potentials. The proposed electrode revealed good selectivities for Pb²⁺ over a wide variety of other metal ions and could be used in a pH range of 2.0–7.0. It was used as an indicator electrode in potentiometric titration of lead ions and in direct determination of lead in water samples.     

Flow-injection potentiometric determination of triiodide by plasticized poly(vinyl chloride) membrane electrodes and its application to the determination of chlorine-containing disinfectants

Plasticized poly(vinyl chloride) (PVC) membranes of different compositions were tested for use in the construction of potentiometric flow detectors for triiodide. A membrane with a 2:1 (w/w) 2-nitrophenyl octyl ether to PVC ratio was selected. The influence of thiosulphate in the carrier solution composition and of the flow-injection variables on the determination of triiodide was studied. In the selected conditions, a linear relationship between peak height and log[I₃⁻] was obtained between 5 × 10⁻⁶ and 1 × 10⁻⁴ mol l⁻¹ triiodide. Peak height relative standard deviations for 2 × 10⁻⁵ and 1 × 10⁻⁴ mol l⁻¹ triiodide were ±0.4 and ±1.8%, respectively, and sampling frequency was 80 samples per hour. The method proposed was applied satisfactorily to the iodometric determination of different chlorine-containing disinfectants, among them trichloroisocyanuric acid and dichloroisocyanurate in several types of commercial sample.     

A new flow-injection determination of glucose based on the redox reaction of hydroquinone with iron(III) in the presence of 1,10-phenanthroline

A new spectrophotometric flow-injection (FI) method is proposed for the determination of glucose based on the redox reaction of hydroquinone with iron(III). When a glucose solution containing quinone is passed through the immobilized glucose oxidase column introduced in FI system, quinone is reduced to hydroquinone by glucose. In the presence of 1,10-phenanthroline (phen), iron(III) is then quantitatively reduced by hydroquinone to iron(II) followed by the formation of iron(II)-phen complex (λ_max=510 nm). An FI peak observed at 510 nm corresponds to the concentration of glucose. The wide dynamic range for glucose was obtained in the range of 1×10⁻⁶–1×10⁻³ mol l⁻¹ at a sampling rate of 24 h⁻¹ and the detection limit (S/N=3) was 5×10⁻⁷ mol l⁻¹. Relative standard deviations were 0.78, 0.44 and 0.23% (n=5) for 5×10⁻⁶, 5×10⁻⁵ and 5×10⁻⁴ mol l⁻¹ of glucose, respectively. The proposed method was successfully applied to the determination of glucose in control blood sera, human blood plasma and wine.     

Square wave adsorptive stripping voltammetric determination of famotidine in urine

Electrochemical studies of famotidine were carried out using voltammetric techniques: cyclic voltammetry, linear sweep and square wave adsorptive stripping voltammetry. The dependence of the current on pH, buffer concentration, nature of the buffer, and scan rate was investigated. The best results for the determination of famotidine were obtained in MOPS buffer solution at pH 6.7. This electroanalytical procedure enabled to determine famotidine in the concentration range 1 × 10⁻⁹–4 × 10⁻⁸ mol L⁻¹ by linear sweep adsorptive stripping voltammetry (LS AdSV) and 5 × 10⁻¹⁰–6 × 10⁻⁸ mol L⁻¹ by square wave adsorptive stripping voltammetry (SW AdSV). Repeatability, precision and accuracy of the developed methods were checked. The detection and quantification limits were found to be 1.8 × 10⁻¹⁰ and 6.2 × 10⁻¹⁰ mol L⁻¹ for LS AdSV and 4.9 × 10⁻¹¹ and 1.6 × 10⁻¹⁰ mol L⁻¹ for SW AdSV, respectively. The method was applied for the determination of famotidine in urine.     

Electrochemical study and flow-injection amperometric detection of trace NO(2)(-) at CuPtCl(6) chemically modified electrode

A thin film of mixed-valent CuPtCl₆ is deposited on a glassy carbon electrode by continuous cyclic scanning in a solution containing 3×10⁻³ M CuCl₂+3×10⁻³ M K₂PtCl₆+1 M KCl in the potential range from 700 to −800 mV. The cyclic voltammetry is used to study the electrochemical behaviors of nitrite on CuPtCl₆/GC modified electrode and the electrode displays a good catalytic activity toward the oxidation of nitrite. The effects of the film thickness, pH, the electrode stability and precision have been evaluated. Experiments in flow-injection analysis are performed to characterize the electrode as an amperometric sensor for the detection of nitrite. The modified electrode shows a wide dynamic range, quite a low detection limit and short response time. The linear relationship between the flow-injection peak currents and the concentrations of nitrite is at a range of 1×10⁻⁷–2×10⁻³ M with a detection limit of 5×10⁻⁸ M.