Determination of dopamine in synthetic cerebrospinal fluid by SWV with a graphite–polyurethane composite electrode

This work describes an electroanalytical investigation of dopamine using cyclic voltammetry (CV) and the graphite–polyurethane composite electrode (GPU). In CV studies, well-defined redox peaks characterize the oxidation process at the GPU electrode, which is indicative of electrocatalytic effects associated with active sites on the GPU electrode surface. A new analytical methodology was developed using the GPU electrode and square wave voltammetry (SWV) in BR buffer solution (0.1 mol L^–1; pH 7.4). Analytical curves were constructed under optimized conditions (f=60s^–1, E_a=50 mV, E_I=2 mV) and detection and quantification limits of 6.4×10^–8 mol L^–1 (12.1 g L^–1) and 5.2×10^–6 mol L^–1 (0.9 mg L^–1), respectively, were achieved. The precision of the method was checked by performing ten successive measurements for a 9.9×10^–6 mol L^–1 dopamine solution. For intra-assay and inter-assay precisions, the relative standard deviations were 1.9 and 2.3%, respectively. In order to evaluate the developed methodology, the determination of dopamine was performed with good sensitivity and selectivity, without the interference of ascorbic acid in synthetic cerebrospinal fluid, which indicates that the new methodology enables reliable analysis of dopamine.     

On-line molecularly imprinted solid phase extraction for the selective spectrophotometric determination of catechol

A molecularly imprinted polymer has been synthesized for a selective on-line catechol extraction, followed by its spectrophotometric determination in guarana powder, mate tea and tap water samples. A clean-up column, containing a methacrylic polymer + C₁₈ solid phase, was also used in order to enhance selectivity. The imprinted polymer was prepared by bulk polymerization using catechol as template and 4-vinylpyridine as the functional monomer. Permanganate solution was used as spectrophotometric reagent, where Mn(VII) was reduced to Mn(II) by catechol in an acid medium, causing color loss, which was monitored at 528 nm. Physical (extraction flow rate, elution flow rate, coil length) and chemical (nature and concentration of the eluent, potassium permanganate concentration) variables were optimized, and the selectivity was appraised using three molecules (4-chloro-2-methylphenol, 2-cresol, 2-methoxyphenol) similar to catechol. These molecules did not present interference in 1:8, 1:10 and 1:10 (catechol/concomitant) proportions, respectively. The analytical calibration curve ranged from 3.0 up to 100 μmol L^− 1 (r > 0.999; seven concentrations levels, n = 3) and the limits of detection (LOD) and quantification (LOQ) were 0.8 and 2.7 μmol L^− 1, respectively. Precision, expressed as RSD, was of 3.0% (20 μmol L^− 1, n = 10), and the analytical frequency was 15 h^− 1. Accuracy was checked by the HPLC technique and the results did not present significant difference at 95% confidence levels according to the t test.     

Determination of 4-methylbenzilidene camphor in sunscreen by square wave voltammetry in media of cationic surfactant

The voltammetric behavior of 4-methylbenzelidene camphor (MBC) was studied by square wave voltammetry (SWV) using mercury electrode. The experimental condition that provided the highest peak current with the best reduction signal definition of MBC was found in Britton-Robinson buffer and cationic surfactants, cetyltrimethylammoniun bromide (CTABr). A single peak of MBC reduction was observed at − 1.21 V versus Ag/AgCl. The developed methodology was applied for determination of MBC in commercial sunscreen SPF 15, 20 and 30 and for the simultaneous determination when other protection agents were associated, such as benzophenone-3 (BENZO) and octyl methoxycinammate (OMC). Both methodologies had shown good determination values for the analyzed samples. The calculated detection limit was 2.99 × 10^− 9 mol L^− 1 and the quantification limit was 9.98 × 10^− 9 mol L^− 1.     

Development and critical comparison of greener flow procedures for nitrite determination in natural waters

Two greener procedures for flow-injection spectrophotometric determination of nitrite in natural waters were developed and critically compared. Replacement of toxic reagents, waste minimization and treatment were exploited to attend the standards of clean chemistry. The flow system was designed with solenoid micro-pumps in order to minimize reagent consumption and waste generation. The first procedure is based on the Griess diazo-coupling reaction with sulfanilamide and N-(1-naphthyl)ethylenediamine (NED) yielding an azo dye, followed by photodegradation of the low amount of waste generated based on the photo-Fenton reaction. The second procedure is based on the formation of iodine from nitrite and iodide in acid medium in order to avoid the use of toxic reagents. For Griess method, linear response was achieved up to 1.0 mg L^− 1, described by the equation A = − 0.007 + 0.460C (mg L^− 1), r = 0.999. The detection limit was estimated as 8 μg L^− 1 at the 99.7% confidence level and the coefficient of variation was 0.8% (n = 20). The sampling rate was estimated as 108 determinations per hour. The consumption of the most toxic reagent (NED) is reduced 55-fold and 20-fold in comparison to batch method and flow injection with continuous reagent addition, respectively. A colorless residue was obtained by in-line photodegradation with reduction of 87% of the total organic carbon content. The results obtained for natural water samples were in agreement with those achieved by the reference method at the 95% confidence level. For the nitrite–iodide method, linear response was observed up to 2.0 mg L^− 1, described by the equation A = − 0.024 + 0.148C (mg L^− 1), r = 0.999. The detection limit was estimated as 25 μg L^− 1 at the 99.7% confidence level and the coefficient of variation was 0.6% (n = 20). The sampling rate was estimated as 44 determinations per hour. Despite avoiding the use of toxic reagents, the nitrite–iodide method presented worst performance in terms of selectivity and sensitivity.     

Occurrence of ochratoxin A in Turkish wines

A total of 95 wine samples including 34 white, 10 rosé and 51 red wines originating from four different Turkish areas were analysed for ochratoxin A (OTA). An analytical method based on immunoaffinity column (IAC) for clean-up and high performance liquid chromatography with fluorescence detection (HPLC-FD) was used to determine OTA in wines. The limit of detection (LOD) was estimated as 0.006 ng ml^− 1 for white wine and 0.010 ng ml^− 1 for rosé and red wines. The limit of quantification (LOQ) was estimated as 0.020 ng ml^− 1 in white wine and 0.030 ng ml^− 1 in rosé and red wines. Recovery experiments were carried out with spiked samples in the range 0.1–1 ng ml^− 1 of OTA. The average OTA recoveries from spiked white wine samples varied from 79.43% to 85.07%; while the mean recoveries for rosé and red wine samples were in the range of 77.48–83.96% and 76.61–83.55%, respectively. OTA was detected in 82 (86%) wine samples at levels of < 0.006–0.815 ng ml^− 1, which were below the maximum allowable limit established by the European Community. The mean OTA concentration in red wines was slightly higher than in white and rosé wines. Furthermore, our data indicate that the geographic region of origin has strong influence on OTA level for white, rosé and red wines: wines originating from Thrace (n = 44, mean = 0.158 ng ml^− 1) and Aegean (n = 28, mean = 0.060 ng ml^− 1) regions of Turkey were more contaminated with OTA compared with wines originating from central (n = 15, mean = 0.027 ng ml⁻¹) and east Anatolia (n = 8, mean = 0.027 ng ml^− 1) areas. This study showed that the occurrence of OTA in Turkish wines is high, but at levels that probably leads to a non-significant human exposure to OTA by consumption of wines.     

Combined use of Pd and HF as chemical modifiers for the determination of total chromium in produced waters from petroleum exploration by ET AAS

This work reports the evaluation of the combined use of Pd and HF as chemical modifiers for the direct determination of total chromium in waters derived from petroleum exploration employing electrothermal atomic absorption spectrometry (ET AAS). Such waters, usually called as produced waters, have complex composition presenting a number of organic and inorganic substances. When obtained from offshore operations they also present high salinity. In order establish conditions for chromium measurement pyrolysis and atomization curves were built up in different media and employing Pd and HF as chemical modifiers. Also, a detailed study about calibration strategy was performed. At best conditions, pyrolysis and atomization temperatures were 1200 °C and 2600 °C, respectively, and 10 μL of a 500 mg L^− 1 Pd solution was added together with 10 μL of a 50% (v/v) HF solution on 20 μL of sample. Obtained results indicate that, in this kind of sample, chromium can be determined by standard addition method or employing external calibration with standard solutions prepared in 0.8 mol L^− 1 NaCl medium. In order to evaluate the accuracy of the procedure, a recovery test was performed with seven spiked samples of produced waters. The detection limit, quantification limit and the relative standard deviation in 0.8 mol L^− 1 NaCl were also calculated and the values found were 0.45 μg L^− 1, 1.5 μg L^− 1 and 6.0% (at 2.5 μg L^− 1 level), respectively.     

Determination of zinc and copper in human hair by slurry sampling employing sequential multi-element flame atomic absorption spectrometry

The present work proposes a direct method based on slurry sampling for the determination of zinc and copper in human hair samples by multi-element sequential flame atomic absorption spectrometry. The slurries were prepared by cryogenic grinding and sonication of the samples. The optimization step was performed using univariate methodology and the factors studied were: nature and concentration of the acid solution, amount sample/slurry volume, sonication time, and particle size. The established experimental conditions are the use of a sample mass of 50 mg, 2 mol L^− 1 nitric acid solution, sonication time of 20 min and slurry volume of 10 mL. Adopting the optimized conditions, this method allows the determination of zinc and copper with detection limits of 88.3 and 53.3 ng g^− 1, respectively, and precision expressed as relative standard deviation (RSD) of 1.7% and 1.6% (both, n = 10) for contents of zinc and copper of 100.0 and 33.3 μg g^− 1, respectively. The accuracy was checked and confirmed by analysis of two certified reference materials of human hair. The procedure was applied for the determination of zinc and copper in two human hair samples. The zinc and copper contents varied from 100.0 to 175.6 and from 3.2 to 32.8 μg g^− 1, respectively. These samples were also analyzed after complete digestion in a closed system and determination by FAAS. The statistical comparison by t-test (95% confidence level) showed no significant difference between these results.     

High-accuracy determination of iron in seawater by isotope dilution multiple collector inductively coupled plasma mass spectrometry (ID-MC-ICP-MS) using nitrilotriacetic acid chelating resin for pre-concentration and matrix separation

In the present paper we describe a robust and simple method to measure dissolved iron (DFe) concentrations in seawater down to <0.1 nmol L⁻¹ level, by isotope dilution multiple collector inductively coupled plasma mass spectrometry (ID-MC-ICP-MS) using a ⁵⁴Fe spike and measuring the ⁵⁷Fe/⁵⁴Fe ratio. The method provides for a pre-concentration step (100:1) by micro-columns filled with the resin NTA Superflow of 50 mL seawater samples acidified to pH 1.9. NTA Superflow is demonstrated to quantitatively extract Fe from acidified seawater samples at this pH. Blanks are kept low (grand mean 0.045 ± 0.020 nmol L⁻¹, n = 21, 3× S.D. limit of detection per session 0.020–0.069 nmol L⁻¹ range), as no buffer is required to adjust the sample pH for optimal extraction, and no other reagents are needed than ultrapure nitric acid, 12 mM H₂O₂, and acidified (pH 1.9) ultra-high purity (UHP) water. We measured SAFe (sampling and analysis of Fe) reference seawater samples Surface-1 (0.097 ± 0.043 nmol L⁻¹) and Deep-2 (0.91 ± 0.17 nmol L⁻¹) and obtained results that were in excellent agreement with their DFe consensus values: 0.118 ± 0.028 nmol L⁻¹ (n = 7) for Surface-1 and 0.932 ± 0.059 nmol L⁻¹ (n = 9) for Deep-2. We also present a vertical DFe profile from the western Weddell Sea collected during the Ice Station Polarstern (ISPOL) ice drift experiment (ANT XXII-2, RV Polarstern) in November 2004–January 2005. The profile shows near-surface DFe concentrations of 0.6 nmol L⁻¹ and bottom water enrichment up to 23 nmol L⁻¹ DFe.     

Semi-empirically derived petrophysical and thermodynamical coefficients of permselective shales—Implications on ore mineralization

Phenomenological coefficients of shale–electrolyte systems may offer a glimpse into probable matrix-permeability and solute-exclusionary relationships. Shales from unexposed Upper Cretaceous Period Mancos Shale and from Permian Period Abo Formation were cut into thin wafers, placed in custom built osmometers and a chemical potential applied across them giving rise to induced osmotic flow. This in turn spawned matrix unique constants namely mechanical filtration coefficient L_P (m³ N⁻¹ s⁻¹), diffusional mobility per unit osmotic pressure L_PD (m³ N⁻¹ s⁻¹), osmotic flow coefficient; L_D (m³ N⁻¹ s⁻¹), reflection coefficient σ (dimensionless) at zero gradients of temperature and hydrostatic pressure. Considering intrinsic relationships between these constants where and L_PD = −σL_P, we have ascertained that the bentonitic fossiliferous Mancos shale had a lower L_P and a higher σ compared to the kaolinitic and siliceous shale from Abo Formation indicating a higher degree of compaction post-diagenesis (lower porosity) and higher filtration efficiency. Mechanistic processes involved in solute transport and matrix morphology indicate key multi-scale transformations, ionic- and atomic-exchange competitions on high energy sites like cation-exchange sites, isomorphic substitution at argillaceous mineral edges, atomic-clipping within basal spacing, preferential pathway migration, dead-end pores that give rise to localized solute exclusionary processes and solute attenuation giving rise to anomalous osmotic gradients.     

Oxidation of ascorbic acid in the presence of phthalocyanine metal complexes. Chemical aspects of catalytic therapy of cancer 2. Catalysis by cobalt octacarboxyphthalocyanine. Reaction products

The products of ascorbic acid oxidation in the presence of cobalt octa-4,5-carboxy-phthalocyanine sodium salt (TPH) were identified. These include the ascorbate radical (A^·), hydroxyl radical (OH^·), and hydrogen peroxide (H₂O₂). The kinetics of accumulation and consumption of the reaction products was studied. For the concentration ranges of ascorbic acid = 0–2.5 ⋅ 10⁻³ mol L⁻¹ and the catalyst C _TPH = 0–3.5 ⋅ 10⁻⁵ mol L⁻¹, the the highest possible concentration of the ascorbate radical is ∼10⁻⁷ mol L⁻¹, the concentration of H₂O₂ is 7 ⋅ 10⁻⁴ (30% of the starting concentration of ascorbic acid) and the concentration of the hydroxyl radical is at most 10⁻⁶ mol L⁻¹.__________Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 10, pp. 2224–2228, October, 2004.     

L-Cysteine-coated CdSe/CdS core-shell quantum dots as selective fluorescence probe for copper(II) determination

Quantum dots (QDs) or semiconductor nanocrystals have been receiving great interest in the last few years. In this paper, L-cysteine-coated CdSe/CdS core-shell QDs (λ_em = 585 nm) have been prepared, which have excellent water-solubility. The full width at half maximum (FWHM) of the photoluminescence of these nanocrystals is very narrow (about 30 nm), and the quantum yield (QY) is 15% relative to Rhodamine 6G in ethanol (QY = 95%). With excess free L-cysteine in the solution, the fluorescence intensity of L-cysteine-coated CdSe/CdS QDs showed improved stability. It was found that the fluorescence of L-cysteine-capped CdSe/CdS QDs could be quenched only by copper (II) ions and was insensitive to other physiologically important cations, such as Ca²⁺, Mg²⁺, Zn²⁺, Al³⁺, Fe³⁺, Mn²⁺ and Ni²⁺ etc. Based on this finding, the quantitative analysis of Cu²⁺ with L-cysteine-capped CdSe/CdS QDs has been established. The linear range was from 1.0 × 10^− 8 to 2.0 × 10^− 7 mol L^− 1 and the limit of detection (LOD) was 3.0 × 10^− 9 mol L^− 1 (S/N = 3). The proposed method has first been applied to the determination of Cu²⁺ in vegetable samples with recoveries of 99.6–105.8%.     

Infrared diode laser spectroscopy of the ν = 2 band of AlF

A vibrational–rotational spectrum of the ν = 2 transitions of a high-temperature molecule AlF was observed between 1490 and 1586 cm⁻¹ with a diode laser spectrometer. Measurements were made on the ν = 3–1, 4–2, 5–3 and 8–6 bands at a temperature of 900 °C. Measured spectral lines were fitted to effective band constants ν₀, B_ν and D_ν for each band. Present measurements were made with only one Pb-salt laser diode. Physical significance of the effective band constants is discussed.     

An unprecedented Cu–Schiff base complex existing as two different trinuclear units with strong antiferromagnetic couplings

A new tetradentate N₂O₂ donor Schiff base ligand [OHC₆H₄CHNCH₂CH₂CH(CH₂CH₃)NCHC₆H₄OH = H₂L ] was obtained by 1:2 condensation of 1,3-diaminopentane with salicylaldehyde and has been used to synthesise an unusual copper(II) complex whose asymmetric unit presents two structurally different almost linear trinuclear units [Cu₃(μ-L)₂(ClO₄)₂] [Cu₃(μ-L)₂(H₂O)(ClO₄)₂] (1). The ligand and the complex were characterised by elemental analysis, FT-IR, ¹H NMR and UV–Vis spectroscopy in addition electrochemical and single crystal X-ray diffraction studies were performed for the complex. The magnetic properties of 1 reveal the presence of strong intra-trimer (J₁ = −202(3) cm⁻¹ and J₂ = −233(3) cm⁻¹) as well as very weak inter-trimer (zJ′ = −0.11(1) cm⁻¹) antiferromagnetic interactions.     

Assay of femtogram level nitrite in human urine using luminol–myoglobin chemiluminescence

In this paper, a sensitive flow injection chemiluminescence system luminol–myoglobin was described for determining femtogram nitrite. Nitrite bound myoglobin producing the ferric heme nitrite complexes, which catalyzed the electron transfer of luminol to myoglobin leading to fast chemiluminescence. The chemiluminescence intensity in the presence of nitrite was remarkably enhanced compared with that in the absence of it. Under the optimum reaction conditions the chemiluminescence increment produced was proportional to the concentration of nitrite in the range of 0.05 pg ml^− 1–1.0 ng ml^− 1 (R² = 0.9991), with a detection limit (3σ) of 20.0 fg ml^− 1. At the flow rate of 2.0 ml min^− 1, the whole process including sampling and washing could be completed in 0.5 min offering the sampling efficiency of 120 h^− 1 accordingly, and the relative standard deviation (RSD) was less than 2.60% (n = 5). It was satisfactory for the application to determine nitrite in human urine samples, and the possible mechanism was proposed.     

Enhanced sensitivity for Cu(II) by a salicylidine-functionalized polysiloxane carbon paste electrode

A new approach for decreasing the detection limit for a copper(II) ion-selective electrode (ISE) is presented. The ISE is designed using salicylidine-functionalized polysiloxane in carbon paste. This work describes the attempts to develop the electrode and measurements of its characteristics. The new type of renewable three-dimensional chemically modified electrode could be used in a pH range of 2.3–5.4, and its detection limit is 2.7 × 10⁻⁸ mol L⁻¹ (1.2 μg L⁻¹). This sensor exhibits a good Nernstian slope of 29.4 ± 0.5 mV/decade in a wide linear concentration range of 2.3 × 10⁻⁷ to 1.0 × 10⁻³ mol L⁻¹ of Cu(II). It has a short response time (8 s) and noticeably high selectivity over other Cu(II) selective electrodes. Finally, it was satisfactorily used as an indicator electrode in complexometric titration with EDTA and determination of copper(II) in miscellaneous samples such as urine and various water samples.     

Use of high resolution continuum source atomic absorption spectrometry as a detector for chemically generated noble and transition metal vapors

Vapor generation and atomization conditions in a heated quartz tube to detect Ag, Cd, Co, Cu, Ni and Zn using High Resolution Continuum Source AAS (HRCSAAS), were optimized. Vapors were generated after mixing acidified solutions containing 8-hydroxiquinoline (oxine) with sodium tetrahydroborate. Afterwards, they were swept to the heated quartz cell by an argon flow.Reaction loop size and temperature of the quartz cell were optimized for each element. A temperature of 960 °C was selected as a compromise value to detect most of the metals. Afterwards, a Plackett–Burmann design was proposed to select which parameters were most important. Type of acid and its concentration were the most statistical significant variables. Optimum conditions for sequential detection of Cd, Cu, Ni and Zn were: 1 mg L^− 1 Co as catalyst, 250 mg L^− 1 oxine, 0.6 M nitric acid, 1.75% (w/w) sodium tetrahydroborate (prepared in 0.4 (w/v)% NaOH), a reaction loop of 250 µL, and a 25 L h^− 1 carrier Ar flow. Ag and Co were each detected in their own optimized conditions. Analytical performance of the system was evaluated in connection with a selected pixel number, and spectral correction was used to eliminate NO absorption bands interference in Zn detection. Detection limits were in the range of 1.5–18 μg L^− 1 for Ag, Cu, Cd and Zn, whereas sensitivity was worst for Co (169 μg L^− 1) and Ni (586 μg L^− 1). Atomization in a quartz cell of Co and Ni volatile species, generated by an addition of sodium tetrahydroborate to an acidified solution of the analytes, was reported for the first time in this paper. Precision expressed as RSD(%) had values lower than 10% except for Ni.     

Electroanalytical method for determination of the pesticide dichlorvos using gold-disk microelectrodes

This paper reports the use of laboratory-prepared gold microelectrodes and square-wave voltammetry for analytical determination of low concentrations of the pesticide dichlorvos in pure and natural water samples. After optimization of the experimental and voltammetric conditions, the best voltammetric responses—current intensity and voltammetric profile—were obtained in 0.1 mol L^–1 NaClO₄ with f=100 s^–1, a=50 mV, and E_s=2 mV. The observed detection and quantification limits in pure water were 7.8 and 26.0 g L^–1, respectively. The reproducibility and repeatability of the method were also determined; the results were 1.4% (n=5) and 1.2% (n=10), respectively. Possible interfering effects were evaluated in natural water samples collected at different points with different levels of contamination from agricultural, domestic, or industrial waste from an urban stream. Results showed that the detection and quantification limits increased as a function of the quantity of organic matter present in the samples. Nonetheless, the values observed for these method characteristics were below the maximum value allowed by the Brazilian code for organophosphorus pesticides in water samples. Recovery curves constructed using the standard addition method were shown to be satisfactory compared with those obtained from high-performance liquid chromatography, confirming the suitability of the method for analysis of natural water samples. Finally, when the method was used to determine dichlorvos in spiked cows milk samples, satisfactory recovery and relative standard deviations were obtained.     

The electronic gas-phase spectrum of B3 radical revisited

The gas-phase electronic spectrum of cyclic-B₃ (D_3h) radical has been remeasured in a supersonic molecular beam using a mass-selective resonant 2-color 2-photon technique, leading to a revision of previously reported spectroscopic constants. The species was prepared by ablation of a boron nitride rod in the presence of helium. Ab intio calculations on the geometries and vertical electronic excitation energies, as well as mass identification, indicate that the detected band, centered at 21848.77(2) cm⁻¹, is the origin of the cyclic-¹¹B₃ system. A spectral fit yields the rotational constants as B″ = 1.2246(45) and C″ = 0.62131(72) cm⁻¹ in the ground state, and B′ = 1.1914(44) and C′ = 0.61173(69) cm⁻¹ in the excited 2 ²E′ state.     

Voltammetric determination of quercetin at a multi-walled carbon nanotubes paste electrode

Quercetin can effectively accumulate at multi-walled carbon nanotubes-paraffin oil paste electrodes (CNTPE) and cause a sensitive anodic peak at around 0.32 V (vs. SCE) in a 0.10 M phosphate buffer solution (pH = 4.0). Under optimized conditions, the anodic peak current is linear to quercetin concentration in the ranges of 2.0 × 10^− 9−1.0 × 10^− 7 M and 1.0 × 10^− 7−2.0 × 10^− 5 M, and the regression equations are i_p (μA) = 0.0017 + 0.928c (μM, r = 0.999) and i_p (μA) = 0.183 + 0.0731c (μM, r = 0.995), respectively. This paste electrode can be regenerated by repetitively cycling in a blank solution for about 2 min. A 1.0 × 10^− 6 M quercetin solution is measured for 10 times using the same electrode regenerated after every determination, and the relative standard deviation of the peak current is 1.7%. The method has been applied to the determination of quercetin in hydrolysate product of rutin and the recovery is 99.2–102.6%. In comparison with graphite paste electrode, carbon nanotubes-nujol paste electrode and carbon nanotubes casting film modified glassy carbon electrode, the CNTPE gives higher ratio of signal to background current and better defined voltammetric peak.     

Field-amplified sample injection and in-capillary derivatization for capillary electrophoretic analysis of metal ions in local wines

In-capillary derivatization and field-amplified sample injection (FASI) coupled to capillary zone electrophoresis (CZE) was evaluated for the analysis of metals (Co(II), Cu(II), Ni(II), and Fe(II)) using 2-(5-Nitro-2-Pyridylazo)-5-(N-Propyl-N-Sulfopropylamino)Phenol (Nitro-PAPS) as the derivatizing agent. For FASI, the optimum conditions were water as sample solvent, 1 s hydrodynamic injection (0.1 psi) of a water plug, 5 s of electrokinetic introduction (10 kV) of the sample. The in-capillary derivatization was successfully achieved with zone-passing strategy in order tandem injection of Nitro-PAPS reagent (0.5 psi, 7 s), a small water plug (0.1 psi, 1 s), and metal ion introduction (10 kV, 5 s). The solution of 45 mmol L^− 1 borate pH 9.7 and 1.0 × 10^− 5 mol L^− 1 Nitro-PAPS containing 20% acetonitrile was used as the running buffer. The limit of detection obtained by the proposed method was lower than those from pre-capillary derivatization about 3–28 times. The recovery of the method was comparable to pre-capillary derivatization method. In-capillary derivatization-FASI-CZE was applied to analysis of metals in wine samples. The results were compared with those obtained by CZE with pre-capillary derivatization method and atomic absorption spectrometry (AAS).