Effect of Al2O3 nanoparticles on the steel-glass/epoxy composite joint bonded by a two-component structural acrylic adhesive

This paper reports a study on the effect of Al₂O₃ nanoparticles on the adhesion strength of steel-glass/epoxy composite joints bonded by a two-component structural acrylic adhesive. The addition of Al₂O₃ nanoparticles to the two-component acrylic adhesive led to a remarkable enhancement in the shear and tensile strength of the composite joints. The shear and tensile strength of the adhesive joints increased by addition of Al₂O₃ up to 1.5 wt%, which decreased by further addition of the nanofiller. Introduction of the nanoparticles caused a reduction in the peel strength of the joints. DSC analysis revealed that the glass transition temperature (Tg) of the adhesives rose by increasing the nanofiller content. The advancing water contact angle was decreased for adhesives containing nanoparticles. SEM micrographs indicated good dispersions of the Al₂O₃ nanoparticles within the acrylic matrix in the specimens with up to 1.5 wt% Al₂O₃ and revealed that addition of nanoparticles altered the fracture morphology from smooth to rough fracture surfaces.     

Synthesis of Silica@α-Fe2O3 nanospheres by surface-initiated ATRP

We reported a new method to prepare Silica@α-Fe₂O₃ nanospheres by surface-initiated atom transfer radical polymerization (ATRP). Firstly, polymerizable surfactants-modified α-Fe₂O₃ nanoparticles were prepared in water-toluene microemulsion. Then, as-synthesized α-Fe₂O₃ nanoparticles acted as the macro-monomer of surface-initiated ATRP on silica nanospheres to make target product. Morphological characterization of the product was performed using transmission electron microscopy (TEM). Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS) and diffuse reflectance UV-vis spectroscopy were used to verify the incorporation of α-Fe₂O₃ nanoparticles on silica nanosphere.     

High photocatalytic activity and stability for decomposition of gaseous acetaldehyde on TiO2/Al2O3 composite films coated on foam nickel substrates by sol-gel processes

A set of anatase titanium dioxide (TiO₂) films coated on foam nickel that modified by Al₂O₃ films as transition layer (indicated as TiO₂/Al₂O₃ films) were synthesized via sol-gel route. The bulk and surface properties of the TiO₂/Al₂O₃ films were characterized by thermal gravimetric and differential scanning calorimetry (TG-DSC), X-ray diffraction (XRD), field-emission scanning electron microscope (FE-SEM), and BET. The photocatalytic activities of TiO₂/Al₂O₃ films were investigated based on the degradation of gaseous acetaldehyde under ultraviolet (UV) irradiation. The foam nickel is a promising substrate material in practical applications because of its excellent hydrodynamic properties for gas passing. The TiO₂/Al₂O₃ composite films showed much higher photocatalytic activity and stability for degradation of gaseous acetaldehyde than the onefold TiO₂ films. The significant enhancement in photocatalytic activity and stability can be ascribed to the coating of Al₂O₃ transition layer, which concentrates the target substances around TiO₂ particles and increases the specific surface area (SSA) of the substrate (the SSAs of bare foam nickel and Al₂O₃ modified foam nickel are 0.12 and 113.7 m²/g, respectively) to provide more sites for TiO₂ loading.     

Crystal-chemistry of mullite-type aluminoborates Al18B4O33 and Al5BO9: A stoichiometry puzzle

Orthorhombic Al₂O₃-rich aluminoborate is an important ceramic material for which two slightly different compositions have been assumed: Al₅BO₉ (5Al₂O₃:B₂O₃) and Al₁₈B₄O₃₃ (9Al₂O₃:2B₂O₃). The formula Al₁₈B₄O₃₃ (=Al_4.91B_1.09O₉) was derived from results of chemical analyses when crystal structure data were not yet available. Subsequent structural investigations indicated Al₅BO₉ composition. Nevertheless, Al₁₈B₄O₃₃ was still accepted as the correct stoichiometry assuming that additional B replaces 9% Al.Powder samples of both compositions and ones with excess boron were prepared by solid state reactions between α-Al₂O₃ and B₂O₃/H₃BO₃ at temperatures above 1100 °C and single-crystals were grown from flux at 1100 and 1550 °C. Products were investigated by single-crystal and powder XRD, ¹¹B and ²⁷Al solid-state MAS-NMR, Raman and FTIR spectroscopy as well as Laser-ablation ICP-MS. No indication of the predicted 9% B→Al substitution was found. LA ICP-MS indicated 12.36(27) wt% B₂O₃ corresponding to Al_4.97B_1.03O₉. Hence, the suggested Al₁₈B₄O₃₃ stoichiometry can be excluded for all synthesized samples. A very low amount of Al vacancies at a five-fold coordinated site are likely, charge balanced by an additional nearby three-fold coordinated B site. All evidences indicate that the title compound should be reported as Al_5−xB_1+xO₉ with x<0.038(6), which is close to Al₅BO₉.     

Fabrication, characterization and magnetic behaviour of alumina-doped zinc ferrite nano-particles

Zinc ferrite nano-powders with a nominal composition of ZnFe₂O₄ were prepared by combustion synthesis using mixture of urea and ammonium nitrate as fuel. The influence of alumina-doping on the structural, morphological and magnetic properties of ZnFe₂O₄ nano-particles was investigated by means of X-ray powder diffraction (XRD), infrared (IR) spectroscopy, scanning and transmission electron microscopy (SEM and TEM) and vibrating sample magnetometer (VSM). XRD and IR analyses confirm the cubic spinel phase of ZnFe₂O₄ nano-particles. The Zn ferrite presented a uniform microstructure with grain size in nano-scale. Alumina-doping brought about a change in the morphology of the as prepared ferrite from sphere-like to regular hexagon. Al₂O₃-treatment led to a decrease in the coercivity (H_c), magnetization (M_s) and magnetic moment (n_B) of the investigated system. The maximum decrease in the values of H_c, M_s and n_B due to the treatment with 1.5 wt% Al₂O₃ attained 13.5, 17.4 and 13.5%, respectively. The observed results can be explained on the basis of particle size and the Fe³⁺ concentration in the octahedral and tetrahedral sites involved in the cubic spinel structure.     

Physicochemical and Reactivity Studies on Polystyrene‐Cu/Al2O3 Catalysts: An Attempt to Control Copper Dispersion

The influence of coating of 5.0 (w/w%) Cu/γ‐Al₂O₃ catalyst by different ratios of polystyrene on the physicochemical and textural properties was studied. The physicochemical and textural properties of polystyrene‐`Cu/γ‐Al₂O₃ catalysts were investigated by N₂ adsorption, O₂ chemisorption, FTIR, XRD, TEM, and SEM. In addition, the kinetics of H₂O₂ decomposition as a model redox reaction over polymer coated and uncoated catalysts was investigated. The highest activity was achieved by 0.06 wt% polystyrene‐5.0Cu/γ‐Al₂O₃ catalyst. The parent 5.0Cu/γ‐Al₂O₃ catalyst showed auto‐catalytic first order mechanism, which was subjected to a pronounced modification to a simple first order one upon coating by polystyrene. This modification in the mechanism was accompanied with an increase in the apparent activation energy of the reaction. The observed high activity of 0.06 wt% polystyrene‐5.0Cu/γ‐Al₂O₃ catalyst was attributed to the role of polymer in enhancement of the degree of dispersion of the surface copper. However, the modification in kinetics of the reaction was attributed to the difference in the nature of Cu active sites namely, the polymer protected the metallic copper species on the surface of γ‐Al₂O₃ support against possible oxidation to copper sub‐oxides and/or that polymer might change the hydrophilic properties of the reaction media.     

General Route to Synthesize Monodisperse Oxide (Hydroxide) Nanoparticles

Mono-dispersed oxide and hydroxide nanoparticles have been synthesized through the solvothermal process in alcohol-water mixtures. The products were characterized by powder x-ray diffraction (XRD) and scanning electron microscopy (SEM). Plate-like nanoparticles are obtained for Bi₂O_2.33, Fe₂O₃, and Cd(OH)₂, and spherical nanoparticles are obtained for SnO₂. The growth mechanism for the mono-dispersed nanoparticles has been preliminarily discussed.     

Nox reduction with CO over supported Pd catalysts under simulated post Euro-IV diesel exhaust conditions

The catalytic reduction of NO_x with CO over Pd/Al₂O₃ and Pd/TiO₂/Al₂O₃ under simulated post Euro-IV diesel exhaust conditions was studied. The catalytic activities obtained by using various Pd and TiO₂ loadings and total amounts of reductant and the influence of H₂ and H₂O was investigated.     

Al NMR studies of Ce-Al mixed oxides: origin of 40 ppm peak

CeO₂-γ-Al₂O₃ mixed oxides have been prepared by using both co-precipitation and impregnation methods followed by calcination at 650°C and investigated by ²⁷Al MAS NMR, powder X-ray diffraction and temperature programmed reduction techniques to understand the nature of chemical interaction existing between CeO₂ and γ-Al₂O₃. The ²⁷Al NMR spectra of CeO₂-containing samples showed an additional peak placed at 40 ppm along with the two peaks at 68 and 6 ppm which originate from the tetrahedrally and octahedrally coordinated Al³⁺ ions present in γ-Al₂O₃. As the concentration of CeO₂ in the mixed oxide increased, the intensity of the 40 ppm peak increased and this was the prominent peak for CeO₂-rich mixed oxide samples. The origin of this 40 ppm peak is discussed and it is inferred that this peak is due to Al³⁺ ions, which are present in CeO₂ lattice, forming a solid solution.     

The formation and physicochemical characterization of Al2O3-doped manganese ferrites

Mn/Fe mixed oxide solids doped with Al₂O₃ (0.32-1.27 wt.%) were prepared by impregnation of manganese nitrate with finely powdered ferric oxide, then treated with different amounts of aluminum nitrate. The obtained samples were calcined in air at 700-1000 °C for 6 h. The specific surface area (S_BET) and the catalytic activity of pure and doped precalcined at 700-1000 °C have been measured by using N₂ adsorption isotherms and CO oxidation by O₂. The structure and the phase changes were characterized by DTA and XRD techniques. The obtained results revealed that Mn₂O₃ interacted readily with Fe₂O₃ to produce well-crystallized manganese ferrite (MnFe₂O₄) at temperatures of 800 °C and above. The degree of propagation of this reaction increased by Al₂O₃-doping and also by increasing the heating temperature. The treatment with 1.27 wt.% Al₂O₃ followed by heating at 1000 °C resulted in complete conversion of Mn/Fe oxides into the corresponding ferrite phase. The catalytic activity and S_BET of pure and doped solids were found to decrease, by increasing both the calcination temperature and the amount of Al₂O₃ added, due to the enhanced formation of MnFe₂O₄ phase which is less reactive than the free oxides (Mn₂O₃ and Fe₂O₃). The activation energy of formation (ΔE) of MnFe₂O₄ was determined for pure and doped solids. The promotion effect of aluminum in formation of MnFe₂O₄ was attributed to an effective increase in the mobility of reacting cations.     

氧化铝载体和氧化钡助剂对钌基氨合成催化剂结构和性能的影响

采用不同来源γ-Al2O3(市售Al2O3-1,合成Al2O3-2)作为钌基氨合成催化剂载体,利用浸渍法制备了一系列添加不同BaO助剂含量的Ba-Ru/Al2O3催化剂.通过X射线衍射(XRD)、N2-低温物理吸附、X射线荧光光谱(XRF)、透射电镜(TEM)、H2程序升温还原(H2-TPR)、NH3程序升温脱附(NH3-TPD)和X射线光电子能谱(XPS)等方法研究了不同来源的Al2O3以及BaO助剂含量对负载型钌基催化剂的物相结构、织构性质、微观形貌、表面性质和催化剂的氨合成活性等方面的影响.结果表明,载体的物理化学性质对制备的钌基氨合成催化剂的结构以及活性有较大影响.BaO助剂对催化剂的影响主要表现在两个方面:添加量不同导致BaO与γ-Al2O3的作用力不同,从而进一步影响催化体系的比表面积和孔结构性质;BaO助剂会对体系的Ru物种还原性质以及催化剂表面酸碱性质进行调节,适量BaO的加入能够极大提高反应活性,而这种最佳量与载体性质密切相关.     

Effect of H2S-uptake on the conversion of cyclohexene on Ru- and Pd-promoted molybdena-alumina catalysts

The effect of H₂S on the activity and selectivity of catalysts (Ru/Al₂O₃, Pd/Al₂O₃ and Ru and Pd promoted molydena-alumina) was different (on differnt catalysts and different conversions of cyclohexene). Ru-containing catalysts showed higher sulfur sensitivities than the Pd-containing ones. The sequence of catalysts by their H₂S uptake related to mass of catalyst was PdMo/Al₂O₃RuMo/Al₂O₃Mo/Al₂O₃>Pd/Al₂O₃Ru/Al₂O₃.     

The Effect of MoO3 Addition to V2O5/Al2O3 Catalysts for the Selective Catalytic Reduction of NO by NH3

The effect of MoO₃ addition to alumina supported vanadia catalysts on the catalytic activity for the selective catlaytic reduction of NO is investigated. Upon the addition of MoO₃, catalytic activity is enhanced and the particle size of V₂O₅ which is shown by the results of XRD and Raman spectroscopy is decreased. The MoO₃-V₂O₅/Al₂O₃ catalyst also exhibits more resistance to SO₂ deactivation than V₂O₅/Al₂O₃ does.     

The synthesis mechanism of Ca3Al2O6 from soft mechanochemically activated precursors studied by time-resolved neutron diffraction up to 1000°C

The reaction pathway for the Ca₃Al₂O₆ formation up to 1300°C, from mechanochemically treated mixtures of amorphous aluminum hydroxide and CaCO₃, was studied in situ by differential thermal analysis, constant heating rate dilatometry and time-resolved neutron powder diffraction. The experiment was carried out, in an open system, on a sample with the nominal Ca₃Al₂O₆ stoichiometry. The results obtained by neutron diffractometry and thermal analysis were in good agreement with the data obtained by scanning electron microscopy and X-ray diffraction on heat-treated and-quenched samples. The synthesis path implied the formation of cryptocrystalline Al₂O₃, crystalline CaO, CaAl₂O₄ and Ca₁₂Al₁₄O₃₃ as transitory phases. Finally the nucleation and growth of the single phase Ca₃Al₂O₆ took place at 1300°C and exhibited porous structure due to CO₂ and H₂O release.     

A novel zirconocene/ultradispersed diamond black powder supported catalytic system for ethylene polymerization

A novel carrier of ultradispersed diamond black powder (UDDBP) was used to support metallocene catalyst. Al₂O₃ was also used as carrier in order to compare with UDDBP. Supported catalysts for ethylene polymerization were synthesized by two different reaction methods. One way was direct immobilization of the metallocene on the support, the other was adsorption of MAO onto the support followed by addition of the metallocene. Four supported catalysts Cp₂ZrCl₂/UDDBP, Cp₂ZrCl₂/Al₂O₃, Cp₂ZrCl₂/MAO/UDDBP and Cp₂ZrCl₂/Al₂O₃/MAO were obtained. The content of the zirconium in the supported catalyst was determined by UV spectroscopy. The activity of the ethylene polymerization catalyzed by supported catalyst was investigated. The influence of Al/Zr molar ratio and polymerization temperature on the activity was discussed. The polymerization rate was also observed.     

Elucidation of sulfur mobility on Cr, Mo and W-based catalysts in hydrodesulfurization using a35S pulse tracer method

In hydrodesulfurization of radioactive³⁵S-labeled dibenzothiophene catalyzed by CrO₃/Al₂O₃, it was found that sulfur on sulfided CrO₃/Al₂O₃ was more labile than those on MoO₃/Al₂O₃ and WO₃/Al₂O₃, while the amount of sulfur was less than that on MoO₃/Al₂O₃. Dedicated to Professor Pál Tétényi on the occasion of his 70th birthday     

A simple and effective strategy to synthesize Al2O3-coated LiNi0.8Co0.2O2 cathode materials for lithium ion battery

A facile method has been developed to synthesize Al₂O₃-coated LiNi_0.8Co_0.2O₂ cathode materials. The sample was characterized by X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM) and energy dispersive analysis of X-rays (EDAX). Electrochemical tests show that the cycling stability of LiNi_0.8Co_0.2O₂ at room temperature is effectively improved by Al₂O₃ coating. The differential scanning calorimetry (DSC) and high temperature (60 °C) cycling tests indicate that Al₂O₃ coating can also improve the thermal stability of LiNi_0.8Co_0.2O₂, which is attributed to that the coating layer can protect the LiNi_0.8Co_0.2O₂ particles from reacting with the electrolyte.     

应用原位漫反射红外-质谱技术研究CuO/Al2O3催化剂表面酸性及其反应性能

应用原位漫反射红外-质谱联用、程序升温和暂态响应技术研究了CuO/Al₂O₃催化剂表面酸性及其反应性能. 实验结果表明, CuO/Al₂O₃催化剂表面呈Lewis酸性, 硫化不仅可增强CuO/Al₂O₃催化剂的Lewis酸性, 而且可产生新的Brønsted酸性位; 吸附于Lewis酸性位的NH₃具有选择性催化还原(SCR)活性. 而在硫化样Cu8(400S)中Lewis和Brønsted酸性位同时存在的情况下, 吸附于Lewis和Brønsted酸性位的氨均具有SCR活性, 且后者较前者弱; CuO/Al₂O₃催化剂上的SCR反应遵循Eley-Rideal机理, 即SCR反应发生于吸附态NH₃与气相NO之间.     

Characterization of Ru/CeO2-Al2O3 catalysts and their Performance in CO2 Methanation

Ru/Al₂O₃ and Ru/CeO₂-Al₂O₃ samples were used as catalysts in CO₂ methanation. The catalysts were characterized by temperature-programmed reduction (TPR) and X-ray diffraction. The promoting effect of ceria on the cataytic activity of the catalysts under study in CO₂ methanation was observed.     

Influence of ZrO2 on Carbon Monoxide Oxidation Over Pd/Al2O3

The influence of ZrO₂ on the properties of Al₂O₃ and performances of Pd/Al₂O₃ catalyst in CO oxidation have been investigated. TPD results show that the activity enhanced is due to the increase of the adsorptive capacity of CO and the activation of C=O bond after the introduction of ZrO₂.