Preparation and characterization of a novel nanocomposite particles via in situ emulsion polymerization of vinyl functionalized silica nanoparticles and vinyl acetate

A new class of poly(vinyl acetate) (PVAc)/silica nanocomposite particles was successfully prepared in aqueous solution through a facile synthetic process. First, vinyl functionalized silica nanoparticles (VFSs) were synthesized using one-step method in aqueous emulsion, and then the vinyl groups located on the surface of VFSs were used to induced in situ polymerization of vinyl acetate. Scanning electron microscopy (SEM) images showed that VFSs and PVAc/silica nanocomposite particles all revealed highly monodispersed and uniform spheres. Especially, PVAc/silica nanocomposite particles obtained from transmission electron microscopy images presented an obvious core–shell structure, and the thickness of PVAc shell grafting on the surface of VFSs core was about 17 nm. In addition, the influence of the hydrolyzed and condensed time of vinyl triethoxysilane on the size and size distribution of VFSs was also investigated. The results of dynamic light scattering and SEM analysis indicated that the size and size distribution of VFSs decreased gradually with the extension of the reaction time from 6 to 48 h. Moreover, the structures and thermal properties of the samples were characterized via FT-IR and heat-flow DSC–TG.     

Gas permeation properties of ethylene vinyl acetate–silica nanocomposite membranes

The effect of silica nanoparticles on the gas separation properties of ethylene vinyl acetate (EVA) copolymer containing 28% vinyl acetate has been investigated. The EVA and hybrid EVA–silica membranes were prepared via thermal phase inversion method. Silica nanoparticles prepared by hydrolysis of tetraethylorthosilicate (TEOS), through the sol–gel mechanism. The prepared membranes were characterized using FT-IR, SEM, DSC and XRD methods. FT-IR and SEM results indicated the nanoscale dispersion of silica particles in polymer matrix. As confirmed by XRD and DSC analyses, increasing the silica content enhances the amorphous regions significantly. Gas permeation of EVA–silica nanocomposite membranes with silica contents of 5, 6 and 10 wt.% was studied for N₂, O₂, CO₂ and CH₄ single gases at pressures of 4, 6 and 8 bar. The obtained results suggest a significant increase in permeability of all gases and an increase in CO₂/N₂ and CO₂/CH₄ gases selectivities upon increasing the silica content. The possible reasons for such behavior were stated and discussed. The pressure dependence of the gas permeabilities of the membranes was also investigated.     

Effect of hexagonal boron nitride on poly(vinyl phosphonic acid) composite polymer electrolytes for fuel cells

In this work, hexagonal boron nitride nanoparticles were used as inorganic fillers, which increase the mechanical and thermal stabilities as well as the proton conductivity of the proton conducting composite membranes prepared by blending of poly(vinyl phosphonic acid) and hexagonal boron nitride. Thermo gravimetric analysis showed that the polymer electrolyte membranes are thermally stable up to 200°C. Scanning electron microscopy analysis indicated the homogeneous distribution of boron nitride nanoparticles in the polymer matrix. The crystallinity of the membranes was characterized by using X-ray Diffraction. X-ray patterns support semi-crystalline nature of the composite materials.     

Effect of sepiolite nanoparticles on the properties of novel poly(sulfone ether imide)

A new poly(sulfone ether imide) was prepared, and related nanocomposites were produced through introduction of sepiolite nanoparticles into the matrix of polymer. Inherent viscosity, thermal and mechanical features of pristine poly(sulfone ether imide), and nanocomposite samples were evaluated and compared. The crystallinity was also investigated. Dispersion and distribution behaviors of nanocomposite samples and cross‐sectional morphology of nanocomposite films were also studied. Also, the optimized amounts of sepiolite nanoparticles in the matrix of polymer were determined by microscopic techniques (scanning electron microscope and transmission electron microscope). By introduction of 3 wt% of sepiolite, superior thermal and mechanical properties were observed. Copyright © 2016 John Wiley & Sons, Ltd.     

The synthesis and characterization of polyorganosiloxane nanoparticles from 3-mercaptopropyltrimethoxysilane for preparation of nanocomposite films via photoinitiated thiol-ene polymerization

This article describes the synthesis of modified silica nanoparticles (SiO₂-MPTMS) via the condensation reaction carried out between silanol moieties of silica nanoparticles and the trialkoxy silyl groups of (3-mercaptopropyl) trimethoxysilane (MPTMS). Then, SiO₂-MPTMS nanoparticles in certain amounts (0.5 wt %, 1 wt %, 2.5 wt % and 5 wt %) were incorporated into thiol-ene resins consisting of bisphenol A glycerolate dimethacrylate and trimethylolpropane tris(3-mercaptopropionate) to prepare nanocomposite films via the photoinitiated thiol-ene polymerization in presence of 2,2-Dimethoxy-2-phenylacetophenone 99% as a photoinitiator. Fourier transform infrared spectroscopy, dynamic light scattering, scanning transmission electron microscopy, thermal gravimetric analyzer, and X-ray photoelectron spectrometer were employed to characterize SiO₂-MPTMS nanoparticles. It was revealed that the nanosilica surface was successfully grafted by MPTMS with the grafting ratio of 22.9%. Properties of the nanocomposite films such as decomposition temperature, thermal glass transition temperature, tensile strength, hardness, and particle distribution were investigated and the results were compared with each other and neat film. The addition of MPTMS-modified silica particles did not improve the thermal stability of the films. In scanning electron microscopy study, it was seen that 2.5 wt % of these nanoparticles used as additives were about 200 nm in size and dispersed homogeneously in the polymer matrix. The increase in tensile strength of nanocomposite films compared to the neat film was measured as 77.3% maximum.     

Preparation and characterization of poly(vinyl alcohol)/organo-modified cloisite Na+ with chiral L-leucine amino acid/TiO2 nanocomposites

Poly(vinyl alcohol)/organo-clay/TiO₂ nanocamposites films were prepared with 10 wt % of organo-nanoclay and various amount of TiO₂ nanoparticles. Cloisite Na⁺ has been modified via cation exchange reaction using ammonium salt of natural L-leucine amino acid as a cationic surfactant. After that poly(vinyl alcohol)/organo-nanoclay/TiO₂ nanocomposites were synthesized by dispersion of TiO₂ on the surfaces of organo-nanoclay in poly(vinyl alcohol) matrix by using ultrasonic energy. Three nanocomposites with different loading of TiO₂ were prepared and characterized by X-ray diffraction, fourier transform infrared spectroscopy, field emission type scanning electron microscope, scanning electron microscopy, transmission electron microscopy, thermogravimetric analysis and ultraviolet-visible transmission spectra. The results showed that the organo-nanoclay and TiO₂ were dispersed homogeneously in poly(vinyl alcohol) matrix and also showed improvement in their thermal properties compared with the pure poly(vinyl alcohol).     

Ethylene/vinyl acetate copolymer/clay nanocomposites

This article highlights the history, synthetic routes, material properties, and scope of ethylene/vinyl acetate copolymer (EVA)/clay nanocomposites. These nanocomposites of EVAs are achieved with either unmodified or organomodified layered silicates with different methods. The structures of the resulting polymer/inorganic nanocomposites have been characterized with X‐ray diffraction, scanning electron microscopy, and transmission electron microscopy. The addition of a small amount of clay, typically less than 8 wt %, to the polymer matrix unusually promotes the material properties, such as the mechanical, thermal, and swelling properties, and increases the flame retardancy of these hybrids. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 471–480, 2006     

Mesoporous silica reinforced by silica nanoparticles to enhance mechanical performance

Silica nanoparticle/mesoporous silica composite films were prepared by direct mixing with mechanical stirring and thermal imidization. The structural morphology was elucidated by scanning electron microscopy and the surface of the film was imaged by atomic force microscopy. The functional groups and desorption process of the films were elucidated by Fourier transform infrared spectroscopy and thermal desorption spectroscopy. The mechanical properties were investigated using a nanoindenter system. The gel matrix and the filler are very compatible because they have similar molecular content. The composite films had a higher mechanical strength than pure porous silica film. Their strength is related to the silica nanoparticle content. The interfacial compatibility, dispersion effect, and interfacial strength also affect the mechanical strength of composite films.     

Nanocomposites of vinyl chloride–acrylonitrile copolymer and silica

Vinyl chloride–acrylonitrile (VC–AN) copolymer was synthesized through emulsion copolymerization. VC–AN copolymer/silica nanocomposites were prepared by solution blending of copolymer and silica in a common solvent, N,N‐dimethylformamide (DMF). The rheology studies show that the shear‐thinning behavior of the VC–AN copolymer solution becomes less distinct as nano particles are introduced. It was also found that the viscosity of the copolymer solution decreases with adding small amount of nano particles. Transmission electron microscopy observations indicate that the UV‐treated silica could disperse well in the copolymer matrix. Differential scanning calorimeter studies suggest that the presence of the silica suppresses crystallization of the AN segments in the copolymers. Because of the interactions between copolymer chains and inorganic particles, the thermal stability and mechanical strength of the VC–AN copolymers are improved considerably. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3127–3134, 2005     

Synthesis and characterization of bisulfonated poly(vinyl alcohol)/graphene oxide composite membranes with improved proton exchange capabilities

Composite membranes based on poly(vinyl alcohol) (PVA) and graphene oxide (GO) were prepared by solution-casting method to be used as proton exchange membranes (PEMs) in fuel cell (FC) applications. Bisulfonation was employed as a strategy to enhance the proton conductivity of these membranes. First, a direct sulfonation of the polymer matrix was accomplished by intra-sulfonation of the polymer matrix with propane sultone, followed by the inter-sulfonation of the polymer chains using sulfosuccinic acid (SSA) as a crosslinking agent. Furthermore, the addition of graphene oxide (GO) as inorganic filler was also evaluated to enhance the proton-conducting of the composite membranes. These membranes were fully characterized by scanning electron microscopy (SEM), Fourier transformed infrared spectroscopy (FTIR), thermogravimetric analysis (TGA) and tensile tests. Besides, the proton conductivity of these membranes in a fully hydrated state was also analyzed by electrochemical impedance spectroscopy (EIS). The effect of the intra- and inter-sulfonation of the polymer matrix on the structural, morphological, thermal and mechanical properties of the membranes were determined. Increasing the density of sulfonic acid groups in the membranes resulted in a trade-off between a better proton conductivity (improving from 0.26 to 1.00 mS/cm) and a decreased thermal and mechanical stability. In contrast, the incorporation of GO nanoparticles into the polymer matrix improved the thermal and mechanical stability of both bisulfonated composite membranes. The proton conductivity appreciably increased by the combination of bisulfonation and introduction of GO nanoparticles into the polymer matrix. The sPVA/30SSA/GO composite membrane exhibited a proton conductivity of 1.95 mS/cm at 25 °C. The combination of the GO nanoparticles with the chemical bisulfonation approach of PVA allows thus assembling promising proton exchange membrane candidates for fuel cell applications.     

Compatibility of binary systems of poly(methyl methacrylate), poly(vinyl chloride) and poly(vinyl acetate)

The influence of the thermal treatment on the stability in time of the dispersion degree of films containing binary polymer mixtures, poly(vinyl chloride)/poly(methyl methacrylate), poly(vinyl chloride)/poly(vinyl acetate) and poly(vinyl acetate)/poly(methyl methacrylate), was studied by thermogravimetry and optical microscopy with phase contrast. The dispersion degree depends particularly on the composition of the polymer mixture and can be improved by thermal treatment at temperatures above the glass temperatures of both homopolymers. It seems that this thermal treatment yields exclusively metastable structures with a general tendency to phase separation in a short time after thermal treatment, the heterogeneity mixtures (as film) being more pronounced.     

Preparation and Properties of Poly（vinyl alcohol）/Chitosan Blend Bio-nanocomposites Reinforced by Cellulose Nanocrystals

The aim of this paper is to report the effect of the addition of cellulose nanocrystals（CNCs） on the mechanical, thermal and barrier properties of poly（vinyl alcohol）/chitosan（PVA/Cs） bio-nanocomposites films prepared through the solvent casting process. The characterizations of PVA/Cs/CNCs films were carried out in terms of X-ray diffraction（XRD）, transmission electron microscopy（TEM）, scanning electron microscopy（SEM）, thermogravimetric analysis（TGA and DTG）, oxygen transmission rate（OTR）, and tensile tests. TEM and SEM results showed that at low loading levels, CNCs were dispersed homogenously in the PVA/Cs matrix. The tensile strength and modulus in films increased from 55.1 MPa to 98.4 MPa and from 395 MPa to 690 MPa respectively, when CNCs content went from 0 wt% to 1.0 wt%. The thermal stability and oxygen barrier properties of PVA/Cs matrix were best enhanced at 1.0 wt% of CNCs loading. The enhanced properties attained by incorporating CNCs can be beneficial in various applications.     

Rheology of Poly(vinyl butyral) Solution Containing Fumed Silica in Correlation with Electrospinning

The rheological properties in question are influenced by many factors, ranging from the characteristics of the given polymer or solvent to the flowing conditions. The primary focus of this study is to analyse the rheological behaviour of poly(vinyl butyral)—Mowital B 60 H—(PVB) solutions dissolved in methanol and a blend of these with fumed silica nanoparticles. The preparation of the nanofibrous web and the quality of nanofibres were correlated with the rheology of the polymer solution. It was discerned that drastically intensifying shear viscosity and the elasticity of the solution exerted a negligible effect on the formation of fibres, a finding which has rarely been discussed in the literature. The morphologies and structures of the PVB/silica nanofibrous membranes were investigated by scanning electron microscopy, thermogravimetric analysis and Fourier transform infrared spectroscopy.     

Multifunctional mesoporous silica nanoparticles in poly(ethylene‐co‐vinyl acetate) for transparent heat retention films

Transparent inorganic‐polymer nanocomposite films are of tremendous current interest inemerging solar coverings including photovoltaic encapsulants and commercial greenhouse plastics, but suffer from significant radiative heat loss. This work provides a new and simple approach for controlling this heat loss by using mesoporous silica/quantum dot nanoparticles in poly(ethylene‐co‐vinyl acetate) (EVA) films. Mesoporous silica shells were grown on CdS‐ZnS quantum dot (QDs) cores using a reverse microemulsion technique, controlling the shell thickness. These mesoporous silica nanoparticles (MSNs) were then melt‐mixed with EVA pellets using a mini twin‐screw extruder and pressed into thin films of concentration variable controlled thickness. The results demonstrate that the experimental MSNs showed improved infrared and thermal wavebands retention in the EVA transparent films compared to commercial silica additives, even at lower concentrations. It was also found MSNs enhanced the quantum yield and photostability of the QDs, providing high visible light transmission and blocking of UV transmission of interest for next generation solar coatings. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 851–859     

Polyethylene-based nanocomposite: Structure and properties of poly(vinyl alcohol)/organofunctionalized Mg-doped fluorapatite hybrid

We report here the production and characterization of polymer nanocomposites (NC)s containing nanoceramics of organofunctionalized Mg-doped fluorapatite (MDFA) in a poly(vinyl alcohol) matrix. First, the MDFA materials were functionalized with N-trimellitylimido-L-leucine modifier through ultrasonic irradiation. The numerous experimental techniques like Fourier transform infrared spectroscopy, X-ray diffraction, atomic force microscopy, field emission scanning electron microscopy, transmission electron microscopy, and thermogravimetric analysis were applied to characterize the prepared materials. Thermal analysis of the obtained NCs showed an increase in thermal stability of the NCs when compared to the neat macromolecule.     

Application of CuO nanoparticles modified with vitamin B1 for the production of poly(vinyl alcohol)/CuO nanocomposite films with enhanced optical,thermal and mechanical properties

In this Investigation, the CuO nanoparticles (NPs) were treated by vitamin B₁ as a biomolecule modifier. The CuO NPs were used as an appropriate filler for fabrication of poly(vinyl alcohol) (PVA) nanocomposites (NCs). Then, NCs with various ratios (3, 5, and 7wt%) of modified CuO were fabricated under ultrasonic irradiation and their properties were compared with pure PVA. Several techniques were used for characterization of NCs. Field emission scanning electron microscopy and transmission electron microscopy analysis indicated that NPs have proper compatibility with the PVA matrix. Thermal gravimetric analysis results confirmed that NCs displayed higher thermal stability than neat PVA. Also, the addition of the NPs into the PVA matrix improved the optical and mechanical behaviors. Finally, the contact angle measurements verified that the hydrophilicity decreased for different ratios of modified NPs loaded in the polymer matrix. Copyright © 2017 John Wiley & Sons, Ltd.     

Mixed surfactants-directed the mesoporous silica materials with various morphologies and structures

A new mixed surfactants system using alkyl carboxylic acids and quaternized poly[bis(2-chloroethyl)ether-alt-1,3-bis[3-(dimethylamino)propyl] urea] (PEPU) as the co-template was used to synthesize mesoporous silica materials with various morphologies and structures, including flakes, regular spheres, nanoparticles, and tube-spheres. The cationic polymer connected the anionic surfactant micelle to the anionic polysilicate species to induce the synthesis of the mesoporous silica materials. The structure and property of the surfactant and the cationic polymer determined the formation of mesoporous silica, and also had a signification influence on the morphology and structure of the final materials. To further explore the possible formation mechanism of these mesoporous materials, zeta potential was utilized to evaluate the interaction between the anionic surfactant and the cationic co-template. In addition, the structure, morphology, and porosity of these materials were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and N₂ adsorption-desorption measurements.     

Relationship between the polymer/silica interaction and properties of silica composite materials

Cast film composites have been prepared from aqueous polymer solutions containing nanometric silica particles. The polymers were polyvinyl alcohol (PVA), hydroxypropylmethylcellulose (HPMC) and a blend of PVA‐HPMC polymers. In the aqueous dispersions, the polymer–silica interactions were studied through adsorption isotherms. These experiments indicated that HPMC has a high affinity for silica surfaces, and can adsorb at high coverage; conversely, low affinity and low coverage were found in the case of PVA. In the films, the organization of silica particles was investigated through transmission electron microscopy (TEM) and small‐angle neutron scattering (SANS). Both methods showed that the silica particles were well‐dispersed in the HPMC films and aggregated in the PVA films. The mechanical properties of the composite films were evaluated using tensile strength measurements. Both polymers were solid materials, with a high‐elastic modulus (65 MPa for HPMC and 291 for PVA) and a low‐maximum elongation at break (0.15 mm for HPMC and 4.12 mm for PVA). In HPMC films, the presence of silica particles led to an increase in the modulus and a decrease in the stress at break. In PVA films, the modulus decreased but the stress at break increased upon adding silica. Accordingly, the polymer/silica interaction can be used to tune the mechanical properties of such composite films. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1134–1146, 2006     

Miscibility behaviour of blends of a thermoplastic polyester polyurethane with vinyl polymers

A method based on the intrinsic viscosities of transfer has been used to predict miscibility of polymer blends. This method has been applied to study the change in the phase behaviour of a microphase separated polyester polyurethane (PSPU) on blending with polyvinyl chloride (PVC), polyvinyl acetate (PVAc) and a vinyl chloride-vinyl acetate copolymer (VCVAc). The PVC/PSPU blends are found to exhibit complete miscibility over the entire composition range. PVAc/PSPU blends show immiscibility while VCVAc/PSPU blends show partial miscibility. Thermal analysis and scanning electron microscopic studies of the blend films have confirmed the results evaluated on the basis of the viscosity method.     

Microstructure and properties of organosoluble polyimide/silica hybrid films

Organosoluble polyimide/silica hybrid materials were prepared via the sol-gel process and their pervaporation properties were studied. The organosoluble polyimide (PI) was based on 4,4′-oxydiphthlic dianhydride (ODPA) and 4,4′-diamino-3,3′-dimethyldiphenylmethane (DMMDA). The surface chemical structure of polyimide/silica films was analyzed by Fourier transform infrared (FT-IR) and X-ray photoelectron spectroscopy (XPS) and the results show that the completely hydrolysis of alkoxy groups of precursors and formation of the three-dimensional Si-O-Si network in the hybrid films. The morphology and the silica domain thus obtained were studied by scanning electron microscopy (SEM) and atomic force microscopy (AFM), respectively. The silica particle size in the hybrid is in the range of 40-100 nm for the hybrid films when the amount of silica is less than 20 wt%. The strength and the modulus of the hybrid films are improved and the mechanical properties were found to be strongly dependent on the density of the crosslink. The glass transition temperature (T_g) of the hybrid films was determined by dynamic mechanical analysis (DMA) and the value increased 15-20 °C as the silica content increased. Furthermore, the pervaporation performances of the prepared hybrid films were also investigated for the ethanol/water mixtures at different temperature.