Preparation and Properties of Aliphatic Polybenzoxazoles from 4,4′-Diamino-3,3′-Dihydroxybiphenyl and Aliphatic Dicarboxylic Acid Chlorides by the Silylation Method

Abstract

A series of aliphatic polybenzoxazoles of high molecular weights was prepared in three steps by the low-temperature solution polycondensation of tetrakis(trimethylsilyl)-substituted 4,4′-diamino-3,3′-dihydroxy-biphenyl with aliphatic diacid chlorides with 7 to 12 methylene units yielding trimethylsilyl-substituted poly(o-hydroxysamide) precursor polymers, which were subjected to desilylation with methanol giving the poly(o-hydroxyamide)s, followed by thermal cyclodehydration. The aliphatic polybenzoxazoles had melting points in the 172 to 246 °C range with glass transition temperatures of 55-97°C. They were stable in the melt state up to 400 °C in nitrogen. These polybenzoxazoles and the corresponding bisbenzoxazole model compounds exhibited no liquid crystallinity.     

Synthesis and properties of new soluble aromatic polybenzoxazoles from 4,4′-diamino-3,3′-dihydroxytriphenylamines and aromatic dicarboxylic acids

Two new triphenylamine-based bis (o-aminophenol) monomers, 4,4′-diamino-3,3′-dihydroxytriphenylamines, were successfully synthesized by the cesium fluoride-mediated condensation of 2-(benzyloxy)-4-fluoronitrobenzene with aniline derivatives, followed by simultaneous deprotection and reduction. Aromatic polybenzoxazoles having inherent viscosities of 0.58–1.05 dL/g were obtained by the low-temperature solution polycondensation of the bis(aminophenol)s with various aromatic dicarboxylic acid chlorides and the subsequent thermal cyclodehydration of the resultant poly(hydroxyamide)s. All the polybenzoxazoles were amorphous, and most of them were soluble in organic solvents such as m-cresol and o-chlorophenol. Flexible and tough films of polybenzoxazoles could be cast from the DMAc solutions of some aromatic poly(hydroxyamide)s, followed by thermal cyclodehydration. The glass transition temperatures and 10% weight loss temperatures of the polybenzoxazoles under nitrogen were in the range of 262–327 and 610–640°C, respectively. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1987–1994, 1998     

Vapor phase deposition of polybenzoxazoles

Vapor phase deposition was carried out on multifunctional aliphatic and aromatic benzoxazoles to yield powdered samples of poly(dimethylenebenzoxazoles). Representative aliphatic and aromatic poly(dimethylenebenzoxazoles) were also synthesized through solution methods using 4-amino-3-hydroxyhydrocinnamic acid and 2-(4-(bromomethyl)phenyl)-6-(bromomethyl)benzoxazole, respectively, as monomers. Both aromatic and aliphatic polybenzoxazoles containing  CH₂CH₂ units in the polymer backbone displayed catastrophic weight loss over a very narrow temperature range. This is in contrast with other polybenzoxazoles which show a gradual weight loss over 500–1000°C. Vapor phase deposition carried out under vacuum on the polymers gave similar polymers in the collection zone suggesting the catastrophic weight loss is attributed to thermal depolymerization of the polymer through a diradical intermediate similar to the thermolysis and polymerization of [2.2]paracyclophane. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1317–1328, 1998     

Aromatic polybenzoxazoles containing ether–sulfone linkages

A series of poly(o‐hydroxy amide)s having both ether and sulfone linkages in the main chain were synthesized via the low‐temperature solution polycondensation of 4,4′‐[sulfonylbis(1,4‐phenylene)dioxy]dibenzoyl chloride and 4,4′‐[sulfonylbis(2,6‐dimethyl‐1,4‐phenylene)dioxy]dibenzoyl chloride with three bis(o‐aminophenol)s including 4,4′‐diamino‐3,3′‐dihydroxybiphenyl, 3,3′‐diamino‐4,4′‐dihydroxybiphenyl, and 2,2‐bis(3‐diamino‐4‐hydroxyphenyl)hexafluoropropane. Subsequent thermal cyclodehydration of the poly(o‐hydroxy amide)s afforded polyethersulfone benzoxazoles. Most of the poly(o‐hydroxy amide)s were soluble in polar organic solvents such as N‐methyl‐2‐pyrrolidone; however, the polybenzoxazoles without the hexafluoroisopropylidene group were organic‐insoluble. The polybenzoxazoles exhibited glass‐transition temperatures (T_g) in the range of 219–282 °C by DSC and softening temperatures (T_s) of 242–320 °C by thermomechanical analysis. Thermogravimetric analyses indicated that most polybenzoxazoles were stable up to 450 °C in air or nitrogen. The 10% weight loss temperatures were recorded in the ranges of 474–593 °C in air and 478–643 °C in nitrogen. The methyl‐substituted polybenzoxazoles had higher T_g's but lower T_s's and initial decomposition temperatures compared with the corresponding unsubstituted polybenzoxazoles. For a comparative purpose, the synthesis and characterization of a series of sulfonyl polybenzoxazoles without the ether group that derived from 4,4′‐sulfonyldibenzoyl chloride and bis(o‐aminophenol)s were also reported. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2262–2270, 2001     

Synthesis of fluorinated polybenzoxazoles with low dielectric constants

Two fluorinated aromatic bis(o‐aminophenol)s, 1,1‐bis(3′‐amino‐4′‐hydroxyphenyl)‐1‐(3′‐trifluoromethylphenyl)‐2,2,2‐trifluoroethane (6FAP) and 1,1‐bis(3′‐amino‐4′‐hydroxyphenyl)‐1‐(3′,5′‐ditrifluoromethylphenyl)‐2,2,2‐trifluoroethane (9FAP) were synthesized, which were allowed to polycondense with aromatic diacyl chlorides to afford the fluorinated aromatic polybenzoxazoles (PBOs) via a conventional two‐step procedure in which the low‐temperature solution polycondensation process was first performed to yield poly(o‐hydroxyamide)s (PHAs) followed by the thermal cyclodehydration to give the PBOs. Experimental results indicated that the PHAs had inherent viscosities in the range of 0.29–0.68 dL/g, showing excellent solubility in organic solvents. The PHAs could be thermally cyclodehydrated into the corresponding PBOs at 260–370 °C. The obtained PBOs exhibited enhanced glass‐transition temperature but decreased solubility with respect to the PHAs. The PBOs showed glass‐transition temperatures in the range of 315–337 °C and excellent thermal stabilities with 5% original weight‐loss temperatures (T₅) of >513 °C. Additionally, the PBO films had average refractive index of 1.5298–1.5656, birefringence of 0.0051–0.0092, and low dielectric constants of 2.57–2.70. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis and properties of novel cardo aromatic poly(ether‐benzoxazole)s

Three new bis(ether‐acyl chloride) monomers, 1,1‐bis[4‐(4‐chloroformylphenoxy)phenyl]cyclohexane ( 1a ), 5,5‐bis[4‐(4‐chloroformylphenoxy)phenyl]‐4,7‐methanohexahydroindan ( 1b ), and 9,9‐bis[4‐(4‐chloroformylphenoxy)phenyl]fluorene ( 1c ), were synthesized from readily available compounds. Aromatic polybenzoxazoles bearing ether and cardo groups were obtained by the low‐temperature solution polycondensation of the bis(ether‐acyl chloride)s with three bis(aminophenol)s and the subsequent thermal cyclodehydration of the resultant poly(o‐hydroxy amide)s. The intermediate poly(o‐hydroxy amide)s exhibited inherent viscosities in the range of 0.35–0.71 dL/g. All of the poly(o‐hydroxy amide)s were amorphous and soluble in many organic polar solvents, and most of them could afford flexible and tough films by solvent casting. The poly(o‐hydroxy amide)s exhibited glass‐transition temperatures (T_g's) in the range of 141–169 °C and could be thermally converted into the corresponding polybenzoxazoles approximately in the region of 240–350 °C, as indicated by the DSC thermograms. Flexible and tough films of polybenzoxazoles could be obtained by thermal cyclodehydration of the poly(o‐hydroxy amide) films. All the polybenzoxazoles were amorphous and showed an enhanced T_g but a dramatically decreased solubility as compared with their poly(o‐hydroxy amide) precursors. They exhibited T_g's of 215–272 °C by DSC and showed insignificant weight loss before 500 °C in nitrogen or air. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 4014–4021, 2001     

Synthesis of hydroxyl-containing polyamides by ring-opening polyaddition of 4,4′-disubstituted bis(4-butanolide) with aliphatic diamines

Hydroxyl-containing polyamides have been prepared by the ring-opening polyaddition of 4,4′-oxydi-p-phenylenebis(4-butanolide) with aliphatic diamines in alcoholic solvents at 65–80°C. These polymers having inherent viscosities ranging from 0.1 to 0.5 were soluble in a variety of solvents including dimethylformamide, formic acid, and m-cresol. Transparent and flexible films cast from these solutions were highly hygroscopic. All the polymers had low softing temperatures in the range of 115–130°C, and began to decompose at around 250°C, both in air and under nitrogen.     

Synthesis and ring‐opening polymerization of co‐cyclic(aromatic aliphatic disulfide) oligomers

An effective approach was presented for the synthesis of co‐cyclic(aromatic aliphatic disulfide) oligomers by catalytic oxidation of aromatic and aliphatic dithiols with oxygen in the presence of a copper‐amine catalyst. The aromatic dithiols can be 4,4′‐oxybis(benzenethiol), 4,4′‐diphenyl dithiol, 4,4′‐diphenylsulfone dithiol. The aliphatic dithiols can be 1,2‐ethanedithiol, 2,3‐butanedithiol, 1,6‐hexane dithiol. The co‐cyclic(aromatic aliphatic disulfide) oligomers were characterized by gradient HPLC, MALDI‐TOF‐MS, GPC, ¹H‐NMR, TGA, and DSC techniques. The glass transition temperatures of these co‐cyclics ranged from ?11.3 to 56.6°C. In general, these co‐cyclic(aromatic aliphatic disulfide) oligomers are soluble in common organic solvents, such as CHCl₃, THF, DMF, DMAc. These co‐cyclic oligomers readily underwent free radical ring‐opening polymerization in the melt at 180°C, producing linear, tough and high molecular weight poly(aromatic aliphatic disulfide)s. The glass transition temperatures of these polymers ranged from ?3.7 to 107.8°C that are higher than those of corresponding co‐cyclics. Copyright © 2003 John Wiley & Sons, Ltd.     

Novel thermooxidatively stable poly(ether-imide-benzoxazole) and poly(ester-imide-benzoxazole)

4-Hydroxy-5-nitrophthalimides were produced via nucleophilic aromatic substitution (NAS) of 4,5-dichloro phthalimide substituents by potassium nitrite. The use of a N-phenyl-phthalimide having a protected 4′-hydroxyl group allows concurrent deprotection and nitro reduction to amine to give the 4-hydroxy-5-amino-N-(4′-hydroxyphenyl) phthalimide. This key intermediate is the precursor to a poly (ether-imide-benzoxazole), and is the condensable monomer for a poly (ester-imide-benzoxazole). Benzoxazole monomer formation via condensation with p-fluorobenzoyl chloride afforded 2-(4′-fluorophenyl)-5,6,-N-[4′(-hydroxyphenyl) imide]-benzoxazole, which was polymerized under NAS conditions to produce a poly(ether-imide-benzoxazole) having an endothermic transition at 454°C with weight retention of 90% at 500°C in both air and nitrogen. Solution polycondensation of the 4-hydroxy-5-amino-N-(4′-hydroxyphenyl) phthalimide monomer with isophthaloyl chloride afforded a poly(ester-amide-imide) which was isolated and thermally cyclodehydrated in the solid state under vacuum to give a poly(ester-imide-benzoxazole) having 95% weight retention at 500°C in both air and nitrogen, with no detectable DSC transitions up to 500°C. © 1994 John Wiley & Sons, Inc.     

Synthesis of aliphatic polyesters by polycondensation using inorganic acid as catalyst

An effective route for the synthesis of aliphatic polyesters made from adipic or sebacic acid and alkanediols, using inorganic acid as a catalyst is reported. The monomer composition, reaction time, catalyst type, and reaction conditions were optimized to yield polyesters with weight average molecular weights of 23,000 for adipic acid and 85,000 for sebacic acid‐based polyesters. The polymers melt at temperatures of 52–65°C and possess melt viscosity in the range of 5600–19,400cP. This route represents an alternative method for producing aliphatic polyesters for possible use in the preparation of degradable disposable medical supplies. Copyright © 2009 John Wiley & Sons, Ltd.     

High-pressure synthesis and properties of aliphatic–aromatic polyimides via nylon-salt-type monomers derived from aliphatic diamines and benzophenonetetracarboxylic acid

Aliphatic polyimides (P-XBTA) having inherent viscosities of 0.4–1.4 dL/g were readily synthesized by the high-pressure polycondensation of the salt monomers, composed of aliphatic diamines having various methylene chain lengths (X = 4–12) and 3,3′,4,4′-benzophenonetetracarboxylic acid (BTA), under 200–250 MPa at 200–320°C. The salt monomers with odd-numbered methylene units were found to be more susceptible to crosslinking than those containing even-numbered methylene chains. The polyimides having even-numbered methylene units were highly crystalline, whereas those with odd-numbered methylene chains were crosslinked and therefore amorphous with only one exception, i.e., P-11BTA. The thermal behavior of these polymers was also studied. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 39–47, 1998     

Synthesis and characterization of fully aliphatic polyimides from an aliphatic dianhydride with piperazine spacer for enhanced solubility,transparency, and low dielectric constant

A new series of fully aliphatic polyimide (API) based on a novel aliphatic dianhydride monomer‐2,2′‐(1,4‐piperazinediyl)‐disuccinic anhydride (PDA), in which two units of succinic anhydride have been connected by an aliphatic heterocyclic piperazine spacer that possesses aminomethylene (‐NCH₂) moiety in the aliphatic/alicylic backbone capable of inducing charge transfer (CT) interactions in the polyimide network, was successfully synthesized. The APIs were soluble in common polar organic solvents. The polyimide films of PDA with alicyclic diamines were almost colorless. T₁₀ (temperature of 10% weight loss) of APIs were ranged from 299–418 °C and T_g of API3‐API6 were in the temperature range of 170 to 237 °C. The light‐colored polyimide films of API3‐API6 possessed good mechanical properties with tensile strength of 54–72 Mpa, tensile modulus of 1.6–2.3 Gpa and elongation at break of 4–9%. The polyimide films of API3‐API6 were highly flexible and free‐standing which is quite rare in fully APIs. The dielectric constant of one of the synthesized API (API4) was as low as 2.14. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2316–2328     

Synthesis and properties of novel aromatic poly(o-hydroxy amide)s and polybenzoxazoles based on the bis(ether benzoyl chloride)s from hydroquinone and its methyl-, tert-butyl-, and phenyl-substituted derivatives

Four series of poly(o-hydroxy amide)s were prepared by the low-temperature solution polycondensation of the bis(ether benzoyl chloride)s extended from hydroquinone and its methyl-, tert-butyl-, or phenyl-substituted derivatives with three bis(o-aminophenol)s. Most of the poly(o-hydroxy amide)s displayed an amorphous nature, were readily soluble in various polar solvents such as N,N-dimethylacetamide (DMAc), and could be solution-cast into flexible and tough films. These poly(o-hydroxy amide)s had glass transition temperatures (T_g) in the range of 152–185°C and could be thermally cyclodehydrated into the corresponding polybenzoxazoles approximately in the region of 200–400°C, as evidenced by the DSC thermograms. The thermally converted benzoxazole polymers exhibited T_gs in the range of 215–247°C and did not show significant weight loss before 500°C either in nitrogen or in air. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2129–2136, 1999     

Enzymatic degradation of aliphatic polyesters copolymerized with various diamines

Poly(hexamethylene adipate) copolymers with 10–40 mol-% (in feed) of aliphatic diamines of various methylene chain lengths were prepared by melt polycondensation. In vitro degradation was performed in buffer solution at 37°C with a lipase and was evaluated by weight loss of the films. The weight loss increased greatly by the copolymerization and showed a maximum at 10 mol-% of comonomer content. Degradation also increased in a zig-zag fashion with decreasing number of methylene chains in the diamine comonomers. Both effects on the enzymatic degradation are discussed.     

Synthesis of polyamides by ring-opening polyaddition of 4,4′-disubstituted bis(3-buten-4-olide) with aliphatic diamines

An investigation of the reaction of 4-phenyl-3-buten-4-olide with benzylamine was conducted as a model for the polymerization, and some ethers and acidic solvents were found to be favorable reaction media for formation of the ring-opened amide as the sole product. By using m-cresol as the polymerization medium, linear polyamides having inherent viscosities up to 0.67 were readily prepared by the ring-opening polyaddition of 4,4′-oxydi-p-phenylenebis(3-buten-4-olide) with aliphatic diamines at room temperature. These polymers were soluble in m-cresol and gave transparent, flexible films by the solution casting technique. They did not show any melt temperature, and began to decompose at around 200°C, both in air and under nitrogen.     

Preparation and properties of aromatic–aliphatic copolyamides from aromatic diisocyanates and dicarboxylic acids

Aromatic–aliphatic random copolyamides of high molecular weights were prepared by the high-temperature solution polycondensation from a combination of aromatic diisocyanates, 4,4′-methylenedi(phenyl isocyanate), and 2,4-tolylene diisocyanate, and a mixture of isophthalic acid and aliphatic dicarboxylic acids with 4–10 methylene groups. Reaction conditions, such as solvent, temperature, time, and catalyst were studied to determine the optimum conditions for the preparation of high molecular weight polymers. Glass transition temperatures of the copolyamides were in the range of 131–244°C and varied with combination and composition of the diisocyanates and dicarboxylic acids used. The copolyamides prepared from 2,4-tolylene diisocyanate had greater solubility and higher glass transition temperatures than those obtained from 4,4′-methylenedi(phenyl isocyanate).     

Regular copolyamides. II. Preparation and characterization of regular aliphatic copolyoxamides

Regular copolyoxamides were prepared from diamine-oxamides and aliphatic diacid chlorides by interfacial and solution polymerization. Interfacial polymerization is preferred with diamineoxamides where the diamine portion has two to six methylene groups and the diamine-oxamides are readily soluble in water. Regular aliphatic polyoxamides from diamine-oxamides are readily soluble in water. Regular aliphatic polyoxamides from diamine-oxamides with more than six methylene groups in the diamine portion of the molecule are better prepared by solution polymerization in dimethyl acetamide. Regular aliphatic oxamides are soluble in trifluoroacetic acid and hexafluoroisopropanol and show a considerable alternation of the melting point behavior in the diamine portion of the polyamides with up to five methylene groups. Copolyoxamides with two and four methylene groups melt higher than the copolyoxamides with three and five methylene groups. Aliphatic copolyoxamides/adipamides melt at approximately 260°C and show a steady decrease in melting points to about 220°C for polyoxamides with twelve methylene groups.     

Synthesis of polybenzodipyrrolediones by thermal cyclodehydration of polyamides derived from dibenzylidenebenzodifurandiones and aliphatic diamines

A new class of polyheterocycles, polybenzodipyrrolediones (PBP), has been synthesized successfully by the two-step polymerization of dibenzylidenebenzodifurandiones with aliphatic diamines. New bislactone monomers, 3,5-dibenzylidene-3,5-dihydro-1H,7H-benzo[1,2-c:4,5-c′]difuran-1,7-dione and 3,7-dibenzylidene-3,7-dihydro-1H,5H-benzo[1,2-c:4,5-c′]-difuran-1,5-dione, were synthesized from pyromellitic dianhydride and phenylacetic acid. The ring-opening polyaddition reaction of the bislactones with aliphatic diamines in a polar solvent afforded novel polyamides having inherent viscosities of 0.1–1.0 in quantitative yield. The solution polymerization was almost completed within several hours at 80°C, while it required approximately a week to its completion at room temperature. Dimethyl sulfoxide and N-methyl-2-pyrrolidone were preferred solvents for the polymerization. The open-chain polyamides were subsequently cyclodehydrated by heating at 240°C to give PBP having high molecular weight. The aliphatic PBP were soluble in hot polar solvents such as N-methyl-2-pyrrolidone, m-cresol, and nitrobenzene. They began to decompose at about 400°C in a nitrogen atmosphere as determined by thermogravimetric analysis.     

Synthesis of benzylidene-pendant polyphthalimidines from flexible bisphthalides and various diamines

New polyphthalimidine-forming monomers, 5,5′-(oxydi-p-phenylenedicarbonyl)bis(3-benzylidenephthalide) and the 6,6′-derivative, were synthesized by the Friedel–Crafts reaction of diphenyl ether with 5- and 6-chloroformyl-3-benzylidenephthalide, respectively. The direct polycondensation of these bisphthalides with both aliphatic and aromatic diamines in o-phenylphenol at 200–250°C afforded polyphthalimidines having inherent viscosities of 0.2–1.2 dL/g in almost quantitative yields. Syntheses of aliphatic polyphthalimidines with higher inherent viscosities were also achieved by a two-step procedure involving ring-opening polyaddition and subsequent thermal cyclodehydration. All the polymers were amorphous and readily soluble in N-methyl-2-pyrrolidone (NMP), m-cresol, nitrobenzene, pyridine, and chloroform. Tough and flexible films could be cast from NMP solutions of the polymers. Glass transition temperatures of the polyphthalimidines were in the range of 158–246°C. The thermogravimetry of the aromatic polymers showed 10% weight loss in air and nitrogen at 445–515 and 500–520°C, respectively. The crosslinking reaction of some benzylidenependant polyphthalimidines took place at 300°C through double-bond addition to afford cured polymers with improved thermal stability.     

Polymerization of N-(p-aminobenzoyl)caprolactam: Block and alternating copolymers of aromatic and aliphatic polyamides

The polymerization behavior of N-(p-aminobenzoyl)caprolactam was studied. It was found that polymerization could proceed by either elimination of caprolactam or by ring opening. Polymers prepared at temperatures above 200°C showed a greater tendency for ring opening to produce alternating aromatic/aliphatic copolymers than did polymers prepared at lower temperatures. Block copolymers of poly(p-benzamide) and nylon 6 were prepared by a two-stage hydrolytic polymerization process or by anionic polymerization at temperatures > 200°C. Polymer microstructures were determined using ¹³C-NMR spectroscopy by comparison with homopolymers and model alternating copolymers. The alternating copolymer prepared by condensation of N-(p-aminobenzoyl)-6-caproic acid showed a melting transition at 300–305°C in the DSC and a T_g in subsequent heating cycles of 116–119°C. Copolymers made with the two-stage process were rich in p-benzamide sequences and showed no T_g or T_m below 400°C. Copolymer made with NaH was rich in nylon 6 units, showed a T_m of 175–180°C and a T_g of 80–81°C, and was homogeneous in both the melt and solid.