Ultrasound extraction and thin layer chromatography-flame ionization detection analysis of the lipid fraction in marine mucilage samples

This paper reports an analytical procedure based on ultrasound to extract lipids in marine mucilage samples. The experimental conditions of the ultrasound procedure (solvent and time) were identified by a FT-IR study performed on different standard samples of lipids and of a standard humic sample, before and after the sonication treatment. This study showed that diethyl ether was a more suitable solvent than methanol for the ultrasonic extraction of lipids from environmental samples because it allowed to minimize the possible oxidative modifications of lipids due to the acoustic cavitation phenomena. The optimized conditions were applied to the extraction of total lipid amount in marine mucilage samples and TLC-flame ionization detection analysis was used to identify the relevant lipid sub-fractions present in samples.     

Speciation of organomercurials in marine samples using capillary electrophoresis

A rapid method for speciation and determination of organomercury compounds in biological samples of marine origin using Capillary Electrophoresis (CE) is reported. Organomercurials were extracted from the samples by means of the classical West?? procedure thus giving organomercury-cysteine complexes which can be separated from each other by means of CE resulting in effective speciation. Electrophoretic separation was achieved in an open silica capillary tube at 15-18 kV using a 100mM sodium borate buffer (pH 8.35). All mercury species were distinctively separated within 12 min. Results are presented for the analysis of real marine samples and reference materials, and compared with those obtained by the GC commonly accepted procedure.     

Rapid estimation of TOC in a marine urban sewage area by UV spectral deconvolution

A simple and rapid procedure for on-site qualitative and quantitative analysis of organic matter from discharges of municipal wastewater in seawater has been developed. This method is based on the knowledge of the UV signal of both seawater and anthropogenic absorbing matter and on the mathematical deconvolution of the sample spectrum using reference spectra. The main application is the estimation of TOC at the direct outlet of the discharge. This quantitative application is obviously limited by the nature of organic compounds, but the UV estimation allowed us to have an overview of the composition and evolution of organic matter into the polluted area. The application of this procedure has been carried out to study the wastewater dilution into an area receiving urban discharges. Experiments showed satisfactory analytical features with a range of TOC values from 75 to 1500?µM C, and the comparison of the results with those obtained by reference method presented a reasonable correlation (r ²?=?0.9636) in the marine discharge. The results have also allowed us to quickly estimate the plume evolution at the sea surface and in depth. This alternative method could be integrated in a portable device for on-site analysis and multiplication of measurements for relevant results, or in a continuous flow analyser.     

Chromatographic separation of marine organic pollutants.

A review and discussion of the chromatographic separation of marine organic pollutants is given, including sampling and clean-up procedures, fractionation and enrichment of marine pollutants, capillary gas chromatography (cGC) and high-performance liquid chromatography applying both classical and chiral stationary phases. The potential of multi-dimensional cGC for the analysis of marine organic trace pollutants is discussed for polychlorinated biphenyls (PCBs). The chromatographic separation of coplanar PCBs and of the enantiomers of chiral pollutants provides a further insight into the toxic potential of these marine organic pollutants.     

Benefits of high resolution IC-ICP-MS for the routine analysis of inorganic and organic arsenic species in food products of marine and terrestrial origin

A recently developed and validated method for simultaneous determination of 17 inorganic and organic arsenic compounds in marine biota has been successfully applied to routine analysis of different food products, including fish, shellfish, edible algae, rice, and other types of grain. During one year, approximately 250 food samples were analyzed, mostly fish and rice. Long-term stability and robustness of the system was observed and reproducible results for certified reference materials were ensured by means of control charts. The separation was performed by ion-pair chromatography on an anion-exchange column to separate anionic, neutral, and cationic arsenic species in one chromatographic run. Hyphenation to ICP–MS allowed element-specific and sensitive detection of the different arsenic species with a detection limit as low as 8 ng As L^–1 in the sample extract, which is equivalent to 2 ng As g^–1 in the original sample. Special emphasis was laid on the analysis of marine algae and rice samples. These food types can contain elevated levels of the very toxic inorganic arsenic species (up to 90% in rice) and therefore are the focus of interest in the food industry. In marine algae, inorganic arsenic was mainly present as arsenate whereas in rice arsenite predominated.     

棒状薄层色谱-氢火焰离子探测仪检测老化沥青的四组分

沥青老化过程中四组分(饱和分、芳香分、胶质和沥青质)会发生变化,分析沥青在老化过程中四组分的变化有助于揭示沥青的老化机理,科学指导沥青材料的工程应用。分别采用薄膜烘箱试验(TFOT)、压力老化容器(PAV)试验和紫外光(UV)老化试验对沥青进行老化,利用棒状薄层色谱-氢火焰离子探测仪(TLC-FID)检测沥青老化前后的四组分,研究了扩展液组成对沥青四组分测定结果的影响,并与溶剂沉淀及色谱柱法(Corbett法)测定结果进行了对比。通过线性拟合分析了TLC-FID法与Corbett法检测老化沥青四组分的相关性。结果表明,采用二氯甲烷配制沥青溶液,以正庚烷为第一扩展液、甲苯/正庚烷(80:20, v/v)为第二扩展液、甲苯/乙醇(55:45, v/v)为第三扩展液,并利用TLC-FID方法检测老化沥青的四组分较为合适。该方法对于沥青四组分的分析及沥青老化机理的研究具有重要意义。     

Determination of tributyltin in marine sediment and waters by pressurised solvent extraction and liquid chromatography-tandem mass spectrometry

In this study, tributyltin (TBT) was extracted from marine sediment matrix with the use of pressurised solvent extraction (PSE), which uses high-temperature and -pressure conditions to increase extraction efficiency. The analyte was chromatographically resolved using a liquid chromatography-tandem mass spectrometry (LC-MS/MS) system with a pentafluorophenyl (PFP) column and a methanol/aqueous formic acid mobile phase gradient, and was detected by MS/MS as product fragments after collisionally induced dissociation (CID) of the cationic parent molecule. This study represents the first application of PSE extraction combined with LC-MS/MS analysis for the determination of TBT in sediments. The method has been validated according to the International Organisation for Standardisation (ISO) 17025:2001 and affords automated extraction of sediment samples with high-sensitivity analysis. The full method limit of detection was established as 1.25 ng Sn g^?1 with an instrument detection limit of 0.01 ng Sn g^?1. The chromatographic procedure may also be applied for the direct analysis of water matrices without the need for sample manipulation, and therefore represents a combined analytical approach for the monitoring of TBT contamination in marine or estuarine ecosystems.     

Polarographic study on the presence of antibiotics in food

EU and Italian laws dealing for the presence of antibiotics or, more in general, drags in food established limits for different kinds of food. Suitable rules exist about the medical treatment of cattle in relation to the production of milk and meat. The adoption of a procedure to check the respect of the law limits is necessary. In this paper, the presence of different classes of antibiotics in milk and in homogenised meat is investigated. Generally, HPLC methods are applied for this purpose. In this paper, the application of polarographic analysis is studied and the results are compared with the chromatographic ones. The comparison is relative to all the phases of analysis including the sample preparation. The results show the advantage of the proposed procedure.     

Rapid procedure for the isolation and analysis of fatty acid and fatty alcohol fractions from wax esters of marine zooplankton

A rapid and simple method for the isolation of fatty acid methyl esters and fatty alcohols from the lipid fraction of marine zooplankton is described. Wax esters are the dominant lipid class in most calanoid copepods and trans-esterification results in a high fatty alcohol content in the analytical extract. Current procedures for the separation and purification of lipid classes by preparative thin-layer chromatography are time-consuming and are subject to low recovery of the analytes. In this method, fatty acid methyl esters and fatty alcohols were separated by liquid chromatography using silica or honded amino-silica as the stationary phase. The procedure is equally applicable to the analysis of zooplankton with low wax ester (and hence fatty alcohol) content, for example, a number of species of euphausiid and, generally, for samples of low mass.     

Mycosporine-like amino acids in the marine dinoflagellate Gyrodinium dorsum: induction by ultraviolet irradiation

Cultures of the marine dinoflagellate Gyrodinium dorsum have been exposed to polychromatic radiation (photosynthetically active radiation and UV) from a solar simulator for up to 72 h. Different irradiance spectra in the ultraviolet are produced by inserting cut-off filters between lamp and samples. The mycosporine-like amino acid (MAA) content and composition are investigated by spectroscopic and chromatographic analysis. The study reveals that G. dorsum contains a complex mixture of several aminocyclohexenimine-MAAs and one aminocyclohexenone-MAA. UV irradiation around 320 nm induces an increase in the concentration of all MAAs in the samples. In contrast, exposure to short-wavelength UV-B radiation results in decreased overall MAA production. Furthermore, there is a spectral shift in the absorption of the MAA mixture towards shorter wavelengths, indicating that short-wavelength UV-B induces an altered MAA composition. The amount of MAAs is normalized to the chlorophyll a concentration.     

Kinetic analysis of the complex process of poly(vinyl alcohol) pyrolysis using a new coupled peak deconvolution method

A peak deconvolution procedure used for the analysis of data corresponding to simultaneous overlapping processes begins with separation of individual processes using functions such as Gaussian, Lorentzian, Weibull, and Fraser–Suzuki (FS) followed by application of kinetic analysis methods to the separated peaks. We propose a coupled peak deconvolution procedure to link the parameters of the FS functions of similar peaks in two DTG curves obtained at different linear heating rates, so that the coordinates of each peak can be obtained in a constrained manner. The proposed technique is a kinetic deconvolution method rather than a pure mathematical deconvolution technique. To analyze individual peaks in our study, the non-parametric kinetic and Freidman’s isoconversional methods have been applied to determine kinetic triplet of each process. This technique has been tested with both simulated and experimental data. Using this technique, the effects of molecular weight and degree of hydrolysis of polyvinyl alcohol (PVA) samples on reaction mechanism and activation energy of thermal degradation were studied. The presence of acetate group in the PVA samples causes thermal stability, decreases the rate of main reactions, and increases the activation energy. The results of this study may help tailor heat-resistant materials with proper choice of polymer characteristics.     

润滑油基础油烃族组成的薄层色谱法测定

采用薄层色谱-火焰离子化检测器测定了不同来源、不同工艺的润滑油基础油，提取了薄层色谱图特征变量，以偏最小二乘法为数学工具，通过洗脱色谱法取得基础数据，建立基础油的薄层色谱—烃族组成模型；采用该模型预测待测样品的烃族组成，并与洗脱色谱法的测定结果比较，饱和烃和芳烃质量分数的相关系数分别为0．9617和0．9611；对于分析结果进行：检验表明，建立的方法与洗脱色谱法的测定结果相一致；另外，薄层色谱法具有分析速度快，重复性好等优点。     

Liquid chromatography-electrospray ionisation-mass spectrometry based method for the simultaneous determination of algal and cyanobacterial toxins in phytoplankton from marine waters and lakes followed by tentative structural elucidation of microcystins

A liquid chromatography (LC)-based method with mass spectrometric (MS) detection was developed for simultaneous determination of various algal and cyanobacterial toxins extracted from phytoplankton occurring world-wide in marine waters and lakes. The method enables quantification of saxitoxin, anatoxin-A, domoic acid, nodularin, microcystins, okadaic acid and dinophysistoxin-1 with a single chromatographic run. In addition, the applied chromatographic conditions allow isolation and identification of substances suspected to be "new" microcystins (cyclic peptides) by fraction collection, hydrolysis, derivatisation of resulting free amino acids with the modified chiral Marfey's reagent N-alpha-(2,4-dinitro-5-fluorophenyl)-L-valinamide (L-FDVA) and enantioselective analysis of the amino acid derivatives by LC-ESI-MS.     

One Step Ultrasound Extraction and Purification Method for the Gas Chromatographic Analysis of Hydrocarbons from Marine Sediments: Application to the Monitoring of Italian Coasts

In this study, we describe the development of an ultrasound-assisted method for the simultaneous extraction and purification of hydrocarbons from marine sediments and then its application to the gas chromatographic analysis for the estimation of the biogenic anthropogenic and petrogenic sources of hydrocarbons present in marine sediments. The extraction of hydrocarbons and their simultaneous purification from other organic compounds present in sediments was performed by sonication of a three phase system consisting of sediment, hexane and a HCl medium at pH 2. This method allowed accurate recoveries of the hydrocarbon content in samples. In the following GC-FID analysis, we examined the hydrocarbon distribution in four different areas of the Italian seas determining the pristane to phytane ratio, the total odd n-alkanes to even n-alkanes ratio (carbon preference index), the low molecular weight to high molecular weight ratio, perylene content and the presence of the so called unresolved complex mixture; according to recent studies, these parameters support the identification of the biogenic, anthropogenic and petrogenic hydrocarbon sources present in environmental samples. GC chromatograms were then re-examined by means of two different statistical multivariate methods: two-dimensional mapping (2DMAP) and independent component analysis (ICA). 2DMAP showed the presence of a significant heterogeneity in the hydrocarbon composition of different areas and within samples of a same area. ICA confirmed the general heterogeneity evidenced by 2DMAP allowing in addition to characterise the hydrocarbon composition of one of the investigated areas.

     

Rapid characterization of anthocyanins in red raspberry fruit by high-performance liquid chromatography coupled to single quadrupole mass spectrometry

This paper describes the results of a comparison of four peak functions in describing real chromatographic peaks. They are the empirically transformed Gaussian, polynomial modified Gaussian, generalized exponentially modified Gaussian and hybrid function of Gaussian and truncated exponential functions. Real chromatographic peaks of different shapes (fronting. symmetric, and tailing) are obtained by various separation conditions of reversed-phase liquid chromatography. They are then fitted to the peak functions via the Marquardt-Levenberg algorithm, a nonlinear least-squares curve-fitting procedure, by Microsoft Solver. The qualities of the fits are evaluated by the sum of the squares of the residuals. It is concluded in the study that the empirically transformed Gaussian function offers the highest flexibility (best fits) to all shapes of chromatographic peaks, including extremely asymmetric tailing peaks with a peak asymmetry of up to 8. The flexibility of this function should improve our ability to process chromatographic peaks such as deconvolution of overlapped peaks and smoothing noisy peaks for the determination of statistical moments.     

Environmental monitoring approaches for the detection of organic contaminants in marine environments: A critical review

This review reports different approaches for monitoring the presence of organic contaminants in marine environments. From the traditional standard chromatographic methodologies coupled to different detectors to the recent advances in sensor technology, different strategies have been adopted by researchers aiming to provide more comprehensive, realistic and accurate environmental monitoring data sets. Reports on chemical analysis by different techniques of marine water and sediments, using grab and passive sampling techniques, are the most abundant in literature, showing relevant developments. Analysis of the marine biota (biomonitoring) has also been widely used as a proxy for the detection of organic chemicals in seawater, with bivalves being the most used as sentinel specie. Such biomonitoring can provide insights on bioavailability and bioaccumulation of organic pollutants, which is not possible to obtain by water and sediment analysis solely. Furthermore, effect-based methods are also presented as an important approach when it comes to obtain environmental meaningful data, such as potential toxicity and hazards posed by the complex chemical mixtures to local biota. This approach is reported to be a useful tool for screening areas without any previous knowledge on chemical composition, with subsequential qualitative and quantitative characterization being performed by chemical analysis. Finally, some of the most recent developments in sensor and biosensor technology for environmental purposes are also discussed, with some proof-of-concept studies showing promising results. However, further development and validations work is strongly advised prior to the use of those sensing platforms in real field trials.     

A new and fast extraction method for the determination of priority phenols from marine sediments by liquid chromatography

A new and fast method for the determination of priority phenols in marine sediment samples by high-performance liquid chromatography using microwave-assisted micellar extraction is optimized. This study is carried out using the nonionic surfactants polyoxyethylene 9 lauryl ether (polidocanol) and genapol X-080 as extractants. Parameters studied include surfactant concentration, solution pH, extraction time, and power. Once the method is optimized, it is applied to different spiked marine sediments from of the Canary Islands coastlines (Spain). The results obtained indicate that a power irradiation of 500 W for 2 min achieved the best extraction efficiency (approximately 100% recovery) and less than 10% relative standard deviation. Detection limits are obtained in the 2-20 microg/g range for the phenols studied. Finally, the proposed method provides a simple, fast, and organic solvent-free procedure to analyze phenols from marine sediment samples.     

Three-way principal component analysis of the volatile fraction by HS-SPME/GC of aceto balsamico tradizionale of modena

The present research is aimed at monitoring the evolution of the volatile organic compounds of different samples of aceto balsamico tradizionale of modena (ABTM) during ageing. The flavouring compounds, headspace fraction, of the vinegars of four batterie were sampled by solid phase microextraction technique (SPME), and successively analysed by gas chromatography. Obtaining a data set characterized by different sources of variability such as, different producers, samples of different age and chromatographic profile. The gas chromatographic signals were processed by a three-way data analysis method (Tucker3), which allows an easy visualisation of the data by furnishing a distinct set of graphs for each source of variability. The obtained results indicate that the samples can be separated according to their age highlighting the chemical constituents, which play a major role for their differentiation. The present study represents an example of how the application of Tucker3 models, on gas chromatographic signals may help to follow the transformation processes of food products.     

On the equations describing chromatographic peaks and the problem of the deconvolution of overlapped peaks

The problem of the appropriate choice of the function that describes a chromatographic peak is examined in combination with the deconvolution of overlapped peaks by means of the non-linear least-squares method. It is shown that the majority of the functions proposed in the literature to describe chromatographic peaks are not suitable for this purpose. Only the polynomial modified Gaussian function can describe almost every peak but it is mathematically incorrect unless it is redefined properly. Two new functions are proposed and discussed. It is also shown that the deconvolution of an overlapping peak can be done with high accuracy using a non-linear least-squares procedure, like Microsoft Solver, but this target is attained only if we use as fitted parameters the position of the peak maximum and the peak area (or height) of every component in the unresolved chromatographic peak. In case we use as fitted parameters all the parameters that describe each single peak enclosed in the multi-component peak, then Solver leads to better fits, which though do not correspond to the best deconvolution of the peak. Finally, it is found that Solver gives much better results than those of modern methods, like the immune and genetic algorithms.