Comparative analysis of the atomic structure of crystalline and amorphous PbTiO<Subscript>3</Subscript> on the basis of the molecular-dynamics simulation data

Models of the atomic structure of PbTiO₃ in the crystalline and amorphous states have been constructed by the molecular-dynamics method. The distances between positively charged Pb and Ti ions, which are significantly different in PbTiO₃ crystals, are averaged in the amorphous material, forming a common peak in the radial distribution function.     

Rapid crystallization of silicon films using Joule heating of metal films

50-nm thick amorphous silicon films formed on glass substrates were crystallized by rapid Joule heating induced by an electrical current flowing in 100-nm-thick Cr strips formed adjacently to 200-nm-thick SiO₂ intermediate layers. 3-μs-pulsed voltages were applied to the Cr strips. Melting of the Cr strips caused a high Joule heating intensity of about 1×10⁶ W/cm². Raman scattering measurements revealed complete crystallization of the silicon films at a Joule heating energy of 1.9 J/cm² via the SiO₂ intermediate layer. Transmission electron microscopy measurements confirmed a crystalline grain size of 50–100 nm. 1-μm-long crystalline grain growth was also observed just beneath the edge of the Cr strips. The electrical conductivity increased from 10^-5 S/cm to 0.3 S/cm for 7×10¹⁷-cm^-3-phosphorus-doped silicon films because of activation of the phosphorus atoms because of crystallization. The numerical analysis showed a density of localized defect states at the mid gap of 8.0×10¹⁷ cm^-3. Oxygen plasma treatment at 250 °C and 100 W for 5 min reduced the density of the defect states to 2.7×10¹⁷ cm^-3. Received: 3 April 2001 / Accepted: 9 April 2001 / Published online: 25 July 2001     

Photoluminescence of crystalline and disordered BTO:Mn powder: Experimental and theoretical modeling

Disordered and crystalline Mn-doped BaTiO₃ (BTO:Mn) powders were synthesized by the polymeric precursor method. After heat treatment, the nature of visible photoluminescence (PL) at room temperature in amorphous BTO:Mn was discussed, considering results of experimental and theoretical studies. X-ray diffraction (XRD), PL, and UV-vis were used to characterize this material. Rietveld refinement of the BTO:Mn from XRD data was used to built two models, which represent the crystalline BTO:Mn (BTO:Mn_c) and disordered BTO:Mn (BTO:Mn_d) structures. Theses models were analyzed by the periodic ab initio quantum mechanical calculations using the CRYSTAL98 package within the framework of density functional theory at the B3LYP level. The experimental and theoretical results indicated that PL is related with the degree of disorder in the BTO:Mn powders and also suggests the presence of localized states in the disordered structure.     

Photoluminescence in amorphous TiO2-PbO systems

Photoluminescence (PL) at room temperature has been achieved in amorphous thin films and powders of the TiO₂–PbO system. They were prepared by the polymeric precursor method with [PbO]/[TiO₂] molar ratios ranging from 0.0 to 1.0. The energy position of maximum PL emission and the PL intensity showed dependence on Pb concentration. The Pb addition suggests an increase in the number of non-bridging oxygens (NBO) in the amorphous TiO₂ network. These results support the relationship between photoluminescence and structure in TiO₂-based amorphous materials. Received: 7 February 2001 / Accepted: 8 February 2001 / Published online: 27 June 2001     

Current instabilities in dynamic random access memory storage capacitor formed with electron beam deposited Y2O3 dielectric

Metal-oxide-semiconductor (MOS) storage capacitors based on electron beam deposited Y₂O₃ extrinsic dielectric on Si show changes in capacitance density depending on the amorphous and crystalline phases. Bias stress cycle-dependent changes in capacitance density occur due to the non-equilibrium nature of defect states at the Y₂O₃/Si interface after O₂ annealing as a result of the emergence of a 4–8 nm thick SiO₂ film at the interface. Leakage currents show instability under repeated dc bias stress, the nature and extent of which depend upon the structure of the Y₂O₃ gate dielectric and the polarity of dc bias. With amorphous Y₂O₃, leakage currents drift to lower values under gate injection due to electron trapping, and to higher values under Si-injection due to the generation of holes. Though leakage current drift is minimal for crystalline Y₂O₃, its magnitude increases as the energy of injected electrons from mid-gap states is low and the local field due to asperity is high. The emergence of interfacial SiO₂ reduces the magnitude of Si-injection leakage current substantially, but causes transient changes resulting in switching to higher values at a threshold dc bias. Thermal detrapping of holes and reverse bias stress studies confirm that the instability of current is caused by an increase in the cathodic field from hole trapping at interface states. Leakage current instability limits the application of extrinsic high dielectric constant dielectrics in a high density DRAM storage capacitor, unless a new interface layer scheme other than SiO₂ and a method to form a defect-free dielectric layer can be implemented. Received: 29 October 2001 / Accepted: 22 April 2002 / Published online: 4 December 2002 RID="*" ID="*"Corresponding author. Fax: +1-413/545-4611, E-mail: rastogi@ecs.umass.edu     

Large-scale synthesis of crystalline β-SiC nanowires

Large quantities of high-purity crystalline β-SiC nanowires have been synthesized at relatively low temperature via a new simple method, the chemical-vapor-reaction approach, in a home-made graphite reaction cell. A mixture of milled Si and SiC powders and C₃H₆ were employed as the starting materials. The results show that the nanowires with diameters of about 10–35 nm are single crystalline β-SiCwithout any wrapping of amorphous material, and the nanowire axes lie along the 〈111〉 direction. Some unique properties are found in the Raman scattering from the β-SiC nanowires, which are different from previous observations of β-SiC materials. A possible growth mechanism for the β-SiC nanowires is proposed. Received: 27 August 2002 / Accepted: 28 August 2002 / Published online: 4 December 2002 RID="*" ID="*"Corresponding author. Fax: +86-29/8491-000, E-mail: zjli-sohu@sohu.com     

Strong ultraviolet and violet photoluminescence from Si-based anodic porous alumina films

We have investigated photoluminescence (PL) from Si-based anodic porous alumina films formed by real-time controlled anodization of electron-beam evaporated Al films. As-anodized samples show three strong PL bands at 295, 340, and 395 nm. These bands blueshift and their intensities decrease after the samples are annealed. When the annealing temperature increases to 1000 °C, the blueshift becomes specially pronounced and meanwhile the structures of the films develop toward crystalline Al₂O₃. Based on discussions on the thermal annealing behaviors of the PL and PL excitation spectra, we suggest that optical transitions in oxygen-related defects, F⁺ (oxygen vacancy with one electron) centers, are responsible for the observed ultraviolet and violet PL. Received: 24 July 2000 / Accepted: 24 February 2001 / Published online: 3 May 2001     

Raman characterization of H:LiNbO3 waveguides

In this work we present polarized Raman measurements of z-cut multimode H:LiNbO₃ waveguides in the κ_i- and β_i-phase states. A spectrum with unexpected form and behaviour, originating from the layer at the very surface, was observed in samples with various degrees of Li–H substitution. Possible reasons for the presence of this strange spectrum are considered. Received: 16 May 2001 / Revised version: 7 August 2001 / Published online: 23 October 2001     

Room-temperature photoluminescence in amorphous SrTiO3– the influence of acceptor-type dopants

Room-temperature photoluminescence (PL) was observed in undoped and 2 mol % Cr-, Al- and Y-doped amorphous SrTiO₃ thin films. Doping increased the PL, and in the case of Cr significantly reduced the associated PL wavelength. The optical bandgaps, calculated by means of UV–vis absorption spectra, increased with crystallinity and decreased with the doping level. It was considered that yttrium and aluminum substituted Sr²⁺, whereas chromium replaced Ti⁴⁺. It is believed that luminescence centers are oxygen-deficient BO₆ complexes, or the same centers with some other defects, such as oxygen or strontium vacancies, or BO₆ complexes with some other defects placed in their neighborhood. The character of excitation and the competition for negatively charged non-bridging oxygen (NBO) among numerous types of BO₆ defect complexes in doped SrTiO₃ results in various broadband luminescence peak positions. The results herein reported are an indicative that amorphous titanates are sensitive to doping, which is important for the control of the electro-optic properties of these materials. The probable incorporation of Cr into the Ti site suggests that the existence of a double network former can lead to materials displaying a more intense photoluminescence. Received: 20 November 2001 / Accepted: 22 November 2001 / Published online: 27 March 2002     

多晶铁电薄膜的相变——应力和晶粒尺寸效应

用掠入射X射线衍射法观察到钛酸铅多晶铁电薄膜表面层与体内的相变温度不同,表面层的结构参数也有异于体内;唯象地把多晶铁电薄膜抽象为一个表面层为细晶粒、低应变层,体内为粗晶粒、高应变层的两层结构,根据应力和晶粒尺寸效应对铁电相变的影响,解释了钛酸铅多晶铁电薄膜的相变特征 关键词：     

Laser–MBE growth of high-quality ZnO thin films on Al2O3(0001) and SiO2/Si(100) using the third harmonics of a Nd:YAG laser

High-quality ZnO thin films were grown on single-crystalline Al₂O₃(0001) and amorphous SiO₂/Si(100) substrates at 400–640 °C using laser molecular beam epitaxy. For film growth, the third harmonics of a pulsed Nd:YAG laser were illuminated on a ZnO target. The ZnO films were epitaxially grown on Al₂O₃(0001) with the narrow X-ray diffraction full width at half maximum (FWHM) of 0.04° and the films on SiO₂/Si(100) exhibited a preferred c-axis orientation. Furthermore, the films exhibited excellent optical properties in photoluminescence (PL) measurements with very sharp excitonic and weak deep-level emission peaks. At 15 K, PL FWHM values of the films grown on Al₂O₃(0001) and SiO₂/Si(100) were 3 and 18 meV, respectively. Received: 8 May 2001 / Accepted: 18 September 2001 / Published online: 20 December 2001     

Structural and optical properties of Si/SiO2 multi-quantum wells

Structural and optical properties of Si/SiO₂ multi-quantum wells (MQW) were investigated by means of Raman scattering and photoluminescence (PL) spectroscopy. The MQW structures were fabricated on a quartz substrate by remote plasma enhanced chemical vapour deposition (RPECVD) of alternating amorphous Si and SiO₂ layers. After layer deposition the samples were subjected to heat treatments, i.e. rapid thermal annealing (RTA) and furnace annealing. Distinct PL signatures of confined carriers evidenced formation of Si-nanocrystals (nc-Si) in annealed samples. Analyses of Raman spectra also show presence of nc-Si phase along with amorphous-Si (a-Si) phase in the samples. The strong influence of the annealing parameters on the formation of nc-Si phase suggests broad possibilities in engineering MQW with various optical properties. Interestingly, conversion of the a-Si phase to the nc-Si phase saturates after certain time of furnace annealing. On the other hand, thinner Si layers showed a disproportionately lower crystalline volume fraction. From the obtained results we could assume that an interface strain prevents full crystallization of the Si layers and that the strain is larger for thinner Si layers. The anomalous dependence of nc-Si Raman scattering peak position on deposited layer thickness observed in our experiments also supports the above assumption.     

Effect of growth time on the structure, Raman shift and photoluminescence of Al and Sb codoped ZnO nanorod ordered array thin films

Al and Sb codoped ZnO nanorod ordered array thin films have been deposited on glass substrate with a ZnO seed layer by hydrothermal method at different growth time. The effect of growth time on structure, Raman shift, and photoluminescence (PL) was studied. The thin films at growth time of 5 h consist of nanorods growth vertically oriented with ZnO seed layer, and the nanorods with an average diameter of 27.8 nm and a length of 1.02 μm consist of single crystalline wurtzite ZnO crystal and grow along [0 0 1] direction. Raman scattering analysis demonstrates that the thin films at the growth time of 5 h have great Raman shift of 15 cm⁻¹ to lower wavenumber and have low asymmetrical factor Г_a/Г_b of 1.17. Room temperature photoluminescence reveals that there is more donor-related PL in films with growth time of 5 h.     

Fabrication and annealing effects of SnO2/SiOx nanocables sheathed by the sputtering technique

We reported an approach, in which we have produced the nano-sized crystalline tin oxide (SnO₂) particles with rutile structure. SnO₂ nanowires were coated with a shell layer of SiO_x via a sputtering method. Transmission electron microscopy and elemental mapping investigations revealed that the nanostructures consisted of a crystalline SnO₂ core surrounded by an amorphous SiO_x sheath. The annealing effects on the core-shell nanowires were investigated, revealing that the outer surface became rougher by the thermal annealing. For core-shell nanowires, a room-temperature PL measurement with a Gaussian fitting showed yellow, blue, and violet light emission bands, with the relative intensity of the yellow band showing an increase after thermal annealing. Possible PL emission mechanisms are discussed. This study reveals that the sputtering is effective for preparing the shell layers of nanocables.     

Laser crystallization of amorphous silicon films investigated by Raman spectroscopy and atomic force microscopy

The intrinsic and phosphorous (P)-doped hydrogenated amorphous silicon thin films were crystallized by laser annealing. The structural properties during crystallization process can be investigated. Observed redshifts of the Si Raman transverse optical phonon peak indicate tensile stress present in the films and become intense with the effect of doping, which can be relieved in P-doped films by introducing buffer layer structures. Based on experimental results, the established correlation between the stress and crystalline fraction (X_C) suggests that the relatively high stress can limit the increase in X_C and the highest crystalline fraction is obtained by a considerable stress release. At high laser energy density of 1250 mJ/cm², the poorer crystalline quality and disordered structure of the film originating from the irradiation damage and defects lead to the low electron mobility.     

Structural and optical properties of thin films porous amorphous silicon carbide formed by Ag-assisted photochemical etching

In this work, we present the formation of porous layers on hydrogenated amorphous SiC (a-SiC: H) by Ag-assisted photochemical etching using HF/K₂S₂O₈ solution under UV illumination at 254 nm wavelength. The amorphous films a-SiC: H were elaborated by d.c. magnetron sputtering using a hot pressed polycrystalline 6H-SiC target. Because of the high resistivity of the SiC layer, around 1.6 MΩ cm and in order to facilitate the chemical etching, a thin metallic film of high purity silver (Ag) has been deposited under vacuum onto the thin a-SiC: H layer. The etched surface was characterized by scanning electron microscopy, secondary ion mass spectroscopy, infrared spectroscopy and photoluminescence. The results show that the morphology of etched a-SiC: H surface evolves with etching time. For an etching time of 20 min the surface presents a hemispherical crater, indicating that the porous SiC layer is perforated. Photoluminescence characterization of etched a-SiC: H samples for 20 min shows a high and an intense blue PL, whereas it has been shown that the PL decreases for higher etching time. Finally, a dissolution mechanism of the silicon carbide in 1HF/1K₂S₂O₈ solution has been proposed.     

Quantum emission efficiency of nanocrystalline and amorphous Si quantum dots

The paper presents the comparison of emission efficiencies for crystalline Si quantum dots (QDs) and amorphous Si nanoclusters (QDs) embedded in hydrogenated amorphous (a-Si:H) films grown by the hot wire-CVD method (HW-CVD) at the variation of technological parameters. The correlations between the intensities of different PL bands and the volumes of Si nanocrystals (nc-Si:H) and/or an amorphous (a-Si:H) phase have been revealed using X-ray diffraction (XRD) and photoluminescence (PL) methods. These correlations permit to discuss the PL mechanisms in a-Si:H films with embedded nc-Si QDs. The QD parameters of nc-Si:H and a-Si:H QDs have been estimated from PL results and have been compared (for nc-Si QDs) with the parameters obtained by the XRD method. Using PL and XRD results the relations between quantum emission efficiencies for crystalline (η_cr) and amorphous (η_am) QDs have been estimated and discussed for all studied QD samples. It is revealed that a-Si:H films prepared by HW-CVD with the variation of wire temperatures are characterized by better passivation of nonradiative recombination centers in comparison with the films prepared at the variation of substrate temperatures or oxygen flows.     

Interface reactions in [Fe/B]<Subscript>n</Subscript> multilayers: a way to tune from crystalline/amorphous layer sequences to homogeneous amorphous Fe<Subscript>x</Subscript>B<Subscript>100-x</Subscript> films

[Fe/B]_{n ≥2} multilayers were prepared by thermal evaporation, ion-beam sputtering and laser ablation. By applying in situ electron spectroscopies (UPS, XPS) and monitoring the electrical resistance during layer growth, evidence could be provided for the occurrence of interface reactions within the range of studied deposition temperatures (77 K ≤T ≤300 K). These reactions result in amorphous Fe_xB_100-x phases, which are spatially restricted to a width of less than 3 nm at the original interface. The amorphicity of the reacted interlayers was unequivocally proven by additional high-resolution electron microscopy (HRTEM) and their characteristically changed magnetic properties. Due to the well-defined width of the interface reaction, homogeneous amorphous Fe_xB_100-x films can be obtained by reducing the individual Fe and B layer thicknesses to below the above reaction depth, while for larger thicknesses layer sequences of the crystalline/amorphous/crystalline type will result. Received: 30 January 2002 / Accepted: 31 January 2002 / Published online: 10 September 2002 RID="*" ID="*"Corresponding author. Fax: +49-731/502-2963, E-mail: hans-gerd.boyen@physik.uni-ulm.de     

Patterning of amorphous and polycrystalline Ni78B14Si8 with a focused-ion-beam

The machining response of amorphous and crystalline Ni₇₈B₁₄Si₈ was investigated when structuring substrates using focused-ion-beam (FIB) milling. In particular, the sputtering yield as a function of the scan speed, and the effects of ion fluence and scan speed on the milled depth were studied. The ion fluence dependent evolution of the cross-sectional profiles of trenches was examined by atomic force microscopy (AFM). When milling amorphous Ni₇₈B₁₄Si₈, it was found that the sputtering yield first decreased with increasing the beam scan speed, then kept constant within the scan speed range, up to 710 nm/s, investigated in this work; it was also found that the milled depth was almost proportional to the ion beam fluence. The patterning of polycrystalline Ni₇₈B₁₄Si₈ resulted in anisotropic milling-rates due to the varying orientation of the grains in the material. The analysis of the profile evolution in both materials indicated that the surface finish of trenches was scan speed, ion beam fluence and scan strategy dependent. The study demonstrated that direct patterning by FIB could be used for producing masters in amorphous Ni-based alloys for injection moulding and hot embossing.     

Photoluminescence and Raman spectra of the ordered vacancy compound CuGa5Se8

We studied the photoluminescence (PL) and Raman properties of the ordered defect compound CuGa₅Se₈. Twelve peaks were detected from the room-temperature Raman spectra with the A₁ mode around 160 cm⁻¹. Due to the stress in the polycrystalline thin film the corresponding frequencies of the Raman modes of a CuGa₅Se₈ single crystal were slightly shifted. One broad asymmetric PL band at 1.788 and 1.765 eV was observed at 10 K in the PL spectra of CuGa₅Se₈ single crystal and polycrystalline layer, respectively. The temperature and laser power dependencies of the PL spectra were also studied. The shape and properties of the PL band assure the presence of potential fluctuations and the analyses of the PL data suggest that the emission is due to band-to-tail (BT) or band-to-impurity (BI) recombination.