环氧大豆油多元醇改性磺酸型水性聚氨酯合成与性能研究

用2-乙基己醇(异辛醇)对环氧大豆油进行开环,生成环氧大豆油多元醇,并利用其对由异佛尔酮二异氰酸酯(IPDI)、聚己内酯二元醇(PCL)和乙二胺基乙磺酸钠(AAS)为主要合成原料的磺酸型水性聚氨酯(SWPU)进行改性,考察了不同多元醇含量对磺酸型水性聚氨酯乳液以及胶膜性能的影响.首先,通过FTIR和1H-NMR证实了环氧大豆油多元醇的合成;然后经过粒径测试、耐水性测试、接触角测试、机械性能测试、TG测试等检测表明:磺酸型水性聚氨酯成功合成,随着多元醇含量的增加,水性聚氨酯乳液粒径逐渐增大;胶膜的吸水率逐渐减小,并趋于平缓;力学性能拉伸强度逐渐增强,而断裂伸长率下降.但当环氧大豆油多元醇添加量过大时,导致最后乳液无法分散,乳化失败.当多元醇含量与PCL质量比为0.2时,胶膜吸水率由50.14%减小至12.27%,接触角为103.3°,拉伸强度由8.16 MPa增至21.77 MPa.通过TG表明,分子结构中多元醇的引入,胶膜的耐热性有明显提高.     

甲基丙烯酸羟乙酯改性水性聚氨酯乳液的制备及性能

采用种子溶胀乳液聚合法,以水性聚氨酯为种子,甲基丙烯酸羟乙酯、甲基丙烯酸甲酯和丙烯酸丁酯为单体制备水性聚氨酯丙烯酸酯复合乳液,考察了甲基丙烯酸羟乙酯含量对复合乳液的T型剥离、胶膜的硬度、耐水性和力学性能的影响。结果表明,随着甲基丙烯酸羟乙酯含量的增加,复合乳液的T型剥离强度、胶膜的硬度和拉伸强度增大,胶膜的耐水性先增大后减小,断裂伸长率有所降低,适宜的甲基丙烯酸羟乙酯用量为3%。     

中和度对聚酯型阴离子水性聚氨酯性能的影响

采用预聚体法,以聚酯多元醇、甲苯二异氰酸酯、二羟甲基丙酸（DMPA）制备了聚酯型阴离子水性聚氨酯乳液,考察了中和度对乳液的粒径、运动黏度以及胶膜力学性能的影响。结果表明,随着中和度的增加,水性聚氨酯乳液的粒径减小;运动黏度增大;水性聚氨酯胶膜的耐水性先增大后减小;胶膜的拉伸强度提高,但其断裂伸长率降低。以三乙胺为中和剂...     

高性能水性聚氨酯研究进展

综述了近几年水性聚氨酯高性能化研究进展,从多元醇分子设计、硅氧烷改性、纳米复合、可再生资源利用、交联固化等方面进行了综述.电子包装材料利用磺化多元醇提高涂膜断裂伸长率并降低表面电阻为10×1010Ω/cm2,粘合剂应用引入聚二丁烯多元醇提高涂膜耐水性和粘接强度;织物整理引入氟化聚醚多元醇提升棉织物耐水性,表面接触角达到147°;采用特殊二元醇合成新型聚酯多醇改进涂膜耐水性的同时获得高模量和拉伸强度;含羧基聚己内酯二醇可降低水性聚氨酯乳液粒径到20nm以下;采用端羟基聚二甲基硅氧烷降低涂膜吸水率和表面能,使成膜接触角迅速增加;将碳纳米管、蒙脱土、绿坡缕石和多面体倍半硅氧烷等经有机化改性进行纳米原位复合,提升材料力学性能;利用可再生资源进行物理共混提升力学性能同时达到可降解目的;成膜过程引入环氧改性和交联改性,提高涂膜硬度、耐溶剂性和耐水性.     

水性聚氨酯结构与胶膜性能的关系

为制备一种性能优异的水性聚氨酯涂层,以聚丙二醇和异佛尔酮二异氰酸酯为主要原料,用本体聚合法制备了水性聚氨酯,考察了结构组元对胶膜性能的影响,并用激光粒度仪、微机控制电子万能试验机和同步热分析仪进行了表征。结果表明:当硬段含量增加时,乳液粒径增大,胶膜拉伸强度增加,吸水率升高;当异氰酸根指数增大时,乳液粒径增大,胶膜拉伸强度增加,吸水率降低;当亲水性扩链剂含量和中和度增大时,乳液粒径减小,胶膜的拉伸强度增加,吸水率升高;在硬段比例为50%、异氰酸酯指数为1.35、亲水性扩链剂含量为5%、中和度为1的条件下,胶膜性能较佳(拉伸强度为16MPa,断裂伸长率为556%,吸水率为6.2%)且在丙酮和甲苯中均表现出溶胀现象。     

丙烯酸酯改性水性聚氨酯/纳米二氧化硅复合材料的制备和性能

利用原位聚合伴随溶胶-凝胶进行的过程,合成了丙烯酸酯改性聚氨酯(PUA)/纳米SiO₂(PUAS)复合乳液。 通过纳米粒度仪、扫描电子显微镜、透射电子显微镜和热重分析仪等技术手段表征了复合乳液及胶膜的结构和性能。 结果表明,纳米SiO₂能够均匀地分散在复合材料中,随着原料中前驱体正硅酸乙酯(TEOS)质量分数的增加,复合乳液粒径有所增大,胶膜力学性能和热稳定性明显提高。 当TEOS质量分数为8%,胶膜拉伸强度达到16.8 MPa,邵氏硬度A达到94,最大分解速率温度提高到416 ℃,且胶膜耐水性明显改善,吸水率降低到2.1%。     

软段含离子的含氟水性聚氨酯的制备

以单羟基氟碳链一元醇为有机氟改性剂,将含氟基团引入聚氨酯主链中,通过分子设计的方法制备出软段含有离子基团的有机氟阴离子型水性聚氨酯。 比较了传统水性聚氨酯、硬段含氟的水性聚氨酯和软段含氟的水性聚氨酯在合成方法、耐水性、 热稳定性以及结晶性方面的差异;实验证明了软段含氟聚氨酯的水性聚氨酯的性能最为优良。 通过红外光谱的表征确定了氟化聚氨酯的结构,并证明了含氟基团的引入对聚氨酯软硬段间氢键作用的影响;水接触角由73°增加至107°,吸水溶胀率降低了66%,胶膜耐水性提高;热重分析结果表明,含氟聚氨酯的最大热失重温度提高了30 ℃,热稳定性增加;广角X射线衍射结果表明,胶膜的结晶度增加,结晶形式发生了微小程度的转变;扫描电子显微镜结果证明存在不均匀的多相结构。     

单油酸三羟甲基丙烷酯改性水性聚氨酯

利用单油酸三羟甲基丙烷酯(TMPM)、异佛尔酮二异氰酸酯(IPDI)和聚氧化丙烯(PPG)等制备水性聚氨酯。采用透射电镜(TEM)、动态激光光散射(DLLS)、红外光谱(FT-IR)、热重分析(TGA)和表面张力仪表征了乳液胶束形态、产物结构及性能。结果表明:水性聚氨酯(PU)分子上引入脂肪侧链容易在水中形成规整的胶束,但TMPM改性的水性聚氨酯胶束粒径随TMPM含量的增加不断增大,当w(TMPM)=0.07时,乳液不稳定;脂肪侧链的引入降低了水性聚氨酯乳液的表面张力,表面张力随着反应体系中—NCO和—OH摩尔比的增大而降低,随交联度的增大先增加后减小;TMPM的引入可以提高胶膜的热稳定性。     

软段对水性聚氨酯结构与性能的影响

以低聚物多元醇、异氟尔酮二异氰酸酯(IPDI)、亲水单体二羟甲基丙酸(DMPA),乙二胺为主要原料,制备了一组不同组成的聚氨酯乳液。通过粘度测定、粒度分析、力学性能和耐水性能测试、原子力显微镜(AFM)分析,研究了软段类型、软段分子量对乳液及其胶膜性能的影响。结果表明,分子结构规整、易结晶的软段合成的聚氨酯树脂力学性能和耐水性能都较好,对聚己二酸酯而言,分子量减小,其合成的水性聚氨酯拉伸强度提高,耐水性能却有很大程度的下降。     

PCDL型超支化水性聚氨酯的合成与性能

以甲苯-2,4-二异氰酸酯（TDI）、聚碳酸酯二醇（PCDL）、二羟甲基丙酸（DMPA）和二乙醇胺（DEOA）为原料,采用A₂＋bB₂共聚合路线合成了具有超支化结构的水性聚氨酯（HBAPU）乳液。采用红外光谱（FT-IR）、核磁共振（13C NMR）对产物结构进行了表征,证实了超支化聚氨酯的支化度随 n(NCO)/n(OH)比值的增大而增大。用PCS、TG、电子拉力机对产物的性能进行了测试,同时也对胶膜的耐水性进行了测试,发现在DMPA含量为0.4 mmol/g时,HBAPU的粒径仅有20.57 nm,而线性水性聚氨酯粒径有130.91 nm,并且HBAPU具有良好的耐水性、热稳定性和较高的拉伸强度。     

基于CuAAC反应链间自交联有机-无机杂化水性聚氨酯的合成及性能

利用4,4’-二羟甲基-1,4-庚二炔功能单体作为扩链剂合成了一系列炔基接枝量不同的水性聚氨酯（WPU）,然后基于铜催化的叠氮-炔基环加成（CuAAC）反应,采用3-叠氮基丙基三乙氧基硅烷（APTES-N₃）改性炔基功能化WPU,制备了室温链间自交联有机-无机杂化WPU. 采用红外光谱（FTIR）和核磁氢谱（¹H NMR）表征了自交联有机-无机杂化WPU. 探讨了APTES-N₃接枝量对WPU膜性能和WPU乳液形态的影响. 结果表明,随着APTES-N₃含量增加,WPU膜的结晶性逐渐下降;耐水性、耐溶剂性和热稳定性逐渐增强;WPU乳液粒子黏连程度增加. 当APTES-N₃质量分数从0增大到12%时,WPU膜的拉伸强度从14.3 MPa增加到28.6 MPa.     

Synthesis of a biobased waterborne polyurethane with epichlorohydrin-modified lignin

Abstract

A series of lignin-based waterborne polyurethanes (ELWPUs) are prepared using epichlorohydrin-modified lignin (ELG) as the biobased component. The effect of ELG dosage on the performance of the dispersions was studied by particle sizing. The morphology, crystallinity, thermal behavior, water resistance and mechanical properties of the films were investigated as well. The results show that the particle size of ELWPU dispersions increased with the addition of ELG. Furthermore, the ELWPU exhibited noticeable thermal stability, desired mechanical properties and water resistance as the tensile strength of ELWPU film containing 0.25?wt% ELG increased to 40.6?MPa from 15.2?MPa and the water absorption rate decreased from 20.1 to 12.4% compared to the non-modified waterborne polyurethane. The ELG played an important role in improving the properties of the biomass-based materials.     

环氧改性水性聚氨酯乳液的制备及其膜性能

以聚己内酯二元醇(CAPA)为软段,异佛尔酮二异氰酸酯(IPDI)和六亚甲基二异氰酸酯(HDI)为硬段,环氧树脂E-44为大分子交联剂,经相转化法合成了一系列环氧树脂改性负离子水性聚氨酯(EPPU)自乳化乳液,并制备了改性水性聚氨酯的固化膜.通过FTIR、TGA及接触角、力学性能测试对聚合物结构及其膜性能进行了研究.通过原子力显微镜(AFM)观察膜表面形态和表面粗糙度.乳液粒径及粒径分布通过动态激光光散射法(DLLS)测定.FTIR分析表明环氧树脂的羟基和环氧基都参与了发应.TGA表明,环氧树脂的加入可以提高聚氨酯的热稳定性.随着w(E-44)增大,改性聚氨酯膜的拉伸强度得到改善,断裂伸长率减小.随着w(E-44)增大,乳液粒径增大,薄膜的接触角增大,改性后的PU膜表面光滑度下降,拒水性增强.     

Effect of 3-Aminopropyltriethoxysilane on Solvent Resistance,Thermal Stability,and Mechanical Properties of Two-Component Waterborne Polyurethane

A two-component waterborne polyurethane (2K-WPU) was obtained by the reaction between a hydroxyl-component waterborne polyurethane and a hydrophilically modified polyisocyanate. A hydroxyl-component waterborne polyurethane with a cross-link structure of Si-O-Si groups was synthesized by means of 3-aminopropyltriethoxysilane (APTES) and trimethylolpropane end-capping concurrently. Mean particle size and viscosity of the hydroxyl-component WPU mini-emulsions were examined by a laser particle analyzer and a Brookfield viscometer. Fourier transform-infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS) were utilized to analyze the chemical structure of 2K-WPU films. The influence of APTES content on thermal stability, mechanical properties, and solvent resistance of 2K-WPU films was also investigated by thermogravimetric analysis (TGA), a universal testing machine, and an immersion test under three kinds of solvent (ethanol, acetone, and dichloromethane) for 24 h, respectively. The results show that 2K-WPU films containing APTES have excellent thermal stability, tensile strength, and breaking elongation. Additionally, these films possess the strongest resistance to ethanol, as well as resistance to acetone and dichloromethane to a certain extent at the APTES content of 4 wt.%.     

丝胶接枝水性聚氨酯乳液对天然乳胶的改性研究

利用丝胶优良的生物相容性、抗氧化性等特点,结合水性聚氨酯优良的机械性能,合成了丝胶接枝水性聚氨酯乳液(1)。采用杂凝聚技术用1改善天然乳胶手套的机械性能和过敏性。结果表明,经1改性后的天然乳胶手套在断裂伸长率基本不变的情况下,断裂强度有了明显的提高;杂凝聚方法形成的核壳结构使丝胶包裹在手套的内表面,达到了改善过敏性的目的。     

Preparation of waterborne polyurethane nanocomposites: Polymerization from functionalized hydroxyapatite

We report the preparation and characterization of waterborne polyurethane (WBPU)/hydroxyapatite (HAp) nanocomposites through in situ polymerization from functionalized HAp. The HAp nanoparticles (HAp NPs) were urethanated with 3-isocyanatemethyl-3,5,5-trimethyl-cyclohexylisocyanate (isophorone diisocyanate) to obtain grafted HAp NPs containing isocyanate groups (HAp-g-NCO) as crosslinkers and then the HAp-g-NCO is further polymerized with WBPU monomers to form the WBPU/HAp nanocomposites. The HAp NPs were homogeneously dispersed in the polyurethane matrix at low loading levels (?2.0 wt%), thus the mechanical strength and the elongation at break of the WBPU/HAp nanocomposites were significantly improved. Thermal stability and water resistance of the WBPU/HAp nanocomposites are also enhanced. These results suggest that the WBPU/HAp nanocomposites prepared by in situ polymerization hold the potential as new materials with improved mechanical properties, thermal stability and water resistance.     

Microstructure and Properties of Triethoxysilylpropylamine-Capped Polyurethane/Titania Hybrid Films

Triethoxysilylpropylamine-capped waterborne polyurethane/titania hybrid films were prepared by in situ method via sol-gel process of titanium n-butoxide under acidic condition. In the paper, we studied the effect of the contents of titania sol on the microstructure, mechanical property, water resistance, and optical property of the hybrid films. It was found, with introducing the content of titania, some physical properties such as tensile strength, modulus, water resistance, refractive index, heat resistance, and ultraviolet absorbance will increase. SEM and SAXS study suggested that the hybrid films had good planarization.     

Synthesis and Characterization of New Self-Colored Blue Waterborne Polyurethane Based on a Colorant Diol as Chain Extender

A series of novel self-colored blue waterborne polyurethanes (BPUs) were successfully synthesized by incorporating a self-made colored diol 1,4-bis(2-hydroethylamino)anthrancene-9,10-dione (BHAD) into the polyurethane backbone via step growth polymerization. FTIR, ¹H NMR, ultraviolet-visible (UV-vis) spectroscopy were used to characterize BHAD and BPUs. Compared with BHAD, BPUs showed hypochromic change in UV-visible spectroscopy. The obtained BPUs have good thermal dye migration. The effect of BHAD content on BPUs’ emulsion stability, water resistance, mechanical properties, and thermal performance were investigated systematically by particle size analysis, water absorption ratio, tensile strength test, and thermogravimetric analysis.     

N,N-双(2-羟乙基)-2-氨基乙磺酸钠为扩链剂的磺酸型聚氨酯水凝胶制备及性能

以异佛尔酮二异氰酸酯(IPDI)、聚乙二醇-2000(PEG)为主要原料,二羟甲基丙酸(DMPA)和N,N-双(2-羟乙基)-2-氨基乙磺酸钠(BES-Na)为亲水性扩链剂,制备了一系列磺酸型聚氨酯水凝胶(WPUHs)。 通过X射线衍射仪、热重分析仪和电子万能测试机对凝胶的结构和性能进行了表征。 结果表明,随着BES-Na质量分数的增加,WPUHs的热稳定性逐渐增加,WPUH7(BES-Na质量分数为3.46%)的压缩强度和压缩模量比WPUH1(BES-Na质量分数为0%)分别提高了2.9倍和3.6倍。 BES-Na的质量分数对WPUHs的溶胀初期过程影响显著,WPUHs的平衡溶胀比从20.6增加至29.3。 WPUHs具有良好的温度和pH敏感性,在10~45 ℃范围内,WPUH7平衡溶胀比从17.6增大至33.8,在pH值为2~10范围内,WPUH7平衡溶胀比从21.7增大至70.6。     

High-temperature resistance and hydrophobic polysiloxane-based polyurethane films with cross-linked structure prepared by the sol-gel process

Polysiloxane-based polyurethane films with cross-linked structure are synthesized by the sol-gel process using isophorone diisocyanate (IPDI), polydimethylsiloxane (PDMS), polycaprolactone (PCL) diol, and 3-aminopropyl triethoxysilane (ATS). After the ATS-terminated polyurethane prepolymer, a cross-linked network structure is formed through the process of dehydration and condensation. The hydrophobicity, thermal properties, surface morphology, and mechanical properties of a series of polysiloxane-based polyurethane films with cross-linked structure are further studied. Dynamic mechanical thermal analysis studies show that the crosslink density of polysiloxane-based polyurethane films with cross-linked structure is improved with the addition of ATS. Polysiloxane-based polyurethane films with cross-linked structure can not only enhance mechanical strength but also improve heat resistance and hydrophobicity. The results show that the maximum decomposition temperature of the polysiloxane-based polyurethane films with cross-linked structure reaches 475 °C, the hydrophobicity increases to 114.2°, and the mechanical strength increases to 16.7 Mpa, which are 18.75%, 7.53%, and 59.04% higher than that of the control group, respectively. This is mainly due to the cross-linked network structure formed by the sol-gel process, which limits the movement of the segment and increases the rigidity of the material. Besides, a dense protective layer is formed on the surface due to cross-linking, which prevents the infiltration of water molecules. Interestingly, with the increase of ATS, the R q value of the surface shows an increasing trend. This is in contrast to the study by Kamal Mohamed Seeni Meera et al. Who shows that the R q value decreases with increasing crosslink density. Also, it can be seen from the results of XPS characterization that Si element of the surface is increased, which is mainly due to the sol-gel phenomenon of ATS occurring on the surface of the material.