Crystallization and melting of isotactic polypropylene crystallized from quiescent melt and stress‐induced localized melt

Temperature dependency of crystalline lamellar thickness during crystallization and subsequent melting in isotactic polypropylene crystallized from both quiescent molten state and stress‐induced localized melt was investigated using small angle X‐ray scattering technique. Both cases yield well‐defined crystallization lines where inverse lamellar thickness is linearly dependent on crystallization temperature with the stretching‐induced crystallization line shifted slightly to smaller thickness direction than the isothermal crystallization one indicating both crystallization processes being mediated a mesomorphic phase. However, crystallites obtained via different routes (quiescent melt or stress‐induced localized melt) show different melting behaviors. The one from isothermal crystallization melted directly without significant changing in lamellar thickness yielding well‐defined melting line whereas stress‐induced crystallites followed a recrystallization line. Such results can be associated with the different extent of stabilization of crystallites obtained through different crystallization routes. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 957–963     

Stratified morphology of a polypropylene/elastomer blend following channel flow

A thermoplastic olefin blend consisting of isotactic polypropylene (PP) and an ethylene‐butene copolymer (EBR) impact modifier (25 wt % EBR) was subjected to a short, high‐shear pulse within the flow channel of a pressure‐driven microextruder following low‐shear channel filling from a reservoir of the melt. The resulting morphology was examined by laser scanning confocal fluorescence microscopy (LSCFM), with contrast provided by a fluorescent tracer in the EBR minor phase. Shear experiments were performed under isothermal conditions with a known wall shear stress for a specified duration, providing a well‐defined thermal and flow history. Low‐shear channel filling produces small droplets across the central region of the channel and large droplets, consistent with steady‐state shear, in the regions near the channel walls. After cooling the molten blend to a crystallization temperature of 153 °C, a brief interval (5 s ～ 1/2000 of the quiescent crystallization time) of high shear (wall shear stress: 0.1 MPa) induces rapid, highly oriented crystallization and a stratified morphology. Ex situ LSCFM reveals a “skin” at the channel walls (～70 μm) in which greatly elongated fiberlike droplets, oriented along the flow direction, are embedded in highly oriented crystalline PP. Further from the walls but directly beside the skin layers are surprising zones in which EBR domains show no deformation or orientation. Several zones of intermediate deformation and orientation at an angle to the flow direction are located closer to the center of the channel. At the center of the channel, EBR droplets are spherical, as expected for channel flow. The various strata are explained by the interplay of droplet deformation, breakup, and coalescence with the shear‐induced crystallization kinetics of the matrix. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2842–2859, 2002     

The influence of thermoelastomers on the crystallization behavior of isotactic polypropylene under shear

The crystallization behaviors of isotactic polypropylene (iPP) and its blends with thermoelastomers have been investigated with in situ X‐ray scattering and optic microscopy. At quiescent condition, the crystallization kinetics of iPP is not affected by the presence of elastomers; while determined by the viscosity, the differences are observed on sheared samples. With a fixed shear strain, the crystallization rate increases with increasing the shear rate. The fraction of oriented lamellar crystals in blends is higher than that in pure iPP sample, while the percentage of β phase is reduced by the presence of the elastomers. On the basis of experimental results, no direct correlation among the fraction of oriented lamellae, the percentage of β phase, and growth rate can be deduced. The evolution of the fraction of oriented lamellae supports that shear field promotes nucleation rather than growth process. Shear flow induces the formation of nuclei not only with preferring orientation but also with random orientation. The total density of nuclei, which determines the crystallization kinetics, does not control the ratio between nuclei with and without preferring orientation, which determines the fraction of oriented lamellae. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1188–1198, 2006     

Isothermal crystallization kinetics and melting behavior of poly(ethylene terephthalate)/barite nanocomposites

Poly(ethylene terephthalate) (PET)/Barite nanocomposites were prepared by direct melt compounding. The effects of PET‐Barite interfacial interaction on the dynamic mechanical properties and crystallization were investigated by DMA and DSC. The results showed that Barite can act as a nucleating agent and the nucleation activity can be increased when the Barite was surface‐modified (SABarite). SABarite nanoparticles induced preferential lamellae orientation because of the strong interfacial interaction between PET chains and SABarite nanoparticles, which was not the case in Barite filled PET as determined by WAXD. For PET/Barite nanocomposites, the Avrami exponent n increased with increasing crystallization temperature. Although at the same crystallization temperature, the n value will decrease with increasing SABarite content, indicating of the enhancement of the nucleation activity. Avrami analyses suggest that the nucleation mechanism is different. The activation energy determined from Arrhenius equation reduced dramatically for PET/SABarite nanocomposite, confirming the strong interfacial interaction between PET chains and SABarite nanoparticles can reduce the crystallization free energy barrier for nucleus formation. In the DSC scan after isothermal crystallization process, double melting behavior was found. And the double endotherms could be attributed to the melting of recrystallized less perfect crystallites or the secondary lamellae produced during different crystallization processes. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 655–668, 2009     

Effects of spacing between the exfoliated clay platelets on the crystallization behavior of polyamide‐6 in polyamide‐6/clay nanocomposites

Exfoliated polyamide‐6 (PA6)/organoclay nanocomposite films with planar‐oriented clay platelets were prepared by the simple hot pressing of melt‐extruded nanocomposite pellets. The average distance between the neighboring clay platelets was controlled by changes in the clay loading content in the nanocomposites. The effects of the clay platelet spacing on the crystallization behavior of PA6 were investigated with transmission electron microscopy and wide‐angle X‐ray diffraction. The crystal lamellae were found to be mainly perpendicular to the clay surface for the nanocomposites with large spacing between the clay sheets at low clay loading contents. This perpendicular orientation morphology was attributed to the strong interactions between the PA6 molecular chain and the clay surface. In contrast, the crystal lamellae were found to be parallel to the clay surface when the spacing between the neighboring clay platelets was less than 30 nm. It was concluded that the confinement crystallization of PA6 within the nanoscale channels formed by clay sheets resulted in this parallel orientation texture. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 284–290, 2006     

On the origin of the “core‐free” morphology in microinjection‐molded HDPE

This study investigates the morphology of a high‐density polyethylene processed with microinjection molding. Previous work pointed out that a “core‐free” morphology exists for a micropart (150‐μm thick), contrasting with the well‐known “skin‐core” morphology of a conventional part (1.5‐mm thick). Local analyses are now conducted in every structural layer of these samples. Transmission electron microscopy observations reveal highly oriented crystalline lamellae perpendicular to the flow direction in the micropart. Image analysis also shows that lamellae are thinner. Wide‐angle X‐ray diffraction measurements using a microfocused beam highlight that highly oriented shish–kebab morphologies are found through the micropart thickness, with corresponding orientation function close to 0.8. For the macropart, quiescent crystallized morphologies are found with few oriented structures. Finally, the morphology within the micropart is more homogeneous, but the crystalline structures created are disturbed due to the combined effects of flow‐induced crystallization and thermal crystallization during processing. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1470–1478, 2011     

Stiffness constants prediction of nanocomposites using a periodic 3D‐FEM model

Predictive models, which enable the prediction of nanocomposite properties from their morphologies and account for polymer orientation, could greatly assist the exploitation of this new class of materials in more diversified and demanding market fields. This article focuses on the prediction of effective elastic properties (Young's moduli) of polymer nanocomposite films (copolyamide‐6/nanoclay) using 3D analytical (based on the Mori‐Tanaka theory) and 3D finite element (FE) models. The analytical model accounts for the orientation of polymer chains induced by drawing. 3D FE model exploits the representative volume element concept and accounts for the nanocomposite morphology as determined from transmission electron microscopy experiments. Model predictions were compared with experimental results obtained for nanocomposite films produced by means a pilot‐scale film blowing equipment and collected at different draw ratios. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Crystallization studies of isotactic polypropylene containing nanostructured polyhedral oligomeric silsesquioxane molecules under quiescent and shear conditions

Crystallization studies at quiescent and shear states in isotactic polypropylene (iPP) containing nanostructured polyhedral oligomeric silsesquioxane (POSS) molecules were performed with in situ small‐angle X‐ray scattering (SAXS) and differential scanning calorimetry (DSC). DSC was used to characterize the quiescent crystallization behavior. It was observed that the addition of POSS molecules increased the crystallization rate of iPP under both isothermal and nonisothermal conditions, which suggests that POSS crystals act as nucleating agents. Furthermore, the crystallization rate was significantly reduced at a POSS concentration of 30 wt %, which suggests a retarded growth mechanism due to the molecular dispersion of POSS in the matrix. In situ SAXS was used to study the behavior of shear‐induced crystallization at temperatures of 140, 145, and 150 °C in samples with POSS concentrations of 10, 20, and 30 wt %. The SAXS patterns showed scattering maxima along the shear direction, which corresponded to a lamellar structure developed perpendicularly to the flow direction. The crystallization half‐time was calculated from the total scattered intensity of the SAXS image. The oriented fraction, defined as the fraction of scattered intensity from the oriented component to the total scattered intensity, was also calculated. The addition of POSS significantly increased the crystallization rate during shear compared with the rate for the neat polymer without POSS. We postulate that although POSS crystals have a limited role in shear‐induced crystallization, molecularly dispersed POSS molecules behave as weak crosslinkers in polymer melts and increase the relaxation time of iPP chains after shear. Therefore, the overall orientation of the polymer chains is improved and a faster crystallization rate is obtained with the addition of POSS. Moreover, higher POSS concentrations resulted in faster crystallization rates during shear. The addition of POSS decreased the average long‐period value of crystallized iPP after shear, which indicates that iPP nuclei are probably initiated in large numbers near molecularly dispersed POSS molecules. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2727–2739, 2001     

Crystallization behavior and thermal property of biodegradable poly(3‐hydroxybutyrate)/multi‐walled carbon nanotubes nanocomposite

Biodegradable poly(3‐hydroxybutyrate) (PHB)/functionalized multi‐walled carbon nanotubes (f‐MWNTs) nanocomposite was prepared in this work by solution casting method at 2 wt% f‐MWNTs loading. Scanning electron microscopy and transmission electron microscopy observations indicate a homogeneous distribution of f‐MWNTs in the PHB matrix. Nonisothermal melt crystallization, overall isothermal melt crystallization kinetics, and crystalline morphology of neat PHB and the PHB/f‐MWNTs nanocomposite were studied in detail. It is found that the presence of f‐MWNTs enhances the crystallization of PHB during nonisothermal and isothermal melt crystallization processes in the nanocomposite due to the heterogeneous nucleation effect of f‐MWNTs. Moreover, the incorporation of a small quantity of f‐MWNTs apparently improves the thermal stability of the PHB/f‐MWNTs nanocomposite with respect to neat PHB. Two methods are employed to study the activation energies of thermal degradation for both the neat PHB and the PHB/f‐MWNTs nanocomposite. The activation energy of thermal degradation of the PHB/f‐MWNTs nanocomposite is higher than that of neat PHB. Copyright © 2009 John Wiley & Sons, Ltd.     

Crystallization behavior of poly(ε‐caprolactone)/multiwalled carbon nanotube composites

Differential scanning calorimetry (DSC), polarized optical microscopy, and X‐ray diffraction methods were used to investigate the isothermal crystallization behavior and crystalline structure of poly(?‐caprolactone) (PCL)/multiwalled carbon nanotube (MWNT) composites. PCL/MWNT composites were prepared via the mixing of a PCL polymer solution with carboxylic groups containing multiwalled carbon nanotubes (c‐MWNTs). Both Raman and Fourier transform infrared spectra indicated that carboxylic acid groups formed at both ends and on the sidewalls of the MWNTs. A transmission electron microscopy micrograph showed that c‐MWNTs were well separated and uniformly distributed in the PCL matrix. DSC isothermal results revealed that introducing c‐MWNTs into the PCL structure caused strongly heterogeneous nucleation induced by a change in the crystal growth process. The activation energy of PCL drastically decreased with the presence of 0.25 wt % c‐MWNT in PCL/c‐MWNT composites and then increased with increasing MWNT content. The result indicated that the addition of c‐MWNT to PCL induced heterogeneous nucleation (lower total activation energy) at a lower c‐MWNT content and then reduced the transportation ability of polymer chains during crystallization processes at a higher MWNT content (higher total activation energy). A correlation between the crystallization kinetics, melting behavior, and crystalline structure of PCL/c‐MWNT composites was also discussed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 598–606, 2006     

Isothermal crystallization kinetics of chain‐extended PET

The crystallization behavior of a commercial chain‐extended PET (foam grade) was evaluated and compared to that of bottle‐grade PET. Cold and melt isothermal crystallization were analyzed by using the Avrami' model. The foam grade PET showed a slower crystallization kinetic compared to the bottle‐grade PET. The Hoffman‐Lauritzen analysis showed that the energetic barriers to nucleation and molecular mobility were higher for the chain‐extended PET. This resulted in a lower nucleation rate in both cold and melt crystallization. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1966–1972, 2005     

Crystallization kinetics of poly(trimethylene terephthalate)

The isothermal crystallization kinetics of poly(trimethylene terephthalate) (PTT) have been investigated using differential scanning calorimetry (DSC) and polarized light microscopy (PLM). Enthalpy data of exotherm from isothermal crystallization were analyzed using the Avrami theory. The average value of the Avrami exponent, n, is about 2.8. From the melt, PTT crystallizes according to a spherulite morphology. The spherulite growth rate and the overall crystallization rate depend on crystallization temperature. The increase in the spherulitic radius was examined by polarized light microscopy. Using values of transport parameters common to many polymers (U* = 1500 cal/mol, T_∞= T_g − 30 °C) together with experimentally determined values of T (248 °C) and T_g (44 °C), the nucleation parameter, k_g, for PTT was determined. On the basis of secondary nucleation analyses, a transition between regimes III and II was found in the vicinity of 194 °C (ΔT ≅ 54 K). The ratio of k_g of these two regimes is 2.1, which is very close to 2.0 as predicted by the Lauritzen–Hoffman theory. The lateral surface‐free energy, σ = 10.89 erg/cm² and the fold surface‐free energy, σ_e = 56.64 erg/cm² were determined. The latter leads to a work of chain‐folding, q = 4.80 kcal/mol folds, which is comparable to PET and PBT previously reported. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 934–941, 2000     

Crystallization kinetics and crystallization behavior of syndiotactic polystyrene/clay nanocomposites

We investigated the effects of montmorillonite (clay) on the crystallization kinetics of syndiotactic polystyrene (sPS) with isothermal differential scanning calorimetry analyses. The clay was dispersed into the sPS matrix via melt blending on a scale of 1–2 nm or up to about 100 nm, depending on the surfactant treatment. For a crystallization temperature of 240 °C, the isothermal crystallization data were fitted well with the Avrami crystallization equation. Crystallization data on the kinetic parameters (i.e., the crystallization rate constant, Avrami exponent, clay content, and clay/surfactant cation‐exchange ratio) were also investigated. Experimental results indicated that the crystallization rate constant of the sPS nanocomposite increased with increasing clay content. The clay played a vital role in facilitating the formation on the thermodynamically more favorable all‐β‐form crystal when the sPS was melt‐crystallized. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2097–2107, 2001     

Isothermal crystallization kinetics of polypropylene latex–based nanocomposites with organo‐modified clay

The effect of organo‐modified clay (Cloisite 93A) on the crystal structure and isothermal crystallization behavior of isotactic polypropylene (iPP) in iPP/clay nanocomposites prepared by latex technology was investigated by wide angle X‐ray diffraction, differential scanning calorimetry and polarized optical microscopy. The X‐ray diffraction results indicated that the higher clay loading promotes the formation of the β‐phase crystallites, as evidenced by the appearance of a new peak corresponding to the (300) reflection of β‐iPP. Analysis of the isothermal crystallization showed that the PP nanocomposite (1% C93A) exhibited higher crystallization rates than the neat PP. The unfilled iPP matrix and nanocomposites clearly shows double melting behavior; the shape of the melting transition progressively changes toward single melting with increasing crystallization temperature. The fold surface free energy (σ_e) of polymer chains in the nanocomposites was lower than that in the PP latex (PPL). It should be reasonable to treat C93A as a good nucleating agent for the crystallization of PPL, which plays a determinant effect on the reduction in σ_e during the isothermal crystallization of the nanocomposites. The activation energy, ΔE_a, decreased with the incorporation of clay nanoparticles into the matrix, which in turn indicates that the nucleation process is facilitated by the presence of clay. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1927–1938, 2010     

Crystallization kinetics in shearing‐induced oriented and stretched poly(ethylene oxide)

Isothermal crystallization kinetics in the melting of poly(ethylene oxide) (PEO) were investigated as a function of the shear rate and crystallization temperature by optical microscopy. The radial growth rates of the spherulites are described by a kinetics equation including shearing and relaxation combined effects and the free energy for the formation of a secondary crystal nucleus. The free‐energy difference between the liquid and crystalline phases increased slightly with rising shearing rates. The experimental findings showed that the influence of the relaxation of PEO, which is related to the shear‐induced orientation and stretch in a PEO melt, on the rate of crystallization predominated over the influence of the shearing. This indicated that the relaxation of PEO should be more important so that the growth rates increase with shearing, but it was nearly independent of the shear rate within the measured experimental range. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 656–665, 2004     

Effect of partial melting on the crystallization kinetics of nylon‐1212

The isothermal and nonisothermal crystallization kinetics of partially melted nylon‐1212 was investigated with differential scanning calorimetry. Because of partial melting, the pre‐existing crystals changed the crystallization mechanism and had a strong effect on the crystallization process. The Avrami exponent and interfacial free energy of the chain‐folded surface of partially melted nylon‐1212 were higher than those of completely melted nylon‐1212. The work of chain folding was determined to be 5.9 kcal/mol. The activation energy of the isothermal crystallization process was determined to be 399.1 kJ/mol, far higher than that of complete melting. The crystallization rate coefficient and Jeziorny analysis indicated that the ability of nonisothermal crystallization for partially melted nylon‐1212 was enhanced. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3222–3230, 2005     

Transient and athermal effects in the crystallization of polymers. II. Nonisothermal crystallization

Nonisothermal crystallization of several polymers was investigated with differential scanning calorimetry and optical microscopy. The results indicated that as in the case of isothermal processes, crystallization starts with nucleation on noncompletely melted crystalline residues. It is assumed that if the crystalline residues are subcritical at melting temperatures, they can become stable by an athermal mechanism during cooling. There is also some contribution of nucleation on heterogeneities. The next mechanism of nucleation is a classical homogeneous process occurring by thermal fluctuations. The results showed the non‐steady‐state character of the nonisothermal crystallization of polymers. In the investigated range of cooling rates, the non‐steady‐state character of nonisothermal crystallization of polymers is dominated by the transient thermal effects. In the range of high temperatures, the transient homogeneous nucleation can be interpreted with the Ziabicki model, and the steady‐state rate determined from nonisothermal experiments coincides with the rate determined in isothermal crystallization. The athermal nucleation occurring at the beginning of crystallization from noncompletely melted aggregates seems to be independent of the applied cooling rate. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 68–79, 2003     

Crystallization and morphology of poly(vinylidene fluoride)/poly(3‐hydroxybutyrate) blends. III. Crystallization and phase diagram by differential scanning calorimetry

The crystallization of poly(vinylidene fluoride) (PVDF)/poly(3‐hydroxybutyrate) (PHB) blends was studied with differential scanning calorimetry, from which the phase diagram was derived. Strong miscibility was underlined by the large negative Flory–Huggins interaction parameter (?0.25). The crystallization of the blend components differed remarkably. Whereas PVDF always crystallized in the surroundings of a homogeneous melt, PHB crystallized in a volume that was confined by the already existing PVDF spherulites, partly in their surroundings and partly inside. Under isothermal conditions, PVDF usually crystallized regularly in three dimensions with predominant quench‐induced athermal nucleation. The Avrami exponent for PVDF dendritic spherulitic growth was, however, distinctly smaller than that for compact growth, and this revealed the two‐dimensional lamellar growth inside. This deviation from ideal Avrami behavior was caused by the development of compositional inhomogeneities as PVDF crystallization proceeded, and this decelerated the kinetics. PHB crystallized three‐dimensionally with mixed thermal and athermal nucleation outside the PVDF spherulites. Inside the PVDF spherulites, PHB crystallization proceeded in a fibrillar fashion with thermal nucleation; the growth front followed the amorphous paths inside the dendritic PVDF spherulites. The crystallization was faster than that in the melt of uncrystallized PVDF. Solid PVDF acts possibly heterogeneously nucleating, accelerating PHB crystallization. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 287–295, 2005     

Crystallization,melting behavior,and morphology of PP/Novolac blends

The crystallization, melting behavior, and morphology of Polypropylene (PP) and PP/Novolac blends were studied by scanning electron microscopy, wide angle X‐ray diffraction, differential scanning calorimetry, and polarized optical microscope. The results showed that the crystallization of PP in PP/Novolac blends was strongly influenced by crystallization temperature, particles size of Novolac, crosslinking, and compatibilizer maleic anhydride‐grafted PP. The Novolac resin could not only affect the crystal structure, but also acted as effective nucleating agents, accelerating the crystallization of PP in the PP/Novolac blends. And the smaller the Novolac particles were, the more effective were the nucleating agent for PP crystallization. Avrami equation was used to analyze the isothermal crystallization kinetics of PP and PP/Novolac blends. The influences of curing and compatibilizer on the crystallization behavior of PP were rather complicated. The crystallization thermodynamics were estimated using the Hoffman theory. The incorporation of cured Novolac and compatibilizer evidently decreased the chain folding energy of PP. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3288–3303, 2006     

Crystallization, morphology, and dynamic mechanical properties of poly(trimethylene terephthalate)/clay nanocomposites

The poly(trimethylene terephthalate) (PTT)/clay nanocomposite has been successfully prepared via melt intercalation using a co-rotating twin screw extruder. The nanocomposite was characterized by wide angle X-ray diffraction (WAXD), transmission electron microscope (TEM), differential scanning calorimetry (DSC), polarized light microscope (PLM) and dynamic mechanical analysis (DMA). The nanocomposite forms an exfoliated structure, which can be observed by WAXD and TEM. The effect of clay layers on the crystallization behaviors of PTT was studied through isothermal and non-isothermal crystallization methods. The results suggest that the introduction of nanosize clay layers accelerates the crystallization rate of PTT and the clay layers act as nucleation agents. The morphology of spherulites was investigated with PLM and the result is well in agreement with crystallization kinetics. DMA shows that glass transition temperature (T_g) and storage modulus (E^′) of the PTT matrix of the nanocomposite are higher than those of pure PTT.