Effects of electron beam irradiation on the photoelectrochemical properties of TiO2 film for DSSCs

TiO₂ has been widely utilized for various industrial applications such as photochemical cells, photocatalysts, and electrochromic devices. The crystallinity and morphology of TiO₂ films play a significant role in determining the overall efficiency of dye-sensitized solar cells (DSSCs). In this study, the preparation of nanostructured TiO₂ films by electron beam irradiation and their characterization were investigated for the application of DSSCs. TiO₂ films were exposed to 20–100 kGy of electron beam irradiation using 1.14 MeV energy acceleration with a 7.46 mA beam current and 10 kGy/pass dose rates. These samples were characterized using X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), and X-ray photoelectron spectroscopy (XPS) analysis. After irradiation, each TiO₂ film was tested as a DSSC. At low doses of electron beam irradiation (20 kGy), the energy conversion efficiency of the film was approximately 4.0% under illumination of simulated sunlight with AM 1.5 G (100 mW/cm²). We found that electron beam irradiation resulted in surface modification of the TiO₂ films, which could explain the observed increase in the conversion efficiency in irradiated versus non-irradiated films.     

TiO2@CdS core–shell nanorods films: Fabrication and dramatically enhanced photoelectrochemical properties

In this paper, we prepared TiO₂@CdS core–shell nanorods films electrodes using a simple and low-cost chemical bath deposition method. The core–shell nanorods films electrodes were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and UV–vis spectrometry techniques. After applying these TiO₂@CdS core–shell nanorods electrodes in photovoltaic cells, we found that the photocurrent was dramatically enhanced, comparing with those of bare TiO₂ nanorods and CdS films electrodes. Moreover, TiO₂@CdS core–shell nanorods film electrode showed better cell performance than CdS nanoparticles deposited TiO₂ nanoparticles (P25) film electrode. A photocurrent of 1.31 mA/cm², a fill factor of 0.43, an open circuit photovoltage of 0.44 V, and a conversion efficiency of 0.8% were obtained under an illumination of 32 mW/cm², when the CdS nanoparticles deposited on TiO₂ nanorods film for about 20 min. The maximum quantum efficiency of 5.0% was obtained at an incident wavelength of 500 nm. We believe that TiO₂@CdS core–shell heterostructured nanorods are excellent candidates for studying some fundamental aspects on charge separation and transfer in the fields of photovoltaic cells and photocatalysis.     

Influence of surfactant and annealing temperature on optical properties of sol–gel derived nano-crystalline TiO2 thin films

Titanium dioxide thin films have been synthesized by sol–gel spin coating technique on glass and silicon substrates with and without surfactant polyethylene glycol (PEG). XRD and SEM results confirm the presence of nano-crystalline (anatase) phase at an annealing temperature of 300 °C. The influence of surfactant and annealing temperature on optical properties of TiO₂ thin films has been studied. Optical constants and film thickness were estimated by Swanepoel's (envelope) method and by ellipsometric measurements in the visible spectral range. The optical transmittance and reflectance were found to decrease with an increase in PEG percentage. Refractive index of the films decreased and film thickness increased with the increase in percentage of surfactant. The refractive index of the un-doped TiO₂ films was estimated at different annealing temperatures and it has increased with the increasing annealing temperature. The optical band gap of pure TiO₂ films was estimated by Tauc's method at different annealing temperature.     

Mesoporous TiO2−xAy (A = N,S) as a visible-light-response photocatalyst

Mesoporous TiO_2?xA_y (A = N, S) thin films were fabricated using thiourea as a doping resource by a combination of sol-gel and evaporation-induced self-assembly (EISA) processes. The results showed that thiourea could serve two functions of co-doping nitrogen and sulfur and changing the mesoporous structure of TiO₂ thin films. The resultant mesoporous TiO_2?xA_y (A = N, S) exhibited anatase framework with a high porosity and a narrow pore distribution. The formation of the O–Ti–N and O–Ti–S bonds in the mesoporous TiO_2?xA_y (A = N, S) were substantiated by the XPS spectra. A new bandgap in visible light region (520 nm) corresponding to 2.38 eV could be formed by the co-doping. After being illuminated for 3 h, methyl orange could be degraded nearly completely by the co-doped sample under both ultraviolet irradiation and visible light illumination. While pure mesoporous TiO₂ could only degrade 60% methyl orange under UV illumination and showed negligible photodegradation capability in the visible light range. Furthermore, the photo-induced hydrophilic activity of TiO₂ film was improved by the co-doping. The mesoporous microstructure and high visible light absorption could be attributed to their good photocatalytic acitivity and hydrophilicity.     

Preparation and photocatalytic activity of Cu-deposited TiO2 film with high transparency

Cu-deposited TiO₂ films were prepared by photoreduction of Cu(II) in the presence of sodium formate. With the initial Cu(II) concentrations more than 100 mg L^?1, induction periods were observed before the transmittance decreased. Scanning electron microscopy indicated that Cu particles of 2.6 ± 0.5 μm were deposited isolatedly with much open space in the induction periods. The films prepared by changing the irradiation time within the induction periods showed a higher photocatalytic activity than a pure TiO₂ for the degradation of methylene blue under the reaction condition without purging air.     

Synthesis and properties of polyfluorene copolymers bearing thiophene and porphyrin

To search for more wider absorption and higher charge carriers mobilities materials of polymer solar cell, a series of soluble alternating polyfluorene copolymers were synthesized by palladium-catalyzed Suzuki coupling reaction. Their structures were determined by 1H NMR, IR and UV-vis. And their UV-vis absorption spectra indicated that they had strong absorption over 600 nm spectral range and nearly cover 400-700 nm visible region. The band gaps of copolymers calculated according to cyclic voltammetry （CV） were between 1.96 and 2.03 eV. Polymer：TiO2 bulk-heterojunction films were made from mixtures of polymer and titanium isopropoxide, a precursor for TiO2, via hydrolysis in air overnight. The photoluminescence at 380-800 nm of the blend film of PT-TPP20 （5 mg/mL）：Ti（OC3H7）4 （80 μL/mL） （20% volume fraction） was significantly quenched in the 50% Ti（OC3H7）4 blend film, indicating that rapid and efficient separation of photoinduced electron-hole pairs.     

Scanning electrochemical microscopy investigation of the rate of formation of a passivating TiO2 layer on a Ti G4 dental implant

Titanium and alloys with titanium as the major component are widely used for making biomedical implants, such as artificial dental roots. In our laboratory, we have studied the kinetics of the self-healing reaction of the TiO₂ film that forms on the surface of such an implant. Amperometric SECM approach curves were recorded over the surface of a grade 4 titanium (Ti G4) dental implant sample at specific times after the metal surface had been exposed to an air-saturated buffer solution. A ferrocene methanol redox mediator and a platinum microelectrode tip (r = 12.5 μm) were used in the experiments. The effective rate coefficient (k_eff) values for the mediator regenerating surface reaction were estimated using Wittstock's method from the approach curves recorded at different time points. Decreasing values of k_eff over time indicated an increasing rate of formation of the passivating TiO₂ film.     

Crystallization of the anodic oxide on titanium in sulphuric acids solution at a very low potential

Anodic oxide films were formed on the deposited pure titanium in 0.1 M H₂SO₄ solution at 30 °C by using cyclic voltammetry (CV) anodization technique. Clear atomic images and step-terrace structure were observed on it by using STM, which gave a direct evidence for the local crystallinity of the anodic oxide films, even though the maximum anodization potential (E_max) was −50 mV, which was much lower than the lowest potential for crystallization in literatures. Moreover, the crystalline degree of the whole anodic oxide film was estimated from the refractive index (n), and the results showed that the crystalline degree increased with potentials. The analysis of XPS spectra revealed that high potentials were also beneficial for the formation of TiO₂, which was the primary substance for the formation of stable crystals in the oxide films.     

Electrochemically synthesized CdS nanoparticle-modified TiO2 nanotube-array photoelectrodes: Preparation,characterization, and application to photoelectrochemical cells

A novel electrodeposited CdS nanoparticle-modified highly-ordered TiO₂ nanotube-array photoelectrode and its application to photoelectrochemical cells is reported. Results show formation of a thin, nanoparticulate CdS layer, comprised of sphere-like 10–20 nm diameter nanoparticles, on the anodic synthesized TiO₂ nanotube-array (inner diameter of 70 nm, wall thickness 25 nm and ca. 400 nm length) electrode. The resulting CdS–TiO₂ photoelectrode has an as-fabricated bandgap of 2.53, and 2.41 eV bandgap after sintering at 350 °C in N₂ ambient. Photoelectrochemical properties are described in detail.     

Facile synthesis of thick ordered mesoporous TiO2 film for dye-sensitized solar cell use

Crack-free thick ordered mesoporous TiO₂ films with excellent optical quality have been synthesized by combination of “Doctor Blade” technique and a two-step evaporation induced self-assembly (EISA) method. By employing the as-synthesized mesoporous film with the thickness of 7 μm as the photoanode in dye-sensitized solar cell (DSC), a solar conversion efficiency of 6.53% has been obtained at 30 mW cm⁻² light intensity.     

Synthesis and studies on photochromic properties of vanadium doped TiO2 nanoparticles

Pure and (0.5–3 at%) vanadium doped TiO₂ nanoparticles have been synthesized by wet chemical method. The as synthesized materials have been characterized by using XRD, atomic force microscope (AFM), Raman, EPR and UV–vis spectroscopy techniques. From XRD studies, both pure as well as vanadium doped TiO₂ have been found to show pure anatase phase. The value of lattice constant c is smaller in doped TiO₂ as compared to undoped and has been found to decrease with increase in vanadium concentration. AFM studies show formation of spherical particles with particle size ～23 nm in all the samples. Photochromic behavior of these materials has been studied by making their films in alkyd resin. Vanadium doped TiO₂ films show reversible change in color from beige-yellow to brownish violet on exposure to UV light. The mechanism of coloration and bleaching process has been discussed.     

Fast formation of thick and transparent titania nanotubular films from sputtered Ti

Ti films sputtered on transparent fluorine-doped tin oxide glass substrates were anodized in fluoride-containing organic electrolyte in the presence of H₂O. In this work, anodic TiO₂ nanotubes (ATNs) as long as 9.2 ± 0.3 μm were obtained with high growth rate of 0.64 ± 0.3 μm min^?1. We demonstrated the optimum anodization conditions for ATN growth on foreign substrates, were within the range of 0.3–0.5% (wt) NH₄F, with 3–5% (vol) H₂O at 60 V. XPS and ICP-MS were utilized to elucidate the increase of thickness and volume expansion obtained from the sputtered Ti film to their ATN forms. The ATN films exhibited excellent uniformity and adhesion to the substrates.     

Modification of photocatalytic TiO2 thin films by electron beam irradiation

Noble metal-modified TiO₂ films were prepared by electron beam deposition of Pt, Pd, Au and Ag on the surface of TiO₂ films with diameters ranging from <1 nm to 500 nm. The morphology of the films was characterized by X-ray diffractometry (XRD), field emission scanning electron microscope (FMSEM) and transmission electron microscope (TEM). The photocatalytic capability of the films were tested and compared by degradation of methyl orange (MO) in aqueous solutions under both UV and visible light illumination.     

Oscillations of pH at the Fe│H2SO4 interface during anodic dissolution

An unmodified Pt microelectrode and a Pt microelectrode coated with polyaniline were used in conjunction with a scanning electrochemical microscope (SECM) to study anodic dissolution in the Fe│H₂SO₄ system. The concentrations of Fe^2 + (c_Fe2 +) measured with the unmodified microelectrode and the pH values measured with the polyaniline-modified microelectrode were recorded in situ during current oscillations in the Fe│H₂SO₄ system and were found to change periodically at the Fe│H₂SO₄ interface. The changes in c_Fe2 + may be caused by the periodic formation and dissolution of surface film(s), which could be salt films and/or oxide films. If a salt film is formed, it is unlikely to affect the pH. Since the pH changes periodically during the current oscillations, it can be deduced that the surface film is mainly composed of oxide, and that the formation and dissolution of the oxide film play a key role in the current oscillations of the system.     

Synthesis of titanium dioxide nanocrystalline layers using hexaprismatic shaped μ-oxo Ti(IV) alkoxo carboxylates as precursors

The reaction between Ti(OR)₄ (R = ⁿBu, ⁱBu, SiMe₃) and 2,2-dimethylpropionic acid lead to the formation of hexanuclear μ-oxo titanium(IV) alkoxo carboxylato complexes of the general formula [Ti₆O₆(OR)₆(OOC^tBu)₆]. Thermal decomposition pathways of these compounds and their potential application in the preparation of TiO₂ nanolayers using chemical vapor deposition (CVD) methods have been discussed. The type of the alkoxide ligands causes differences in the thermolysis pathway, and the type of the volatile decomposition products. Among the examined complexes only [Ti₆O₆(OR)₆(OOC^tBu)₆] (R = ⁱBu, SiMe₃) show promising properties for their application as precursors in CVD methods. The TiO₂ films were grown in a wide range of substrate temperatures (653–873 °K), under the total reactor pressure 2.0–3.0 mbar. The crystallinity and the composition of layers were analyzed by X-ray diffraction (XRD). It was found that the formation of TiO₂ amorphous, anatase or rutile films depends on the deposition temperature and gas phase composition.     

Facile preparation of large aspect ratio ellipsoidal anatase TiO2 nanoparticles and their application to dye-sensitized solar cell

A simple one-step heat-treatment of peroxotitanate complex aqueous solution at around 100 °C was resulted in the formation of ellipsoidal anatase TiO₂ nanoparticles having a high aspect ratio with no branches. The length of these ellipsoidal TiO₂ falls in the range of 200–350 nm, depending on mole ratio of Ti⁴⁺/H₂O₂. Dye-sensitized solar cell based on these ellipsoidal nanocrystalline TiO₂ as photoanode was fabricated and characterized.     

Rapid anodic growth of TiO2 and WO3 nanotubes in fluoride free electrolytes

In the present work we report on the formation of bundles of high aspect ratio TiO₂ nanotubes and WO₃ nanopores structures with very thin tube or pore walls using anodization under “high voltage” conditions in perchlorate or chloride containing electrolytes. The bundles of TiO₂ nanotubes consist of separated tubes with diameters in the range of approximately 20–40 nm and the WO₃ nanopores consist of pores with diameters in the range of 30–50 nm. Growth occurs locally at specific surface locations. Both the TiO₂ and the WO₃ structures can be grown up to several dozens of micrometers in length within few minutes. We suggest that the growth of these high aspect structures is initiated by localized anodic breakdown event, triggered by a sufficiently high applied anodic field.     

Optical,structural and electrochromic studies of molybdenum oxide thin films with nanorod structure

The MoO₃ thin films were prepared via sol–gel dip coating method on glass and FTO glass substrate. The optical and other properties of multilayered MoO₃ films with 2–10 layers were investigated. The MoO₃ films were studied using UV–Visible transmission, XRD, SEM, FTIR and Cyclic Voltammetry (CV) measurements. The band gap value for MoO₃ films was evaluated and in the range of 3.2 eV–3.72 eV. The XRD spectrum reveals that the crystallinity increases along the (020) and (040) planes with the increase in thickness. The SEM images showed the formation of nanorods upto six layers. The FTIR spectrum confirms the formation of MoO₃. The 6 layered films show the maximum anodic (spike)/cathodic (peak) diffusion coefficient of 18.84/1.701 × 10^?11 cm²/s. The same film exhibits the change in optical transmission of 49% with the bleached/coloured state transmission of 62/13%.     

Enhancement in as-grown CuInSe2 film microstructure by a three potential pulsed electrodeposition method

P-type copper indium diselenide (CuInSe₂) films have been prepared onto ITO substrates by an electrodeposition method, that sequentially applies potential pulses at the deposition potential of each element Cu, Se and In, and then step it back in cyclically to induce the solid state reaction between the elements. Two electrolyte concentrations as well as three different pulse durations were assessed. The resulting films were compared with those deposited at fixed electrode potentials. As-grown films are nanocrystalline and have an E_g ～ 0.95 eV. Raman spectroscopy shows that Se and Cu–Se contents decrease while pulse duration increases and electrolyte concentration decreases. Cu–Se phases are even absent for films grown at the low electrolyte concentration. These results represent a great improvement in the film phase purity reducing the need of post-deposition treatments.     

Photoinduced hydrophilic and photocatalytic response of hydrothermally grown TiO2 nanostructured thin films

It is demonstrated that nanostructured titanium (IV) oxide (TiO₂) films can be deposited on glass substrates at 95 °C using hydrothermal growth, their properties being greatly affected by the substrate materials. Anatase TiO₂ films grown on ITO for deposition period of 50 h were observed to exhibit a very efficient, reversible light-induced transition to super-hydrophilicity, reaching a nearly zero contact angle. Enhanced photocatalytic activity (65%) was found for the rutile TiO₂ samples grown on microscope glass, possibly due to their higher roughness with respect to anatase grown on ITO. The effect of the substrate material used is discussed in terms of the TiO₂ phase and morphology control, for the best photoinduced hydrophilic and photocatalytic performance of the samples.