The performance of coupled (CdS:CdSe) quantum dot-sensitized TiO2 nanofibrous solar cells

Highly porous networks and reduced grain boundaries with one-dimensional (1-D) nanofibrous morphology offer enhanced charge transport in solar cells applications. Quantum dot (QDs) decorated TiO₂ nanofibrous electrodes, unlike organic dye sensitizers, can yield multiple carrier generations due to the quantum confinement effect. This paper describes the first attempt to combine these two novel approaches, in which CdS (～18 nm) and CdSe (～8 nm) QDs are sensitized onto electrospun TiO₂ nanofibrous (diameter ～80–100 nm) electrodes. The photovoltaic performances of single (CdS and CdSe) and coupled (CdS/CdSe) QDs-sensitized TiO₂ fibrous electrodes are demonstrated in sandwich-type solar cells using polysulfide electrolyte. The observed difficulties in charge injection and lesser spectral coverage of single QDs-sensitizers are solved by coupling (CdS:CdSe) two QDs-sensitizers, resulting in a enhanced open-circuit voltage (0.64 V) with 2.69% efficiency. These results suggest the versatility of fibrous electrodes in QDs-sensitized solar cell applications.     

TiO2@CdS core–shell nanorods films: Fabrication and dramatically enhanced photoelectrochemical properties

In this paper, we prepared TiO₂@CdS core–shell nanorods films electrodes using a simple and low-cost chemical bath deposition method. The core–shell nanorods films electrodes were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and UV–vis spectrometry techniques. After applying these TiO₂@CdS core–shell nanorods electrodes in photovoltaic cells, we found that the photocurrent was dramatically enhanced, comparing with those of bare TiO₂ nanorods and CdS films electrodes. Moreover, TiO₂@CdS core–shell nanorods film electrode showed better cell performance than CdS nanoparticles deposited TiO₂ nanoparticles (P25) film electrode. A photocurrent of 1.31 mA/cm², a fill factor of 0.43, an open circuit photovoltage of 0.44 V, and a conversion efficiency of 0.8% were obtained under an illumination of 32 mW/cm², when the CdS nanoparticles deposited on TiO₂ nanorods film for about 20 min. The maximum quantum efficiency of 5.0% was obtained at an incident wavelength of 500 nm. We believe that TiO₂@CdS core–shell heterostructured nanorods are excellent candidates for studying some fundamental aspects on charge separation and transfer in the fields of photovoltaic cells and photocatalysis.     

Highly efficient CdSe quantum-dot-sensitized TiO2 photoelectrodes for solar cell applications

With 4.2 nm quantum-dots (QDs) as seeds on TiO₂ film, a highly efficient TiO₂ photoelectrode was prepared by a seed-growing process using chemical bath deposition technique, followed by a covering process with ZnS layer, and a post-sintering process at 400 °C. The assembled solar cells presented IPCE peak values of 73% and power conversion efficiency of 3.21% under AM 1.5 G irradiation.     

Visible LED light photoelectrochemical sensor for detection of L-Dopa based on oxygen reduction on TiO2 sensitized with iron phthalocyanine

The present work describes the development of a new strategy to photoelectrochemical detection of L-Dopa at low potential based on oxygen reduction on TiO₂ sensitized with iron phthalocyanine (FePc/TiO₂). The FePc/TiO₂ composite shows a photocurrent 10-fold higher than that of pure TiO₂ nanoparticles and it was 4-fold higher than that of FePc exploiting visible light. The band gaps of pure TiO₂ nanoparticles, FePc and FePc/TiO₂, calculated according to the Kubelka–Munk equation, were 3.22 eV, 3.11 eV and 2.82 eV, respectively. The FePc/TiO₂ composite showed a low charge transfer resistance in comparison to the photoelectrode modified with FePc or TiO₂. Under optimized conditions, the photoelectrochemical sensor shows a linear response range from 20 up to 190 μmol L^− 1 with a sensitivity of 31.8 μA L mmol^− 1 and limit of detection of 1.5 μmol L^− 1 for the detection of L-Dopa.     

Photocatalytic activity of TiO2 nanotube layers loaded with Ag and Au nanoparticles

Ag and Au nanoparticles were found to significantly enhance the photocatalytic activity of self-organized TiO₂ nanotubular structures. The catalyst systems are demonstrated to be highly efficient for the UV-light induced photocatalytic decomposition of a model organic pollutant – Acid Orange 7. The metallic nanoparticles with a diameter of ∼10 ± 2 nm (Ag) and ∼28 ± 3 nm (Au) were attached to a nanotubular TiO₂ layer that consists of individual tubes of ∼100 nm of diameter, ∼2 μm in length and approx. 15 nm of wall thickness. Both metal particle catalyst systems enhance the photocatalytic decomposition significantly more on the nanotubes support than placed on a compact TiO₂ surface.     

Layer-by-layer nanoparticle coatings on lignocellulose wood microfibers

The layer-by-layer (LbL) self-assembly technique was applied to deposit organized multilayers of TiO₂ or SiO₂ nanoparticles of 30–80 nm diameter, and 50-nm diameter halloysite clay nanotubes on softwood fibers. Fluorescent and scanning electron microscopy images showed complete nanoparticle coating on these fibers. The thickness of the two-layer coating was estimated as 46, 58, and 115 nm for TiO₂, SiO₂, and halloysite tubules, respectively, which corresponds to ca. 1 wt% nanoparticle loading of the fibers. The brightness test of paper handsheets prepared from nanocoated fibers showed that TiO₂ nanoparticle coating gave handsheet reflectance of 84% at 450 nm, which is 4% higher than the brightness of the control sample from virgin fibers. The paper handsheets prepared with nanoparticle-coated fibers had 30–50% higher porosity with tensile strength index retained close to the control sample.     

AgSbS2 semiconductor-sensitized solar cells

We present a ternary semiconductor nanoparticle sensitizer – AgSbS₂ – for solar cells. AgSbS₂ nanoparticles were grown using a two-stage successive ionic layer adsorption and reaction process. First, Ag₂S nanoparticles were grown on the surface of a nanoporous TiO₂ electrode. Secondly, a Sb–S film was coated on top of the Ag₂S. The double-layered structure was transformed into AgSbS₂ nanoparticles ~ 40 nm in diameter, after post-deposition heating at 350 °C. The AgSbS₂-sensitized TiO₂ electrodes were fabricated into liquid-junction solar cells. The best cell yielded a power conversion efficiency of 0.34% at 1 sun and 0.42% at 0.1 sun. The external quantum efficiency (EQE) spectrum covered the range of 380–680 nm with a maximal EQE of 10.5% at λ = 470 nm. The method can be applied to grow other systems of ternary semiconductor nanoparticles for solar absorbers.     

Formation of porous TiOx biomaterials in H3PO4 electrolytes

In this work, formation of porous TiO_x layers and theirs corrosion behavior were studied. Application of H₃PO₄ electrolytes results in porous TiO_x formation. The process is enhanced by small amount of HF content in the electrolyte. The HF results in higher current density, enhancing dissolution. Small 0.5% HF concentration results in nanopores formation, with pore diameter of about 45 nm. Increase of HF concentration up to 10% results in pores with average diameter of about 5.2 μm. An increase of etching time results in larger pore diameter, but between large 2–5 μm diameter pores smallest ones were observed with diameter below 200 nm. In the initial etching process a remnants of the flat surface are presents with initial cracks in the surface, indicating places for growth of the pores.The TiO_x layers can be used as a biomaterial. The corrosion behavior of the layer investigated in Ringer’s solution, revealed an excellent corrosion resistance, with respect to pure Ti.     

Chemical bath deposition of CdS quantum dots on vertically aligned ZnO nanorods for quantum dots-sensitized solar cells

Formation of CdS quantum dots (Q dots) on the vertically aligned ZnO nanorods electrode was carried out by chemical bath deposition. The diameter and thickness of ZnO nanorods are ～100–150 nm and ～1.6 μm, respectively, and CdS Q dots on ZnO nanorods have a diameter of smaller than 15 nm. In application of the Q dots-sensitized solar cells, composite film exhibited a power conversion efficiency of 0.54% under air mass 1.5 condition (80 mW/cm²), and incident-photon-to-current conversion efficiency showed 18.6%.     

CdS/TiO2–SrTiO3 heterostructure nanotube arrays for improved solar energy conversion efficiency

TiO₂–SrTiO₃ heterostructure nanotube arrays have been utilized as a novel oxide substrate for CdS quantum dot sensitized solar cells (QDSCs). SrTiO₃ on TiO₂ surface passivates surface states of TiO₂ and builds cascade-structured band alignment, which significantly reduces charge recombination at electrode surface. CdS/TiO₂–SrTiO₃ electrode exhibits a superior photoelectrochemical performance than CdS/TiO₂ electrode with ～ 70% increase in external quantum efficiency. This study suggests that the suppression of charge recombination at electrode surface is critical to efficient solar energy conversion.     

Doping level effect on visible-light irradiation W-doped TiO2–anatase photocatalysts for Congo red photodegradation

A series of W-modified TiO₂ (W–TiO₂) photocatalysts were synthesized by a simple sol–gel method. The new photocatalysts were characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV–vis-diffuse reflectance spectroscopy (DRS), and Brunauer, Emmett and Teller (BET) surface area analyzer. The photoactivity of the W–TiO₂ photocatalysts was evaluated by the photocatalytic oxidation of Congo red (CR) dye. It was found that the average size of the prepared photocatalysts is 10 nm. Moreover, they have high surface areas (∼ 216 m² g⁻¹) and their light-absorption extends to the visible region compared to pure TiO₂. The effects of W-loading and of the calcination temperature of the prepared photocatalysts on their photocatalytic activity were also studied. The obtained results show that the W_0.5–TiO₂ photocatalyst calcined at 350 °C is much highly photoactive than non-doped or highly doped TiO₂. The enhanced photocatalytic activity of the weakly doped TiO₂ may be attributed to the increase in the charge separation efficiency and the presence of surface acidity on the W_0.5–TiO₂ photocatalyst.     

Mesoporous TiO2−xAy (A = N,S) as a visible-light-response photocatalyst

Mesoporous TiO_2?xA_y (A = N, S) thin films were fabricated using thiourea as a doping resource by a combination of sol-gel and evaporation-induced self-assembly (EISA) processes. The results showed that thiourea could serve two functions of co-doping nitrogen and sulfur and changing the mesoporous structure of TiO₂ thin films. The resultant mesoporous TiO_2?xA_y (A = N, S) exhibited anatase framework with a high porosity and a narrow pore distribution. The formation of the O–Ti–N and O–Ti–S bonds in the mesoporous TiO_2?xA_y (A = N, S) were substantiated by the XPS spectra. A new bandgap in visible light region (520 nm) corresponding to 2.38 eV could be formed by the co-doping. After being illuminated for 3 h, methyl orange could be degraded nearly completely by the co-doped sample under both ultraviolet irradiation and visible light illumination. While pure mesoporous TiO₂ could only degrade 60% methyl orange under UV illumination and showed negligible photodegradation capability in the visible light range. Furthermore, the photo-induced hydrophilic activity of TiO₂ film was improved by the co-doping. The mesoporous microstructure and high visible light absorption could be attributed to their good photocatalytic acitivity and hydrophilicity.     

Electrochemical properties of liquid electrolyte added quasi-solid state TiO2 dye-sensitized solar cells

In this study a process has been introduced to replace traditional liquid or solid electrolyte coatings on dye-sensitized photoelectrode in solar cells. This process has more efficient diffusion of electrolyte, hence higher sensitivity. Better interfacial contact between polymer electrolyte and TiO₂ photoelectrode had improved electrochemical response and ionic conductivity of cell. Conductivity of this electrode was 9.33 × 10⁻³ S cm⁻¹ (at room temperature), which is much higher than the using traditional process for addition of electrolytes. It has 0.68 V open-circuit voltage and 3.19 mA cm⁻² short-circuit current density. Energy conversion efficiency of this cell was about 37% higher than the cell developed with traditional processes under constant light intensity (45 mW cm⁻²).     

Demetallation of methemoglobin in cellulose nanofibril–TiO2 nanoparticle composite membrane electrodes

Porous composite films containing cellulose nanofibrils (from sisal) and TiO₂ nanoparticles (ca. 6 nm diameter) are obtained in a layer-by-layer assembly process. Each layer consists of ca. 0.18 μg cellulose nanofibrils and ca. 0.72 μg TiO₂ (determined by QCMB) and adds a thickness of ca. 16 nm (by AFM) to the uniform deposit. The TiO₂ nanophase is creating conducting pathways for electrons in a relatively open cellulose structure (ca. 82% open pores) potentially suitable for the immobilization of large redox proteins such as methemoglobin.Methemoglobin is shown to readily adsorb into the cellulose–TiO₂ film. However, electrochemical responses for the immobilized methemoglobin in aqueous 0.1 M phosphate buffer at pH 5.5 suggest that facile demetallation occurs. Experiments with Fe³⁺ in the absence of protein result in voltammetric responses indistinguishable from those observed for immobilized methemoglobin. In the presence of ethylenediamine tetraacetic acid (EDTA) the voltammetric signals for the Fe³⁺ immediately disappear. Complementary experiments conducted in 0.1 M acetate buffer at pH 5.5 demonstrate that methemoglobin can indeed be immobilized in electrochemically active form and without demetallation loss of the voltammetric signal in the presence of EDTA. Demetallation appears to occur (i) in the presence of phosphate, (ii) at pH 5.5, (iii) and in the presence of a charged surface.     

Spectroscopic properties of RBiBO4 (R = Ca,Sr) glasses doped with TiO2

Transparent glasses, melt quenching derived, containing 10RO·20Bi₂O₃·(70 ? x)B₂O₃·xTiO₂ [R = Ca, Sr] with x = 0, 0.5, 1.0 wt% were characterized by X-ray powder diffraction. Physical and spectroscopic properties viz., density, absorption, emission, electron paramagnetic resonance (EPR) and FTIR were investigated. The absorption band around 823 nm in pure glass samples is attributed to the electronic transition of ³P₀ to ³P₂ of Bi⁺ radicals. A small absorption hump centered around 609 nm is found in all doped glasses due to ²T_2g to ²E_g transition of octahedral Ti³⁺ ions. The emission results revealed that all the samples exhibit a broad emission band covering entire visible-light range, with λ_ex = 360 nm, centered 470–520 nm corresponds to electronic transition of ³P₁ to ¹S₀ of Bi³⁺ ions, therefore the present materials can be potentially used as tunable or full-color display systems. And a strong emission around 706 nm with λ_ex = 514 nm due to transition of ²P_3/2 to ²P_1/2 of Bi²⁺ ions. In SrO mixed glasses Ti⁴⁺ ions effect the environment of Bi³⁺ ion symmetry units from C₂ to C_3i. A small EPR signal (at room temperature) is observed in titanium doped glasses due to Ti³⁺ ions. In both the series with increase of TiO₂ concentration BO₄ units are gradually converted into BO₃ units and new cross linkages are formed, like B–O–Ti, Bi–O–Ti at the expense of B–O–B bonds.     

Synthesis of hybrid solar cells using CdS nanowire array grown on conductive glass substrates

High-density CdS nanowire (NW) arrays were successfully grown on fluorine-doped tin oxide (FTO)-coated glass substrates by vapor–liquid–solid (VLS) mechanism at a remarkably reduced temperature of ～450 °C. Bi catalyst layer and polyvinyl alcohol (PVA) played a major role in the low-temperature synthesis of high-quality CdS NW arrays. CdS NWs were defect free single crystalline Wurtzite crystals and they were 50–100 nm and 2–5 μm in diameter and length, respectively. CdS NWs were combined with poly[2-methoxy-5-(2′-ethylhexyloxy)-1,4-phenylenevinylene] (MEH-PPV), a conjugated polymer to form organic–inorganic hybrid structures. The UV–visible light absorption and emission behavior of MEH-PPV/CdS hybrids was investigated and their potential to be used as photovoltaic cells was demonstrated.     

Small diameter TiO2 nanotubes with enhanced photoresponsivity

We report ultraviolet (UV) light detection of thin wall TiO₂ nanotubes (TNTs) with open diameter ~ 20 nm obtained by a two anodization procedure. This small diameter nanotubular geometry shows significant enhancement of the photoresponsivity and results in a large increase of photocurrent. The photocurrent is one order higher than that of classical nanotubes with diameter of 140 nm at − 1.0 V bias. We attribute this improvement to the modulation of hole carrier density as a result of field effects from the diameter-dependent population of the surface-trapped electrons. This finding demonstrates inherent size effects of internal gain in semiconductor nanotubes.     

Influence of particle size on the photoactivity of Ti/TiO2 thin film electrodes,and enhanced photoelectrocatalytic degradation of indigo carmine dye

Photoanodes based on Ti/TiO₂ thin films were prepared by the sol–gel method, using either tetraisopropoxide (Ti(OPri)₄) or modified tetraisopropoxide, producing electrodes with different sized nanoparticle coatings, termed nanoporous (20 nm) or nanoparticulated (10 nm) electrodes. The anatase form dominated the composition of the nanoparticulated electrode, which presented a higher surface area, a flat band potential shift of ?160 mV and a 50% improvement in photoactivity, compared to the nanoporous electrode. 100% color removal, and 75% mineralization, of indigo carmine dye were achieved after 15 min of photoelectrocatalytic treatment using a nanoparticulated Ti/TiO₂ electrode operated at a current density of 0.4 mA cm^?2. Our findings indicate that the use of nanoparticulated electrodes, under UV irradiation and with controlled current density, is an efficient alternative for the removal of food dye contaminants during wastewater treatment.     

Photocatalytic activity of nitrogen and copper doped TiO2 nanoparticles prepared by microwave-assisted sol-gel process

Cu and N-doped TiO₂ photocatalysts were synthesized from titanium (IV) isopropoxide via a microwave-assisted sol-gel method. The synthesized materials were characterized by X-ray diffraction, UV-vis diffuse reflectance, photoluminescence (PL) spectroscopy, SEM, TEM, FT-IR, Raman spectroscopy, photocurrent measurement technique, and nitrogen adsorption–desorption isotherms. Raman spectra and XRD showed an anatase phase structure. The SEM and TEM images revealed the formation of an almost spheroid mono disperse TiO₂ with particle sizes in the range of 9-17 nm. Analysis of N₂ isotherm measurements showed that all investigated TiO₂ samples have mesoporous structures with high surface areas. The optical absorption edge for the doped TiO₂ was significantly shifted to the visible light region. The photocurrent and photocatalytic activity of pure and doped TiO₂ were evaluated with the degradation of methyl orange (MO) and methylene blue (MB) solution under both UV and visible light illumination. The doped TiO₂ nanoparticles exhibit higher catalytic activity under each of visible light and UV irradiation in contrast to pure TiO₂. The photocatalytic activity and photocurrent ability of TiO₂ have been enhanced by doping of the titania in the following order: (Cu, N) - codoped TiO₂ > N-doped TiO₂ > Cu-doped TiO₂ > TiO₂. COD result for (Cu, N)-codoped TiO₂ reveals ∼92% mineralization of the MO dye on six h of visible light irradiation.     

Ag2S quantum dot-sensitized solar cells

We present a new photosensitizer – Ag₂S quantum dots (QDs) – for solar cells. The QDs were grown by the successive ionic layer adsorption and reaction deposition method. The assembled Ag₂S-QD solar cells yield a best power conversion efficiency of 1.70% and a short-circuit current of 1.54 mA/cm² under 10.8% sun. The solar cells have a maximal external quantum efficiency (EQE) of 50% at λ = 530 nm and an average EQE of ～ 42% over the spectral range of 400–1000 nm. The effective photovoltaic range covers the visible and near-infrared spectral regions and is ～ 2–4 times broader than that of the cadmium chalcogenide systems — CdS and CdSe. The results show that Ag₂S QDs can be used as a highly efficient and broadband sensitizer for solar cells.