Biobased polyurethanes from polyether polyols obtained by ionic‐coordinative polymerization of epoxidized methyl oleate

A series of poly(ether urethane) networks were synthesized from polyether polyols obtained by ionic‐coordinative polymerization of epoxidized methyl oleate (EMO) using 4,4′‐methylenebis(phenyl isocyanate) or l ‐lysine diisocyanate as coupling agents. Moreover, a variety of segmented poly(ether urethane) networks with different hard segment contents were obtained using 1,3‐propanediol as the chain extender. The materials were characterized by differential scanning calorimetry, thermogravimetric analysis, dynamic mechanical thermal analysis, and tensile properties. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Radical and cationic polymerizations of 3‐ethyl‐3‐methacryloyloxymethyloxetane

3‐Ethyl‐3‐methacryloyloxymethyloxetane (EMO) was easily polymerized by dimethyl 2,2′‐azobisisobutyrate (MAIB) as the radical initiator through the opening of the vinyl group. The initial polymerization rate (R_p) at 50 °C in benzene was given by R_p = k[MAIB]^0.55 [EMO]^1.2. The overall activation energy of the polymerization was estimated to be 87 kJ/mol. The number‐average molecular weight (M?_n) of the resulting poly(EMO)s was in the range of 1–3.3 × 10⁵. The polymerization system was found to involve electron spin resonance (ESR) observable propagating poly(EMO) radicals under practical polymerization conditions. ESR‐determined rate constants of propagation (k_p) and termination (k_t) at 60 °C are 120 and 2.41 × 10⁵ L/mol s, respectively—much lower than those of the usual methacrylate esters such as methyl methacrylate and glycidyl methacrylate. The radical copolymerization of EMO (M₁) with styrene (M₂) at 60 °C gave the following copolymerization parameters: r₁ = 0.53, r₂ = 0.43, Q₁ = 0.87, and e₁ = +0.42. EMO was also observed to be polymerized by BF₃OEt₂ as the cationic initiator through the opening of the oxetane ring. The M?_n of the resulting polymer was in the range of 650–3100. The cationic polymerization of radically formed poly(EMO) provided a crosslinked polymer showing distinguishably different thermal behaviors from those of the radical and cationic poly(EMO)s. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1269–1279, 2001     

Preparation of high cis‐1,4 polyisoprene with narrow molecular weight distribution via coordinative chain transfer polymerization

High cis‐1,4 polyisoprene with narrow molecular weight distribution has been prepared via coordinative chain transfer polymerization (CCTP) using a homogeneous rare earth catalyst composed of neodymium versatate (Nd(vers)₃), dimethyldichlorosilane (Me₂SiCl₂), and diisobutylaluminum hydride (Al(i‐Bu)₂H) which has strong chain transfer affinity is used as both cocatalyst and chain transfer agent (CTA). Differentiating from the typical chain shuttling polymerization where dual‐catalysts/CSA system has been used, one catalyst/CTA system is used in this work, and the growing chain swapping between the identical active sites leads to the formation of high cis‐1,4 polyisoprene with narrowly distributed molecular weight. Sequential polymerization proves that irreversible chain termination reactions are negligible. Much smaller molecular weight of polymer obtained than that of stoichiometrically calculated illuminates that, differentiating from the typical living polymerization, several polymer chains can be produced by one neodymium atom. The effectiveness of Al(i‐Bu)₂H as a CTA is further testified by much broad molecular weight distribution of polymer when triisobutylaluminum (Al(i‐Bu)₃), a much weaker chain transfer agent, is used as cocatalyst instead of Al(i‐Bu)₂H. Finally, CCTP polymerization mechanism is validated by continuously decreased M_w/M_n value of polymer when increasing concentration of Al(i‐Bu)₂H extra added in the Nd(ver)₃/Me₂SiCl₂/Al(i‐Bu)₃ catalyst system. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Cationic polymerization of n‐hexyloxyallene by using halogen‐bonding organocatalysts

The cationic polymerization of n‐hexyloxyallene was investigated by using halogen‐bonding organocatalysts ( Cat A – Cat D ). Although the neutral catalyst Cat C showed a poor polymerization activity, iodine‐carrying bidentate cationic catalyst Cat A brought about the smooth polymerization giving rise to a polymer with M_n of 2710 under [ Cat A ]:[IBVE‐HCl]:[monomer] = 10:10:500 in mM concentrations. Judging from the color change of polymerization system and electrospray ionization mass spectra of recovered catalyst, the decomposition of organocatalyst was suggested. When α‐bromodiphenylmethane was used as an initiator, the relatively controlled polymerization proceeded at the low monomer conversion likely due to the weak halogen‐bonding interaction of Cat A with the bromide anion. On the other hand, bromine‐carrying bidentate catalyst Cat D gave low‐molecular‐weight polymers (M_n < 1550) to be less suitable for polymerization. From the ¹H‐NMR spectrum, it was found that the 1,2‐polymerization unit and 2,3‐polymerization unit are included in 75:25. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2436–2441     

Controlled ring‐opening polymerization of propylene oxide catalyzed by double metal‐cyanide complex

A double metal‐cyanide catalyst based on Zn₃[Co(CN)₆]₂ was prepared. This catalyst is very effective for the ring‐opening polymerization of propylene oxide. Polyether polyols of moderate molecular weight having low unsaturation (<0.015 meq/g) can be prepared under mild conditions. The molecular weight of polymer is entirely controlled by a reacted monomer‐to‐initiator ratio. The polymers prepared with stepwise addition of monomer exhibit a narrower molecular weight distribution as compared with those prepared with one‐step addition of monomer. Various compounds containing active hydrogen, except basic compounds and low‐carbon carboxylic acid, may be used as initiators. The reaction rate increases with increasing catalyst amount and decreases with rising initiator concentration. Polymerization involves a rapid exchange reaction between the active species and the dormant species. It was also proven that, to a certain extent, the chain termination of this catalytic system is reversible or temporary. ¹³C NMR analysis showed that the polymer has a random distribution of the configurational sequences and head‐to‐tail regiosequence. It is assumed that the polymerization proceeds via a cationic coordination mechanism. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1142–1150, 2002     

Determination of the Chemical Structure of Poly-β (-)-pinene by NMR Spectroscopy

This paper is dedicated to the memory of our friend and colleague Annalaura Segre.

The chemical structure of a series of β (-)-pinene polymers (PBP) obtained by radiation-induced polymerization, free radical initiation, cationic polymerization over a Friedel-Craft catalyst and by coordinative polymerization over a Ziegler-Natta catalyst has been fully elucidated by ¹H and ¹³C-NMR spectroscopy. 2D NMR techniques have been applied in order to assign all the NMR resonances to the structures of the PBP investigated. The NMR spectra show that the most regular PBP structure is obtained by radiation-induced polymerization followed by the free radical initiated polymerization. The most defective structure has been observed in the case of PBP prepared by cationic mechanism over a Friedel-Crafts catalyst. The discussion accounts for different types of defects and cross-links present in the PBPs investigated whose fundamental structure is based on the p-menthene repeating unit.

NMR self-diffusion measurements have been performed to evaluate the molecular weight of all the PBP investigated. The highest molecular weight (2600 Dalton) was found in the case of PBP prepared by Ziegler-Natta catalyst, while the lowest molecular weight was found in the case of PBP prepared by radiation-induced polymerization (about 1000 Dalton).     

Synthesis and characterization of a series of 2‐aminopyridine nickel(II) complexes and their catalytic properties toward ethylene polymerization

A series of 2‐aminopyridine Ni(II) complexes bearing different substituent groups {(2‐PyCH₂NAr)NiBr, Ar = 2,4,6‐trimethylphenyl ( 3a) , 2,6‐dichlorophenyl ( 3b ), 2,6‐dimethylphenyl ( 3c) , 2,6‐diisopropylphenyl ( 3d ), 2,6‐difluorophenyl ( 3e ); (2‐PyCH₂NHAr)₂NiBr₂, Ar = 2,6‐diisopropylphenyl ( 4a )} have been synthesized and investigated as precatalysts for ethylene polymerization in the presence of methylaluminoxane (MAO). High molecular weight branched polymers as well as short‐chain oligomers were simultaneously produced with these complexes. Enhancing the steric bulk of the ortho‐aryl‐substituents of the catalyst resulted in higher ratio of solid polymer to oligomer and higher molecular weight of the polymer. With ortho‐haloid‐substitution, the catalysts afforded a product with low polymer/oligomer ratio ( 3b ) and even only oligomers ( 3e ) in which C₁₄H₂₈ had the maximum content. Compared with complex 3d containing ionic ligand, complex 4a containing neutral ligand exhibited obviously low catalytic activity for ethylene polymerization. The molecular weight, molecular weight distribution, and microstructure of the resulted polymer were characterized by gel permeation chromatography and ¹³C NMR spectrogram. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1618–1628, 2008     

s‐Triazine‐based hyperbranched polyethers: Synthesis,characterization, and properties

A series of s‐triazine‐based hyperbranched polyethers (HBPE) have been synthesized to obtain thermostability but flexible polymers by an interfacial polycondensation of different diols as A₂ and cyanuric chloride as B₃ monomers using A₂ + B₃ approach in the presence of a phase transfer catalyst. The polymerization reaction parameters are optimized, and the results indicate that the optimum conditions for the interfacial polycondensation are a 2:3 mole ratio of cyanuric chloride to diol using butanediol, benzyldimethylhexadecyl ammonium chloride as the catalyst, dichloromethane as the organic solvent, and a three‐step procedure with keeping the reaction mixture at different low temperatures for 2h/2h/5h. Other techniques such as high‐temperature solution, one‐step polycondensation, and transesterification were also carried out to synthesize the HBPE but proved to be not suitable due to large number of side reactions. The synthesized polymers were characterized by FTIR, ¹H NMR, and ¹³C NMR spectroscopy, hydroxyl number determination, solution viscosity measurements, and GPC analysis. The thermal behavior of the hyperbranched polymer was investigated by thermogravimetric analysis and differential scanning calorimetry. All the results were compared with those from an analogous linear polyether, obtained from 2‐methoxy‐4,6‐dichloro‐s‐triazine and butanediol by using the same polymerization technique. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3994–4004, 2010     

Mechanistic discussion of cationic crosslinking copolymerizations of 1,2‐epoxycyclohexane with diepoxide crosslinkers accompanied by intramolecular and intermolecular chain transfer reactions

Our previous mechanistic discussion of the free‐radical crosslinking monoallyl/diallyl copolymerizations was extended to the cationic crosslinking monoepoxide/diepoxide copolymerizations, typically including 1,2‐epoxycyclohexane (ECH) as a monoepoxide and bis[3,4‐epoxycyclohexylmethyl] adipate (BECHMA) as a diepoxide crosslinker. In the cationic polymerization, oligomer is usually obtained because of the occurrence of characteristic chain‐forming reactions. Therefore, cationic crosslinking monoepoxide/diepoxide copolymerizations could be in the category of the network formation through free‐radical crosslinking monoallyl/diallyl copolymerizations. Thus, the gelation behavior was discussed by comparing the actual gel points with the theoretical ones; the greatly delayed gelation from theory was observed. Then, the resulting network polymer precursors (NPPs) were characterized by SEC‐MALLS‐viscometry to clarify the cationic crosslinking ECH/BECHMA copolymerization mechanism. Notably, the correlation lines of molecular weight versus elution volume were specific for the NPPs obtained at a high conversion close to the gel point as compared with those obtained by the free‐radical crosslinking monoallyl/diallyl copolymerization. This may be ascribed to the occurrence of intramolecular and intermolecular chain transfer reactions characteristic of cationic polymerization; the chain transfer reactions involve the intramolecular and intermolecular nucleophilic attack of ether oxygen or terminal hydroxyl oxygen in the NPPs to a terminal growing cation that leads to the formation of not only the loop‐ but also the crosslink‐structures containing NPPs, providing fragile ultrahigh‐molecular‐weight NPP in the SEC columns. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Reverse atom transfer radical polymerization of methyl methacrylate in room‐temperature ionic liquids

The reverse atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) was successfully carried out in 1‐butyl‐3‐methylimidazolium hexafluorophosphate with 2,2′‐azobisisobutyronitrile/CuCl₂/bipyridine as the initiating system, which had been reported as not able to promote a controlled process of MMA in bulk. The living nature of the polymerization was confirmed by kinetic studies, end‐group analysis, chain extension, and block copolymerization results. The polydispersity of the polymer obtained was quite narrow, with a weight‐average molecular weight/number‐average molecular weight ratio of less than 1.2. In comparison with other reverse ATRPs in bulk or conventional solvents, a much smaller amount of the catalyst was used. After a relatively easy removal of the polymer and residue monomer, the ionic liquid and catalytic system could be reused without further treatment. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 143–151, 2003     

Chemistry of olefin polymerization reactions with chromium‐based catalysts

Detailed GC analysis of oligomers formed in ethylene homopolymerization reactions, ethylene/1‐hexene copolymerization reactions, and homo‐oligomerization reactions of 1‐hexene and 1‐octene in the presence of a chromium oxide and an organochromium catalyst is carried out. A combination of these data with the analysis of ¹³C NMR and IR spectra of the respective high molecular weight polymerization products indicates that the standard olefin polymerization mechanism, according to which the starting chain end of each polymer molecule is saturated and the terminal chain end is a C?C bond (in the absence of hydrogen in the polymerization reactions), is also applicable to olefin polymerization reactions with both types of chromium‐based catalysts. The mechanism of active center formation and polymerization is proposed for the reactions. Two additional features of the polymerization reactions, co‐trimerization of olefins over chromium oxide catalysts and formation of methyl branches in polyethylene chains in the presence of organochromium catalysts, also find confirmation in the GC analysis. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5330–5347, 2008     

High Molecular Weight Polystyrene Obtained by Cationic Emulsion Polymerization Catalyzed by Imidazolium‐Based Ionic Liquid

The ionic liquid 1‐n‐butyl‐3‐methylimidazolium heptachlorodiferrate (BMI.Fe₂Cl₇) is efficiently used as catalyst in the cationic emulsion polymerization of styrene. The effect of different reaction temperatures, surfactant, and ionic liquid concentrations on polymer properties as molecular weight distribution and particle size is evaluated. High weight average molecular weights, above 1000 kDa, are achieved at 70% of conversion in 100 nm polystyrene particles formed mainly by micellar nucleation. Particle sizes and molecular weights increase with the decrease of the amount of surfactant. Even at low concentrations, BMI.Fe₂Cl₇/styrene molar ratio equal to 1/1000, the ionic liquid proves to be efficient for the emulsion polymerization of styrene, and lower ionic liquid concentrations lead to the formation of longer polymer chains.     

Hybrid atom transfer radical polymerization system for balanced polymerization rate and polymer molecular weight control

A hybrid polymerization system that combines the fast reaction kinetics of conventional free radical polymerization and the control of molecular weight and distribution afforded by ATRP has been developed. High‐free radical initiator concentrations in the range of 0.1–0.2 M were used in combination with a low concentration of ATRP catalyst. Conversions higher than 90% were achieved with ATRP catalyst concentrations of less than 20 ppm within 2 h for the hybrid ATRP system as compared with ATRPs where achieving such conversions would take up to 24 h. These reaction conditions lead to living polymerizations where polymer molecular weight increases linearly with monomer conversion. As in living polymerization and despite the fast rates and low ATRP catalyst concentrations, the polydispersity of the produced polymer remained below 1.30. Chain extension experiments from a synthesized macroinitiator were successful, which demonstrate the living characteristics of the hybrid ATRP process. Catalyst concentrations as low as 16 ppm were found to effectively mediate the growth of over 100 polymer chains per catalytic center, whereas at the same time negating the need for post polymerization purification given the low‐catalyst concentration. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2294–2301, 2010     

Cationic polymerization of L,L‐lactide

Cationic bulk polymerization of L ,L‐ lactide (LA) initiated by trifluromethanesulfonic acid [triflic acid (TfA)] has been studied. At temperatures 120–160 °C, polymerization proceeded to high conversion (>90% within ～8 h) giving polymers with M_n ～ 2 × 10⁴ and relatively high dispersity. Thermogravimetric analysis of resulting polylactide (PLA) indicated that its thermal stability was considerably higher than the thermal stability of linear PLA of comparable molecular weight obtained with ROH/Sn(Oct)₂ initiating system. Also hydrolytic stability of cationically prepared PLA was significantly higher than hydrolytic stability of linear PLA. Because thermal or hydrolytic degradation of PLA starting from end‐groups is considerably faster than random chain scission, both thermal and hydrolytic stability depend on molecular weight of the polymer. High thermal and hydrolytic stability, in spite of moderate molecular weight of cationically prepared PLA, indicate that the fraction of end‐groups is considerably lower than in linear PLA of comparable molecular weight. According to proposed mechanism of cationic LA polymerization growing macromolecules are fitted with terminal ? OH and ? C(O)OSO₂CF₃ end‐groups. The presence of those groups allows efficient end‐to‐end cyclization. Cyclic nature of resulting PLA explains its higher thermal and hydrolytic stability as compared with linear PLA. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2650–2658, 2010     

Metallocene‐mediated cationic ring‐opening polymerization of 2‐methyl‐ and 2‐phenyl‐oxazoline

The cationic ring‐opening polymerization of 2‐methyl‐2‐oxazoline and 2‐phenyl‐2‐oxazoline was efficiently used using bis(η⁵‐cyclopentadienyl)dimethyl zirconium, Cp₂ZrMe₂, or bis(η⁵‐tert‐butyl‐cyclopentadienyl)dimethyl hafnium in combination with either tris(pentafluorophenyl)borate or tetrakis(pentafluorophenyl)borate dimethylanilinum salt as initiation systems. The evolution of polymer yield, molecular weight, and molecular weight distribution with time was examined. In addition, the influence of the initiation system and the monomer on the control of the polymerization was studied. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 000: 000–000, 2011     

Copper(0)‐mediated living radical polymerization of acrylonitrile: SET‐LRP or AGET‐ATRP

Cu(0)‐mediated living radical polymerization was first extended to acrylonitrile (AN) to synthesize polyacrylonitrile with a high molecular weight and a low polydispersity index. This was achieved by using Cu(0)/hexamethylated tris(2‐aminoethyl)amine (Me₆‐TREN) as the catalyst, 2‐bromopropionitrile as the initiator, and dimethyl sulfoxide (DMSO) as the solvent. The reaction was performed under mild reaction conditions at ambient temperature and thus biradical termination reaction was low. The rapid and extensive disproportionation of Cu(I)Br/Me₆‐TREN in DMSO/AN supports a mechanism consistent with a single electron transfer‐living radical polymerization (SET‐LRP) rather than activators generated by electron transfer atom transfer radical polymerization (AGET ATRP). ¹H NMR analysis and chain extension experiment confirm the high chain‐end functionality of the resultant polymer. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Block and star block copolymers by mechanism transformation. II. Synthesis of poly(DOP‐b‐St) by combination of ATRP and CROP

Styrene underwent the ATRP process using an asymmetric difunctional initiator, 2‐hydroxylethyl 2′‐bromobutyrate in combination with CuBr and 2,2′‐bipyridine (bpy). Polystyrene with hydroxyl and bromine groups at each end of the polymer (HO‐PSt‐Br) was obtained, and used as a chain‐transfer agent in the cationic ring‐opening polymerization of 1,3‐dioxepane with triflic acid as initiator. The structures of the polymerization products were analyzed by ¹H NMR and GPC analyses, indicating the formation of block copolymer. The molecular weight distribution of the block copolymer was relatively narrow and the molecular weight of the polyDOP block was high. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 436–443, 2000     

Synthesis and properties of high‐molecular‐weight stereo di‐block polylactides with nonequivalent D/L ratios

Di‐stereoblock polylactides (di‐sb‐PLA: PLLA‐b‐PDLA) having high molecular weight (M_n > 100 kDa) were successfully synthesized by two‐step ring‐opening polymerization (ROP) of L ‐ and D ‐lactides using tin(2‐ethylhexanoate) as a catalyst. By optimizing the polymerization conditions, the block sequences were well regulated at non‐equivalent feed ratios of PLLA and PDLA. This synthetic method consisted of three stages: (1) polymerization of either L ‐ or D ‐lactide to obtain a PLLA or PDLA prepolymer with a molecular weight less than 50 kDa, (2) purification of the obtained prepolymer to remove residual lactide, and (3) polymerization of the enantiomeric lactide in the presence of the purified prepolymer. Their ¹³C and ³¹P NMR spectra of the resultant di‐sb‐PLAs strongly supported their di‐stereo block structure. These di‐sb‐PLAs, having weight‐average molecular weights higher than 150 kDa, were fabricated into polymer films by solution casting and showed exclusive stereocomplexation. The thermomechanical analysis of the films revealed that their heat deformation temperature was limited probably because of their low crystallinity owing to the non‐equivalent PLLA/PDLA ratio. The blend systems of the di‐sb‐PLAs having complementary stereo‐sequences (the one with a long PLLA block and the other with long PDLA block) were also prepared and characterized to enhance the sc crystallinity. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 794–801, 2010     

Solid polymer electrolytes. IV. Preparation and characterization of novel crosslinked epoxy‐siloxane polymer complexes as polymer electrolytes

Two series of novel crosslinked siloxane‐based polymers and their complexes with lithium perchlorate (LiClO₄) were prepared and characterized by Fourier transform infrared spectroscopy, solid‐state NMR (¹³C, ²⁹Si, and ⁷Li nuclei), and differential scanning calorimetry. Their thermal stability and ionic conductivity of these complexes were also investigated by thermogravimetric and AC impedance measurements. In these polymer networks, poly(propylene oxide) chains with different molecular weights were introduced through self‐synthesized epoxy‐siloxane precursors cured with two curing agents. The glass‐transition temperature (T_g) of these copolymers is dependent on the length of the ether units. The dissolution of LiClO₄ considerably increases the T_g of the polyether segments. The dependence of the ionic conductivity was investigated as a function of temperature, LiClO₄ concentration, and the molecular weight of the polyether segments. The ion‐transport behavior was affected by the combination of the ionic mobility and number of carrier ions. The ⁷Li solid‐state NMR line shapes of these polymer complexes suggest a significant interaction between Li⁺ ions and the polymer matrix, and temperature‐ and LiClO₄ concentration‐dependent chemical shifts are correlated with ionic conductivity. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1226–1235, 2002     

Nuclear magnetic resonance monitoring of chain‐end functionality in the atom transfer radical polymerization of styrene

The evolution of the bromine end functionality during the bulk atom transfer radical polymerization (ATRP) of styrene [in the presence of the catalyst CuBr/4,4′‐di‐(5‐nonyl)‐2,2′‐bipyridine] was monitored with 600‐MHz ¹H NMR. A decrease in the functionality versus the conversion was observed. The loss of functionality was especially significant at very high conversions (>90%). The experimental data were compared with a kinetic model of styrene ATRP. The latter indicated that the loss of chain‐end functionality was partly due to bimolecular terminations but was mainly due to β‐H elimination reactions induced by the copper(II) deactivator. These elimination reactions, which occurred later in the reaction, did not significantly affect the polymer molecular weights and the polydispersity. Therefore, a linear evolution of the molecular weights and low‐polydispersity polymers were still observed, despite a loss of functionality. Understanding these side reactions helped in the selection of the proper conditions for reducing the contribution of the elimination process and for preparing well‐defined polystyrene (number‐average molecular weight ～10,000 g mol^?1; weight‐average molecular weight/number‐average molecular weight ～1.1) with a high functionality (92%). © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 897–910, 2005