Ethynylene‐containing donor–acceptor alternating conjugated polymers: Synthesis and photovoltaic properties

Four ethynylene‐containing donor‐acceptor alternating conjugated polymers P1 – P4 with 2,5‐bis(dodecyloxy) substituted phenylene or carbazole as the donor unit and benzothiadiazole (BTZ) as the acceptor unit were synthesized and used as donor polymers in bulk heterojunction polymer solar cells. The optical, electrochemical, and photovoltaic properties of these four polymers with the ethylene unit located at different positions of the polymer chains were systematically investigated. Our results demonstrated that absorption spectra and the HOMO and LUMO energy levels of polymers could be tuned by varying the position of the ethynylene unit in the polymer chains. Photovoltaic devices based on polymer/PC₇₁BM blend films spin coated from chloroform and dichlorobenzene solutions were investigated. For all four polymers, open circuit voltages (V_oc) higher than 0.8 V were obtained. P4 , with ethynylene unit between BTZ and thiophene, shows the best performance among these four polymers, with a V_oc of 0.94 V, a J_sc of 4.2 mA/cm², an FF of 0.40, and a PCE of 1.6%. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Reduced‐bandgap triphenylamine‐alt‐benzo[1,2‐b:4,5‐b′]dithiophene copolymers pending benzothiadiazole or diketopyrrolopyrrole units for efficient polymer solar cells

Two new side‐chain donor–acceptor (D‐A)‐based triphenylamine‐alt‐benzo[1,2‐b:4,5‐b′]dithiophene (TPA‐alt‐BDT) copolymers ( P1 and P2 ) with pendant benzothiadiazole (BT)/diketopyrrolopyrrole (DPP) in TPA unit were synthesized by Stille coupling polymerization. Their thermal, photophysical, electrochemical, blend film morphology and photovoltaic properties were investigated. Efficient bulk heterojunction polymer solar cells (PSCs) were obtained by solution process using both copolymers as donor materials and PC₇₁BM as acceptor. The maximum power conversion efficiency (PCE) of 3.17% with a highest open‐circuit voltage (V_oc) of 0.86V was observed in the P1 ‐based PSCs, while the maximum short‐circuit current (J_sc) of 10.77 mA cm^?2 was exhibited in the P2 ‐based PSCs under the illumination of AM 1.5, 100 mW cm^?2. The alternating binary donor units and pending acceptor groups played a significant role in tuning photovoltaic properties for this class of the side‐chain D–A‐based copolymers. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4103–4110     

Conjugated polymers based on dicarboxylic imide‐substituted isothianaphthene and their applications in solar cells

Four new polymers containing a benzo[c]thiophene‐N‐dodecyl‐4,5‐dicarboxylic imide (DIITN) unit including the homopolymer and three donor–acceptor copolymers were designed, synthesized, and characterized. For these copolymers, DIITN unit with low bandgap was selected as an electron acceptor, whereas 5,5′‐(2,7‐bisthiophen‐2‐yl)‐9‐(2‐decyltetradecyl)‐9H‐carbazole), 5,5′‐(3,3′‐di‐n‐octylsilylene‐2,2′‐bithiophene), and 5,5′‐(2,7‐bisthiophen‐2‐yl‐9,9‐bisoctyl‐9H‐fluoren‐7‐yl) were chosen as the electron donor units to tune the highest occupied molecular orbital/lowest unoccupied molecular orbital (HOMO/LUMO) levels of the copolymers for better light harvesting. These polymers exhibit extended absorption in the visible and near‐infrared range and are soluble in common organic solvents. The relative low lying HOMO of these polymers promises good air stability and high open‐circuit voltage (V_oc) for photovoltaic application. Bulk heterojunction solar cells were fabricated by blending the copolymers with [6,6]‐phenyl‐C61‐butyric acid methyl ester or [6,6]‐phenyl‐C71‐butyric acid methyl ester (PC71BM). The best power conversion efficiency of 1.6% was achieved under simulated sunlight AM 1.5G (100 mW/cm²) from solar cells containing 20 wt % of the fluorene copolymer poly[5,5′‐(2,7‐bisthiophen‐2‐yl‐9,9‐bisoctyl‐9H‐fluoren‐7‐yl)‐alt‐2,9‐(benzo[c]thiophene‐N‐dodecyl‐4,5‐dicarboxylic imide)] and 80 wt % of PC71BM with a high open‐circuit voltage (V_oc) of 0.84 V. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Exploring the influence of acceptor content on semi‐random conjugated polymers

A family of diketopyrrolopyrrole (DPP)‐incorporated P3HT based semi‐random copolymers was synthesized and their optical, electronic and photovoltaic properties were investigated. For the first time, the influence of acceptor content on semi‐random copolymers was explored in the broad range of 10–40% acceptor. A mixture of DPP acceptor units with different side chains (ethylhexyl and decyltetradecyl) was incorporated into each copolymer to improve solubility and film quality. Increased DPP content in the polymer backbone resulted in broadened absorption between 350 and 900 nm, resulting in a monotonic decrease in optical band gap (E_g) of the polymers from 1.49 to 1.37 eV. Highest occupied molecular orbital (HOMO) energy levels showed an increase from 10% DPP to 20–30% DPP, while decreasing for 40% DPP. V_oc values followed a consistent trend with HOMO energy levels. Semi‐random copolymers showed significantly improved photovoltaic properties compared with P3HT. Bulk heterojunction solar cells fabricated from the semi‐random copolymers blended with PC₆₁BM exhibited high short‐circuit current densities (J_sc) up to 10.29 mA/cm² and efficiencies up to 4.43%. A new method of methanol treatment was developed and applied to the semi‐random copolymers resulting in high fill factors approaching 0.70 under ambient conditions. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3884–3892     

Development of naphthalene and quinoxaline‐based donor–acceptor conjugated copolymers for delivering high open‐circuit voltage in photovoltaic devices

Two new quinoxaline‐based polymers, poly[1,5‐didecyloxynaphthalene‐alt‐5,5′‐(5,8‐dithiophen‐2‐yl)‐2,3‐bis(4‐octyloxyphenyl)quinoxaline (PNQx‐p) and poly[1,5‐didecyloxynaphthalene‐alt‐5,5′‐(5,8‐dithiophen‐2‐yl)‐2,3‐bis(3‐octyloxyphenyl)quinoxaline (PNQx‐m), were synthesized by Suzuki coupling reaction and characterized. Thermogravimetric analysis revealed that these polymers are thermally stable with degradation temperature up to 320 °C. As evident from the electrochemical and optical studies, the copolymers have comparable optical band gap (～2 eV) and nearly similar deep highest occupied molecular orbital (HOMO) energy levels of ?5.59 (PNQx‐p) and ?5.61 eV (PNQx‐p). The resulting copolymers possessed relatively low HOMO energy levels promising good air stability and high open circuit voltage (V_oc) for photovoltaic applications. The optimized photovoltaic device with a structure of ITO/PEDOT:PSS/PNQx‐m:PC₇₁BM (1:2, w/w)/LiF/Al shows a power conversion efficiency up to 2.29% with a short circuit current density of 5.61 mA/cm², an V_oc of 0.93 V and a fill factor of 43.73% under an illumination of AM 1.5, 100 mW/cm². The efficiency of the PNQx‐m polymer improved from 2.29 to 2.95% using 1,8‐diiodoocane as an additive (0.25%). © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

New selenophene‐based low‐band gap conjugated polymers for organic photovoltaics

Low‐band gap selenophene‐based polymers were synthesized. Their optoelectronic and photovoltaic properties and space‐charge limited currents were compared with those of the related thiophene‐based polymers. The band gaps of the Se‐based derivatives were approximately 0.05–0.12 eV lower than those of their thiophene counterparts. Organic photovoltaic (OPV) devices based on the blends of these polymers and 1‐(3‐methoxycarbonyl)propyl‐1‐phenyl‐[6,6]‐C₇₁ (PC₇₁BM) were fabricated, and the maximum power conversion efficiency of the OPV device based on PSPSBT and PC₇₁BM was 3.1%—with a short‐circuit current density (J_sc) of 9.3 mA cm^?2, an open‐circuit voltage (V_oc) of 0.79 V, and a fill factor of 0.42—under AM 1.5 G illumination (100 mW cm^?2). © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4550–4557     

Synthesis and photovoltaic properties of two‐dimensional D‐A copolymers with conjugated side chains

Four novel two‐dimensional (2D) donor–acceptor (D‐A) type copolymers with different conjugated side chains, P1 , P2 , P3 , and P4 (see Fig. 1 ), are designed and synthesized for the application as donor materials in polymer solar cells (PSCs). To the best of our knowledge, there were few reports to systematically study such 2D polymers with D‐A type main chains in this area. The optical energy band gaps are about 2.0 eV for P1 – P3 and 1.67 eV for P4 . PSC devices using P1 – P4 as donor and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester as acceptor in a weight ratio of 1:3 were fabricated and characterized to investigate the photovoltaic properties of the polymers. Under AM 1.5 G, 100 mA/cm² illumination, a high open‐circuit voltage (V_oc) of 0.9 V was recorded for P3 ‐based device due to its low HOMO level, and moderate fill factor was obtained with the best value of 58.6% for P4 ‐based device, which may mainly be the result of the high hole mobility of the polymers (up to 1.82 × 10^?3 cm²/V s). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Dithienocyclopentathieno[3,2‐b]thiophene Hexacyclic Arene for Solution‐Processed Organic Field‐Effect Transistors and Photovoltaic Applications

We have developed a ladder‐type dithienocyclopentathieno[3,2‐b]thiophene ( DTCTT ) hexacyclic unit in which the central thieno[3,2‐b]thiophene ring was covalently fastened to two adjacent thiophene rings through carbon bridges, thereby forming two connected cyclopentadithiophene ( CPDT ) units in a hexacyclic coplanar structure. This stannylated Sn‐DTCTT building block was copolymerized with three electron‐deficient acceptors, dibromo‐thieno[3,4‐c]pyrrole‐4,6‐dione ( TPD ), dibromo‐benzothiadiazole ( BT ), and dibromo‐phenanthrenequinoxaline ( PQX ), by Stille polymerization, thereby furnishing a new class of alternating donor–acceptor copolymers: PDTCTTTPD , PDTCTTBT , and PDTCTTPQX , respectively. Field‐effect transistors based on PDTCTTPQX and PDTCTTBT yielded high hole mobilities of 0.017 and 0.053 cm² V^?1 s^?1, respectively, which are among the highest performances among amorphous donor–acceptor copolymers. A bulk heterojunction solar cell that incorporated PDTCTTTPD with the lower‐lying HOMO energy level delivered a higher V_oc value of 0.72 V and a power conversion efficiency (PCE) value of 2.59 %.     

Synthesis and characterization of new low band‐gap polymers containing electron‐accepting acenaphtho[1,2‐c]thiophene‐S,S‐dioxide groups

Two donor–acceptor conjugated polymers, PTSSO‐TT and PTSSO‐BDT, composed of acenaphtho[1,2‐c]thiophene ‐ S,S‐dioxide (TSSO) as a new electron acceptor and thienothiophene (TT) or benzo[1,2‐b:4,5‐b']dithiophene (BDT) as electron donors, were synthesized with Stille cross‐coupling reactions. The number‐averaged molecular weights (M_n) of PTSSO‐TT and PTSSO‐BDT were found to be 15100 and 26000 Da, with dispersity of 1.8 and 2.4, respectively. The band‐gap energies of PTSSO‐TT and PTSSO‐BDT are 1.56 and 1.59 eV, respectively. The HOMO levels of PTSSO‐TT and PTSSO‐BDT are ?5.4 and ?5.5 eV, respectively. These results indicate that the inclusion of TSSO accepting units into polymers is a very effective method for lowering their HOMO energy levels. The field‐effect mobilities of PTSSO‐TT and PTSSO‐BDT were determined to be 1.5 × 10^?3 and 4.5 × 10^?4 cm² V^?1 s^?1, respectively. A polymer solar cell device prepared with PTSSO‐TT as the active layer was found to exhibit a power conversion efficiency (PCE) of 3.79% with an open circuit voltage of 0.71 V under AM 1.5 G (100 mW cm^?2) conditions. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 498–506     

Synthesis and photovoltaic properties of copolymers based on bithiophene and bithiazole

Three simple structured D‐A copolymers, PBTBTz‐1 , PBTBTz‐2 , and PBTBTz‐3 , containing bithiophene (BT) donor unit and bithiazole (BTz) acceptor unit with different alkyl chain length were synthesized by the Pd‐catalyzed Stille‐coupling method. The copolymers were characterized by thermogravimetric analysis, UV–vis absorption, electrochemical cyclic voltammetry, and photovoltaic measurements. The results indicate that the introduction of BTz unit to the polythiophene main chain effectively decreases highest occupied molecular orbital levels of the copolymers and increases the open circuit voltage (V_oc) of polymer solar cells (PSCs) based on the copolymers as donor, and the alkyl chain length influences the photovoltaic properties of the polymers significantly. The PSCs based on PBTBTz‐2 and PBTBTz‐3 show higher V_oc up to 0.77 and 0.81 V, respectively. The power conversion efficiency of the PSC based on PBTBTz‐2 :PC₇₀BM = 1:1(w/w) reached 2.58% with short circuit current of 8.70 mA/cm², under the illumination of AM1.5, 100 mW/cm². © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Random poly(3‐hexylthiophene‐co‐3‐cyanothiophene‐co‐3‐(2‐ethylhexyl)thiophene) copolymers with high open‐circuit voltage in polymer solar cells

For the purpose of developing poly(3‐hexylthiophene) (P3HT) based copolymers with deep‐lying highest occupied molecular orbital (HOMO) levels for polymer solar cells with high open‐circuit voltage (V_oc), we report a combined approach of random incorporation of 3‐cyanothiophene (CNT) and 3‐(2‐ethylhexyl)thiophene (EHT) units into the P3HT backbone. This strategy is designed to overcome CNT content limitations in recently reported P3HT‐CNT copolymers, where incorporation of more than 15% of CNT into the polymer backbone leads to impaired polymer solubility and raises the HOMO level. This new approach allows incorporation of a larger CNT content, reaching even lower‐lying HOMO levels. Importantly, a very low HOMO level of ?5.78 eV was obtained, representing one of the lowest HOMO values for exclusively thiophene‐based polymers. Lower HOMO levels result in higher V_oc and higher power conversion efficiencies (PCE) compared to the previously reported P3HT‐CNT copolymers containing only 3‐hexylthiophene and CNT units. As a result, solar cells based on P3HT‐CNT‐EHT(15:15) , which contains 70% of P3HT, 15% of CNT and 15% of EHT, yield a V_oc of 0.83 V in blends with PC₆₁BM while preserving high fill factor (FF) and high short‐circuit current density (J_sc), resulting in 3.6% PCE. Additionally, we explored the effect of polymer number‐average molecular weight (M_n) on the optoelectronic properties and solar cell performance for the example of P3HT‐CNT‐EHT(15:15). The organic photovoltaic (OPV) performance improves with polymer M_n increasing from 3.4 to 6.7 to 9.6 kDa and then it declines as M_n further increases to 9.9 and to 16.2 kDa. The molecular weight study highlights the importance of not only the solar cell optimization, but also the significance of individual polymer properties optimization, in order to fully explore the potential of any given polymer in OPVs. The broader ramification of this study lies in potential application of these high band gap copolymers with low‐lying HOMO level in the development of ternary blend photovoltaics as well as tandem OPV. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1526–1536     

Novel narrow‐band‐gap conjugated copolymers containing phenothiazine‐arylcyanovinyl units for organic photovoltaic cell applications

A series of novel narrow‐band‐gap copolymers ( P1 ‐ P12 ) composed of alkyl‐substituted fluorene (FO) units and six analogous mono‐ and bis(2‐aryl‐2‐cyanovinyl)‐10‐hexylphenothiazine monomers ( M1 ‐ M6 ) were synthesized by a palladium‐catalyzed Suzuki coupling reaction with two different feed in ratios of FO to M1 ‐ M6 (molar ratio = 3:1 and 1:1). The absorption spectra of polymers P1 ‐ P12 exhibited broad peaks located in the UV and visible regions from 400 to 800 nm with optical band gaps at 1.55–2.10 eV, which fit near the wavelength of the maximum solar photon reflux. Electrochemical experiments displayed that the reversible p‐ and n‐doping processes of copolymers were partially reversible, and the proper HOMO/LUMO levels enabled a high photovoltaic open‐circuit voltage. As blended with [6,6]‐phenyl C₆₁ butyric acid methyl ester (PCBM) as an electron acceptor in bulk heterojunction photovoltaic devices, narrow‐band‐gap polymers P1 ‐ P12 as electron donors showed significant photovoltaic performance which varied with the intramolecular donor‐acceptor interaction and their mixing ratios to PCBM. Under 100 mW/cm² of AM 1.5 white‐light illumination, the device of copolymer P12 produced the highest preliminary result having an open‐circuit voltage of 0.64 V, a short‐circuit current of 2.70 mA/cm², a fill factor of 0.29, and an energy conversion efficiency of 0.51%. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4285–4304, 2008     

Benzo[2,1‐b;3,4‐b′]dithiophene‐based low‐bandgap polymers for photovoltaic applications

The synthesis of four alternating copolymers using benzo[2,1‐b;3,4‐b′]dithiophene (BDP) as the common donor unit is presented. Before the synthesis, theoretical calculations that we performed predicted that the incorporation of BDP, which consists of fused dithiophene units with a benzene ring, into these polymers would produce a low‐lying highest occupied molecular orbital (HOMO) energy level. Low‐lying HOMO levels are desirable to produce high open circuit voltages (V_OC) in organic bulk heterojunction (BHJ) photovoltaic devices. The polymers' structural characterization, as well as the preliminary results of their performance in BHJ devices, using (6,6)‐phenyl C₆₁‐butyric acid methyl ester as the electron acceptor, is presented. The V_OC values follow the expected trend: increasing with decreasing HOMO level of the polymer. High V_OC values of 0.81 and 0.82 V have been obtained from two polymers: PBDPBT and PBDPDPP. The initial power conversion efficiency achieved in these unoptimized devices was 1.11% because of relatively low J_SC values. The variation observed in the J_SC values between the four polymers is discussed. Device performance is expected to increase with optimization of processing conditions for the devices. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of bistriphenylamine‐ and benzodithiophene‐based random conjugated polymers for organic photovoltaic applications

In this study, donor–acceptor random polymers containing benzotriazole acceptor and bistriphenylamine and benzodithiophene donors, P1 and P2 , were successfully synthesized by Stille coupling polymerization. The effect of bistriphenylamine moiety and thiophene π‐conjugated linker on electrochemical, spectroelectrochemical, and optical behaviors of the polymers were investigated. Optoelectronic properties and photovoltaic performance of the polymers were examined under the illumination of AM 1.5G, 100 mW cm^?2. The polymers were characterized by cyclic voltammetry, UV‐Vis‐NIR absorption spectroscopy, gel permeation chromatography. HOMO/LUMO energy levels of P1 and P2 were calculated as ?5.47 eV/–3.41 eV and ?5.43 eV/–3.27 eV, respectively. Bulk heterojunction type solar cells were constructed using blends of the polymers (donor) and [6,6]‐phenyl C₇₁ butyric acid methyl ester (PC₇₁BM) (acceptor). Photovoltaic studies showed that the highest power conversion efficiency of these photovoltaic devices were recorded as 3.50% with open circuit voltage; 0.79 V, short circuit current; 9.45 mA cm^?2, fill factor; 0.53 for P1 :PC₇₁BM (1:2, w/w) in 3% o‐dichlorobenzene (o‐DCB) solution and 3.15% with open circuit voltage; 0.75 V, short circuit current; 8.59 mA cm^?2, fill factor; 0.49 for P2 :PC₇₁BM (1:2, w/w) in 2% chlorobenzene (CB) solution. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 3705–3715     

Low band‐gap modulation of isoindigo‐based copolymers toward high open‐circuit voltage of polymer solar cells

Designing low band‐gap‐conjugated polymers coupled with low HOMO levels attracts great attention in the field of polymer solar cells (PSCs). By using donor–acceptor (D‐A) copolymerization strategy, we designed and synthesized a series of low band‐gap copolymers with deep HOMO levels via introducing an isoindigo (IID) acceptor unit in the copolymers with the donor unit of fluorene (F) (PIID‐F), carbazole (Cz) (PIID‐Cz), thiophene (Th) (PIID‐Th), dithiophene (DTh) (PIID‐DTh), or dithienosilole (DTS) (PIID‐DTS). The HOMO level of the copolymers, measured by electrochemical cyclic voltammetry, varies from ?5.3 eV to ?5.8 eV, depending on different donor units in the copolymers. However, the LUMO levels of all the copolymers are fixed at about ?3.6 eV, which is mainly determined by IID acceptor unit due to its strong electron‐withdrawing ability. The new results will provide an effect help in designing IID based molecular structures. Among the copolymers, PIID‐DTS has a low band gap of 1.58 eV and possesses a low‐lying HOMO energy level of ?5.33 eV. The PSCs based on PIID‐DTS as donor and PC₇₀BM as acceptor exhibited a high open‐circuit voltage (V_oc) of 0.93 V and a primary power conversion efficiency of 2.45%. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 3477–3485     

Synthesis and applications of low‐bandgap conjugated polymers containing phenothiazine donor and various benzodiazole acceptors for polymer solar cells

A series of soluble donor‐acceptor conjugated polymers comprising of phenothiazine donor and various benzodiazole acceptors (i.e., benzothiadiazole, benzoselenodiazole, and benzoxadiazole) sandwiched between hexyl‐thiophene linkers were designed, synthesized, and used for the fabrication of polymer solar cells (PSC). The effects of the benzodiazole acceptors on the thermal, optical, electrochemical, and photovoltaic properties of these low‐bandgap (LBG) polymers were investigated. These LBG polymers possessed large molecular weight (M_n) in the range of 3.85?5.13 × 10⁴ with high thermal decomposition temperatures, which demonstrated broad absorption in the region of 300?750 nm with optical bandgaps of 1.80?1.93 eV. Both the HOMO energy level (?5.38 to ?5.47 eV) and LUMO energy level (?3.47 to ?3.60 eV) of the LBG polymers were within the desirable range of ideal energy level. Under 100 mW/cm² of AM 1.5 white‐light illumination, bulk heterojunction PSC devices containing an active layer of electron donor polymers mixed with electron acceptor [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) or [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) in different weight ratios were investigated. The best performance of the PSC device was obtained by using polymer PP6DHTBT as an electron donor and PC₇₁BM as an acceptor in the weight ratio of 1:4, and a power conversion efficiency value of 1.20%, an open‐circuit voltage (V_oc) value of 0.75 V, a short‐circuit current (J_sc) value of 4.60 mA/cm², and a fill factor (FF) value of 35.0% were achieved. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Donor–acceptor copolymers based on phenanthrene as electron‐donating unit: Synthesis and photovoltaic performances

Using 9,10‐bis(dodecyloxy)phenanthrene as electron‐donating unit and 4,7‐dithienyl‐5,6‐bis(dodecyloxy)benzothiadiazole, 4,7‐dithienyl‐5,6‐bis(octyloxy)benzoxadiazole, 5,8‐dithienyl‐2,3‐bis(para‐octyloxyphenyl)quinoxaline, and 5,8‐dithienyl‐2,3‐bis(meta‐octyloxyphenyl)quinoxaline as electron‐accepting unit, four D–A copolymers PPA‐DTBT , PPA‐DTBX , PPA‐ p ‐DTQ , and PPA‐ m ‐DTQ , respectively, were successfully synthesized as new polymeric donors for photovoltaic cells. All the alternating copolymers can show two absorption bands, both in solutions and thin films. The optical bandgaps of the polymers are quite close, which are between 1.93 and 2.00 eV. The HOMO and LUMO levels of the polymers are also comparable of ?5.52 ± 0.03 eV and ?3.57 ± 0.03 eV, respectively. Thus, using the dialkoxyphenanthrene as the D unit could afford D–A copolymers with deep‐lying HOMO levels, which would be an important factor to achieve high open‐circuit voltages (V_oc) in bulk‐heterojunction solar cells. With the copolymers as the donor and PC₇₁BM as the acceptor, the resulting solar cells could display good V_oc between 0.86 and 0.88 V. Among the four copolymers, PPA‐DTBT containing the dialkoxybenzothiadiazole unit showed the best power conversion efficiency of 3.03% because of its relatively higher hole mobility and better phase separation. The results suggest that dialkoxyphenanthrene is a valuable electron‐donating unit in the constructions of D–A copolymers for efficient solar cells with high V_oc. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4966–4974     

Jacket‐like structure of donor–acceptor chromophores‐based conducting polymers for photovoltaic cell applications

Through the Stille coupling polymerization, a series of soluble acceptor/donor quinoxaline/thiophene alternating conducting polymers with a hole‐transporting moiety of carbazole as a side chain ( PCPQT ) has been designed, synthesized, and investigated. The UV–vis measurement of the charge‐transferred type PCPQT s of different molecular weights with low polydispersity exhibits a red shifting of their absorption maximum from 530 to 630 nm with increasing chain length (M_n: from 1100 to 19,200). The HOMO and LUMO energy levels of PCPQT can be determined from the cyclic voltammetry measurement to be ?5.36 and ?3.59 eV, respectively. Solar cells made from PCPQT/PCBM bulk heterojunction show a high open‐circuit voltage, V_oc of ～0.75 V, which is significantly higher than that of a solar cell made from conventional poly(3‐hexyl thiophene)/ PCBM as the active polymer PCPQT has lower HOMO level. Further improvements are anticipated through a rational design of the new low band‐gap and the structurally two‐dimensional donor–acceptor conducting polymers. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1607–1616, 2010     

Synthesis and Photovoltaic Properties of Thieno[3,4‐c]pyrrole‐4,6‐dione‐based donor–acceptor Copolymers

Three donor–acceptor (D–A) 1,3‐di(thien‐2‐yl)thieno [3,4‐c]pyrrole‐4,6‐dione‐based copolymers, poly{9,9‐dioctylfluorene‐2,7‐diyl‐alt‐1,3‐bis(4‐hexylthien‐2‐yl)‐5‐octylthieno[3,4‐c]pyrrole‐4,6‐dione}, poly{N‐(1‐octylnonyl)carbazole‐2,7‐diyl‐alt‐1,3‐bis(4‐hexylthien‐2‐yl)‐5‐octylthieno[3,4‐c]pyrrole‐4,6‐dione}, and poly {4,8‐bis(2‐ethylhexyloxyl) benzo[1,2‐b:3,4‐b′]dithiophene‐alt‐1,3‐bis(4‐hexylthien‐2‐yl)‐5‐octylthieno[3,4‐c] pyrrole‐4,6‐dione} were synthesized by Suzuki or Stille coupling reaction. By changing the donor segment, the bandgaps and energy levels of these copolymers could be finely tuned. Cyclic voltammetric study shows that the highest occupied molecular orbital (HOMO) energy levels of the three copolymers are deep‐lying, which implies that these copolymers have good stability in the air and the relatively low HOMO energy level assures a higher open‐circuit potential when they are used in photovoltaic cells. Bulk‐heterojunction photovoltaic cells were fabricated with these polymers as the donors and PC₇₁BM as the acceptor. The cells based on the three copolymers exhibited power conversion efficiencies of 0.22, 0.74, and 3.11% with large open‐circuit potential of 1.01, 0.99, and 0.90 V under one sun of AM 1.5 solar simulator illumination (100 mW/cm²). © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and photovoltaic properties of conjugated D–A copolymers based on thienyl substituted pyrene and diketopyrrolopyrrole for polymer solar cells

A new donor‐acceptor conjugated copolymer (PDTPyDPP), comprising 2,7‐di‐2‐thienyl‐4,5,9,10‐tetrakis(hexyloxy)pyrene as a donor and diketopyrrolopyrrole (DPP) as an acceptor, was synthesized. PDTPyDPP showed good solubility in common organic solvents, broad visible absorption from 300 to 900 nm, and a moderate hole mobility up to 6.3 × 10^?3 cm² V^?1 s^?1. The power conversion efficiency of the photovoltaic device based on the PDTPyDPP/PC₇₁BM photoactive layer reached 4.43% with 0.66 V of open‐circuit voltage (V_oc), 10.52 mA cm^?2 of short‐circuit current (J_sc) and 64.11% of fill factor. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3198–3204