用含氟丙烯酸酯无规共聚物制备超疏水膜

用微乳液聚合法制备了丙烯酸全氟烷基乙酯和甲基丙烯酸甲酯的无规共聚物,并对其进行了表征.采用溶剂挥发成膜法一步制备了具有超疏水性的该聚合物膜,水滴在该聚合物膜上的静态接触角可达151°~160°,滚动角小于3°.通过扫描电子显微镜观察发现该聚合物膜表面分布了许多乳突状突起和微孔洞,并具有微米和纳米尺度相结合的复合杂化结构.该类超疏水表面的形成是由适度粗糙的表面和低表面能相互结合引起的.探讨了该类超疏水膜的形成机理.     

一种耐高温氟化聚二氮杂萘酮芳醚憎水材料的合成及性能

由五氟苯肼和2-(4-羟基苯甲酰)苯甲酸制备了AB-型双官能团单体4-(4-羟基苯基)-2-五氟苯基-二氮杂萘酮,以苯做带水剂,在K2CO3的催化下温和的反应条件下通过自身亲核缩聚反应合成了结构规整的氟化聚二氮杂萘酮芳醚材料.用傅里叶衰减全反射红外光谱(FTIR ATR)、氢谱(1H-NMR)、氟谱(19F-NMR)对材料的结构进行了表征.该聚合物的玻璃化转变温度Tg为316℃,Td,5 wt％为491℃,具有良好的热性能;该聚合物薄膜样品测试结果表明该材料具有高的力学性能和绝缘性,拉伸强度超过了60 MPa,表面电阻率为1.8×1015Ω/m2,体积电阻率为5.6×1012Ω/m3;该聚合物在DMAc,DMF,DMSO,NMP,1,1,2,2-四氯乙烷,四氢呋喃,氯仿,吡啶和环丁砜中有良好的溶解性,可加工得到光滑、硬韧的膜;利用表面接触角测定仪考察了不同溶剂体系所得膜材料的表面性能,用DMAc制备膜的接触角为93.3°,用氯仿制备膜的接触角为92.5°,用THF制备膜的接触角为127.1°,接触角大于聚四氟乙烯(112°),且所有考察溶剂中所得膜的接触角都大于90°,具有较好的憎水性.     

纳米二氧化硅粒子对聚氯乙烯膜的表面结构及浸润性能的调控作用

报道了一种简便的调控聚合物材料表面结构及浸润性能的方法.利用流延成膜和纳米二氧化硅粒子的印迹修饰作用,制备出3种具有不同表面结构的聚氯乙烯(PVC)膜,膜的浸润性能表现为与水的接触角从103°的疏水性变为65°的亲水性,再改变至130°的疏水性.扫描电镜结果表明印迹修饰后的PVC膜具有纳米和微米尺寸的凹凸表面结构.通过对比实验证实了溶剂氯仿和NaOH溶液并不影响膜表面的疏水性能.     

氟硅烷自组装单分子膜的制备及其摩擦学性能

利用分子自组装技术制备了全氟辛酰胺丙基硅烷单分子膜,用X射线光电子能谱(XPS)对组装膜的表面元素进行了表征;接触角测试表明,该组装膜具有很好的疏水-疏油性,其对水的接触角高达105°,对正十六烷的接触角为50°.摩擦磨损实验结果表明,全氟辛酰胺丙基硅烷自组装单分子膜可以大大降低基片的摩擦系数,使载玻片的摩擦系数从0.85左右降低到0.14左右,而且低负荷下具有很好的耐磨性.     

含杂环聚芳醚腈酮的亲水改性

为得到适合于耐高温水性涂料用的亲水性树脂,在碱性条件下对含有二氮杂萘酮结构的耐高温聚合物聚芳醚腈酮(PPENK)进行了亲水改性,选定不同反应时间的改性树脂HPPENKa(0.5 h)、HPPENKb(1.5 h)和HPPENKc(3.5 h),测定其玻璃化转变温度(Tg)、热失重温度、水接触角和溶解性,研究改性聚合物的性能变化.结果表明,随着反应时间的延长,氰基转化率提高,水解产物Tg增加,热失重温度有所降低,水解前后的溶解性能有很大变化,亲水性能明显增强,例如,当氰基转化率为93.82%时,HPPENK膜的水接触角达到54.4°,比PPENK膜的水接触角(75.3°)减小了20.9°.同时,甄选不同的反应共溶剂、反应温度以及碱浓度,考察其对反应的影响,结果表明,当反应温度为120℃6、mol/L NaOH溶液、以DMAc作为反应的共溶剂时对反应较为有利.制备了基于3种改性树脂的水分散体,其静置稳定性依次为HPPENKc>HPPENKb>HPPENKa,其中HPPENKc水分散体较稳定,30天内未出现沉淀.改性聚合物的结构经FT IR和1H-NMR表征.     

一种可溶性低表面自由能聚合物的制备及其表面性质

用全氟辛酸和甲基丙烯酸羟丙酯 (HPMA)为原料 ,合成了具有低表面自由能 ( 1 4 2mN m)的聚合物聚甲基丙烯酸全氟辛酰氧丙基酯 (PFPMA) ,接触角的测定表明聚合物具有较好双疏性 (疏水 疏油性 ) ,其对水的接触角高达 1 1 5°,对正十六烷的接触角为 75°.     

含氟硅丙烯酸酯乳液超疏水膜中疏水基团的梯度分布与表面微观结构研究

利用含氟疏水基团的梯度分布,结合草莓形纳米SiO2粒子提供的双重粗糙表面,制备了具有类"荷叶效应"的超疏水涂膜,水接触角达(174.2±2)°,滞后角几乎接近0°.通过原子力显微镜、扫描电镜和水接触角的测试对膜表面形貌及疏水性能进行了表征;探讨了其表面微观结构与表面疏水性能的关系.草莓形复合粒子在膜表面的无规则排列赋予涂膜表面不同等级的粗糙度,使水滴与涂膜表面接触时能够形成高的空气捕捉率,这种微观结构与疏水基团的梯度分布相结合,赋予了含氟硅丙烯酸酯乳液涂膜表面超疏水性能.     

ATRP法合成弹性蛋白接枝共聚物及其性能研究

弹性蛋白经α-溴异丁酰溴化制备了大分子ATRP引发剂溴化弹性蛋白(E-Br), 再以E-Br作为引发剂, 在CuCl/2,2-联吡啶催化体系下, 用原子转移自由基聚合方法合成了弹性蛋白-g-聚甲基丙烯酸-β-羟乙酯接枝聚合物. 用红外光谱(FTIR)、X射线光电子能谱(XPS)、热重分析(TGA)、扫描电镜(SEM)、离子色谱和动态接触角对接枝聚合物进行了表征. 结果表明, PHEMA键接到了弹性蛋白表面; SEM显示接枝改性后弹性蛋白的表面比未改性前光滑, 但改性后样品的热性能均比未改性样品的低, 起始热分解温度由改性前的307 ℃变为265 ℃; 动态接触角实验结果表明, 接枝改性后的样品具有良好的亲水性, 反应72 h后, 其前进角由接枝前的130.45°下降到29.80°.     

超疏水二氧化钛薄膜的制备及其经紫外光照射引发的超亲水性研究

通过水热反应,在玻璃基底上沉积生成TiO₂薄膜,TiO₂薄膜呈花朵状,具有微纳米级的复合结构,在其表面有大量的乳状突起,经辛基三甲氧基硅烷表面修饰后表现出良好的超疏水性,静态接触角为164°,滚动角为4°。经紫外光照射4~6 h后,其表面变为超亲水性,接触角接近0°。用红外光谱,X射线光电子能谱(XPS)对其表面物质及元素进行表征,最后用Cassie理论对膜的润湿性进行了分析。     

铝合金表面超疏水涂层的制备及其耐蚀性能

基于含氟聚氨酯和纳米SiO₂的协同作用, 在铝合金表面成功制备了一层超疏水涂层. 用红外光谱、扫描电镜和电化学测试等技术对超疏水涂层进行了表征和分析. 红外光谱结果表明, 硅烷偶联剂(A1100)成功键合到纳米SiO₂表面. 扫描电镜和接触角测定仪对涂层的表面形貌表征结果表明, 涂层表面存在微米鄄亚微米尺度的粗糙结构, 接触角可达到156°, 滚动角小于5°. 电化学测试(交流阻抗和极化曲线)结果表明, 所得到的涂层极大地提高了铝合金的耐蚀性能.     

质子交换膜用磺化聚芳醚的合成与性能研究

合成了一种用于质子交换膜的新型磺化聚芳醚. 由于特殊单体结构的设计, 在聚合物主链上引入取代基对主链进行保护, 用氯磺酸直接磺化方法在聚芳醚高分子侧基上引入磺酸功能基, 实现了聚合物磺化结构的可控定位合成, 得到了稳定性较好的磺化聚芳醚. 用溶液浇膜法制备了质子交换膜, 考察了质子交换膜的各种性能. 结果表明, 这种膜具有良好的成膜性, 水解性稳定性和优异热稳定性能, 5%的热失重温度为362.3 ℃. 氧化稳定性在80 ℃的Fenton’s试剂(3%的过氧化氢和2 mg/L的FeSO₄)中进行, 膜在69 min时才开始变碎, 表现出良好的氧化稳定性.     

SYNTHESIS AND PROPERTIES OF SULFONATED POLY（ARYLENE ETHER） CONTAINING TRIPHENYL METHANE MOIETIES FROM ISOCYNATE MASKED BISPHENOL

A novel sulfonated poly（arylene ether） containing triphenylmethane moieties was synthesized by the sulfonation of a designed parent polymer using chlorosulfonic acid as sulfonation agent. The sulfonation took place at the para position of the pendant phenyl rings because of the specially designed parent polymer. The position and degree of sulfonation were characterized by ^1H-NMR and elemental analysis. The sulfonated polymers are highly soluble in common organic solvents, such as dimethylsulfoxide, N,N＇-dimethylacetamide, dimethylformamide, ethylene glycol monomethyl ether, and can be readily cast into tough and smooth films from solutions. The films showed good thermal and hydrolysis stabilities. Moreover, Fenton＇s reagent test revealed that the films exhibited superior stability to oxidation. The proton conductivities of the films were comparable with Nation 117 under same conditions. The membrane electrode assembly （MEA） prepared with the asmade film （706 EW, 100 μm dry thickness） shows better cell performance than Nation 115-MEA in the whole current density range.     

Linear and Hyperbranched Poly(arylene ether)s from a New Semifluorinated AB Monomer

A new trifluoromethyl-activated AB monomer has been successfully synthesized by Pd-initiated coupling of 4-bromo anisole with 4-fluoro-3-trifluoromethylphenylboronic acid followed by demethylation. The monomer leads to a semifluorinated poly(arylene ether) by nucleophilic displacement polymerization reaction. The AB monomer has been further copolymerized with a corresponding AB ₂ monomer to form the corresponding semifluorinated hyperbranched (hb) poly(arylene ether). The resulting linear and hb poly(arylene ether)s exhibited weight average molecular weight of 75700 and 144100 g/mol, respectively. The hb copolymer exhibited better solubility in different organic solvents compared to the linear poly(arylene ether). The polymers showed excellent thermal stability up to 522°C at 10% wt loss in air and glass transition temperatures as high as 187°C. The mechanical properties of the linear poly(arylene ether) film 1a exhibited tensile strength at break of 89 MPa, elongation at break of up to 3% and a Young’s modulus value of 2.66 GPa. The films of the polymers were hydrophobic in nature and showed water contact angle as high as 93.6°.     

燃料电池质子交换膜用新型磺化聚芳醚酮的合成和性能表征

报道了一种新型磺化聚芳醚酮材料的合成方法, 通过引入取代基对聚芳醚主链进行保护，用氯磺酸直接磺化方法在聚芳醚酮高分子侧基上引入磺酸功能基, 实现了聚合物磺化结构的可控定位合成, 得到了稳定性较好的磺化聚芳醚酮. 通过核磁共振(NMR)、 热重(TG)和凝胶渗透色谱(GPC)等分析方法对其结构及性能进行了表征. 用溶液浇膜法制备了质子交换膜, 考察了膜的各种性能, 并与商用Nafion膜进行了比较, 其导电性、 热稳定性和吸水性远优于Nafion膜, 抗氧化性、抗水解性和机械强度也达到了较高的指标.     

Synthesis and properties of sulfonated poly(arylene ether) containing tetraphenylmethane moieties for proton‐exchange membrane

A novel sulfonated poly(arylene ether) containing tetraphenylmethane moieties was successfully synthesized by the sulfonation of a designed parent polymer using chlorosulfonic acid as sulfonation agent. The sulfonation took place only at the para position on the pendant phenyl rings because of the specially designed parent polymer. The sulfonation degree can be easily controlled by using different ratios of sulfonation agent to polymer repeating unit. The position and degree of sulfonation were characterized by ¹H NMR and elemental analysis. The sulfonated polymers are highly soluble in common organic solvents, such as dimethylsulfoxide, N,N′‐dimethylacetamide, dimethylformamide, ethylene glycol monomethyl ether, and can be readily cast into tough and smooth films from solutions. The films showed good thermal and hydrolysis stabilities. Moreover, Fenton's reagent test revealed that the membrane exhibited superior stability to oxidation. The proton conductivities of the films were determined to be equivalent with Nafion® 117 under same conditions. The new polymer with sulfonic acid function on pendent phenyl rings can be potentially used as a proton‐exchange membrane for polymer electrolyte membrane fuel cell. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6411–6418, 2005     

Synthesis of phenyl-s-triazine-based copoly(aryl ether)s derived from hydroquinone and resorcinol

A novel series of soluble and heat-resistant copoly(arylene ether phenyl-s-triazine)s (PAEPs) have been prepared for their potent utilities as structural coatings, high-temperature membranes or adhesives. The copolymers have been synthesized via the nucleophilic displacement polymerization of 2,4-bis(4-fluorophenyl)-6-phenyl-1,3,5-triazine (BFPT) with various ratios of hydroquinone (HQ) and resorcinol (RS). A key feature of these copolymers is the incorporation of multiply meta-ether linkages in the polymer chain, which results in an improvement in the solubility of poly(arylene ether phenyl-s-triazine)s in common organic solvents (e.g., N,N’-dimethylacetamide, N,N’-dimethylformamide, N-methyl-2-pyrrolidinone). The new random copolymers exhibit high glass transitions exceeding 241 °C and excellent thermal and thermo-oxidative stabilities associating with decomposition temperatures for 5% mass-loss in excess of 531 °C. These copolymers can be easily cast into tough, clear and creasable films and exhibit good mechanical properties. All copolymers are amorphous except PAEP9010 as evidenced by WAXD. Their solubility increases with an increase in meta-ether linkage content in the polymer backbone, while the crystallinity and the overall thermal stability appear to decrease slightly. This kind of phenyl-s-triazine-based poly(arylene ether) copolymers may be considered a good candidate for using as high-performance polymeric materials.     

Synthesis and properties of novel poly(arylene ether)s and poly(arylene thioether)s based on a pyridazine biphenol or a phthalazine biphenol

Novel sulfur‐containing biphenol monomers were prepared in high yields by the reaction of 4‐mercaptophenol with chloropyridazine or chlorophthalazine compounds. High‐molecular‐weight poly(arylene ether)s were synthesized by a nucleophilic substitution reaction between these sulfur‐containing monomers and activated difluoro aromatic compounds. The inherent viscosities of these polymers ranged from 0.34 to 0.93 dL/g. The poly(pyridazine)s exhibited glass‐transition temperatures greater than 165 °C. The poly(phthalazine)s showed higher glass‐transition temperatures than the poly(pyridazine)s. A polymer synthesized from a bisphthalazinebiphenol and bis(4‐fluorophenyl)sulfone had the highest glass‐transition temperature (240 °C). The thermal stabilities of the poly(pyridazine)s and poly(phthalazine)s showed similar patterns of decomposition, with no significant weight loss below 390 °C. The poly(phthalazine)s were soluble in chlorinated solvents such as chloroform, and the poly(pyridazine)s were soluble in dipolar aprotic solvents such as N,N′‐dimethylacetamide. The soluble poly(pyridazine)s and poly(phthalazine)s could be cast into flexible films from solution. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 262–268, 2007     

Fluorinated heteroaromatic polyethers for low dielectric constant / high temperature applications

Several series of poly(arylene ether)s with trifluoromethyl substituents were prepared and characterized. These materials are potential candidates for the use as low dielectric constant insulators (intermetal dielectrics, IMD, and interlayer dielectrics, ILD) on microchips. Thermal stability up to 450 °C and a dielectric constant below 3 preferably below 2.5) is required for this application. The thermal stability of the poly(arylene ether)s was increased from 320°C to more than 500 °C by optimization of the structure of the repeating unit. The dielectric constant of one of the most promising structures was determined to be 2.8. In addition, plasma polymerized thin films from hexafluorobenzene, tetrafluorobenzene, perfluorotoluene and perfluorodecaline were prepared and characterized with respect to solubility, dielectric constant, adhesion, and thermal stability.     

Self-Crosslinkable poly(arylene ether)s containing pendent phenylenetriazene groups

Self-crosslinkable poly(arylene ether)s 6 , and 8 , containing pendent triazene groups were prepared by nucleophilic substitution reaction of poly(arylene ether)s 5 , and 7 , respectively, with 1-[4-(4-hydroxyphenoxy)phenylene]triazenes, 4 , in the presence of potassium carbonate in N,N-dimethylacetamide. A series of triazenes 4 containing various substituents have been synthesized. Self-crosslinkable polymer 6e containing phenyl-substituted triazene pendants can be crosslinked at 215°C, which is about 40°C lower than the glass transition temperature of the virgin base polymer 5 . The degree of crosslinking can be tailored by varying the concentration of the pendent phenylenetriazene groups in the polymer. After curing, the flexible polymer films (ca. 10 μm thick) exhibit high gel contents, increased glass transition temperatures, improved resistance to organic solvents, and little change in dielectric constant and thermal stability. These self-crosslinkable poly(arylene ether)s are potential candidates for electronic applications. © 1994 John Wiley & Sons, Inc.     

Synthesis and characterization of new semifluorinated linear and hyperbranched poly(arylene ether phosphine oxide)s through B2 + A2 and AB2 approaches

A new phosphorus containing trifluoromethyl-activated bisfluoro B₂ monomer has been synthesized successfully by coupling reaction of 4-methoxyphenylphosphonic dichloride and the Grignard salt of 5-bromo-2-fluorobenzotrifluoride. This monomer was converted to linear poly(arylene ether phosphine oxide)s by nucleophilic displacement of the fluorine atom on the benzene ring with several diphenols. The B₂ monomer was further demethylated to form an AB₂ monomer which on self condensation yielded hyperbranched poly(arylene ether phosphine oxide) with identical phosphorous containing moiety. The products obtained exhibit weight-average molecular weights as high as 600,000 g mol⁻¹ in SEC. These linear and hyperbranched poly(arylene ether phosphine oxide)s showed thermal stability as high as 516 °C for 10% weight loss in TGA in nitrogen and showed glass transition temperatures up to 253 °C in DSC. All the polymers were soluble in a wide range of organic solvents, e.g., CHCl₃, THF, NMP and DMF, however, the hb sample showed a significant lower solution viscosity compared to linear samples of similar molar mass. Transparent thin films of linear poly(arylene ether phosphine oxide)s casted from dichloromethane exhibited tensile strengths up to 50 MPa, a modulus of elasticity up to 0.95 GPa and elongation at break up to 36% depending on their exact repeating unit structures. No free standing films could be prepared from the hb analogue due to the missing entanglements, but stable thin polymer films on silicon wafers with high hydrophobicity were formed which showed water contact angles as high as 91°.