Preparation, structure and ferromagnetic properties of the nanocrystalline Ti1-xMnxO2 thin films grown by radio frequency magnetron co-sputtering

This paper reported that the Mn-doped TiO2 films were prepared by radio frequency （RF） magnetron cosputtering. X-ray diffraction measurements indicate that the samples are easy to form the futile structure, and the sizes of the crystal grains grow big and big as the Mn concentration increases. X-ray photoemlssion spectroscopy measurements and high resolution transmission electron microscope photographs confirm that the manganese ions have been effectively doped into the TiO2 crystal when the Mn concentration is lower than 21%. The magnetic property measurements show that the Ti1-xMnxO2 （x = 0.21） films are ferromagnetic at room temperature, and the saturation magnetization, coercivity, and saturation field are 16.0 emu/cm^3, 167.5 × 80 A/m and 3740 × 80 A/m at room temperature, respectively. The room-temperature ferromagnetism of the films can be attributed to the new futile Ti1-xMnxO2 structure formed by the substitution of Mn^4＋ for Ti^4＋ into the TiO2 crystal .lattice, and could be explained by O vacancy （Vo）-enhanced ferromagnetism model.     

Effects of doping site and pre-sintering time on microstructure and magnetic properties of Fe-doped BaTiO3 ceramics

The A-site substituted BaTiO₃ ceramics were prepared by solid-state reaction via partial substitution of Fe for Ba²⁺. By comparison with the B-site substituted sample made under similar conditions, the effect of Fe doping site on microstructure and magnetism was investigated using X-ray diffraction, Mössbauer spectroscopy and vibrating sample magnetometer. It is found that A-site substitution can be realized to a certain extent at 7 at% Fe addition, whereas impurities are observed at higher Fe concentrations. In the nominal (Ba_0.93Fe_0.07)TiO₃ sample, the Fe ions are present as Fe²⁺ and Fe³⁺, respectively, replacing A-site Ba²⁺ and octahedral B-site Ti⁴⁺ in hexagonal perovskite lattice. The double-exchange Fe²⁺-O²⁻-Fe³⁺ interactions produce ferromagnetism well above room temperature, but the saturation magnetization and the Curie temperature are both obviously lower than those for B-site substitution due to different magnetic exchange mechanisms. In the B-site substituted sample Ba(Ti_0.93Fe_0.07)O₃, the super-exchange interactions between Fe³⁺ on pentahedral and octahedral Ti⁴⁺ sites are responsible for ferromagnetism. These results mean that B-site substitution is a better way for Fe-doped BaTiO₃ system to obtain high-Curie-temperature ferromagnetism. Moreover, increasing pre-sintering time can further improve the magnetism of B-site substituted samples, through which the saturation magnetization for Ba(Ti_0.93Fe_0.07)O₃ is enhanced ∼6 times.     

Dielectric and spectroscopic investigations of lithium aluminium zirconium silicate glasses mixed with TiO2

Li₂O–Al₂O₃–ZrO₂–SiO₂ glasses mixed with different concentrations of TiO₂ (ranging from 0 to 5.0?mol%) were synthesised and their dielectric properties (dielectric constant, loss tan?δ, a.c. conductivity σ) investigated over wide ranges of frequency and temperature. Studies of optical absorption, ESR, infrared (IR) and photoluminescence properties have also been undertaken. A decrease in dielectric parameters with increasing concentrations of TiO₂ has been observed and this is attributed to an increasing proportion of titanium ions occupying network-forming positions rather than going into interstitial positions. A.C. conductivity in the high-temperature region appears to be connected both to electronic transfer and ionic movements, but conduction attributed to such processes seems to be hampered by the entry of titanium ions into the network-forming positions. Analysis of the results of the IR spectral studies have indicated that there is a decreasing degree of disorder in the glass network with increasing TiO₂ content. The optical absorption and ESR spectral studies have revealed that titanium ions exist in both Ti³⁺ and Ti⁴⁺ states in the glasses. Luminescence spectra exhibited an emission band in the visible region and the luminescence efficiency increased with TiO₂ content. The excitation of substitutionally positioned octahedral Ti⁴⁺ ions is identified as being responsible for the observed luminescence emission.     

Electron spin resonance investigation of the substitution of Fe3^＋ for Ti4^＋ ions in rutile TiO2 single crystal

A Fe doped rutile TiO 2 single crystal is grown in an O 2 atmosphere by the floating zone technique.Electron spin resonance (ESR) spectra clearly demonstrate that Fe 3+ ions are substituted for the Ti 4+ ions in the rutile TiO 2 matrix.Magnetization measurements reveal that the Fe:TiO 2 crystal shows paramagnetic behaviour in a temperature range from 5 K to 350 K.The Fe 3+ ions possess weak magnetic anisotropy with an easy axis along the c axis.The annealed Fe:TiO 2 crystal shows spin-glass-like behaviours due to the aggregation of the ferromagnetic clusters.     

An investigation of phase transformation of titania slag using microwave heating

The influences of microwave heating on the phase transformation of titania slag were systematically investigated. The thermal stability, surface chemical functional groups and microstructure of the titania slag before and after microwave heating, at a temperature of 950?°C for 60 min, were also analyzed using thermogravimetry and differential thermal analysis (TG-DSC), Fourier transform infrared spectroscopy (FT-IR) spectrum and scanning electron microscope (SEM), respectively. The TG-DSC analysis revealed that the phase transformation of the titania slag from anatase TiO₂ to rutile TiO₂ occurred between 750 and 1000 °C. The FT-IR rustles demonstrate that the banding form of Ti⁴⁺, Ti³⁺ and Ti²⁺ ions and the methyl groups on the surface of the titania slag has changed and a new chemical bond Ti–OH was formed. The results of SEM showed that a large number of regulation rutile TiO₂ crystals were found on the surface of the microwave-treated samples and the synthetic rutile has been synthesized successfully using microwave heating.     

Structural, magnetic and electronic structure studies of Mn doped TiO2 thin films

We report structural, magnetic and electronic structure study of Mn doped TiO₂ thin films grown using pulsed laser deposition method. The films were characterized using X-ray diffraction (XRD), dc magnetization, X-ray magnetic circular dichroism (XMCD) and near edge X-ray absorption fine structure (NEXAFS) spectroscopy measurements. XRD results indicate that films exhibit single phase nature with rutile structure and exclude the secondary phase related to Mn metal cluster or any oxide phase of Mn. Magnetization studies reveal that both the films (3% and 5% Mn doped TiO₂) exhibit room temperature ferromagnetism and saturation magnetization increases with increase in concentration of Mn doping. The spectral features of XMCD at Mn L_3,2 edge show that Mn²⁺ ions contribute to the ferromagnetism. NEXAFS spectra measured at O K edge show a strong hybridization between Mn, Ti 3d and O 2p orbitals. NEXAFS spectra measured at Mn and Ti L_3,2 edge show that Mn exist in +2 valence state, whereas, Ti is in +4 state in Mn doped TiO₂ films.     

Co离子注入TiO2薄膜的显微结构和磁性研究

利用直流磁控溅射技术在玻璃衬底上沉积了TiO₂薄膜,并对其进行了Co离子注入,最后在真空中500 ℃退火50 min,得到系列薄膜样品. 利用剥离-分散方法制备了薄膜的透射电镜样品,并用扫描电镜(SEM)、X射线能量散射谱(EDX)和高分辨透射电镜(HRTEM)对样品做了近似原位观察,研究了薄膜样品中不同Co离子注入深度的成分分布和显微结构. 结果表明,薄膜呈锐钛矿结构,Co元素主要分布在薄膜表层,Co离子的注入使TiO₂薄膜的晶粒被部分破坏,并形成CoO,而5 关键词： 2薄膜')" href="#">Co注入TiO₂薄膜 电镜原位观察 室温铁磁性     

Investigating the impurity structure for Fe3+ ions doped into rutile titanium dioxide single crystal

The local environment around Fe³⁺ centers in rutile TiO₂ crystals is studied by employing fourth-order perturbation theory formula based on the dominant spin–orbit coupling mechanism. The zero-field splitting parameters (ZFSPs) D and E and crystal field parameters are modeled for the Fe³⁺ ions not only at the substitution Ti⁴⁺ site, but also at the interstitial site with local symmetry D_2h. In order to acquire the best agreement between the calculated ZFSPs and those measured by electron magnetic resonance, the model parameters are adjusted on the basis of several approaches. This enables us to determine the feasible values of the structural distortions resulting from dopant Fe³⁺ ions. Consequently, it is confirmed that Fe³⁺ ions substitute for Ti⁴⁺ sites in rutile TiO₂ crystals.     

Surface state of TiO2 treated with low ion energy plasma

The effect of low pressure radio frequency (rf) plasma treatment on TiO₂ surface states has been studied using X-ray photoelectron spectroscopy. Three different oxidation states of oxygen in untreated TiO₂ powder were observed, which suggests the existence of adsorbed water and carbon on the surface. The ratio of oxygen to titanium (O/Ti) was decreased for the low ion dose plasma treated samples due to desorption of water from the surface. In the case of Ti 2p about 20% of surface states were converted to Ti³⁺ 2p_3/2 state after plasma treatment with a very good stability, whereas untreated TiO₂ remained mostly as Ti⁴⁺ state. A rapid decrease in the ratio of carbon to titanium (C/Ti) at TiO₂ surface was also observed after plasma treatment and more than 90% of carbon atoms were removed from the surface. Therefore, the plasma treatment of TiO₂ has advantages to surface carbon cleaning, increasing O⁻ and Ti³⁺ surface states, hence improving the activity of TiO₂ for different environmental, energy and biological applications.     

Effect of annealing atmosphere on magnetism for Fe-doped BaTiO3 ceramic

Ba(Ti_0.3Fe_0.7)O₃ ceramic was prepared by solid-state reaction and post-annealed in vacuum and oxygen, respectively. The as-prepared and annealed samples are all single-phase, crystallizing in a 6H-BaTiO₃-type hexagonal perovskite structure. Room-temperature ferromagnetism is exhibited in all ceramics. For the as-prepared sample, the super-exchange interactions of Fe³⁺ in different occupational sites (pentahedral and octahedral sites) are expected to produce the ferromagnetism observed. After annealing in vacuum, the magnetization is reduced while the exchange mechanism remains unchanged. On the contrary, O₂ annealing can effectively enhance the magnetization due to the presence of Fe⁴⁺, an unusual valence for iron. The simultaneous presence of Fe³⁺ and Fe⁴⁺ allows new exchange mechanism responsible for the ferromagnetic interaction. The exchange couplings of Fe ions with mixed valences (Fe³⁺ and Fe⁴⁺) determine the magnetic behavior.     

The magnetic phase transition in titanium oxide induced by proton irradiation

We have studied the magnetic properties of ⁵⁷Fe-doped TiO₂ compounds irradiated by proton with 0, 5 and 10 pC/μm². We have observed the enhancement of the magnetic moment, measured by superconducting quantum interference device magnetometer, with increasing proton irradiation ranging from 0 to 10 pC/μm². Mössbauer spectra of proton irradiated Ti_0.99⁵⁷Fe_0.01O₂ samples were taken at room temperature. Two sites of the wing (sextet) and the central (doublet) are shown in the spectra, which suggest the magnetically ordered phase and the paramagnetic phase, respectively. With increasing proton irradiation, the part of Fe³⁺ ions was converted to Fe²⁺ ions by compensation charge. This clearly suggests that the enhancement of magnetic moment after proton irradiation is contributed to the moment by the spin-orbit coupling of Fe²⁺ ions.     

Phosphorescent and thermoluminescent properties of SrAl2O4:Eu,Dy phosphors prepared by solid state reaction method

Long persistent SrAl₂O₄:Eu²⁺ phosphors co-doped with Dy³⁺ were prepared by the solid state reaction method. The main diffraction peaks of the monoclinic structure of SrAl₂O₄ were observed in all the samples. The broad band emission spectra at 497 nm for SrAl₂O₄:Eu²⁺, Dy³⁺ were observed and the emission is attributed to the 4f⁶5d¹ to 4f⁷ transition of Eu²⁺ ions. The samples annealed at 1100–1200 °C showed similar broad TL glow curves centered at 120 °C. The similar TL glow curves suggest that the traps responsible for them are similar. The long afterglow displayed by the phosphors annealed at different temperatures, may be attributed to the Dy³⁺ ions acting as the hole trap levels, which play an important role in prolonging the duration of luminescence.     

氧离子辐照二氧化钛单晶后的结构与磁性

氧离子辐照二氧化钛单晶可以诱发其铁磁性．辐照后在室温下也能观察到二氧化钛的铁磁性,且对温度依赖性较小．结合X射线衍射实验、卢瑟福背散射/沟道实验、拉曼散射实验谱、电子自旋共振实验谱、超导量子干涉仪实验、单位原子随沟道位移实验,测定了晶格的损伤随辐照流强的增加而增加．发现在氧离子辐照二氧化钛时出现了Ti³⁺替代氧空位(O_V)的缺陷复合体,即形成Ti³⁺-OV复合体．这种缺陷复合体导致了局部(TiO_6-x)的拉曼模式的伸展．说明了Ti³⁺结合一个未成对的3d电子是二氧化钛局部铁磁性的起源.     

Room temperature ferromagnetism in vacuum-annealed TiO2 thin films

Thin films of pure TiO₂ have been prepared using both spin-coating and sputter-deposition techniques on sapphire and quartz substrates. The structural characteristics of the films have been investigated in detail using Raman spectroscopy and high-resolution transmission electron microscopy (HRTEM). When annealed in vacuum, all films demonstrate room temperature ferromagnetism, while the air-annealed samples show much smaller, often negligible, magnetic moments. The magnetization of the vacuum-annealed sputtered samples depends on film thickness, with the volume magnetization decreasing monotonically with increasing thickness. Furthermore, the magnetization per unit area also decreases slightly with increasing film thickness. These results suggest that ferromagnetism in the vacuum-annealed TiO₂ films is mediated by surface defects or interfacial effects, but does not arise from stoichiometric crystalline TiO₂.     

Tetragonal distortions of the octahedral environments of Cr3+, Fe3+ and Gd3+ ions in A2CdF4 (A = Rb,Cs) and ACdF3 crystals

Abstract

The tetragonal distortions of local octahedral environments of Cr³⁺, Fe³⁺ and Gd³⁺ ions in Rb₂CdF₄, Cs₂CdF₄, RbCdF₃ and CsCdF₃ crystals have been studied by analyzing their EPR spectra. From the studies, it is found that the tetragonal distortions for Cr³⁺ and Fe³⁺ impurity ions, which substitute Cd²⁺ and have nearly the same ionic radius, are close to each other, whereas that for Gd³⁺ impurity ion, having a larger ionic radius, is larger than those for Cr³⁺ and Fe³⁺ ions in the same crystal. It appears that not only the impurity-ligand distance, but also the tetragonal distortions of impurity centres in crystals are closely related to the size of impurity.     

The effect of additional doping with Nb, Al or Cu on ferromagnetism and conductivity in V-doped TiO2 powders

Rutile Ti_0.94V_0.06O₂ and Ti_0.93V_0.06M_0.01O₂ (M=Nb, Al, and Cu) polycrystalline powders are synthesized by the standard solid-state reaction method. The room-temperature saturation magnetization and resistivity of Ti_0.94V_0.06O₂ powders are 2.5×10⁻³ emu/g (≈0.60×10⁻³μ_B/V) and above 10⁷ Ω cm, respectively. The ferromagnetism weakens remarkably, and the conductivity enhances after additional doping with Nb or Al in V-doped rutile TiO₂ powders. The room-temperature magnetization and resistivity of Ti_0.93V_0.06Cu_0.01O₂ powders are 2.1×10⁻³ emu/g and 1.26×10⁶ Ω cm, respectively. Based on analysis for chemical valence of dopants by the x-ray photoelectron spectroscopy spectra, and using the bound magnetic polaron model, the microscopic mechanisms of ferromagnetism in V-doped rutile TiO₂ powders with or without additional dopants are discussed in detail.     

Theoretical explanation of g factors for Ti ions in LiNbO3 and LiTaO3 crystals

The EPR g factors g_// and g_⊥ for Ti³⁺ ions at the trigonal octahedral Li⁺ sites of LiNbO₃ and LiTaO₃ crystals are calculated from the third-order perturbation formulas of g factors for 3d¹ ion in trigonal symmetry. In the calculations, the crystal-field parameters are obtained from the structural data by using the superposition model. The calculated values are in reasonable agreement with the observed values. The results are discussed.     

Synthesis of Gd2Ti2O7:Eu, V phosphors by sol-gel process and its luminescent properties

A red-emitting phosphor material, Gd₂Ti₂O₇:Eu³⁺, V⁴⁺, by added vanadium ions is synthesized using the sol-gel method. Phosphor characterization by high-resolution transmission electron microscopy shows that the phosphor possesses a good crystalline structure, while scanning electron microscopy reveals a uniform phosphor particle size in the range of 230-270 nm. X-ray photon electron spectrum analysis demonstrates that the V⁴⁺ ion promotes an electron dipole transition of Gd₂Ti₂O₇:Eu³⁺ phosphors, causing a new red-emitting phenomenon, and CIE value shifts to x=0.63, y=0.34 (a purer red region) from x=0.57, y=0.33 (CIE of Gd₂Ti₂O₇:Eu³⁺). The optimal composition of the novel red-emitting phosphor is about 26% of V⁴⁺ ions while the material is calcinated at 800  °C. The results of electroluminescent property of the material by field emission experiment by CNT-contained cathode agreed well with that of photoluminescent analysis.     

Effect of Sr concentration on microstructure and magnetic properties of (Ba1−xSrx)(Ti0.3Fe0.7)O3 ceramics

Fe-doped (Ba_1−xSr_x)TiO₃ ceramics were prepared by solid-state reaction, and ferromagnetism was realized at room temperature. The microstructure and magnetism were modified by the Sr concentration control (0≤x≤75 at%) at a fixed Fe concentration, and the relevant magnetic exchange mechanism was discussed. All the samples are shown to have a single perovskite structure. When increasing the Sr concentration, the phase structure is transformed from a hexagonal perovskite into a cubic perovskite, with a monotonic decrease in lattice parameters induced by ionic size effect. The room-temperature ferromagnetism is expected to originate from the super-exchange interactions between Fe³⁺ on pentahedral and octahedral Ti sites mediated by the O²⁻ ions. The increase in Sr addition modifies two main influencing factors in magnetic properties: the ratio of pentahedral to octahedral Fe³⁺ and the concentration of oxygen vacancies, leading to a gradually enhanced saturation magnetization. The highest value, obtained for Fe-doped (Ba_0.25Sr_0.75)TiO₃, is an order of magnitude higher than that of the Fe-doped BaTiO₃ system with similar Fe concentration and preparation conditions, which may indicate (Ba_1−xSr_x)TiO₃ as a more suitable matrix material for multiferroic research.     

Control of Tisurface defect on TiO2 nanocrystal using various calcination atmospheres as the first step for surface defect creation and its application in photocatalysis

A new development to create the surface defect (Ti³⁺) on TiO₂ was reported in this paper and compared to the common methods which must prepare the crystalline TiO₂ in the first step prior, and then create the surface defect in the second step. In this work, the surface defect creation was performed in the first step coinciding with the crystalline TiO₂ preparation using the sol-gel method. The creation was performed by varying the amounts of oxygen fed during calcination. Based on the CO₂-temperature programmed desorption (CO₂-TPD) and electron spin resonance (ESR) results, the surface defect (Ti³⁺) substantially increased with the amount of oxygen fed. Moreover, the samples resulting from calcination were used as photocatalysts for ethylene decomposition. The reactivity of those samples was also discussed.