Determination of perfluorooctanesulfonate and perfluorooctanoic acid in sewage sludge samples using liquid chromatography/quadrupole time-of-flight mass spectrometry

A new method is developed for the determination of perfluorooctanesulfonate (PFOS) and perfluorooctanoic acid (PFOA) in sewage sludge samples. The analytes in sewage sludge samples are extracted by methanol and formic acid, cleaned by C18 solid-phase extraction, then separated, identified and quantitated by liquid chromatography/quadrupole time-of-flight mass spectrometry (LC–QTOF-MS). A C18 column (150 mm × 2.1 mm, 3.5 μm) with gradient elution of MeOH–H₂O (60:40) containing 5 mmol/L ammonium acetate and MeOH–H₂O (80:20) is used for the chromatographic separation. [M−K]⁻ ions at m/z 498.93 for PFOS and [M−COOH]⁻ ion at m/z 368.97 for PFOA are selected for QTOF-MS in the negative electrospray ionization mode. The detection limits for PFOS and PFOA in sewage sludge samples are 0.5 and 0.8 ng/g, respectively. The spiked recoveries are in the range of 85–114 and 71–98% for PFOS and PFOA, respectively. The proposed method is successfully applied to the analysis of PFOS and PFOA in 16 sewage sludge samples from China. PFOS and PFOA are detected in most sewage sludge samples and the concentrations of PFOS and PFOA are up to 5383 and 4780 ng/g (oven dry weight), respectively.     

Continuous flow system for lead determination by faas in spirituous beverages with solid phase extraction and on-line copper removal

A continuous flow system for the determination of lead in home made spirituous beverages was developed. The determination was based on the formation of a neutral chelate of the element with ammonium pyrrolidine dithiocarbamate, its adsorption onto a minicolumn packed with sodium faujasite type Y synthetic zeolite, followed by elution with methyl isobutyl ketone and determination by flame atomic absorption spectrometry. Ethanol and copper interfere strongly in the determination and therefore, must be separated prior to the analysis. Copper is removed by precipitation with rubeanic acid, while ethanol is eliminated by rotaevaporation. Sample solutions containing Pb²⁺ in the concentration range from 5 to 120 μg l⁻¹ at pH 2.5 could be analyzed, by using a preconcentration time of 3 min. Preconcentration factors from 80 to 140 were achieved for a sample volume of 6 ml and the detection limit varied from 1.4 to 3.5 μg l⁻¹, depending on the matrix composition. The relative standard deviations for 60 μg l⁻¹ Pb was 3.2% (n = 10) and the recovery of spikes (20, 40, 60 and 80 μg l⁻¹) added to the samples was estimated within 92–105% range, suggesting that lead can be quantitatively determined in such samples. Determining lead in several samples by an alternative technique further checked the accuracy. Finally, the concentrations of Pb²⁺ determined in 28 samples of Venezuelan spirituous beverages were in 12.6–370.0 μg l⁻¹ range, depending on the fermenting material based on different mixtures of agave, raw sugar cane and white sugar.     

Analysis of acrylamide in different foodstuffs using liquid chromatography–tandem mass spectrometry and gas chromatography–tandem mass spectrometry

Acrylamide levels over a wide range of different food products were analysed using both liquid chromatography–tandem mass spectrometry (HPLC–MS–MS) and gas chromatography–tandem mass spectrometry (GC–MS–MS). Two different sample preparation methods for HPLC–MS–MS analysis were developed and optimised with respect to a high sample throughput on the one hand, and a robust and reliable analysis of difficult matrices on the other hand. The first method is applicable to various foods like potato chips, French fries, cereals, bread, and roasted coffee, allowing the analysis of up to 60 samples per technician and day. The second preparation method is not as simple and fast but enables analysis of difficult matrices like cacao, soluble coffee, molasses, or malt. In addition, this method produces extracts which are also well suited for GC–MS–MS analysis. GC–MS–MS has proven to be a sensitive and selective method offering two transitions for acrylamide even at low levels up to 1 μg kg⁻¹. For the respective methods the repeatability (n=10), given as coefficient of variation, ranged from 3% (acrylamide content of 550 μg kg⁻¹) to 12% (acrylamide content of 8 μg kg⁻¹) depending on the food matrix. The repeatability (n=3) for different food samples spiked with acrylamide (5–1500 μg kg⁻¹) ranged from 1 to 20% depending on the spiking level and the food matrix. The limit of quantification (referred to a signal-to-noise ratio of 9:1) was 30 μg kg⁻¹ for HPLC–MS–MS and 5 μg kg⁻¹ for GC–MS–MS. It could be demonstrated that measurement uncertainties were not only a result of analytical variability but also of inhomogeneity and stability of the acrylamide in food.     

Ion chromatographic determination of some anions and alkaline cations in liquid crystal materials after ultraviolet irradiation

A method was developed for the quantitative determination of inorganic cations and anions present in liquid crystal materials pretreated with ultraviolet irradiation by ion chromatography. The samples were irradiated at less than 20±2 °C and then pretreated with OnGuard RP and P cartridges to remove the interferential organic compounds prior to ion chromatographic analysis for both cations and anions. With a high capacity and very hydrophilic anion exchange column, four anions (fluoride, chloride, bromide, iodide) were determined in 20 min with gradient of sodium hydroxide. By employing a cation exchange column, five cations (sodium, ammonium, potassium, magnesium, calcium) could be determined in 12 min. The spiked recoveries for the cations and anions were 84.0–108.1% and 86.1–108.2%, respectively.     

Synthesis, structure and oxygen nonstoichiometry of La0.4Sr0.6Co1−yFeyO3−δ

The samples of La_0.4Sr_0.6Co_1−yFe_yO_3−δ (y = 0.2 and 0.4) were prepared using both conventional ceramic technique and nitrate–citrate precursors technique. The phase identification was made by X-ray diffraction method. The refinement of structural parameters from the XRD and neutron diffraction measurements was performed by full profile Rietveld analysis. Neutron diffraction showed that both samples possess distorted perovskite-type structure. Oxygen nonstoichiometry was measured by chemical analysis and thermogravimetry (TG) analysis in the range 20 ≤ T/°C ≤ 900 and 2E-5 ≤ pO₂/atm ≤ 4E-1. TG-experiments indicate a relatively fast and reversible oxygen exchange at pO₂ > 1E-2 atm. Mass saturation occurs at T < 300 °C upon cooling. The absolute value of oxygen nonstoichiometry was determined by iodometric titration measurements. It was found that both samples have practically stoichiometric composition at 300 °C in air and δ increases with increasing temperature and decreasing oxygen partial pressure.     

Mass spectrometry of humic substances of different origin including those from Antarctica A comparative study

Mass spectra of humic acids (HA) from different sampling sites (Antarctica, Brazil, Czech Republic, Mexico and USA) and origin (plant, soil, peat, and coal derived) were obtained by laser desorption/ionization time of flight mass spectrometry (LDI-TOF MS). Optimisation of the experimental conditions are given as the optimal value of the laser energy at 20–30% higher than the threshold. Under these conditions, reproducible mass spectra of HA samples were obtained. In the mass spectra the majority of the peaks are observed in the m/z region 100–1000 Da. Mass spectra fingerprints of HA were analyzed and, in spite of the differences in their origin, a number of common features and profiles (patterns of peaks) were observed in most of the samples. Very similar structural groups (patterns) of the peaks are present in the m/z range 717–918 Da for HA samples of quite different origins, countries or continents.

The tandem LDI-TOF MS and multivariate statistical tools allowed us to extract and elucidate underlying information contained in the mass spectra of the HA samples under study. Applying principal components and cluster analysis, it was, e.g. demonstrated that most of the Antarctica HA samples show distinguishable differences when compared with humic acids from other continents and of different origin.     

The early stages of Saccharomyces cerevisiae yeast suspensions damage in moderate pulsed electric fields

The objectives of this study were to investigate the effects of pulsed electric fields (PEF) application to colloidal suspension of Saccharomyces cerevisiae. The electrical conductivity measurements during the PEF-treatment of S. cerevisiae suspensions were used to monitor the extent of cell damages in the intervals of electric field strength E = 3–15 kV/cm and time of PEF treatment t_PEF = 10⁻⁴ to 1 s. At relatively small fields (E < 7.5 kV/cm) the early stages of yeast cells damages were observed. At such treatment conditions, the damage was incomplete and developed at long time of PEF treatment, below the value of E = 7.5 kV/cm which is commonly referred in literature as a threshold for this culture. Data obtained for the disintegration in conductivity experiments were found in good correlation with direct counting of yeast lethality using light microscopy. The PEF-induced lethality of the yeast cells and size flocs increased with the mixing of suspensions and the increase of temperature.     

Speciation analysis of arsenic and selenium compounds in environmental and biological samples by ion chromatography-inductively coupled plasma dynamic reaction cell mass spectrometer

An inductively coupled plasma mass spectrometer (ICP-MS) was used as an ion chromatographic (IC) detector for the speciation analysis of arsenic and selenium. The arsenic and selenium species studied included arsenite [As(III)], arsenate [As(V)], monomethylarsonic acid (MMA), dimethylarsinic acid (DMA), arsenobetaine (AsB), selenite [Se(IV)] and selenate [Se(VI)]. Gradient elution using (NH₄)₂CO₃ and methanol at pH 9 allowed the chromatographic separation of all species in less than 12 min. Effluents from the IC column were delivered to the nebulization system of ICP-DRC-MS for the determination of arsenic and selenium. The potentially interfering ³⁸Ar⁴⁰Ar⁺ and ⁴⁰Ar⁴⁰Ar⁺ at the selenium masses m/z 78 and 80 were reduced in intensity by approximately 3 orders of magnitude by using 0.6 mL min⁻¹ CH₄ as reactive cell gas in the DRC while an Rpq value of 0.3 was used. Meanwhile, arsenic was determined as the adduct ion ⁷⁵As¹²CHH⁺ at m/z 89, which is more sensitive than ⁷⁵As. The limits of detection for arsenic and selenium were in the range of 0.002–0.01 ng mL⁻¹ and 0.01–0.02 ng mL⁻¹, respectively, based on peak height. The relative standard deviation of the peak areas for five injections of 5 ng mL⁻¹ As and Se mixture was in the range of 2–4%. The concentrations of arsenic and selenium species have been determined in urine samples collected locally. The major As and Se species in urines were AsB, DMA and probably selenosugar at concentration of 20–40, 15–19 and 17–31 ng mL⁻¹, respectively. The recoveries were in the range of 94–105% for all the determinations. This method has also been applied to determine various arsenic compounds in two fish samples. In this study, a simple and rapid microwave-assisted extraction method was used for the extraction of arsenic compounds from fish. The arsenic species were quantitatively leached with an 80% v/v methanol solution in a focused microwave field during a period of 5 min.     

Preparation of novel ion exchange polyurethane foam and its application for separation and determination of palladium in environmental samples

The new strong anion exchanger (PUFIX) from polyurethane foam was prepared by coupling of the primary amine of the foam matrix with ethyl iodide. PUFIX was characterized using different tools (IR spectra, elemental analysis, density and thermal analysis). The sorption properties of the new anion exchanger (PUFIX) and chromatographic behaviour for separation and determination of palladium(II) ions at low concentrations from aqueous iodide or thiocyanate media were investigated by a batch and dynamic processes. The maximum sorption of Pd(II) was in the pH range of 0.3–2. The kinetics of sorption of the Pd(II) by the PUFIX was found to be fast with average values of half-life of sorption (t_1/2) of 3.32 min. The variation of the sorption of Pd(II) with temperature gives average values of ΔH, ΔS, ΔG and ΔE to be −38.3 kJ mol⁻¹, −100.7 J K⁻¹ mol⁻¹, −8.3 and 11.8 kJ mol⁻¹, respectively. The sorption capacity of PUFIX was 1.69 mmol g⁻¹ for Pd(II), preconcentration factors of values ≈250 and the recovery 99–100% were achieved (R.S.D. ≈ 1.24%). The lower detection limit, 1.28 ng mL⁻¹ was evaluated using spectrophotometric method (R.S.D. ≈ 2.46%).     

Interaction of sodium cholate with dioctadecyldimethylammonium chloride vesicles in aqueous dispersion

Mixtures of dioctadecyldimethylammonium chloride (DODAC) cationic vesicle dispersions with aqueous micelle solutions of the anionic sodium cholate (NaC) were investigated by differential scanning calorimetry, DSC, turbidity and light scattering. Within the concentration range investigated (constant 1.0 mM DODAC and varying NaC concentration up to 4 mM), vesicle → micelle → aggregate transitions were observed. The turbidity of DODAC/NaC/water depends on time and NaC/DODAB molar concentration ratio R. At equilibrium, turbidity initially decreases smoothly with R to a low value (owing to the vesicle–micelle transition) when R = 0.5–0.8 and then increases steeply to a high value (owing to the micelle–aggregate transition) when R = 0.9–1.0. DSC thermograms exhibit a single and sharp endothermic peak at T_m ≈ 49 °C, characteristic of the melting temperature of neat DODAC vesicles in water. Upon addition of NaC, T_m initially decreases to vanish around R = 0.5, and the main transition peak broadens as R increases. For R > 1.0 two new (endo- and exothermic) peaks appear at lower temperatures indicating the formation of large aggregates since the dispersion is turbid. All samples are non-birefringent. Dynamic light scattering (DLS) data indicate that both DODAC and DODAC/NaC dispersions are highly polydisperse, and that the mean size of the aggregates tends to decrease as R increases.     

Pungency evaluation of onion cultivars from the Venezuelan West-Center region by flow injection analysis-UV-visible spectroscopy pyruvate determination

A flow injection analysis (FIA) method was developed for the determination of pyruvate in onion cultivars (Allium cepa L.) from the West-Center region of Venezuela. The reference Schwimmer and Weston (1961) (J. Agric. Food Chem. 9 (1961) 301) Batch method was modified and adapted to FIA conditions. The formation kinetic of the 2,4-dinitrophenylhydrazine (DNPH)–pyruvate complex was evaluated at room temperature and at 37 °C. It was demonstrated the suitability of the chromopher formation at room temperature. The optimal values for the FIA parameters were: sample injection volume 3 mL, flow rate 6 mL min⁻¹, reactor length 1.5 m, sodium hydroxide concentration 1.0 mol L⁻¹ and hydrochloric acid concentration 0.5 mol L⁻¹. The working calibration range was extended from 80 mg L⁻¹ (Batch method) to 700 mg L⁻¹ with the FIA set up. The sample dilution step is thus avoided, simplifying the whole analysis process. The pungency in representative samples of the cultivars Yellow granex 438, Ultra Hybrid and Red onion “Sangre de Toro” was evaluated by the flow injection analysis (FIA)–pyruvate method and the results were compared to the reference Batch pyruvate method and to the taste panel test. Non-significant differences were found at the 95% of confidence level between the FIA method and the Batch reference method. Correlation coefficient when comparing the FIA results to the taste panel test was r² = 0.8353. Significant differences (P < 0.05) were found in the pungency of the cultivars, the Ultra Hybrid having the highest pungency. The pungency order from minor to major was: Red onion, Texas Grano 438 and Ultra Hybrid.     

Determination of dioxopromethazine hydrochloride by capillary electrophoresis with electrochemiluminescence detection

The paper presents a rapid method for the determination of dioxopromethazine hydrochloride (DPZ), an antihistamine drug, by the capillary electrophoresis with electrochemiluminescene detection (CE–ECL) using tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) reagent. This CE–ECL detection method has high sensitivity, good selectivity and reproducibility for DPZ analysis. Under the optimized conditions: separation capillary, 38 cm length (25 μm i.d.); sample injection, 10 s at 8 kV; separation voltage, 12.5 kV; running buffer, 20 mmol L⁻¹ sodium phosphate of pH 6.0; detection potential, 1.15 V; 50 mmol L⁻¹ of phosphate buffer (pH 7.14) containing 5 mmol L⁻¹ of Ru(bpy)₃²⁺ in ECL detection cell, the detection limit of DPZ was 0.05 μmol L⁻¹ (S/N = 3). The linear range extended from 5 to 100 μmol L⁻¹. The linear curve obtained was Y = 181.62 + 9.28X with a correlation coefficient of 0.9970. The relative standard deviations of the ECL intensity and the migration time for six continuous injections of 5 μmol L⁻¹ DPZ were 3.7% and 0.92%, respectively. The CE–ECL method was applied to analyze DPZ in real samples including tablets, rat serum and human urine, and satisfactory results were obtained without interference from samples matrix. The CE–ECL technique was proved to be a potential method for the detection of DPZ in clinic analysis.     

Layered double hydroxides for ultrathin hybrid film preparation using layer-by-layer and spin coating methods

In our work, the synthesis and the structural properties of various layered double hydroxides (LDHs) were investigated. LDHs were prepared from metal salts with sodium hydroxide in aqueous medium at various molar ratios. Nitrate salts of, Mg²⁺, Ca²⁺, Co²⁺, Al³⁺ and acetate salt of Zn²⁺ were applied as precursors. The concentrations of LDH suspensions were in the range of 0.1–1 g/100 ml. The particle size and zeta-potential of LDH particles were measured by dynamic light scattering (DLS). The structure properties of LDHs were analyzed by several methods, namely XRD, UV-vis spectroscopy and AFM. We used the layer-by-layer dipping immersion technique and the spin coating method for the preparation of multilayer films from LDHs on glass surfaces. The cleaned glass surface has a negative surface charge, which is compensated by the positively charged LDH particles. Different negatively charged binders poly(sodium 4-styrenesulfonate), (PSS); poly(acryl-acid), (PAA) were utilized for the preparation of layer-by-layer films. Layer thickness was calculated from absorbance measurements by spectrophotometry and mass determination of the glass surface. Typical film thicknesses were in the range of 19–70 nm/layer and 6–40 μg/cm²/layer depending on the type of LDH and preparation technique. After n = 20 immersion cycles, maximal layer thickness was 1405 nm for 20 layers of 2:1 ZnAl–LDH/PSS film. The film preparation methods tested were compared and it was established that the films obtained by the layer-by-layer method are more stable but thicker than those prepared using the spin coating method.     

Magnetic nanoparticles with hybrid shape

Co₅₀Ni₅₀ particles with very unusual shapes, resembling dumbbells or diabolos, are obtained by reducing mixtures of cobalt and nickel acetates in sodium hydroxide solution in 1,2-propane diol. These particles consist of a central column richer in cobalt than the overall composition, capped with two terminal platelets that are richer in nickel. These hybrid shapes are the result of a two-step growth mechanism due to a difference in reactivity of the two metal ions. The sodium hydroxide concentration controls the length and diameter of the column, in the ranges 50–250 nm and 5–15 nm, respectively, and the diameter of the platelets in the range 25–50 nm. The X-ray diffraction patterns show a mixture of hcp and fcc phases in various proportions depending on the particle shape. High-resolution electron microscopy shows that the hcp phase is located mainly in the central column and the fcc phase mainly in the terminal platelets. The particles are ferromagnetic at room temperature. When the volume fraction of the central column is high enough and the hcp phase is predominant and not much faulted, high coercivity (up to 1900 Oe) is observed.     

Multi-pumping flow system for the determination, solid-phase extraction and speciation analysis of iron

A multi-pumping flow system (MPFS) for the spectrophotometric determination, solid-phase extraction (SPE) and speciation analysis of iron at a wide range of concentrations is proposed. Chelating (iminodiacetic groups) disks have been used as solid phase. A solenoid valve allows the deviation of the flow towards the chelating disk to carry out SPE procedures. The possibility to combine solenoid micro-pumps with solenoid valves increases the versatility of MPFS. Ammonium thiocyanate has been chosen as chromogenic reagent for Fe(III). The determination of total iron is achieved by the on-line oxidation of iron(II) to iron(III) with a hydrogen peroxide stream.

A mass calibration was run within the range 0.01–1.75 μg. The detection limit (3s_b/S) was 0.01 μg. The repeatability (R.S.D.) was estimated as 1.6% after 10-fold processing of 2 ml of 0.5 mg l⁻¹ Fe solution. When SPE was not required, two linear calibration graph within the ranges 0.05–10 and 0.2–15 mg l⁻¹ for the determination of iron(III) and total iron, respectively, were obtained. The proposed procedure was validated by analysis of certified reference materials. The analytical features were compared with those obtained exploiting MSFIA.     

Thermal decomposition of zinc carbonate hydroxide

This study is devoted to the thermal decomposition of two zinc carbonate hydroxide samples up to 400 °C. Thermogravimetric analysis (TGA), boat experiments and differential scanning calorimetry (DSC) measurements were used to follow the decomposition reactions. The initial samples and the solid decomposition products were analyzed by scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared (FTIR) and laser particle size analyzer. Results showed that zinc carbonate hydroxide decomposition started at about 150 °C and the rate of decomposition became significant at temperatures higher than 200 °C. The apparent activation energies (E_a) in the temperature range 150–240 °C for these two samples were 132 and 153 kJ/mol. The XRD analyses of the intermediately decomposed samples and the DSC results up to 400 °C suggested a single-step decomposition of zinc carbonate hydroxide to zinc oxide with not much change in their overall morphologies.     

Ignition characteristics of forest species in relation to thermal analysis data

The ignitability of various forest species was measured with a specifically designed apparatus, under precisely controlled temperature and airflow conditions. The ignitability tests were based on ignition delay time versus temperature measurements using five different forest species: Pinus halepensis, Pistacia lentiscus, Cupressus sempervirens, Olea europaea, Cistus incanus. These species are common in the Mediterranean region and frequently devastated by forest fires. The ignition characteristics of the forest fuels examined were related to thermogravimetric analysis data. The DTG curves showed that the mass changes related to cellulose decomposition in the temperature range of 320–370 °C are greatly responsible for the ignition behavior of the species tested. In addition, the mass of volatiles evolving between 120–160 °C has a significant effect on the ignitability. On the contrary, the inorganic ash content of forest fuels, measured by atomic absorption spectroscopy, seems to play an insignificant role on the ignitability characteristics of the forest fuels examined.     

Determination of cadmium in paint samples by graphite furnace atomic absorption spectrometry with optical temperature control

A graphite furnace atomic absorption spectrometry (GFAAS) method with optical temperature control for the determination of trace cadmium in paint samples is described. Optical temperature control was superior in many respects to current temperature control. The sensibility increased by 60%, the linear range widened by 60%, and the life of graphite tube showed a 200–300% increase because atomization temperature was lowered distinctly and atomization time was shortened. Use of lanthanum chloride as a matrix modifier was investigated. The linear range of calibration curve was 0–24 ng mL⁻¹. The detection limit was 9.6 ng L⁻¹. The characteristic mass was 3.0 pg. The method also resulted in excellent reproducibility (≤2.5% R.S.D.) at such low levels, and the recovery of added cadmium in paint samples was from 94.6% to 102%. This method is readily applicable to the determination of cadmium in paint samples.     

Langmuir monolayer properties of the fluorinated-hydrogenated hybrid amphiphiles with dipalmitoylphosphatidylcholine (DPPC)

Surface pressure–area (π–A), surface potential–area (ΔV–A), and dipole moment–area (μ–A) isotherms were obtained for the Langmuir monolayer of two fluorinated-hydrogenated hybrid amphiphiles (sodium phenyl 1-[(4-perfluorohexyl)-phenyl]-1-hexylphosphate (F6PH5PPhNa) and (sodium phenyl 1-[(4-perfluorooctyl)-phenyl]-1-hexylphosphate (F8PH5PPhNa)), DPPC and their two-component systems at the air/water interface. Monolayers spread on 0.02 M Tris buffer solution (pH 7.4) with 0.13 M NaCl at 298.2 K were investigated by the Wilhelmy method, ionizing electrode method and fluorescence microscopy. Moreover, the miscibility of two components was examined by plotting the variation of the molecular area and the surface potential as a function of the molar fraction for the fluorinated-hydrogenated hybrid amphiphiles on the basis of the additivity rule. The miscibility of the monlayers was also examined by construction of two-dimensional phase diagrams. Furthermore, assuming the regular surface mixture, the Joos equation for analysis of the collapse pressure of two-component monolayers allowed calculation of the interaction parameter (ξ) and the interaction energy (−Δ) between the fluorinated-hydrogenated hybrid amphiphiles and DPPC. The observations by a fluorescence microscopy also supported our interpretation as for the miscibility in the monolayer state. Comparing the monolayer behavior between the two binary systems, no remarkable difference was found among various aspects. Among the two combinations, the mole fraction dependence in monlayer properties was commonly classified into two ranges: 0 ≤ X ≤ 0.3 and 0.3 < X ≤ 1. Dependence of the chain length of fluorinated part was reflected for the molecular packing and surface potential.     

A simultaneous TG–DTA study of the thermal decomposition of 2-hydroxybenzoic acid, 2-carboxyphenyl ester (salsalate)

Simultaneous thermogravimetry–differential thermal analysis (TG–DTA) and gas and liquid chromatography with mass spectrometry detection have been used to study the kinetics and decomposition of 2-hydroxybenzoic acid, 2-carboxyphenyl ester, commercially known as salsalate. Samples of salsalate were heated in the TG–DTA apparatus in an inert atmosphere (100 ml min⁻¹ nitrogen) in the temperature range 30–500 °C. The data indicated that the decomposition of salsalate is a two-stage process. The first decomposition stage (150–250 °C) had a best fit with second-order kinetics with E_a=191–198 kJ/mol. The second decomposition stage (300–400 °C) is described as a zero-order process with E_a=72–80 kJ/mol. The products of the decomposition were investigated in two ways:

(a)Salsalate was heated in a gas chromatograph at various isothermal temperatures in the range 150–280 °C, and the exit gas stream analyzed by mass spectrometry (GC–MS). This approach suggested that salsalate decomposes with the formation of salicylic acid, phenol, phenyl salicylate, and cyclic oligomers of salicylic acid di- and tri-salicylides.

(b)One gram samples of salsalate were heated in a vessel under nitrogen to 150 °C, and the residues were analyzed by liquid chromatography–mass spectrometry (LC–MS). The major compound detected was a linear tetrameric salicylate ester.