The WO3/WS2 nanostructures: Preparation,characterization and optical absorption properties

The WO₃/WS₂ nanostructures were successfully prepared using a two-step hydrothermal/gas phase method. The physical properties of the nanostructures were characterized using XRD, SEM, TEM, UV–visible spectroscopy. The WO₃/WS₂ nanostructures obtained were coexistence of WO₃ and WS₂ in the same particle. The WO₃/WS₂ nanostructures contained a wide and intensive absorption in the UV–visible light region of 245–750 nm, which showed that the WO₃/WS₂ nanostructures may have a potential application as an UV–visible photocatalyst.     

Visible light sensitization effect of polyaminobenzoate adsorbed on TiO2 nanocrystal surface

Poly-o-aminobenzoate (POA) was prepared by oxidizing o-aminobenzoic acid with (NH₄)₂S₂O₈ in an acidic solution. POA was adsorbed on TiO₂ nanocrystal surface to obtain a POA-TiO₂ nanocomposite. The polymerization reaction, structure, adsorption reaction on TiO₂ surface, and visible light sensitization effect of the polymer adsorbed on TiO₂ surface were studied by FT-IR and UV-visible spectra, cyclic voltammetry, and measurements of visible light photoelectrochemical and photocatalytic activities. Three kinds of POA with different long conjugate structures can be formed. These polymers have large absorbance in wide visible light region. POA molecules can be adsorbed on TiO₂ surface by anchoring their carboxylate groups to the TiO₂ surface with a multi-bridging chelating mode, which causes formation of the POA-TiO₂ nanocomposite with a high stability. POA adsorbed on the TiO₂ nanocrystal showed high visible light sensitization effect in the photocatalytic reaction.     

Synthesis and photochemical properties of HTaWO6/ (Pt,TiO2) nanocomposite under visible light irradiation

A new layered nanocomposite, HTaWO₆/(Pt, TiO₂) was synthesized using n-type semi-conductor HTaWO₆ as a host material. HTaWO₆ and HTaWO₆/TiO₂were white, while both HTaWO₆/Pt and HTaWO₆/(Pt, TiO₂) were yellow. The yellow color might be attributed to H_1-xTaWO_6-x/2 formed by the photo-induced phase transformation promoted by Pt. Although HTaWO₆/Pt showed absorption in visible light region (λ > 400 nm), the hydrogen evolution activity was negligibly small. On the other hand HTaWO₆/(Pt, TiO₂) showed excellent photocatalytic activities even under visible light irradiation. The sample containing rutile type titania such as TiO₂(P-25) also showed hydrogen evolution activity, but the activity was smaller than that of HTaWO₆/(Pt, TiO₂). These results suggested that rutile type titania, which can be excited by visible light of wavelength less than 413 nm, played an important role in the visible light-induced photocatalytic activity. The improvement of the hydrogen evolution activity of rutile type titania by intercalating into HTaWO₆/Pt may be due to the depression of the recombination of photoinduced electrons and holes by the heterogeneous electron transfer from rutile type TiO₂ to HTaWO₆/Pt.     

Diatom-templated TiO2 with enhanced photocatalytic activity: biomimetics of photonic crystals

The siliceous frustules with sophisticated optical structure endow diatoms with superior solar light-harvesting abilities for effective photosynthesis. The preserved frustules of diatom (Cocconeis placentula) cells, as biophotonic crystals, were thus employed as both hard templates and silicon resources to synthesize TiO₂ photocatalyst. Characterizations by a combination of physicochemical techniques proved that the bio-inspired sample is TiO₂-coated SiO₂ with biogenic C self-doped in. It was found that the synthesized composites exhibited similar morphologies to the original diatom templates. In comparison with commercial Degussa P25 TiO₂, the C-doped TiO₂/SiO₂ catalyst exhibited more light absorption in the visible region and higher photocatalytic efficiency for photodegradation of rhodamine B under visible light due to the biomorphic hierarchical structures, TiO₂ coating and C-doping.     

Properties of carbon and iron modified TiO2 photocatalyst synthesized at low temperature and photodegradation of acid orange 7 under visible light

The nanoparticles of TiO₂ modified with carbon and iron were synthesized by sol-gel followed solvothermal method at low temperature. Its chemical composition and optical absorption were investigated by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), photoluminescence emission spectroscopy (PL), UV-vis absorption spectroscopy, and electron paramagnetic resonance (EPR). It was found that carbon and iron modification causes the absorption edge of TiO₂ to shift the visible light region. Fe(III) cation could be doped into the matrix of TiO₂, by which could hinder the recombination rate of excited electrons/holes. Superior photocatalytic activity of TiO₂ modified with carbon and iron was observed for the decomposition of acid orange 7 (AO7) under visible light irradiation. The synergistic effects of carbon and iron in modified TiO₂ nanoparticles were responsible for improving visible light photocatalytic activity.     

Synergetic Photocatalytic Nanostructures Based on Au/TiO2/Reduced Graphene Oxide for Efficient Degradation of Organic Pollutants

Recently, there is crucial interest in the design and fabrication of nanocatalysts for efficient decomposition of organic pollutants in wastewater using visible light. This work reports the assembling fabrication of synergetic photocatalytic Au/TiO₂/RGO nanostructures by utilizing the reduced graphene oxide (RGO) as substrate material and efficient separator for electrons and holes. The Au/TiO₂ nanostructures with a ≈7 nm TiO₂ particles size are dispersed uniformly on RGO nanosheets. UV–vis diffuse reflectance spectroscopy verifies that Au/TiO₂/RGO nanocomposites show strong absorption of visible light. The degradation efficiency after 1 h for hydroquinone under visible light and UV light is ≈77% and ≈90%, respectively. Under visible light, the calculated apparent rates (k ) of the Au/TiO₂/RGO nanocomposites are 0.0112 and 0.0174 min^?1 for decomposition of methylene blue and hydroquinone. That are five times greater than that of bare TiO₂. The high photocatalytic activity is mainly attributed to the synergy between RGO and Au/TiO₂ nanostructure. The strategy of composite nanostructures assembling on RGO is ensured to have a great practicable potential for the designing of high efficient multielement composite nanoparticles catalysts.     

Enhanced visible light photocatalytic properties of Fe-doped TiO2 nanorod clusters and monodispersed nanoparticles

In order to get photocatalysts with desired morphologies and enhanced visible light responses, the Fe-doped TiO₂ nanorod clusters and monodispersed nanoparticles were prepared by modified hydrothermal and solvothermal method, respectively. The microstructures and morphologies of TiO₂ crystals can be controlled by restraining the hydrolytic reaction rates. The Fe-doped photocatalysts were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), UV-vis absorption spectroscopy (UV-vis), N₂ adsorption-desorption measurement (BET), and photoluminescence spectroscopy (PL). The refinements of the microstructures and morphologies result in the enhancement of the specific surface areas. The Fe³⁺-dopants in TiO₂ lattices not only lead to the significantly extending of the optical responses from UV to visible region but also diminish the recombination rates of the electrons and holes. The photocatalytic activities were evaluated by photocatalytic decomposition of formaldehyde in air under visible light illumination. Compared with P25 (TiO₂) and N-doped TiO₂ nanoparticles, the Fe-doped photocatalysts show high photocatalytic activities under visible light.     

First-principles study of nitrogen defect g-C3N4/WS2 heterojunction on photocatalytic activity

In this work, first-principles density functional theory simulations have been performed to investigate the influence of nitrogen (N) defect on the supercell structure, electronic structure and photocatalytic properties of g-C₃N₄/WS₂ heterojunctions. Analyses of calculated binding energies and the lattice mismatch ratios led us to confirm that N-deficient g-C₃N₄ and WS₂ were in parallel contact and form a stable heterojunction. Furthermore, the work functions, molecular dynamics simulations, charge density differences, band structures, DOS, electronic and optical properties and absorption spectra of different g-C₃N₄/WS₂ heterojunctions have been analyzed in detail. It is revealed that the compositing of N-deficient g-C₃N₄ with WS₂ improves the separation of photoinduced electron-hole pairs. N-defect enhances the visible light absorption of the heterojunction, due to the introduction of impurity energy levels. Moreover, the introduction of defect species further improves the photocatalytic performance of g-C₃N₄/WS₂ heterojunction in the visible region.     

Influence of tungsten doping concentration on the electronic and optical properties of anatase TiO2

The structural, electronic and optical properties of tungsten-doped TiO₂ have been investigated using density functional theory with plane wave basis sets and ultrasoft pseuodopotential. Substitutional W doping at Ti sites create W 5d states just below the conduction band minimum while interstitial W doping gives isolated W 5d states in the middle of forbidden region. Averaged bond lengths show that W doping at Ti sites produce minimum structural distortion as compared to the interstitial W-doped TiO₂. Substitutional W-doped TiO₂ has better visible light absorption compared to interstitial W-doped TiO₂ and has stable configuration which provide reasonable explanation for the experimental findings. Tungsten doping in TiO₂ with different doping concentrations is investigated as an enabling concept for enhancing the visible light absorption. Optical properties show that optimal W doping concentration would improve the visible light absorption. 2.08% W doping concentration gives strong visible and ultraviolet light absorption among all doped models found consistent with experiments.     

Doping mode, band structure and photocatalytic mechanism of B-N-codoped TiO2

The photocatalyst B and N codoped TiO₂ (B-N-TiO₂) was prepared via the sol-gel method by using boric acid and ammonia as B and N precursors. The doping mode, band structure and photocatalytic mechanism of B-N-TiO₂ were investigated well and elucidated in detail. B-N-TiO₂ showed the narrowed band gap and thus extended the optical absorption due to interstitial N and [NOB] species in the TiO₂ crystal lattice. The coexistence of interstitial N and [NOB] species in the TiO₂ crystal lattice and surface NO_x species allowed the more efficient utilization of visible light. Simultaneously, interstitial [NOB] and N species and surface B₂O₃ and NO_x species facilitated the separation of photo generated electrons and holes and suppress their recombination effectively. Hence, B-N-TiO₂ showed a higher photocatalytic activity than pure TiO₂, N-doped TiO₂ (N-TiO₂) and B-doped TiO₂ (B-TiO₂) under both UV and visible light irradiation.     

A combined experimental and theoretical analysis of Fe-implanted TiO2 modified by metal plasma ion implantation

Photocatalyst titanium dioxide (TiO₂) thin films were prepared using sol-gel process. To improve the photosensitivity of TiO₂ at visible light, transition metal of Fe was implanted into TiO₂ matrix at 20 keV using the metal plasma ion implantation process. The primary phase of the Fe-implanted TiO₂ films is anatase, but X-ray diffraction revealed a slight shift of diffraction peaks toward higher angles due to the substitutional doping of iron. The additional band gap energy levels were created due to the formation of the impurity levels (Fe-O) verified by X-ray photoelectron spectroscopy, which resulted in a shift of the absorption edge toward a longer wavelength in the absorption spectra. The optical band gap energy of TiO₂ films was reduced from 3.22 to 2.87 eV with an increase of Fe ion dosages from 0 to 1 × 10¹⁶ ions/cm². The band gap was determined by the Tauc plots. The photocatalysis efficiency of Fe-implanted TiO₂ was assessed using the degradation of methylene blue under ultraviolet and visible light irradiation. The calculated density of states for substitutional Fe-implanted TiO₂ was investigated using the first-principle calculations based on the density functional theory. A combined experimental and theoretical Fe-implanted TiO₂ film was formed, consistent with the experimentally observed photocatalysis efficiency of Fe-implanted TiO₂ in the visible region.     

Preparation and photocatalytic activity of nitrogen-doped TiO2 hollow nanospheres

TiO₂ hollow nanospheres were prepared using silicon oxide as a template. N-doped titanium oxide hollow spheres, TiO_2−xN_x were synthesized by reacting TiO₂ hollow spheres with thiourea at 500 °C. XRD and XPS data showed that oxygen was successfully substituted by nitrogen through the nitrogen-doping reaction, and finally N-doped TiO₂ hollow spheres were formed. The N-doped TiO₂ hollow spheres showed new absorption shoulder in visible light region so that they were expected to exhibit photocatalytic activity in the visible light. The photocatalytic activity of N-doped TiO₂ hollow spheres under visible light was similar to that of normal spherical TiO_2−xN_x in spite of the structural difference.     

Preparation of N-doped TiO<Subscript>2</Subscript> photocatalyst by atmospheric pressure plasma process for VOCs decomposition under UV and visible light sources

The nitrogen doped (N-doped) titanium dioxide (TiO₂) photocatalyst was prepared by the atmospheric-pressure plasma-enhanced nanoparticles synthesis (APPENS) process operated under normal temperature, i.e. the dielectric barrier discharge plasma process. The N₂ carrier gas is dissociated in the AC powered nonthermal plasma environment and subsequently doped into the TiO₂ photocatalyst that was capable of being induced by visible light sources. The APPENS process for producing N-doped TiO₂ showed a higher film deposition rate in the range of 60–94 nm/min while consuming less power (<100 W) as compared to other plasma processes reported in literatures. And the photocatalytic activity of the N-doped TiO₂ photocatalyst was higher than the commercial ST01 and P25 photocatalysts in terms of toluene removals in a continuous flow reactor. The XPS measurement data indicated that the active N doping states exhibited N 1s binding energies were centered at 400 and 402 eV instead of the TiN binding at 396 eV commonly observed in the literature. The light absorption in the visible light range for N-doped TiO₂ was also confirmed by a clear red shift of the UV-visible spectra.     

TiO2/carboxylate-rich porous carbon: A highly efficient visible-light-driven photocatalyst based on the ligand-to-metal charge transfer (LMCT) process

A novel visible-light-driven photocatalyst based on TiO₂/carboxylate-rich porous carbon composite (TiO₂/CRPC) was successfully synthesized by low temperature carbonization process in air. Sodium gluconate plays a crucial role in the formation of TiO₂/CRPC. Different functional groups of sodium gluconate play synergetic roles in the formation of TiO₂/CRPC. XRD and Raman spectra studies indicated that there are two different TiO₂ crystalline phases existing in TiO₂/CRPC, which are anatase and brookite, and the CRPC is amorphous. Via FT-IR and XPS spectra investigations, it was demonstrated that carboxylate group, the ligand-to-metal charge transfer (LMCT) forming functional group, was solidified into the CRPC and form the LMCT complex on TiO₂ surface through the fabrication of TiO₂/CRPC. Compared with the pure TiO₂, TiO₂/CRPC exhibit enhanced absorption in the UV and visible light region around 260–600 nm. The strong absorption in the visible light region gives TiO₂/CRPC advantages over pure TiO₂ for the degradation of organic pollutants. TiO₂/CRPC can activate O₂ in air under mild conditions and exhibit excellent visible-light-driven photocatalytic activities. However, TiO₂/C composite obtained by using glucose instead of sodium gluconate exhibits poor photocatalytic activity, which demonstrated that carboxylate–TiO₂ complexes are responsible for the prominent photocatalytic properties of TiO₂/CRPC under visible light irradiation.     

Sol-gel derived S,I-codoped mesoporous TiO2 photocatalyst with high visible-light photocatalytic activity

A mesoporous S,I-codoped TiO₂ photocatalyst with high visible light photocatalytic activity was synthesized through the hydrolysis and condensation of titanium isopropoxide with thiourea and iodic acid as the precursors. The as-prepared catalysts were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), UV-vis diffuse reflectance (DRS), X-ray photoelectron spectroscopy (XPS), Fourier translation infrared spectroscopy (FT-IR), and N₂ adsorption. The results showed that the cations of S⁶⁺ and I⁵⁺ could substitute for some of the lattice titanium (Ti⁴⁺). The S,I-codoping forms the new bands above the valence band and narrows the band-gap of the TiO₂, then shifts the absorption edge from UV light region to visible light range. The activity of the catalyst was examined by photodegradation of methylene blue in an aqueous solution under visible light irradiation. The activity of the S,I-codoped catalyst is far superior to that of single S or I-doped TiO₂ counterpart. The high visible light photocatalytic activity could be attributed to the strong absorption of light, well-crystalline anatase phase, and mesoporous microstructure.     

P掺杂锐钛矿相TiO2的第一性原理计算

利用基于密度泛函理论的第一性原理对不同P掺杂形式(P替位Ti, P替位O, 间隙P)的锐钛矿相TiO₂的晶格常数、电荷布居、能带结构、分态密度和吸收光谱进行了计算. 结果表明, P替位Ti时, TiO₂体积减小, P替位O和间隙P的存在使TiO₂的体积膨胀; 替位Ti的P和间隙P均有不同程度的氧化, 而替位O的P带有负电荷. 三种P掺杂形式均导致锐钛矿相TiO₂禁带宽度的增大, 并在TiO₂禁带之内引入了掺杂局域能级. P掺杂导致TiO₂禁带宽度增大的程度依次为: 间隙P>P替位Ti>P替位O. 吸收光谱的计算结果表明, P替位Ti并不能增强TiO₂的可见光吸收能力, 但间隙P的存在大幅提高了TiO₂的可见光光吸收能力, 间隙P有可能是造成实验上P掺杂增强锐钛矿相TiO₂光催化活性的重要原因. 关键词： P掺杂 2')" href="#">锐钛矿相TiO₂ 第一性原理     

Preparation of TiO2 thin films from autoclaved sol containing needle-like anatase crystals

A new inorganic sol-gel method was introduced in this paper to prepare TiO₂ thin films. The autoclaved sol with needle-like anatase crystals was synthesized using titanyl sulfate (TiOSO₄) and peroxide (H₂O₂) as starting materials. The transparent anatase TiO₂ thin films were prepared on glass slides from the autoclaved sol by sol-gel dip-coating method. A wide range of techniques such as Fourier transform infrared transmission spectra (FT-IR), X-ray diffraction (XRD), thermogravimetry-differential thermal analysis (TG-DTA), scanning electron microscopes, X-ray photoelectron spectroscopy (XPS) and ultraviolet-visible spectrum were applied to characterize the autoclaved sol and TiO₂ thin films. The results indicate that the autoclaved sol is flavescent, semitransparent and stable at room temperature. The anatase crystals of TiO₂ films connect together to form net-like structure after calcined and the films become uniform with increasing heating temperature. The surface of the TiO₂ films contain not only Ti and O elements, but also a small amount of N and Na elements diffused from substrates during heat treatment. The TiO₂ films are transparent and their maximal light transmittances exceed 80% under visible light region.     

Assembly,characterization, and photocatalytic activities of TiO<Subscript>2</Subscript> nanotubes/CdS quantum dots nanocomposites

The semiconductor quantum dots (QDs) can be very efficient to tune the response of photocatalyst of TiO₂ to visible light. In this study, CdS QDs formed in situ with about 8 nm have been successfully deposited onto the surfaces of TiO₂ nanotubes (TNTs) to form TNTs/CdS QDs nanocomposites by use of a simple bifunctional organic linker, thiolactic acid. The diffuse reflectance spectroscopy (DRS) spectra of as prepared samples showed that the absorption edge of the TNTs/CdS composite is extended to visible range, with absorption edge at 530 nm. The photocatalytic activity and stability of TNTs/CdS were also evaluated for the photodegradation of rhodamine B. The results showed that when TNTs/CdS QDs was used, photocatalytic degradation of RhB under visible light irradiation reached 91.6%, higher than 45.4 and 30.5% for P25 and TNTs, respectively. This study indicated that the TNTs/CdS QDs nanocomposites were superior catalysts for photodegradation under visible light irradiation compared with TNTs and P25 samples, which may find wide application as a powerful photocatalyst in environmental field.     

Thickness effect of the TiO2 nanofiber scattering layer on the performance of the TiO2 nanoparticle/TiO2 nanofiber-structured dye-sensitized solar cells

TiO₂ nanofibers (NFs) were fabricated by an electrospinning process and were used as scattering layers in dye-sensitized solar cells (DSSCs). The NF-coated photoanodes of the DSSCs were prepared with a variety of scattering layer thicknesses. The thickness effect of the scattering layer on the double-layered TiO₂ nanoparticle (NP)/TiO₂ NF structure was investigated through structural, morphological, and optical measurements. In the double-layered photoanode, the TiO₂ NP layer plays a major role in dye adsorption and light transmission, and the TiO₂ NF scattering layer improves the absorption of visible light due to the light scattering effects. The scattering effect of TiO₂ NFs layer was examined by the incident monochromatic photon-to-electron conversion efficiency (IPCE) and UV–Vis spectrometry. The conversion efficiency for the 12 μm-thick photoanode composed of a 2 μm-thick TiO₂ NF layer and 10 μm-thick TiO₂ NP layer was higher than that of DSSCs with only TiO₂ NPs photoanode by approximately 33%.     

Preparation of visible light responsive N doped TiO2 via a reduction-nitridation procedure by nonthermal plasma treatment

A visible light responsive N-doped TiO₂ was prepared via a reduction-nitridation procedure by nonthermal plasma treatment. X-ray diffraction, N₂ adsorption, UV-vis spectroscopy, photoluminescence, and X-ray photoelectron spectroscopy were used to characterize the prepared TiO₂ samples. The plasma treatment did not change the phase composition and particle sizes of TiO₂ samples, but extended its absorption edges to the visible light region. The photocatalytic activities were tested in the degradation of an aqueous solution of a reactive dyestuff, methylene blue, under visible light. The photocatalytic activities of TiO₂ prepared by reduction-nitridation procedure were much higher than that of samples prepared by simple nitridation treatment. The enhanced activity was ascribed to the substitutional N-doping and appropriate concentration of oxygen vacancies. TOHN10 prepared by reduction-nitridation procedure exhibited excellent photocatalytic stability. A possible mechanism for the photocatalysis was proposed.