Relaxation behavior of poly(ethylene terephthalate)/poly(ethylene naphthalene 2,6‐dicarboxylate) blends prepared by cryogenic blending

A method including cryogenic grinding, melt pressing from the molten state, and quenching was used to prepare blends of poly(ethylene terephthalate) (PET) and poly(ethylene naphthalene 2,6‐dicarboxylate) (PEN) in which the two phases were highly dispersed. The effect of melt‐pressing times on the thermal properties and relaxation behavior of PET/PEN films were characterized with differential scanning calorimetry and dielectric spectroscopy. For short melt‐pressing times, two glass‐transition, two crystallization, and two melting peaks were observed, indicating the presence of PET‐rich and PEN‐rich phases in these blends. Longer melt‐pressing times revealed a single glass transition and a single α‐relaxation process, showing that PET–PEN block copolymers were likely to be formed during the melt pressing. The experimental findings were examined in terms of the transesterification reactions between the blend components, as revealed by ¹H NMR measurements. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2570–2578, 2002     

Synthesis,physical characterization,and acetone sorption kinetics in random copolymers of poly(ethylene terephthalate) and poly(ethylene 2,6-naphthalate)

Random copolymers of poly(ethylene terephthalate) (PET) and poly(ethylene 2,6-naphthalate) (PEN) were synthesized by melt condensation. In a series of thin, solvent cast films of varying PEN content, acetone diffusivity and solubility were determined at 35°C and an acetone pressure of 5.4 cm Hg. The kinetics of acetone sorption in the copolymer films are well described by a Fickian model. Both solubility and diffusivity decrease with increasing PEN content. The acetone diffusion coefficient decreases 93% from PET to PET/85PEN, a copolymer in which 85 weight percent of the dimethyl terephthalate in PET has been replace by dimethyl naphthalate 2,6-dicarboxylate. The acetone solubility coefficient in the amorphous regions of the polymer decreases by approximately a factor of two over the same composition range. The glass/rubber transition temperatures of these materials rise monotonically with increasing PEN content. Copolymers containing 20 to 80 wt % PEN are amorphous. Samples with <20% or >80% PEN contain measurable levels of crystallinity. Estimated fractional free volume in the amorphous regions of these samples is lower in the copolymers than in either of the homopolymers. Relative free volume as probed by positron annihilation lifetime spectroscopy (PALS) decreases systematically with increasing PEN content. Acetone diffusion coefficients correlate well with PALS results. Infrared spectroscopy suggests an increase in the fraction of ethylene glycol units in the trans conformation in the amorphous phase as the concentration of PEN in the copolymer increases. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2981–3000, 1998     

New colorless substrates based on polynorbornene‐chlorinated polyimide copolymers and their application for flexible displays

Novel polynorbornene (PNB)‐polyimide (PI) copolymers were synthesized based on poly(N‐phenyl‐exo‐norbornene‐5,6‐dicarboximide) (PPhNI) and chlorinated PI (BPDA/TCDB). Polynorbornene copolymers (PNCs) with diverse compositions of anhydride were synthesized via ring opening metathesis polymerization (ROMP) of N‐phenyl‐exo‐norbornene‐5,6‐dicarboximide (PhNI) and exo‐7‐oxanorbornene‐5,6‐dicarboxylic anhydride(exo‐NA), followed by copolymerization through a reaction with aromatic dianhydride (3,3′,4,4′‐biphenyltetra‐carboxylic dianhydride, BPDA) and tetrachlorinated diamine (2,2′,5,5′‐tetrachlorobenzidine, TCDB). The copolymer (PNIC) films exhibited good optical transparency with a transmittance of around 70% at 400 nm and a good thermal stability with a glass transition temperature at 276–300 °C. These flexible films also resisted most organic solvents and chemicals, such as methanol, acetone, tetrahydrofuran, N‐methylpyrrolidone, ethyl acetate, hydrochloric acid, sodium hydroxide, and hydrogen peroxide, etc. Indium tin oxide (ITO) coated thin films were prepared at various substrate deposition temperatures with a radio frequency (r.f.) planar magnetron sputtering system. The ITO thin films that were deposited onto the PNIC copolymer substrates had good electrical and optical properties. An organic light‐emitting device (OLED) was fabricated using the PNIC copolymer substrate with a structure of PNIC08/ ITO (anode)/hole‐transporting layer (HTL)/emitting & electron‐transporting layer (EM&ETL)/aluminum (cathode). The flexible OLED fabricated on the ITO‐grown PNIC substrate exhibited a performance that was comparable to corresponding ITO‐grown glass substrates. Therefore, the ITO‐grown PNIC substrate could possibly be a promising candidate as a substrate for flexible displays. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1806–1814, 2010     

Fast printing of thin,large area,ITO free electrochromics on flexible barrier foil

Processing of large area, indium tin oxide (ITO) free electrochromic (EC) devices has been carried out using roll‐to‐roll (R2R) processing. By use of very fine high‐conductive silver grids with a hexagonal structure, it is possible to achieve good transparency of the electrode covered substrates and when used in EC devices switching times are similar to corresponding ITO devices. This is obtained without the uneven switching of larger areas, which is generally observed when using ITO because of its high‐sheet resistance. The silver electrode structures for 18 × 18 cm² devices can be processed at high speed (10 m/min) on PET by flexographic printing and the EC polymer ECP‐Magenta as well as a minimal color changing polymer MCCP by slot‐die coating, showing the potential for fast fabrication of large volumes of low‐priced flexible EC devices by use of R2R processing techniques. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Transesterification kinetics of poly(ethylene terephthalate) and poly(ethylene 2,6‐naphthalate) blends with the addition of 2,2′‐bis(1,3‐oxazoline)

The kinetics of the transesterification reaction between poly(ethylene terephthalate) (PET) and poly(ethylene 2,6‐naphthalate) (PEN) with and without the addition of a chain extender were studied with ¹H NMR. Different kinetic approaches were considered, and a second‐order, reversible reaction was accepted for the PET/PEN reactive blend system. The addition of 2,2′‐bis(1,3‐oxazoline) (BOZ) promoted the transesterification reaction between PET and PEN in the molten state. The activation energy of the transesterification reaction for the PET/PEN reactive blend with BOZ (94.0 kJ/mol) was lower than that without BOZ (168.9KJ/mol). The rate constant k took an almost constant value for blend samples with different compositions mixed at 275 °C. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2607–2614, 2001     

Free volume and oxygen transport in cold‐drawn polyesters

Poly(ethylene terephthalate) (PET), poly(ethylene terephthalate‐co‐4,4′‐bibenzoate) (PETBB55), and poly(ethylene 2,6‐naphthalate) (PEN) were cold‐drawn to achieve uniform extension without crystallization or stress whitening, and oxygen transport properties were studied at temperatures from 10 to 40 °C. Correlation of oxygen solubility and polymer specific volume made it possible to consider the oriented polyester as a one‐phase densified glass. Orientation was viewed as decreasing the amount of excess‐hole free volume and bringing the nonequilibrium polymer glass closer to the equilibrium condition. Between 10 and 40 °C, the amount of excess‐hole free volume in PET decreased as the polymer approached the glass transition temperature. In contrast, temperature changes in this range had little effect on the excess‐hole free volume in PETBB55 and PEN, which were well below their glass transition temperature. Gas diffusion was viewed as discrete jumps of the oxygen molecule between holes of excess‐free volume. The jump length was extracted from the activation energy for diffusion according to a channel‐formation model. The result agreed well with the hole spacing estimated from a simple lattice model using the hole density reported in the literature. Extending the lattice model to estimate the mean excess‐free volume hole radius from the fractional free volume resulted in good correlation with the hole radius obtained from positron annihilation lifetime spectroscopy. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 493–504, 2004     

Conductivity,morphology, interfacial chemistry,and stability of poly(3,4‐ethylene dioxythiophene)–poly(styrene sulfonate): A photoelectron spectroscopy study

X‐ray photoelectron spectroscopy (XPS) has been used to characterize poly(3,4‐ethylene dioxythiophene)–poly(styrene sulfonate) (PEDT/PSS), one of the most common electrically conducting organic polymers. A correlation has been established between the composition, morphology, and polymerization mechanism, on the one hand, and the electric conductivity of PEDT/PSS, on the other hand. XPS has been used to identify interfacial reactions occurring at the polymer‐on‐ITO and polymer‐on‐glass interfaces, as well as chemical changes within the polymer blend induced by electrical stress and exposure to ultraviolet light. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2561–2583, 2003     

Lamellar‐level morphology induced by combined crystallization and liquid–liquid demixing in a poly(ethylene terephthalate)/poly(ethylene‐2,6‐naphthalate) blend

The lamellar‐level morphology of an extruded poly(ethylene terephthalate) (PET)/poly(ethylene‐2,6‐naphthalate) (PEN) blend was investigated with small‐angle X‐ray scattering (SAXS). Measurements were made as a function of the annealing time in the melt and the crystallization temperature. The characteristic morphological parameters at the lamellar level were determined by correlation function analysis of the SAXS data. At a low crystallization temperature of 120 °C, the increased amorphous layer thickness was identified in the blend, indicating that some PEN was incorporated into the interlamellar regions of PET during crystallization. The blend also showed a larger lamellar thickness than pure PET. A reason for the increase in the lamellar thickness might be that the formation of thinner lamellar stacks by secondary crystallization was significantly restricted because of the increased glass‐transition temperature. At high crystallization temperatures above 200 °C, the diffusion rates of noncrystallizable components were faster than the growth rates of crystals, with most of the noncrystallizable components escaping from the lamellar stacks. As a result, the blend showed an interfibrillar or interspherulitic morphology. © 2002 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 317–324, 2002     

Morphology and mechanical properties of blown films of a low‐density polyethylene/linear low‐density polyethylene blend

The morphologies of films blown from a low‐density polyethylene (LDPE), a linear low‐density polyethylene (LLDPE), and their blend have been characterized and compared using transmission electron microscopy, small‐angle X‐ray scattering, infrared dichroism, and thermal shrinkage techniques. The blending has a significant effect on film morphology. Under similar processing conditions, the LLDPE film has a relatively random crystal orientation. The film made from the LDPE/LLDPE blend possesses the highest degree of crystal orientation. However, the LDPE film has the greatest amorphous phase orientation. A mechanism is proposed to account for this unusual phenomenon. Cocrystallization between LDPE and LLDPE occurs in the blowing process of the LDPE and LLDPE blend. The structure–property relationship is also discussed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 507–518, 2002; DOI 10.1002/polb.10115     

Dielectric and conductivity processes in poly(ethylene terephthalate) and poly(ethylene naphthalate) homopolymers and copolymers

Electrical relaxation and conductivity processes in amorphous and semicrystalline poly(ethylene terephthalate) (PET) and poly(ethylene naphthalate) (PEN) homopolymers and certain PET/PEN copolymers have been studied by means of dielectric spectroscopy. Homopolymers and copolymers able to crystallize were subjected to successive thermal runs to investigate the influence of the thermal history upon the morphology and the electrical behavior of the polymeric systems. The morphology of the untreated as well as the heat‐treated specimens was determined by means of Differential Scanning Calorimetry (DSC). All samples exhibit β‐relaxation process, due to local motions of the C?O polar side groups, and α‐relaxation process associated to the glass/rubber transition. In the PEN spectrum an additional, subglass, mode was recorded, most probably attributed to cooperative motions of the naphthalene groups. Finally, the dynamic nature of the crystallization process is expressed via the over glass transition mode and the temperature dependence of dc conductivity recorded in amorphous PET, PEN, and PET/PEN (85/15) (wt/wt) samples. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3078–3092, 2006     

Quantitative analysis of near surfaces three‐dimensional orientation of polymer chains in PET and PEN films using polarized ATR FTIR spectroscopy

Polarized attenuated total reflection (ATR) Fourier transform infrared (FTIR) spectroscopy was utilized to characterize the three‐dimensional orientation of polymer chains near highly anisotropic surfaces generated by uniaxial drawing. A versatile method was proposed to analyze the molecular orientation of the polymers by combining the experimental refractive indices and optimized contact pressure by an anvil for solving the optical contact problem. This method is effective even when changes in the molecular orientation along the thickness direction caused by drawing are remarkable. In addition, this method enables quantitative comparison of the molecular orientation among different polymers in the same coordinate system. From the molecular orientation analysis of poly (ethylene terephthalate) (PET) and poly (ethylene naphthalate) (PEN), it was revealed that this method has a broader range of applications with high accuracy in estimating the molecular orientation of polymers compared with the conventional methods. The significant changes in the molecular orientation caused by uniaxial and biaxial drawing of PET and PEN films were quantitatively analyzed, and the reasons for the significant in‐plane orientation of PEN chains on the film plane are discussed. In addition, the difference in the molecular orientation between both sides of the films was also demonstrated. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 870–879, 2010     

Tear anisotropy in films blown from polyethylenes of different macromolecular architectures

Blown films of different types of polyethylenes, such as branched low‐density polyethylene (LDPE) and linear high‐density polyethylene (HDPE), are well known to tear easily along particular directions: along the film bubble's transverse direction for LDPE and along the machine direction (MD) for HDPE. Depending on the resin characteristics and processing conditions, different structures can form within the film; it is therefore difficult to separate the effects of the crystal structure and orientation on the film tear behavior from the effects of the macromolecular architecture, such as the molecular weight distribution and long‐chain branching. Here we examine LDPE, HDPE, and linear low‐density polyethylene (LLDPE) blown films with similar crystal orientations, as verified by through‐film X‐ray scattering measurements. With these common orientations, LDPE and HDPE films still follow the usual preferred tear directions, whereas LLDPE tears isotropically despite an oriented crystal structure. These differences are attributed to the number densities of the tie molecules, especially along MD, which are considerably greater for linear‐architecture polymers with a substantial fraction of long chains, capable of significant extension in flow. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 413–420, 2005     

Electrically conductive,melt‐processed ternary blends of polyaniline/dodecylbenzene sulfonic acid,ethylene/vinyl acetate,and low‐density polyethylene

Although polyaniline (PANI) has high conductivity and relatively good environmental and thermal stability and is easily synthesized, the intractability of this intrinsically conducting polymer with a melting procedure prevents extensive applications. This work was designed to process PANI with a melting blend method with current thermoplastic polymers. PANI in an emeraldine base form was plasticized and doped with dodecylbenzene sulfonic acid (DBSA) to prepare a conductive complex (PANI–DBSA). PANI–DBSA, low‐density polyethylene (LDPE), and an ethylene/vinyl acetate copolymer (EVA) were blended in a twin‐rotor mixer. The blending procedure was monitored, including the changes in the temperature, torque moment, and work. As expected, the conductivity of ternary PANI–DBSA/LDPE/EVA was higher by one order of magnitude than that of binary PANI–DBSA/LDPE, and this was attributed to the PANI–DBSA phase being preferentially located in the EVA phase. An investigation of the morphology of the polymer blends with high‐resolution optical microscopy indicated that PANI–DBSA formed a conducting network at a high concentration of PANI–DBSA. The thermal and crystalline properties of the polymer blends were measured with differential scanning calorimetry. The mechanical properties were also measured. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3750–3758, 2004     

Origin of directional tear in blown films of ethylene/methacrylic acid copolymers and ionomers

Blown films of ethylene/methacrylic acid copolymers and ionomers can exhibit pronounced directional tear, meaning that a tear can propagate with much less resistance in a particular direction. However, films blown from the same resin can exhibit different preferred tear directions, which depend on the process conditions. Through wide‐ and small‐angle X‐ray scattering, we demonstrate that this directional tear behavior is a direct result of the orientation of the lamellar polyethylene crystallites in these films; tears propagate more readily between lamellae than through lamellae, as previously recognized for low‐density polyethylene homopolymer. Unlike polyethylene homopolymer, however, an increase in the blowup ratio during the film processing of ethylene/methacrylic acid copolymers and ionomers leads to a 90° rotation of the lamellae that form upon subsequent crystallization. The lamellar rotation arises from a change in the orientation of the row nuclei that form after the melt is inflated and produces a consequent rotation of the preferred tear direction. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 97–106, 2005     

Syntheses and characterization of functionalized polynorbornene dicarboximides for flexible substrates

In this study, we synthesized polynorbornene (PNB) dicarboximides substituted by monochlorophenyl group (PMCPhNDI) and dichlorophenyl group (PDCPhNDI) via ring‐opening polymerization using a ruthenium catalyst and investigated their thermal, mechanical, and optical properties. We also discussed the performance and application of the functionalized PNB dicarboximide films as flexible substrates for organic light‐emitting devices (OLEDs). The polymer films exhibited good optical transparency with an average transmittance of around 97% in the visible light region and good thermal stability with a 5% degradation temperature of >440°C. The polymers were applied for flexible displays, which were coated on indium tin oxide (ITO) thin films using a radio‐frequency planar magnetron sputtering system with changing the deposition substrate temperatures. A flexible OLED that was fabricated on the ITO‐grown polymer substrates exhibited a performance as comparable to the corresponding ITO‐grown glass substrates. Copyright © 2012 John Wiley & Sons, Ltd.     

不同导电基底对TiO2薄膜光致亲水性的影响

分别在导电铝合金片(Al)和具有阳极氧化铝层的非导电铝片(AAO/Al), 以及铟锡氧化物导电玻璃(ITO/glass)和普通非导电玻璃(glass)表面通过提拉法制备出TiO2/Al和TiO2/AAO/Al, 以及TiO2/ITO/glass和TiO2/glass两组TiO2薄膜样品, 通过测试紫外光照下水滴接触角的变化考察TiO2薄膜的光致亲水性. 结果表明, 相对于TiO2/Al2O3/Al, 基底导电的TiO2/Al表现出较好的光致亲水性能; 而相对于TiO2/glass, 基底导电的TiO2/ITO/glass表现出较差的光致亲水性能. 分析认为, Al和ITO两导电基底和TiO2薄膜间的不同电子转移方向影响TiO2薄膜的光致亲水性能, Al片提供电子给TiO2有助于提高以光生电子为主要初级活性物种的光致亲水性, 而ITO接受TiO2的光生电子, 导致光致亲水性的下降.     

White light electroluminescence from graphene‐enhanced single polymer comprising two color emitters of equal molar ratios

White polymeric light‐emitting diode (WPLED) based on a single polymer, poly(3‐hexylthiophene‐alt‐9,9‐dioctylfluorene) (PTAF), has been successfully demonstrated. This conjugated alternating copolymer, PTAF, comprises 50 mol % of 3‐hexylthiophene which is an orange‐red color chromophore and 50 mol % 9,9‐dioctylfluorene which is a bluish‐green color chromophore. It was synthesized by Suzuki cross‐coupling reaction and has a molecular weight of 15,021 and polydispersity of 1.36. Nanocomposite consisting PTAF and graphene nanosheets enhances the optoelectronic properties and the device fabricated with a configuration of ITO/PEDOT:PSS/(PTAF + 1% graphene)/Ca/Al shows two‐color white electroluminescence with CIE 1931 coordinates of (0.28, 0.34). The white luminescence from a single polymer affords the WPLED device a simple structure and low fabrication cost. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Enhanced super-hydrophobic and switching behavior of ZnO nanostructured surfaces prepared by simple solution--immersion successive ionic layer adsorption and reaction process

A simple and cost-effective successive ionic layer adsorption and reaction (SILAR) method was adopted to fabricate hydrophobic ZnO nanostructured surfaces on transparent indium-tin oxide (ITO), glass and polyethylene terephthalate (PET) substrates. ZnO films deposited on different substrates show hierarchical structures like spindle, flower and spherical shape with diameters ranging from 30 to 300 nm. The photo-induced switching behaviors of ZnO film surfaces between hydrophobic and hydrophilic states were examined by water contact angle and X-ray photoelectron spectroscopy (XPS) analysis. ZnO nanostructured films had contact angles of ~140° and 160°±2 on glass and PET substrates, respectively, exhibiting hydrophobic behavior without any surface modification or treatment. Upon exposure to ultraviolet (UV) illumination, the films showed hydrophilic behavior (contact angle: 15°±2), which upon low thermal stimuli revert back to its original hydrophobic nature. Such reversible and repeatable switching behaviors were observed upon cyclical exposure to ultraviolet radiation. These biomimetic ZnO surfaces exhibit good anti-reflective properties with lower reflectance of 9% for PET substrates. Thus, the present work is significant in terms of its potential application in switching devices, solar coatings and self-cleaning smart windows.     

UV grafting of methacrylic acid and acrylic acid on high‐density polyethylene in different solvents and the wettability of grafted high‐density polyethylene. II. Wettability

The wettability of high‐density polyethylene grafted with methacrylic acid is strongly influenced by the nature of the grafting solvent. Here, the wettability is expressed by the water contact angle and absorbency. The initial (10‐s) contact angle of polyethylene (PE) grafted in acetone/water solution decreased rapidly with the extent of grafting at low grafting levels and then remained independent of the grafting level at about 50°. When a water droplet was left on the surface for a longer time, its contact angle decreased to a very low value in the period of about 10 min. For the PE samples grafted in dichloromethane, petroleum ether, cyclohexane, and chloroform, there was only a small decrease (10°) in the contact angle of water from that observed on pure PE, even when the extent of grafting was very large. The PE films grafted in these organic solvents also took a much longer time than PE films grafted in acetone/ water solution to obtain equilibrium water absorbency. The water absorbency of PE films grafted in 30% acetone/water solution was about twice that of PE films grafted in the other solvents at the same extent of grafting. These results suggested that for the solvents other than acetone/water, the grafted layer is partially buried below the surface of PE. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 263–270, 2004     

Synthesis and electro‐optical properties of light‐emitting polymers containing oxadiazole derivatives for light‐emitting diodes applications

Two PPV‐based bipolar polymers containing 1,3,4‐oxadiazole pendant groups were synthesized via the Gilch polymerization reaction for use in light‐emitting diodes (LEDs). The resulting polymers were characterized using ¹H and ¹³C NMR, elemental analysis, DSC, and TGA. These polymers were found to be soluble in common organic solvents and are easily spin‐coated onto glass substrates, producing high optical quality thin films without defects. The electro‐optical properties of ITO/PEDOT/polymer/Al devices based on these polymers were investigated using UV‐visible, PL, and EL spectroscopy. The turn‐on voltages of the OC₁Oxa‐PPV and OC₁₀Oxa‐PPV devices were found to be 8.0 V. The maximum brightness and luminescence efficiency of the OC₁Oxa‐PPV device were found to be 544 cd/m² at 19 V and 0.15 cd/A, respectively. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1098–1110, 2008