Pyrolysis products and thermal degradation mechanism of intrinsically flame-retardant calcium alginate fibre

Intrinsically flame-retardant calcium alginate fibre was prepared by wet spinning and its pyrolysis products and thermal degradation mechanism studied. Combustion behaviour and flammability were assessed using the limiting oxygen index (LOI) and cone calorimetry. LOI results showed that calcium alginate fibre was intrinsically flame retardant with LOI value of 48.0, as compared to about 20.0 for viscose fibre. Cone calorimetry indicated that heat release rate and total heat release values of intrinsically flame-retardant fibre were significantly less than those of viscose fibre. It also shown that intrinsically flame-retardant fibre combustion produced greater quantities of residues than did viscose fibre combustion. Combustion residues were examined using scanning electron microscopy, indicating that calcium alginate fibre produced consistent, thick residue crusts. Pyrolysis was investigated using pyrolysis-gas chromatography-mass spectrometry (Py-GC-MS) which showed that cracking products produced from calcium alginate fibres combustion were less than those in viscose fibre combustion, and pyrolysis of the intrinsically flame-retardant fibre was incomplete. Thermogravimetric analysis (TG) indicated that calcium alginate fibre generated more residues containing carbonaceous char and calcium carbonate, as compared with viscose fibre. We propose a condensed phase mechanism for the calcium alginate fibre flame-retardancy effect.     

Incorporation of a flame retardancy enhancing phosphorus-containing diol into poly(butylene terephthalate) via solid state polycondensation: A comparative study

The phosphorus-containing aliphatic-aromatic diol 2-[4-(2-hydroxy-ethoxy)-3-(10-oxo-10-H9-oxa-10-λ5-phospha-phenanthrene-10-yl)-phenoxy]-ethanol, a potential flame retardant, was incorporated into poly(butylene terephthalate) (PBT) by solid state polycondensation. Thus, polymers with various ratios of PBT/DOPO-diol and number-average molar masses up to 57,000 g mol⁻¹ could be prepared. Their molar masses were higher than those of copolyesters with comparable composition obtained by direct melt polycondensation. Structures and properties of copolyesters produced by both methods were not significantly different after melt processing. Their thermal properties and combustion behaviour were investigated by means of DSC, TGA, and pyrolysis combustion flow calorimetry. Combustion studies revealed high char yields, very low heat release capacities and high limiting oxygen index (LOI) at rather low P-contents, indicative of better flame-retardancy properties.     

Fire retarded polyurethane foam composites based on steel slag/ammonium polyphosphate system: A novel strategy for utilization of metallurgical solid waste

A series of FR-RPUF composites were prepared by a one-step water foaming process with ammonium polyphosphate (APP) and steel slag (SS) as flame retardants. Thermogravimetric analysis (TG), limiting oxygen index (LOI), UL-94 vertical combustion test, microscale combustion calorimetry (MCC), TG-Fourier transform infrared spectrometry (TG-FTIR), scanning electron microscopy (SEM), Raman spectra and FTIR were used to investigate the thermal stability, flame retardancy, combustion performance, gas phase products, and char residue morphology of FR-RPUF composites. TG test results showed that the initial decomposition temperature (T_-5wt%) and char residue rate at 700°C of RPUF/APP/SS composites were significantly enhanced by the addition of APP and SS, and the thermal stability of the composites was improved. Flame retardant test results confirmed the significantly increased LOI values of RPUF/APP/SS composites with V-0 rating. TG-FTIR also confirmed the obviously decreased release of toxic gases and flammable gases in the combustion of RPUF/APP/SS composites. SEM and Raman spectra of char residues for the composites suggested that APP/SS system improved the compactness and graphitization degree of char layer for RPUF/APP/SS composite. The above researches provide a new strategy for the utilization of SS in fire safety engineering.     

Synergistic effects of zeolites on a novel intumescent flame-retardant low-density polyethylene (LDPE) system

A char forming agent and silica-gel microencapsulated APP were selected to form novel intumescent flame-retardant system (IFR) to prepare flame-retardant low-density polyethylene (LDPE) composites, and then the influence of zeolites on the thermal and flame-retardant properties of flame-retardant LDPE composites were studied. With the addition of 1 wt% zeolites to LDPE/IFR system, the LOI value increases from 29.0 to 34.0 %. The results of cone calorimetry show that the heat release rate peak and total heat release of the intumescent flame-retardant LDPE composite with 1 wt% zeolites decreases remarkably compared with that of without zeolites. The scanning electron microscopy indicates zeolites with suitable content can improve the quality of the char layer of flame-retardant LDPE composite which is more coherent and dense. The zeolites with the appropriate content can remarkably improve the flame-retardant properties of the LDPE composites.     

Investigation on the thermal decomposition and flame retardancy of wood treated with a series of molybdates by TG–MS

A flame-retardant wood was prepared using a series of insoluble molybdates through the double bath technique. The flame retardancy of the wood samples was studied with the limiting oxygen index (LOI) method. The relationships between the flame-retardant performance and the thermal property of wood were studied by the thermogravimetry (TG), derivative thermogravimetry (DTG), differential thermal analysis (DTA), scanning electron microscopy (SEM), and the thermogravimetry–mass spectrometry (TG–MS) analysis methods. The results showed that the insoluble molybdates, which were precipitated into the wood by the double bath technique, can obviously improve the flame retardancy of wood. Similarly, the transition metal molybdates showed higher flame-retardant efficiency than the main group metal molybdates do, which probably due to the thermal barrier effect that Fe₂(MoO₄)₃ acts during the combustion of the samples. At the same time, Fe₂(MoO₄)₃ catalyzed the dehydration and carbonization reactions of wood, and caused an increase in the amount of char produced, and an improvement of the stability of the char residue. Moreover, the mass spectrometry results indicated that the excess transition metal ions speed up the deep decomposition of the char residue, and resulting in the smoldering of wood.     

Study of nanocarbon black as synergist on improving flame retardancy of ethylene-vinyl acetate/brucite composites

Nanocarbon black (CB) was introduced into ethylene-vinyl acetate/brucite (EM) composites to investigate the synergistic effect of CB and metal hydroxide on improving the flame retardancy of EVA. Flammability properties of the as-prepared EVA composites were investigated by thermogravimetric analysis, limiting oxygen index (LOI), UL-94 test and cone calorimetry test. The results indicated that the optimum mass ratio of CB/brucite was 1/54, at which the EVA composites displayed dramatic improvement on thermal stability and flame retardancy. The LOI value was as high as 35.3%, the UL-94 passed the V-0 rating, and the peak heat release rate reduced 79% in comparison with pure EVA. Based on the morphology and structure analysis for residue chars, the flame-retardant mechanism was attributed mainly to the positive synergistic effect of CB and brucite on promoting the formation of better carbon protective layer during combustion.

     

Evaluation of physico-chemical properties and antimicrobial synergic effect of ceftazidime-modified chitosan

The aim of this work was to study the effect of tris(3-nitrophenyl) phosphine (NPPh3), which showed a good thermal stability and carbon-forming ability, on the flame retardancy and thermal degradation mechanism of epoxy resins. A series of diglycidyl ether of bisphenol A (DGEBA) loaded with tris(3-nitrophenyl) phosphine (NPPh3) were prepared. It was found that NPPh3 can effectively improve the flame retardancy and thermal stability of the composites. When the loading amount of NPPh3 was 14%, the LOI value of the DGEBA composites was 29.2% (about 1.53 times the corresponding value of the original DGEBA resin). Thermal stability was studied by thermogravimetric analysis, and the results showed that the addition of NPPh3 can improve char formation of this system both in nitrogen and in air atmosphere. Specifically, its combustion residue at 800 °C in nitrogen atmosphere was about 4.26 times of the original resin. Differential scanning calorimetry indicated that NPPh3 slightly decreased the glass transition temperature of epoxy resins. Additionally, the gaseous degradation products were analyzed by thermogravimetric analysis/infrared spectrometry, providing insight into the thermal degradation mechanism. Scanning electron microscopy and Fourier transform infrared were brought together to evaluate the morphology and structure of the residual char obtained after combustion.     

Combustion behavior and thermal stability of ethylene-vinyl acetate composites based on CaCO3-containing oil sludge and carbon black

CaCO₃-containing oil sludge (OS) is a by-product from petroleum industry, with great amount of production. Therefore, an effective processing methods for CaCO₃-containing OS is urgently needed. Herein, ethylene-vinyl acetate (EVA) composites based on CaCO₃-containing OS and carbon black (CB) were prepared by melt blending method. The combustion behavior and thermal stability of flame-retardant EVA/OS/CB composites were investigated by cone calorimeter test, limiting oxygen index (LOI), scanning electron microscopy (SEM), smoke density test (SDT), and thermogravimetry-Fourier infrared spectrometry. The heat release rate and smoke production rate of the ternary composites containing 3% CB significantly decreased compared with the EVA/OS composites and pure EVA. Moreover, addition of a certain amount of CB could evidently increase LOI values. The morphologies and structures of the residues, revealed by SEM, ascertained that a better carbonaceous protective layer was formed on the ternary composites than the EVA/OS composite. It was obtained from SDT that CB in the material could retard the smoke production with the application of the pilot flame. The EVA/OS/CB composites assumed a higher thermal stability than the EVA/OS composites and pure EVA.

     

Flame retardant properties and mechanism of an efficient intumescent flame retardant PLA composites

The charring agent (CNCA‐DA) containing triazine and benzene rings was combined with ammonium polyphosphate (APP) to form intumescent flame retardant (IFR), and it was occupied to modify polylactide (PLA). The flame retardant properties and mechanism of flame retardant PLA composites were investigated by the limited oxygen index (LOI), vertical burning test (UL‐94), thermogravimetric analysis, microscale combustion calorimetry, scanning electron microscopy, laser Raman spectroscopy analysis and X‐ray photoelectron spectroscopy. The analysis from LOI and UL‐94 presented that the IFR was very effective in flame retardancy of PLA. When the weight ratio of APP to CNCA‐DA was 3:1, and the IFR loading was 30%, the IFR showed the best effect, and the LOI value reached 45.6%. It was found that when 20 wt% IFR was loaded, the flame retardancy of PLA/IFR still passed UL‐94 V‐0 rating, and its LOI value reached 32.8%. The microscale combustion calorimetry results showed that PLA/IFR had lower heat release rate, total heat release, and heat release capacity than other composites, and there was an obvious synergistic effect between APP and CNCA‐DA for PLA. IFR containing APP/CNCA‐DA had good thermal stability and char‐forming ability with the char residue 29.3% at 800°C under N₂ atmosphere. Scanning electron microscopy observation further indicated that IFR could promote forming continuous and compact intumescent char layer. The laser Raman spectroscopy analysis and X‐ray photoelectron spectroscopy analysis results indicated that an appropriate graphitization degree of the residue char was formed, and more O and N were remained to form more cross‐linking structure. Copyright © 2016 John Wiley & Sons, Ltd.     

Synthesis of organo-modified α-zirconium phosphate and its effect on the flame retardancy of IFR poly(lactic acid) systems

Novel intumescent flame-retardant poly(lactic acid) (PLA/IFR)/organo-modified α-zirconium phosphate(OZrP) nanocomposites were prepared via incorporation of charring agent (CA), ammonium polyphosphate (APP) and OZrP into PLA. OZrP was synthesized directly by a solvent thermal method. The morphological characterization of PLA/IFR/OZrP nanocomposites was conducted by wide angle X-ray diffraction (WXRD) and transmission electron microscopy (TEM). The effect of the OZrP on flame retardancy and the thermal stability of PLA/IFR composites were studied by thermogravimetric analysis (TGA), limiting oxygen index (LOI), vertical burning test (UL-94) and cone calorimeter test. The TGA data illustrated that the OZrP could increase the residue and significantly improve the flame retardancy of PLA/IFR/OZrP nanocomposites showing an excellent synergistic effect. The addition of OZrP to the flame-retardant PLA increases the LOI and enhances the UL-94 rating. Cone calorimeter tests gave clear evidence that the incorporation of OZrP into PLA/IFR composites resulted in the significant reduction of the heat release rate (HRR), low total heat release (THR) and high amount of char residues during combustion. The flame-retardant mechanism of PLA/IFR/OZrP nanocomposites may correspond to the intumescent flame-retardant mechanism and catalyzed carbonization mechanism caused by OZrP.     

Influence of the structural characteristic of pyrolysis products on thermal stability of styrene-butadiene rubber composites reinforced by different particle sized kaolinites

A series of rubber composites were prepared by blending styrene-butadiene rubber (SBR) latex and the different particle sized kaolinites. The thermal stabilities of the rubber composites were characterized using thermogravimetry, digital photography, scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy, and Raman spectroscopy. Kaolinite SBR composites showed much greater thermal stability when compared with that of the pure SBR. With the increase of kaolinite particle size, the pyrolysis products became much looser; the char layer and crystalline carbon content gradually decreased in the pyrolysis residues. The pyrolysis residues of the SBR composites filled with the different particle sized kaolinites showed some remarkable changes in structural characteristics. The increase of kaolinite particle size was not beneficial to form the compact and stable crystalline carbon in the pyrolysis process, and resulted in a negative influence in improving the thermal stability of kaolinite/SBR composites.     

An efficient halogen-free flame retardant for glass-fibre-reinforced poly(butylene terephthalate)

Compared with poly(butylene terephthalate) (PBT), glass-fibre-reinforced poly(butylene terephthalate) (GF-PBT) is difficult to flame retard with halogen-free flame retardants. In the present study, the aluminium salt of hypophosphorous acid (AP) was used as a flame retardant for GF-PBT. A series of flame-retardant GF-PBT composites was prepared via melt compounding. The flame retardance and combustion behaviour of the composites were studied by limiting oxygen index (LOI), vertical burning test (UL-94) and cone calorimetric test. Thermal behaviours and thermal decomposition kinetics were investigated by thermogravimetric analysis (TGA) under N₂ atmosphere. The addition of AP to the composites could result in an increased LOI value, a UL-94 V-0 (1.6 mm) classification and a better fire performance in cone calorimetric tests. The char morphology observation after flame-retardant tests, calculation of decomposition kinetics, X-ray photoelectron spectroscopy (XPS) and infra-red spectral analysis of the char residue confirmed the condensed-phase flame-retardant mechanism. Furthermore, the mechanical properties of the flame-retardant composites were not deteriorated, retaining an acceptable level.     

Preparation,flame retardancy,and thermal degradation of epoxy thermosets modified with phosphorous/nitrogen‐containing glycidyl derivative

Phosphorus/nitrogen‐containing advanced epoxy resins were obtained by chain‐extension of the diglycidyl ether of bisphenol‐A epoxy (DGEBA) resin with phosphorus‐modified triglycidyl isocyanurate (TGICP). The structure of TGICP was characterized by Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance (NMR). Differential scanning calorimetry revealed that the EP/TGICP composites possessed higher glass transition temperatures than that of phosphorus free EP. The thermal stability and flame retardant properties of the epoxy resin/TGICP systems were investigated by thermogravimetric analysis (TGA), limiting oxygen index (LOI), and vertical burning test (UL‐94) test. When the TGICP content was 10 wt%, the LOI value of epoxy resin system was as high as 35.0% and it can obtain the V‐0 grade in UL‐94 protocol. From microscale combustion calorimetry (MCC) measurement, it was found that the addition of TGICP reduced the value of peak heat release rate and total heat release. The thermal degradation process of EP and EP/TGICP composite was monitored by real time FTIR. Moreover, scanning electron microscopy (SEM) and X‐ray photoelectron spectroscopy (XPS) were used to explore the morphology and chemical components of the char residues. Copyright © 2010 John Wiley & Sons, Ltd.     

六苯氧基环三磷腈的热解及其对环氧树脂的阻燃机理

采用极限氧指数仪和锥形量热仪测试了以六苯氧基环三磷腈(HPCP)阻燃环氧树脂的燃烧性能,结果显示,与纯环氧树脂相比,阻燃环氧树脂的极限氧指数值(LOI)明显提高、热释放速率峰值(pk-HRR)和总热释放量(THR)明显下降、环氧树脂的点燃时间提前以及分解速度加快.采用热失重(TGA)、热重红外联用(TGA-FTIR)、X射线光电子能谱(XPS)和热裂解气相色谱质谱联用(Py-GC/MS)研究了HPCP及其阻燃环氧树脂的热解路线和阻燃机理.结果表明,在阻燃环氧树脂过程中,一方面,HPCP分子中的苯氧基团首先解离并发生歧化反应,由此产生的苯氧基及其歧化产物的焠灭效应在环氧树脂中发挥气相阻燃作用,剩余的磷腈环和苯环基团会进一步裂解产生小分子碎片;另一方面,环氧树脂基体在HPCP的作用下提前分解,产生了基于双酚A结构的大分子碎片并在HPCP裂解产物作用下加速炭化,从而使更多的基体组分以残炭的形式被固定在凝聚相中,提高了阻燃环氧树脂的残炭产率,发挥了凝聚相阻燃作用.     

Microencapsulation of bisphenol-A bis (diphenyl phosphate) and influence of particle loading on thermal and fire properties of polypropylene and polyethylene terephtalate

Microencapsulated flame retardant, bisphenol-A bis (diphenyl phosphate) (BDP), with a silane shell was prepared by sol–gel process with the goal of incorporating them in polymeric matrices by melt blending to improve the flame retardancy of isotactic polypropylene (iPP) and polyethylene terephtalate (PET). The influence of the loading content on thermal transitions has been studied by differential scanning calorimetry (DSC), the thermal stability of the polymer/microcapsules composites has been assessed by thermogravimetric analysis (TGA) and cone calorimetry has been used to study the fire reaction. It was noticed that the microcapsules have a limited influence on the thermal transitions of iPP matrix, but a decrease of the melting and glass transition temperatures was detected for the PET microcomposites. TGA results showed that the addition of microcapsules could improve char formation of the PET systems both in nitrogen and in air atmospheres, whereas only a small improvement of the thermal stability was detected in oxidative atmosphere for the iPP samples. Furthermore, cone calorimeter experiments show that the incorporation of microcapsules in the iPP gives almost no improvement in the iPP fire reaction. However, the microcapsules act as flame retardant in PET reducing the heat release rate during the combustion and the total heat evolved. Therefore, microcapsules can act as a char promoter agent to enhance the fire resistance in the case of PET.     

Evaluation of activation energy conformity derived from model-free non-isothermal predictions and Arrhenius isothermal results

Organically modified montmorillonite (OMMT) was used as synergist to enhance the flame-retardant and mechanical properties of poly(butylene succinate)/intumescent flame retardant (PBS/IFR) composites. The flame-retardant, thermal degradation and combustion properties of PBS and its flame-retardant composites were characterized by limiting oxygen index (LOI) test, vertical burning (UL-94) test, thermogravimetric analysis, cone calorimeter and scanning electron microscopy, respectively. The results indicate that PBS/IFR composites exhibit excellent flame retardance when OMMT is at an appropriate content. PBS/IFR composite with 20 wt% IFR and 1.5 wt% OMMT has an LOI of 40.1% and can pass the UL-94 V0 rating. The synergistic effect between OMMT and IFR on the flame-retardant properties of PBS depends on the content of OMMT, and excessive OMMT diminish this synergistic effect. The possible flame-retardant mechanism of OMMT on PBS/IFR composite is proposed. The results of mechanical test also indicate that OMMT can effectively increase the notched impact strength of PBS/IFR composites.     

A novel flame retardant containing phosphorus,nitrogen, and sulfur

In this article, a novel intumescent flame retardant (IFR) PNSFR containing three flame-retardant elements, phosphorus, nitrogen, and sulfur was designed and synthesized. Then a series of flame-retardant thermoplastic polyurethanes (TPU) were prepared using the PNSFR. The effects of the flame retardant on the flammability of TPU/PNSFR composites were investigated by limited oxygen index (LOI) and UL-94 vertical burning. The results showed that TPU containing 10 mass% PNSFR had the highest LOI value (36) and could reach the V-0 rating. The flame-retardant mechanism of PNSFR in TPU was also disclosed using thermogravimetric analysis (TG), scanning electron micrograph, TG-infared spectrometry, and Fourier transform infrared spectroscopy. The sulfur and phosphorus elements of PNSFR can be kept in residual char. Moreover, an optimal loading amount of the IFR in TPU is in favor of forming dense and continuous char layer to prevent heat transfer and the spread of flammable gases. The IFR PNSFR may find potential use for various flame-retardant polyurethanes.     

Co-flame retarding effect of ethanolamine modified titanium-containing polyhedral oligomeric silsesquioxanes in epoxy resin

A metal-doped organic and inorganic hybrid polyhedral oligomeric silsesquioxanes (POSS) with a titanium atom in the POSS cage and an ethanolamine substitute group in the corner, namely MEA-Ti-POSS, was synthesized through simple condensation reaction and substitute reaction. It was blended with 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) to form a kind of blending-type flame retardant system for the modification of epoxy resins. The thermal stability, flame retardancy and mechanical properties of cured epoxy resin composites were studied. Comparing with pure epoxy resin, the LOI value of EP/MEA-Ti-POSS/DOPO composites was raised from 25.2% to 32.7%, and the UL-94 grade reached V-0 level at a loading of the mixture of 5% MEA-Ti-POSS and 5% DOPO. In addition, the cone calorimetry results showed that the heat release rate, total heat release and total smoke production as well as smoke production rate were all reduced during the combustion of EP/MEA-Ti-POSS/DOPO composites. The residual char analysis revealed that carbon residues of EP/MEA-Ti-POSS/DOPO composite served as a physical protective layer to insulate the oxygen and combustible gases to reduce the ablation of the matrix. It was concluded that the mixture of MEA-Ti-POSS and DOPO not only effectively raised the thermal stability and flame retardancy of epoxy composited materials, but also improved their mechanical properties, which expanded a promising application of the metal-POSS derivatives as non-halogen additives in the flame retardant polymers.     

STUDY ON THE EFFECTS OF TLCP ON PYROLYSIS OF PET AND ITS RETARDANT MECHANISM

The flame retardancy of aromatic thermotropic liquid crystal phosphorus-containing copolyester,TLCP,on PET was investigated.The results show that the presence of TLCP promotes char formation of the substrate and enhances thermal stability of char,hence delay its decomposition.SEM pictures show that the char formed from PET/TLCP is more compact, therefore is more resistant to fire and heat than that from pure PET.Evolved gas analysis by I.R measurements indicates that TLCP would decompose to produce phosp...     

Synthesis of a novel polyphosphazene/triazine bi‐group flame retardant in situ doping nano zinc oxide and its application in poly (lactic acid) resin

A novel polyphosphazene/triazine bi‐group flame retardant in situ doping nano ZnO (A4‐d‐ZnO) was synthesized and applied in poly (lactic acid) (PLA). Fourier transform infrared (FTIR), solid state nuclear magnetic resonance (SSNMR), X‐ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM), transmission electron microscope (TEM), and energy dispersive spectrometer (EDS) were used to confirm the chemical structure of A4‐d‐ZnO. The thermal stability and the flame‐retardant properties of the PLA composites were characterized by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), limiting oxygen index (LOI), vertical burning test (UL‐94), and micro combustion calorimeter (MCC) test. The results of XPS showed that A4‐d‐ZnO has been synthesized, and the doping ratio of ZnO was 7.2% in flame‐retardant A4‐d‐ZnO. TGA results revealed that A4‐d‐ZnO had good char forming ability (40 wt% at 600°C). The results of LOI, vertical burning test, and MCC showed that PLA/5%A4‐d‐ZnO composite acquired a higher LOI value (24%), higher UL94 rating, and lower pk‐HRR (501 kW/m²) comparing with that of pure PLA. It indicated that a small amount of flame‐retardant A4‐d‐ZnO could achieve great flame‐retardant performance in PLA composites. The catalytic chain scission effect of A4‐d‐ZnO could make PLA composites drip with flame and go out during combustion, which was the reason for the good flame‐retardant property. Moreover, after the addition of A4‐d‐ZnO, the impaired mechanical properties of PLA composites are minimal enough.