Au/α-Fe2O3 催化剂存贮失活环境因素及机理分析

 采用沉积沉淀法制备了 CO 低温氧化催化剂 Au/α-Fe₂O₃, 通过 X 射线衍射、X 射线光电子能谱、N₂ 吸附-脱附、傅里叶变换红外光谱、H₂ 程序升温还原和 CO₂ 程序升温脱附等手段对催化剂进行了表征, 探讨了在室温大气气氛下光线照射以及表面吸附等环境因素所导致的催化剂存贮失活及其作用机理. 结果表明, 经 110 ^oC 干燥的 Au/α-Fe₂O₃催化剂表面同时存在 Au³⁺和 Au^δ+ (0 ≤ δ ≤ 1) 物种, 且前者催化 CO 氧化的活性更高; 在室温大气气氛下, 紫外线照射会引起 Au³⁺的还原和 Au 颗粒的生长, 导致催化剂的不可逆失活. 此外, 空气中的 H₂O 和 CO₂ 可同时吸附在 α-Fe₂O₃的表面, 形成表面碳酸盐物种, 会引起催化剂的可逆失活.     

Bipyridine‐Assisted Assembly of Au Nanoparticles on Cu Nanowires To Enhance the Electrochemical Reduction of CO2

We report a new strategy to prepare a composite catalyst for highly efficient electrochemical CO₂ reduction reaction (CO₂RR). The composite catalyst is made by anchoring Au nanoparticles on Cu nanowires via 4,4′‐bipyridine (bipy). The Au‐bipy‐Cu composite catalyzes the CO₂RR in 0.1 m KHCO₃ with a total Faradaic efficiency (FE) reaching 90.6 % at ?0.9 V to provide C‐products, among which CH₃CHO (25 % FE) dominates the liquid product (HCOO^?, CH₃CHO, and CH₃COO^?) distribution (75 %). The enhanced CO₂RR catalysis demonstrated by Au‐bipy‐Cu originates from its synergistic Au (CO₂ to CO) and Cu (CO to C‐products) catalysis which is further promoted by bipy. The Au‐bipy‐Cu composite represents a new catalyst system for effective CO₂RR conversion to C‐products.     

Thiol‐Assisted Synthesis of Carbon‐Supported Metal Nanoparticles for Efficient Electrocatalytic CO2 Reduction

The typical preparation route of carbon‐supported metallic catalyst is complex and uneconomical. Herein, we reported a thiol‐assisted one‐pot method by using 3‐mercaptopropionic acid (MPA) to synthesize carbon‐supported metal nanoparticles catalysts for efficient electrocatalytic reduction of carbon dioxide (CO₂RR). We found that the synthesized Au?MPA/C catalyst achieves a maximum CO faradaic efficiency (FE) of 96.2% with its partial current density of ?11.4 mA/cm², which is much higher than that over Au foil or MPA‐free carbon‐supported Au (Au/C). The performance improvement in CO₂RR over the catalyst is probably derived from the good dispersion of Au nanoparticles and the surface modification of the catalyst caused by the specific interaction between Au nanoparticles and MPA. This thiol‐assisted method can be also extended to synthesize Ag?MPA/C with enhanced CO₂RR performance.     

Pd-Cu-Clx/Al2O3催化剂对CO氧化的稳定性

CO催化氧化广泛应用于空气净化、机动车尾气治理和CO气体传感器中.在CO氧化催化剂设计与制备过程中,催化剂与使用环境密切相关.例如工业和机动车尾气净化需要在高温(200–600°C)下进行,而对于半密闭空间(隧道或者地下停车场)空气净化需要在室温和高相对湿度下进行.频繁冷启动导致半密闭空间CO浓度累积而超过排放控制标准,因此制备室温、高相对湿度下CO氧化催化剂是面临的重要问题之一.负载型Wacker催化剂对于CO低温催化氧化的研究一直受到广泛关注.环境中少量水的存在会促进负载型Wacker催化剂对CO的低温氧化性能,但随着水沉积量的增加,活性位点将被覆盖,并且Pd和Cu活性组分之间的紧密结构被破坏,从而导致催化剂的失活,即催化剂的稳定性变差.因此,为了提高催化剂在高相对湿度下的稳定性,利用二乙氧基二甲基硅烷对Al2O3载体进行硅烷化处理,以增加载体的疏水性,考察载体疏水改性对CO低温氧化过程中催化剂稳定性的影响.催化剂的稳定性测试结果表明,在0°C,100%相对湿度条件下,未改性催化剂在约20 h内CO转化率由81%下降到50%;载体硅烷化后制备的催化剂在反应进行150 h后,CO转化率仍保持在78%,即反应活性未见降低.由此表明催化剂载体经有机硅烷改性后,可显著增强催化剂在低温、高相对湿度下的稳定性.N2吸附/脱附和水吸附实验结果表明,载体硅烷化改性并未对催化剂的比表面积产生影响,但显著降低了催化剂上水沉积速度和沉积量,未改性催化剂的初始吸水速度是改性后催化剂的4倍,但改性后催化剂的饱和吸水率仅占未改性催化剂的1/3.X射线衍射结果表明,载体预处理后活性物种Cu2(OH)3Cl晶粒尺寸有所增加.氢气程序升温还原、X射线光电子能谱结果表明,载体硅烷化预处理改善了催化剂中Cu和Pd物种的化学分布及接触状态,增加了与Pd物种紧密接触的Cu物种的量,从而促进了Cu物种的还原.与此同时,载体硅烷化显著降低了催化剂表面Cl离子的浓度,从而影响到对CO吸附.为了进一步研究水与催化剂稳定性之间的关系,采用原位红外漫反射(In situ DRIFT)对催化剂进行表征.负载型Wacker催化剂对CO氧化反应机理为:Pd是CO氧化反应的活性中心,通过Pd和Cu物种之间的氧化还原循环来实现CO氧化,且Pd+比Pd2+具有更高的CO氧化性能.反应气氛中水的存在,有利于CO在Pd+上氧化、以及金属态Pd被Cu2+物种再氧化的过程,同时水也显著促进了催化剂表面碳酸盐的生成以及抑制了活性物种Pd+生成.与表面碳酸盐累积相比,水对于活性物种Pd+生成的抑制作用是导致催化剂活性降低的主要原因.     

Proton Shuttling by Polyaniline of High Brønsted Basicity for Improved Electrocatalytic Ethylene Production from CO2

Hybrid organic/inorganic composites with the organic phase tailored to modulate local chemical environment at the Cu surface arise as an enchanting category of catalysts for electrocatalytic CO₂ reduction reaction (CO₂RR). A fundamental understanding on how the organics of different functionality, polarity, and hydrophobicity affect the reaction path is, however, still lacking to guide rational catalyst design. Herein, polypyrrole (PPy) and polyaniline (PANI) manifesting different Brønsted basicity are compared for their regulatory roles on the CO₂RR pathways regarding *CO coverage, proton source and interfacial polarity. Concerted efforts from in situ IR, Raman and operando modelling unveil that at the PPy/Cu interface with limited *CO coverage, hydridic *H produced by the Volmer step favors the carbon hydrogenation of *CO to form *CHO through a Tafel process; Whereas at the PANI/Cu interface with concentrated CO₂ and high *CO coverage, protonic H⁺ shuttled through the benzenoid -NH- protonates the oxygen of *CO, yielding *COH for asymmetric coupling with nearby *CO to form *OCCOH under favored energetics. As a result of the tailored chemical environment, the restructured PANI/Cu composite demonstrates a high partial current density of 0.41 A cm⁻² at a maximal Faraday efficiency of 67.5 % for ethylene production, ranking among states of the art.     

Polyethylenimine‐assisted Synthesis of Au Nanoparticles for Efficient Syngas Production

The ability to capture, store, and use CO₂ is important for remediating greenhouse‐gas emissions and combatting global warming. Herein, Au nanoparticles (Au‐NPs) are synthesized for effective electrochemical CO₂ reduction and syngas production, using polyethylenimine (PEI) as a ligand molecule. The PEI‐assisted synthesis provides uniformly sized 3‐nm Au NPs, whereas larger irregularly shaped NPs are formed in the absence of PEI in the synthesis solution. The Au‐NPs synthesized with PEI (PEI?Au/C, average PEI Mw=2000) exhibit improved CO₂ reduction activities compared to Au‐NPs formed in the absence of PEI (bare Au NPs/C). PEI?Au/C displays a 34 % higher activity toward CO₂ reduction than bare Au NPs/C; for example, PEI?Au/C exhibits a CO partial current density (j_CO) of 28.6 mA cm^?2 at ?1.13 V_RHE, while the value for bare Au NPs/C is 21.7 mA cm^?2; the enhanced j_CO is mainly due to the larger surface area of PEI?Au/C. Furthermore, the PEI?Au/C electrode exhibits stable performance over 64 h, with an hourly current degradation rate of 0.25 %. The developed PEI?Au/C is employed in a CO₂‐reduction device coupled with an IrO₂ water‐oxidation catalyst and a proton‐conducting perfluorinated membrane to form a PEI?Au/C|Nafion|IrO₂ membrane‐electrode assembly. The device using PEI?Au/C as the CO₂‐reduction catalyst exhibits a j_CO of 4.47 mA/cm² at 2.0 V_cell. Importantly, the resulted PEI?Au/C is appropriate for efficient syngas production with a CO ratio of around 30–50 %.     

Avoiding Self‐Poisoning: A Key Feature for the High Activity of Au/Mg(OH)2 Catalysts in Continuous Low‐Temperature CO Oxidation

Au/Mg(OH)₂ catalysts have been reported to be far more active in the catalytic low‐temperature CO oxidation (below 0 °C) than the thoroughly investigated Au/TiO₂ catalysts. Based on kinetic and in situ infrared spectroscopy (DRIFTS) measurements, we demonstrate that the comparatively weak interaction of Au/Mg(OH)₂ with CO₂ formed during the low‐temperature reaction is the main reason for the superior catalyst performance. This feature enables rapid product desorption and hence continuous CO oxidation at temperatures well below 0 °C. At these temperatures, Au/TiO₂ also catalyzes CO₂ formation, but does not allow for CO₂ desorption, which results in self‐poisoning. At higher temperatures (above 0 °C), however, CO₂ formation is rate‐limiting, which results in a much higher activity for Au/TiO₂ under these reaction conditions.     

Catalytic gold nanoparticles for fluorescent detection of mercury(II) and lead(II) ions

In this study, we developed a fluorescence assay for the highly sensitive and selective detection of Hg²⁺ and Pb²⁺ ions using a gold nanoparticle (Au NP)-based probe. The Hg–Au and Pb–Au alloys that formed on the Au NP surfaces allowed the Au NPs to exhibit peroxidase-mimicking catalytic activity in the H₂O₂-mediated oxidation of Amplex UltraRed (AUR). The fluorescence of the AUR oxidation product increased upon increasing the concentration of either Hg²⁺ or Pb²⁺ ions. By controlling the pH values of 5 mM tris–acetate buffers at 7.0 and 9.0, this H₂O₂–AUR–Au NP probe detected Hg²⁺ and Pb²⁺ ions, respectively, both with limits of detection (signal-to-noise ratio: 3) of 4.0 nM. The fluorescence intensity of the AUR oxidation product was proportional to the concentrations of Hg²⁺ and Pb²⁺ ions over ranges 0.05–1 μM (R² = 0.993) and 0.05–5 μM (R² = 0.996), respectively. The H₂O₂–AUR–Au NP probe was highly selective for Hg²⁺ (>100-fold) and Pb²⁺ (>300-fold) ions in the presence of other tested metal ions. We validated the practicality of this simple, selective, and sensitive H₂O₂–AUR–Au NP probe through determination of the concentrations of Hg²⁺ and Pb²⁺ ions in a lake water sample and of Pb²⁺ ions in a blood sample. To the best of our knowledge, this system is the first example of Au NPs being used as enzyme-mimics for the fluorescence detection of Hg²⁺ and Pb²⁺ ions.     

Electrochemical Conversion of CO2 to Syngas with Controllable CO/H2 Ratios over Co and Ni Single‐Atom Catalysts

The electrochemical CO₂ reduction reaction (CO₂RR) to yield synthesis gas (syngas, CO and H₂) has been considered as a promising method to realize the net reduction in CO₂ emission. However, it is challenging to balance the CO₂RR activity and the CO/H₂ ratio. To address this issue, nitrogen‐doped carbon supported single‐atom catalysts are designed as electrocatalysts to produce syngas from CO₂RR. While Co and Ni single‐atom catalysts are selective in producing H₂ and CO, respectively, electrocatalysts containing both Co and Ni show a high syngas evolution (total current >74 mA cm^?2) with CO/H₂ ratios (0.23–2.26) that are suitable for typical downstream thermochemical reactions. Density functional theory calculations provide insights into the key intermediates on Co and Ni single‐atom configurations for the H₂ and CO evolution. The results present a useful case on how non‐precious transition metal species can maintain high CO₂RR activity with tunable CO/H₂ ratios.     

通过CeOx修饰提高金纳米颗粒在CO氧化反应中的催化活性和耐久性

CO催化氧化是一个重要的经典反应,与许多应用息息相关,包括痕量CO气体检测、汽车尾气净化和安全防护等,吸引了人们广泛的研究兴趣.负载型Au纳米颗粒在CO氧化等许多反应中有着与众不同的催化活性,具有广泛的应用前景,但依然存在着稳定性差、易团聚失活的问题.人们通过应用多孔载体隔离Au纳米颗粒,在Au纳米颗粒表面覆盖金属氧化物、二氧化硅或碳,以及对Au纳米粒子进行封装等方法解决这些问题.尤其是利用金属氧化物与Au纳米粒子间的强相互作用对其进行覆盖或封装,有效地提高了Au催化材料的稳定性.但以上策略操作流程复杂,不利于应用.本文发展了一种简单有效的方法,通过EDTA的络合作用引入CeOx对Au纳米粒子进行修饰,得到的CeOx@Au/SiO2催化剂活性和耐久性明显提升.采用X射线衍射(XRD)和高分辨透射电子显微镜(HRTEM)证明了CeOx成功地修饰在Au纳米颗粒上.且通过EDTA引入CeOx所制备的CeOx@Au/SiO2催化剂结构明显不同于直接加入纳米CeO2所得到的CeOx-Au/SiO2的结构.EDTA的络合作用能有效地连结Ce与Au物种,经焙烧消除EDTA后,加强了CeOx与Au间相互作用,最终在Au纳米粒子表面形成丰富的CeOx颗粒与原子级厚度的CeOx层.进一步应用X射线光电子能谱(XPS)和氢气程序升温还原(H2-TPR)等手段研究了CeOx修饰对Au纳米粒子的影响.XPS结果表明,CeOx@Au/SiO2催化剂带正电的Au+和Au3+的浓度明显高于一般的Au/SiO2和直接加入CeO2制备得到的CeOx-Au/SiO2催化剂.H2-TPR同样表明,CeOx修饰调变了Au纳米粒子的氧化还原性.这些均对其在CO催化氧化反应中的催化活性具有重要影响将CeOx@Au/SiO2催化剂用于CO催化氧化反应中,160°C时,CO转化率达98.8％,至180°C后实现了CO的完全转化.而一般的Au/SiO2催化剂在160°C时CO转化率仅为4.0％,CO的完全转化则需340°C.直接加入纳米CeO2所得到的CeOx-Au/SiO2催化剂,其催化活性略有提升,CO完全转化所需的温度为300°C.这充分证明了通过CeOx修饰Au纳米粒子,能有效提升其催化活性.原位漫反射红外光谱(DRIFT)结果表明,CeOx修饰促进了CO在Au表面的吸附,并能形成[Au(CO)2]δ+物种;同时还观察到大量的单齿CO32? 物种信号,反映了CeOx@Au/SiO2催化剂表面存在丰富的活性氧物种.通入O2后,观察到了大量CO32?物种信号和气相CO2,印证了催化剂表面发生的CO催化氧化过程,也表明其具有非常高的催化活性.考察了CeOx@Au/SiO2催化剂的耐久性,发现经50 h CO氧化反应,催化剂依然能有效保持活性.相比之下,Au/SiO2催化剂经10 h反应后,开始明显失活.由此可见,CeOx@Au/SiO2催化剂具有相当高的耐久性.在600°C将催化剂焙烧3 h,发现Au/SiO2催化剂中Au纳米粒子存在明显团聚现象,而CeOx@Au/SiO2催化剂的Au纳米粒子依然均匀分布在载体表面,且粒径未发生明显变化.     

Low temperature CO oxidation on Au/TiO2 sol-gel catalysts

A comparative study on Au/TiO₂catalysts prepared by impregnation with HAuCl₄of commercial TiO₂ or by impregnation of sol-gel derived TiO₂has been carried out during CO oxidation. Specific surface areas and mean Au particle of 49 and 74 m²/g and 35 and 25 Å were obtained for impregnated commercial TiO₂ and sol-gel preparations, respectively. XRD patterns shown that in sol-gel derived TiO₂ only anatase phase was identified, while in commercial TiO₂ anatase and rutile phases co-exist. Titania support effect on Au activity for the oxidation of CO has been observed. The light-off during the reaction on Au/TiO₂initiates at 50°C, whereas for commercial impregnated TiO₂ catalyst the light-off initiates at 200°C.     

Electrochemical Conversion of CO2 to Syngas with Controllable CO/H2 Ratios over Co and Ni Single-Atom Catalysts

The electrochemical CO₂ reduction reaction (CO₂RR) to yield synthesis gas (syngas, CO and H₂) has been considered as a promising method to realize the net reduction in CO₂ emission. However, it is challenging to balance the CO₂RR activity and the CO/H₂ ratio. To address this issue, nitrogen-doped carbon supported single-atom catalysts are designed as electrocatalysts to produce syngas from CO₂RR. While Co and Ni single-atom catalysts are selective in producing H₂ and CO, respectively, electrocatalysts containing both Co and Ni show a high syngas evolution (total current >74 mA cm⁻²) with CO/H₂ ratios (0.23–2.26) that are suitable for typical downstream thermochemical reactions. Density functional theory calculations provide insights into the key intermediates on Co and Ni single-atom configurations for the H₂ and CO evolution. The results present a useful case on how non-precious transition metal species can maintain high CO₂RR activity with tunable CO/H₂ ratios.     

Electrocatalysts Derived from Copper Complexes Transform CO into C2+ Products Effectively in a Flow Cell

Electrochemical reactors that electrolytically convert CO₂ into higher-value chemicals and fuels often pass a concentrated hydroxide electrolyte across the cathode. This strongly alkaline medium converts the majority of CO₂ into unreactive HCO₃⁻ and CO₃²⁻ byproducts rather than into CO₂ reduction reaction (CO2RR) products. The electrolysis of CO (instead of CO₂) does not suffer from this undesirable reaction chemistry because CO does not react with OH⁻. Moreover, CO can be more readily reduced into products containing two or more carbon atoms (i. e., C₂₊ products) compared to CO₂. We demonstrate here that an electrocatalyst layer derived from copper phthalocyanine ( CuPc ) mediates this conversion effectively in a flow cell. This catalyst achieved a 25 % higher selectivity for acetate formation at 200 mA/cm² than a known state-of-art oxide-derived Cu catalyst tested in the same flow cell. A gas diffusion electrode coated with CuPc electrolyzed CO into C₂₊ products at high rates of product formation (i. e., current densities ≥200 mA/cm²), and at high faradaic efficiencies for C₂₊ production (FE_C2+; >70 % at 200 mA/cm²). While operando Raman spectroscopy did not reveal evidence of structural changes to the copper molecular complex, X-ray photoelectron spectroscopy suggests that the catalyst undergoes conversion to a metallic copper species during catalysis. Notwithstanding, the ligand environment about the metal still impacts catalysis, which we demonstrated through the study of a homologous CuPc bearing ethoxy substituents. These findings reveal new strategies for using metal complexes for the formation of carbon-neutral chemicals and fuels at industrially relevant conditions.     

Elucidating the Electrocatalytic CO2 Reduction Reaction over a Model Single‐Atom Nickel Catalyst

Designing effective electrocatalysts for the carbon dioxide reduction reaction (CO₂RR) is an appealing approach to tackling the challenges posed by rising CO₂ levels and realizing a closed carbon cycle. However, fundamental understanding of the complicated CO₂RR mechanism in CO₂ electrocatalysis is still lacking because model systems are limited. We have designed a model nickel single‐atom catalyst (Ni SAC) with a uniform structure and well‐defined Ni‐N₄ moiety on a conductive carbon support with which to explore the electrochemical CO₂RR. Operando X‐ray absorption near‐edge structure spectroscopy, Raman spectroscopy, and near‐ambient X‐ray photoelectron spectroscopy, revealed that Ni⁺ in the Ni SAC was highly active for CO₂ activation, and functioned as an authentic catalytically active site for the CO₂RR. Furthermore, through combination with a kinetics study, the rate‐determining step of the CO₂RR was determined to be *CO₂^?+H⁺→*COOH. This study tackles the four challenges faced by the CO₂RR; namely, activity, selectivity, stability, and dynamics.     

Characteristics of Au/MgxAlO hydrotalcite catalysts in CO selective oxidation

Gold catalysts, supported on a solid base of Mg_xAlO hydrotalcite, were prepared by a modified deposition precipitation method for CO selective oxidation. The preparation parameters and pretreatment of the catalysts were investigated. The pH and the HAuCl₄ concentration in the initial solution, and the Mg/Al molar ratio of Mg_xAlO affected the pH in the final solution and determined the actual gold loading of the catalyst. The calcination temperatures of the Mg_xAlO support and the Au/Mg_xAlO catalyst dominated the Au³⁺/Au⁰ ratio on the catalyst. The pretreatment of the catalyst as well as the gold loading and the Au³⁺/Au⁰ ratio, critically determined the activity of the catalyst for CO selective oxidation. Based on XPS and in situ DR-FTIR analyses, a mechanism for CO selective oxidation on 2%Au/Mg₂AlO was proposed. The hydroxyl group on Mg₂AlO also participated in the reaction.     

Elucidating the Electrocatalytic CO2 Reduction Reaction over a Model Single-Atom Nickel Catalyst

Designing effective electrocatalysts for the carbon dioxide reduction reaction (CO₂RR) is an appealing approach to tackling the challenges posed by rising CO₂ levels and realizing a closed carbon cycle. However, fundamental understanding of the complicated CO₂RR mechanism in CO₂ electrocatalysis is still lacking because model systems are limited. We have designed a model nickel single-atom catalyst (Ni SAC) with a uniform structure and well-defined Ni-N₄ moiety on a conductive carbon support with which to explore the electrochemical CO₂RR. Operando X-ray absorption near-edge structure spectroscopy, Raman spectroscopy, and near-ambient X-ray photoelectron spectroscopy, revealed that Ni⁺ in the Ni SAC was highly active for CO₂ activation, and functioned as an authentic catalytically active site for the CO₂RR. Furthermore, through combination with a kinetics study, the rate-determining step of the CO₂RR was determined to be *CO₂⁻+H⁺→*COOH. This study tackles the four challenges faced by the CO₂RR; namely, activity, selectivity, stability, and dynamics.     

Breaking K+ Concentration Limit on Cu Nanoneedles for Acidic Electrocatalytic CO2 Reduction to Multi-Carbon Products

Electrocatalytic CO₂ reduction reaction (CO₂RR) to multi-carbon products (C₂₊) in acidic electrolyte is one of the most advanced routes for tackling our current climate and energy crisis. However, the competing hydrogen evolution reaction (HER) and the poor selectivity towards the valuable C₂₊ products are the major obstacles for the upscaling of these technologies. High local potassium ions (K⁺) concentration at the cathode's surface can inhibit proton-diffusion and accelerate the desirable carbon-carbon (C−C) coupling process. However, the solubility limit of potassium salts in bulk solution constrains the maximum achievable K⁺ concentration at the reaction sites and thus the overall acidic CO₂RR performance of most electrocatalysts. In this work, we demonstrate that Cu nanoneedles induce ultrahigh local K⁺ concentrations (4.22 M) – thus breaking the K⁺ solubility limit (3.5 M) – which enables a highly efficient CO₂RR in 3 M KCl at pH=1. As a result, a Faradaic efficiency of 90.69±2.15 % for C₂₊ (FE_C2+) can be achieved at 1400 mA.cm⁻², simultaneous with a single pass carbon efficiency (SPCE) of 25.49±0.82 % at a CO₂ flow rate of 7 sccm.     

Dual-Role of Polyelectrolyte-Tethered Benzimidazolium Cation in Promoting CO2/Pure Water Co-Electrolysis to Ethylene

Electrochemical CO₂ reduction reaction (CO₂RR), as a promising route to realize negative carbon emissions, is known to be strongly affected by electrolyte cations (i.e., cation effect). In contrast to the widely-studied alkali cations in liquid electrolytes, the effect of organic cations grafted on alkaline polyelectrolytes (APE) remains unexplored, although APE has already become an essential component of CO₂ electrolyzers. Herein, by studying the organic cation effect on CO₂RR, we find that benzimidazolium cation (Beim⁺) significantly outperforms other commonly-used nitrogenous cations (R₄N⁺) in promoting C₂₊ (mainly C₂H₄) production over copper electrode. Cyclic voltammetry and in situ spectroscopy studies reveal that the Beim⁺ can synergistically boost the CO₂ to *CO conversion and reduce the proton supply at the electrocatalytic interface, thus facilitating the *CO dimerization toward C₂₊ formation. By utilizing the homemade APE ionomer, we further realize efficient C₂H₄ production at an industrial-scale current density of 331 mA cm⁻² from CO₂/pure water co-electrolysis, thanks to the dual-role of Beim⁺ in synergistic catalysis and ionic conduction. This study provides a new avenue to boost CO₂RR through the structural design of polyelectrolytes.     

Covalently Grafting Graphene onto Si Photocathode to Expedite Aqueous Photoelectrochemical CO2 Reduction

Silicon semiconductor functionalized with molecular catalysts emerges as a promising cathode for photoelectrochemical (PEC) CO₂ reduction reaction (CO₂RR). However, the limited kinetics and stabilities remains a major hurdle for the development of such composites. We herein report an assembling strategy of silicon photocathodes via chemically grafting a conductive graphene layer onto the surface of n⁺-p Si followed by catalyst immobilization. The covalently-linked graphene layer effectively enhances the photogenerated carriers transfer between the cathode and the reduction catalyst, and improves the operating stability of the electrode. Strikingly, we demonstrate that altering the stacking configuration of the immobilized cobalt tetraphenylporphyrin (CoTPP) catalyst through calcination can further enhance the electron transfer rate and the PEC performance. At the end, the graphene-coated Si cathode immobilized with CoTPP catalyst managed to sustain a stable 1-Sun photocurrent of −1.65 mA cm⁻² over 16 h for CO production in water at a near neutral potential of −0.1 V vs. reversible hydrogen electrode. This represents a remarkable improvement of PEC CO₂RR performance in contrast to the reported photocathodes functionalized with molecular catalysts.     

Visible‐Light‐Driven CO2 Reduction by Mesoporous Carbon Nitride Modified with Polymeric Cobalt Phthalocyanine

The integration of molecular catalysts with low‐cost, solid light absorbers presents a promising strategy to construct catalysts for the generation of solar fuels. Here, we report a photocatalyst for CO₂ reduction that consists of a polymeric cobalt phthalocyanine catalyst (CoPPc) coupled with mesoporous carbon nitride (mpg‐CN_x) as the photosensitizer. This precious‐metal‐free hybrid catalyst selectively converts CO₂ to CO in organic solvents under UV/Vis light (AM 1.5G, 100 mW cm^?2, λ>300 nm) with a cobalt‐based turnover number of 90 for CO after 60 h. Notably, the photocatalyst retains 60 % CO evolution activity under visible light irradiation (λ>400 nm) and displays moderate water tolerance. The in situ polymerization of the phthalocyanine allows control of catalyst loading and is key for achieving photocatalytic CO₂ conversion.