Electrochemistry at cobalt(II)tetrasulfophthalocyanine-multi-walled carbon nanotubes modified glassy carbon electrode: a sensing platform for efficient suppression of ascorbic acid in the presence of epinephrine

Electrochemistry of water-soluble cobalt(II) tetrasulfophthalocyanine (CoTSPc) electrodeposited on glassy carbon nanotube pre-modified with acid-functionalized multi-walled carbon nanotubes (MWCNT) is described. Both charge transfer resistances toward [Fe(CN)₆]^3−/4− redox probe and electrocatalytic responses toward epinephrine (EP) detection follow the trend: bare GCE < GCE-MWCNT < GCE-CoTSPc < GCE-MWCNT-CoTSPc. EP analysis was then carried out in details using GCE-MWCNT-CoTSPc. The catalytic rate constant value k _ch = 2.2 × 10⁷ (mol cm⁻³)⁻¹ s⁻¹ was obtained from rotating disk electrode experiment. Interestingly, GCE-MWCNT-CoTSPc efficiently suppressed the detection of ascorbic acid (the natural interference of neurotransmitters in physiological conditions) showing good sensitivity (0.132 ± 0.003 A l mol⁻¹), limit of detection (4.517 × 10⁻⁷ mol l⁻¹), and quantification (15.056 × 10⁻⁷ mol l⁻¹). In addition, GCE-MWCNT-CoTSPc was conveniently used to determine EP in epinephrine hydrochloric acid injection with recovery of 101.1 ± 2.2%.     

Selective determination of uric acid in the presence of ascorbic acid using a penicillamine self-assembled gold electrode

The electrochemical behaviors of uric acid (UA) at the penicillamine (Pen) self-assembled monolayers modified gold electrode (Pen/Au) have been studied. The Pen/Au electrode is demonstrated to promote the electrochemical response of UA by cyclic voltammetry (CV). The diffusion coefficient D of UA is 6.97 × 10⁻⁶ cm² s⁻¹. In differential pulse voltammetric (DPV) measurements, the Pen/Au electrode can separate the UA and ascorbic acid (AA) oxidation potentials by about 120 mV and can be used for the selective determination of UA in the presence of AA. The detection limit was 1 × 10⁻⁶ mol L⁻¹. The modified electrode shows excellent sensitivity, good selectivity and antifouling properties.     

Simultaneous determination of uric acid and ascorbic acid at the film of chitosan incorporating cetylpyridine bromide modified glassy carbon electrode

A glassy carbon electrode (GCE) modified with the film composed of chitosan incorporating cetylpyridine bromide is constructed and used to determine uric acid (UA) and ascorbic acid (AA) by differential pulse voltammetry (DPV). This modified electrode shows efficient electrocatalytic activity and fairly selective separation for oxidation of AA and UA in mixture solution. UA is catalyzed by this modified electrode in phosphate buffer solution (pH 4.0) with a decrease of 80 mV, while AA is catalyzed with a decrease of 200 mV in overpotential compared to GCE, and the peak separation of oxidation between AA and UA is 260 mV, which is large enough to allow the determination of one in presence of the other. Under the optimum conditions, the anodic peak currents (I _pa) of DPV are proportional to the concentration of UA in the range of 2.0 × 10⁻⁶ to 6.0 × 10⁻⁴ M, with the detection limit of 5.0 × 10⁻⁷ M at a signal-to-noise ratio of 3 (S/N = 3) and to that of AA in the range of 4.0 × 10⁻⁶ to 1.0 × 10⁻³ M, with the detection limit of 8.0 × 10⁻⁷ M (S/N = 3).     

Electrochemical characterization of 2, 2′-[1, 2-ethanediylbis (nitriloethylidyne)]-bis-hydroquinone-carbon nanotube paste electrode and its application to simultaneous voltammetric determination of ascorbic acid and uric acid

The preparation and electrochemical characterization of a carbon nanotube paste electrode modified with 2,2′-[1,2-ethanediylbis (nitriloethylidyne)]-bis-hydroquinone, referred to as EBNBH, was investigated. The EBNBH carbon nanotube paste electrode (EBNBHCNPE) displayed one pair of reversible peaks at E _pa = 0.18 V and E _pc = 0.115 V vs Ag/AgCl. Half wave potential (E _1/2) and ΔE _p were 0.148 and 0.065 V vs Ag/AgCl, respectively. The electrocatalytic oxidation of ascorbic acid (AA) has been studied on EBNBHCNPE, using cyclic voltammetry, differential pulse voltammetry and chronoamperometry techniques. It has been shown that the oxidation of AA occurs at a potential where oxidation is not observed at the unmodified carbon paste electrode. The heterogeneous rate constant for oxidation of AA at the EBNBHCNPE was also determined and found to be about 1.07 × 10⁻³ cm s⁻¹. The diffusion coefficient of AA was also estimated as 5.66 × 10⁻⁶ cm² s⁻¹ for the experimental conditions, using chronoamperometry. Also, this modified electrode presented the property of electrocatalysing the oxidation of AA and uric acid (UA) at 0.18 and 0.35 V vs Ag/AgCl, respectively. The separations of anodic peak potentials of AA and UA reached 0.17 V. Using differential pulse voltammetry, the calibration curves for AA and UA were obtained over the range of 0.1–800 μM and 20–700 μM, respectively. With good selectivity and sensitivity, the present method provides a simple method for selective detection of AA and UA in biological samples.     

Electrochemical methods for simultaneous determination of trace amounts of dopamine and uric acid using a carbon paste electrode incorporated with multi-wall carbon nanotubes and modified with α-cyclodextrine

In this work, we investigate the electrochemical activity of dopamine (DA) and uric acid (UA) using both a bare and a modified carbon paste electrode as the working electrode, with a platinum wire as the counter electrode and a silver/silver chloride (Ag/AgCl) as the reference electrode. The modified carbon paste electrode consists of multi-walled carbon nanotubes (>95%) treated with α-cyclodextrine, resulting in an electrode that exhibits a significant catalytic effect toward the electro-chemical oxidation of DA in a 0.2-M Britton–Robinson buffer solution (pH 5.0). The peak current increases linearly with the DA concentration within the molar concentration ranges of 2.0 × 10⁻⁶ to 5.0 × 10⁻⁵ M and 5.0 × 10⁻⁵ to 1.9 × 10⁻⁴ M. The detection limit (signal to noise >3) for DA was found to be 1.34 × 10⁻⁷ M, respectively. In this work, voltammetric methods such as cyclic voltammetry, chronoamperometry, chronocuolometry, differential pulse and square wave voltammetry, and linear sweep and hydrodynamic voltammetry were used. Cyclic voltammetry was used to investigate the redox properties of the modified electrode at various scan rates. The diffusion coefficient (D, cm² s⁻¹ = 3.05 × 10⁻⁵) and the kinetic parameters such as the electron transfer coefficient (α = 0.51) and the rate constant (k, cm³ mol⁻¹ s⁻¹ = 1.8 × 10³) for DA were determined using electrochemical approaches. By using differential pulse voltammetry for simultaneous measurements, we obtained two peaks for DA and UA in the same solution, with the peak separation approximately 136 mV. The average recovery was measured at 102.45% for DA injection.     

Electrocatalytic oxidation of aspirin and acetaminophen on a cobalt hydroxide nanoparticles modified glassy carbon electrode

The electrocatalytic oxidation of aspirin and acetaminophen on nanoparticles of cobalt hydroxide electrodeposited on the surface of a glassy carbon electrode in alkaline solution was investigated. The process of oxidation and the kinetics have been investigated using cyclic voltammetry, chronoamperometry, and steady-state polarization measurements. Voltammetric studies have indicated that in the presence of drugs, the anodic peak current of low valence cobalt species increases, followed by a decrease in the corresponding cathodic current. This indicates that drugs are oxidized on the redox mediator which is immobilized on the electrode surface via an electrocatalytic mechanism. With the use of Laviron’s equation, the values of anodic and cathodic electron-transfer coefficients and charge-transfer rate constant for the immobilized redox species were determined as α _s,a = 0.72, α _s,c = 0.30, and k _s = 0.22 s⁻¹. The rate constant, the electron transfer coefficient, and the diffusion coefficient involved in the electrocatalytic oxidation of drugs were reported. It was shown that by using the modified electrode, aspirin and acetaminophen can be determined by amperometric technique with detection limits of 1.88 × 10⁻⁶ and 1.83 × 10⁻⁶ M, respectively. By analyzing the content of acetaminophen and aspirin in bulk forms using chronoamperometric and amperometric techniques, the analytical utility of the modified electrode was achieved. The method was also proven to be valid for analyzing these drugs in urine samples.     

Voltammetric detection of riboflavin based on ordered mesoporous carbon modified electrode

The potential application of ordered mesoporous carbon (OMC)-modified glassy carbon electrode (OMC/GCE) in electrochemistry as a novel electrode material was investigated. X-ray diffraction, transmission electron micrographs, and cyclic voltammetry were used to characterize the structure and electrochemical behaviors of this material. Compared to GC electrode, the peak currents of potassium ferricyanide (K₃[Fe(CN)₆]) increase and the peak potential separation (ΔE _p) decreases at the OMC/GC electrode. These phenomena suggest that OMC-modified GC electrode possesses larger electrode area and faster electron transfer rate, as compared with bare GC electrode. Furthermore, riboflavin was detected using OMC/GC electrode in aqueous solutions. The results showed that, under an optimum condition (pH 7.0), the OMC/GC electrode exhibited excellent response performance to riboflavin in the concentration range of 4.0 × 10⁻⁷ to 1.0 × 10⁻⁶ M with a high sensitivity of 769 μA mM⁻¹. The detection limit was down to around 2 × 10⁻⁸ M. With good stability and reproducibility, the present OMC/GC electrode was applied in the determination of vitamin B₂ content in vitamin tablets, and satisfactory results were obtained.     

Simultaneous voltammetric determination of ascorbic acid and dopamine at the surface of electrodes modified with self-assembled gold nanoparticle films

Gold nanoparticles (GNs) could be efficiently immobilized on binary mixed self-assembled monolayers (SAMs) on a gold surface composed of 1,6-hexanedithiol and 1-octanethiol (nano-Au/SAMs gold electrode). This GN chemically modified electrode was used for electrochemical determination of ascorbic acid (AA) and dopamine (DA) in aqueous media. The result showed that the GN-modified electrode could clearly resolve the oxidation peaks of AA and DA, with a peak-to-peak separation (∆E _p) of 110 mV enabling determination of AA and DA in the presence of each other. The linear analytical curves were obtained in the ranges of 0.3–1.4 mM for AA and 0.2–1.2 mM for DA concentrations using differential pulse voltammetry. The detection limits (3σ) were 9.0 × 10⁻⁵ M for AA and 9.0 × 10⁻⁵ M for DA.     

Electrochemical,microscopic, and EQCM studies of cathodic electrodeposition of ZnO/FAD and anodic polymerization of FAD films modified electrodes and their electrocatalytic properties

Two kinds of chemically modified electrodes were prepared. In the first type of electrodes, zinc oxide (ZnO) and flavin adenine dinucleotide (FAD) molecules were deposited onto the glassy carbon-, gold-, and SnO₂-coated glass electrodes by using cyclic voltammetry from the bath solution containing aqueous 0.1 M zinc nitrate, 0.1 M sodium nitrate, and 1 × 10⁻⁴ M FAD. It was called as ZnO/FAD modified electrodes. The second type of modified electrode was prepared by the electropolymerization method. Electrochemical polymerization of FAD was carried out from the acidic solution containing 1 × 10⁻⁴ M FAD monomers onto electrode surfaces. This poly(FAD)-modified electrode yields a new redox couple in addition to the monomers redox couple. The influence of the concentrations, pH, and electrocatalytic properties of the ZnO/FAD- and poly(FAD)-modified electrodes are investigated by means of the in situ technique electrochemical quartz–crystal microgravimetry (EQCM) combined with cyclic voltammetry and the ex situ technique scanning electron microscopy. From these studies, it appears that the cathodic deposition of ZnO/FAD-modified electrodes gives only one redox couple, and the anodically polymerized FAD film-modified electrodes gives two reversible redox couples. The pH dependence of the redox responses were investigated and the kinetics of electron transfer was evaluated. In addition, the EQCM technique was employed to follow the deposition process of both kinds of modified electrodes in real time as well as the characteristics of the charge transfer associated with the surface-confined redox-active couples. The electrocatalytic activity of the poly(FAD)-modified electrode towards the reduction of hydrogen peroxide and the oxidation of dopamine and ascorbic acid was explored. The important electrocatalytic properties of poly(FAD)-modified electrode were observed for simultaneous separation of dopamine and ascorbic acid in neutral solution. This poly(FAD)-modified electrode has several advantages than the previously reported FAD-modified electrodes.     

Simultaneous Determination of Dopamine and Ascorbic Acid at a Triazole Self-Assembled Monolayer-Modified Gold Electrode

A 3-amino-5-mercapto-1,2,4-triazole (TA) self-assembled monolayer-modified gold electrode (TA SAM/Au) is characterized by X-ray photoelectron spectroscopy, A.C. impedance, cyclic voltammetry, chronoamperometry and chronocoulometry. The TA SAM/Au exhibited good promotion of the electrochemical oxidation of dopamine. Some electrochemical parameters of dopamine such as electron transfer number, exchange current density, standard heterogeneous rate constant, diffusion coefficient, etc., were measured by different electrochemical methods. The peak currents of dopamine were linearly dependent on its concentration in the range of 1.5 × 10⁻⁶–1.0 × 10⁻⁴ mol L⁻¹, with a detection limit of 5.0 × 10⁻⁷ mol L⁻¹. The oxidative peak potentials of dopamine and ascorbic acid were well separated at about 190 ± 10 mV in pH 2.0 BR buffers at TA SAM/Au, the oxidation peak current increases approximately linearly with increasing concentration of both dopamine and ascorbic acid in the concentration range of 9.98 × 10⁻⁶–4.54 × 10⁻⁴ mol L⁻¹. It can be used for simultaneous determination of dopamine and ascorbic acid.     

Simultaneous voltammetric measurement of ascorbic acid and dopamine on poly(caffeic acid)-modified glassy carbon electrode

A poly(caffeic acid) thin film was deposited on the surface of a glassy carbon electrode by potentiostatic technique in an aqueous solution containing caffeic acid. The poly(caffeic acid)-modified electrode was used for the determination of ascorbic acid (AA), dopamine (DA), and their mixture by cyclic voltammetry. This modified electrode exhibited a potent and persistent electron-mediating behavior followed by well-separated oxidation peaks toward AA and DA at a scan rate of 10 mV s⁻¹ with a potential difference of 135 mV, which was large enough to determine AA and DA individually and simultaneously. The catalytic peak current obtained was linearly dependent on the AA and DA concentrations in the range of 2.0 × 10⁻⁵−1.2 × 10⁻³ and 1.0 × 10⁻⁶−4.0 × 10⁻⁵ mol L⁻¹ in 0.15 mol L⁻¹ phosphate buffer (pH 6.64). The detection limits for AA and DA were 9.0 × 10⁻⁶ and 4.0 × 10⁻⁷ mol L⁻¹, respectively. The modified electrode shows good sensitivity, selectivity, and stability and has been applied to the determination of DA and AA in real samples with satisfactory results.     

Caffeic acid modified glassy carbon electrode for electrocatalytic oxidation of reduced nicotinamide adenine dinucleotide (NADH)

A new modified electrode was prepared by electrodeposition of caffeic acid (CFA) at the surface of an activated glassy carbon electrode. Cyclic voltammetry was used to investigate the redox properties of this electrode at various solution pH values and at various scan rates. The pH dependence of the electrode response was found to be 58.5 mV/pH, which is very close to the expected Nernstian value. The electrode was also employed to study electrocatalytic oxidation of reduced nicotinamide adenine dinucleotide (NADH), using cyclic voltammetry, chronoamperometry and rotating disk voltammetry as diagnostic techniques. It was found that the modified electrode exhibits potent and persistent electrocatalytic properties toward NADH oxidation in phosphate buffer solution (pH 7.0) with a diminution of the overpotential of about 450 mV compared to the process at an unmodified electrode. The electrocatalytic current increases linearly with NADH concentration in the range tested from 0.05 to 1.0 mM. The apparent charge transfer rate constant and transfer coefficient for electron transfer between the electrode surface and immobilized CFA were calculated as 11.2 s⁻¹ and 0.43, respectively. The heterogeneous rate constant for oxidation of NADH at the CFA-modified electrode surface was also determined and found to be about 3 × 10³ M⁻¹ s⁻¹. Finally, the diffusion coefficient of NADH was calculated as 3.24 × 10⁻⁶ cm² s⁻¹ for the experimental conditions, using chronoamperometric results. Received: 6 January 1999 / Accepted: 11 May 1999     

Determination of chromium(VI) and total chromium in water by in-electrode coulometric titration in a porous glassy carbon electrode

Chromium(VI) is determined through its direct electrochemical reduction in the bulk of a porous glassy carbon electrode. An electrode filled with the acidified sample and Cr(VI) is reduced by means of a constant current whereas the potential of the electrode is monitored. The limits of detection and quantification were found to be 1.9 and 6.0 μg · L⁻¹, resp. The linear range, repeatability and reproducibility were found to be 5–500 μg · L⁻¹, 1.2, and 1.8%, resp. The influence of Fe(III), Ca(II), Mg(II), sulphates, nitrates, humic acids and surfactants was investigated. Total chromium was measured after chemical oxidation of Cr(III) to chromate by permanganate. The method was applied to analyses of water samples.     

Selective detection of dopamine with poly(diphenylamine sulfonic acid) modified electrode in the presence of ascorbic acid

A glassy carbon electrode was modified with electropolymerized film of diphenylamine sulfonic acid (DPASA). Electropolymerization was performed by cyclic voltammetry in 0.1 M KCl solution. The modified electrode showed an excellent electrocatalytic effect towards oxidation of dopamine (DA) and ascorbic acid (AA). Electrostatic interaction between the negatively charged poly(DPASA) film and either cationic DA species or anionic AA species favorably contributed to the redox response of DA and AA. Anodic peaks of DA and AA in their mixture were well separated by ca 168 and −11.8 mV. The proposed modified electrode was utilized for selective determination of dopamine in the concentration range of 5.0 × 10^t7–2.0 × 10⁻⁵ M in the presence of high concentration of ascorbic acid. Detection limit was 6.5 × 10⁻⁹ M.     

Electrocatalytic oxidation of pyridoxine (vitamin B<Subscript>6</Subscript>) on aluminum electrode modified by metallic palladium particles/iron (III) hexacyanoferrate (II) film

The electrocatalytic activity of a Prussian blue (PB) film on the aluminum electrode by taking advantage of the metallic palladium characteristic as an electron-transfer bridge (PB/Pd–Al) for electrooxidation of 2-methyl-3-hydroxy-4,5-bis (hydroxyl–methyl) pyridine (pyridoxine) is described. The catalytic activity of PB was explored in terms of Fe^III [Fe^III (CN)₆]/Fe^III [Fe^II (CN)₆]¹⁻ system. The best mediated oxidation of pyridoxine (PN) on the PB/Pd–Al-modified electrode was achieved in 0.5 M KNO₃ + 0.2 M potassium acetate of pH 6 at scan rate of 20 mV s⁻¹. The mechanism and kinetics of the catalytic oxidation reaction of PN were monitored by cyclic voltammetry and chronoamperometry. The results were explained using the theory of electrocatalytic reactions at chemically modified electrodes. The charge transfer-rate limiting reaction step is found to be a one-electron abstraction, whereas a two-electron charge transfer reaction is the overall oxidation reaction of PN by forming pyridoxal. The value of α, k, and D are 0.5, 1.2 × 10² M⁻¹ s⁻¹, and 1.4 × 10⁻⁵ cm² s⁻¹, respectively. Further examination of the modified electrodes shows that the modifying layers (PB) on the Pd–Al substrate have reproducible behavior and a high level of stability after posing it in the electrolyte or Pyridoxine solutions for a long time.     

Electrochemical Behavior of Uric Acid and Epinephrine at a Meso-2,3-Dimercaptosuccinic Acid Self-Assembled Gold Electrode

A self-assembled electrode with a meso-2,3-dimercaptosuccinic acid (DMSA) monolayer has been characterized by electrochemical quartz crystal microbalance and complex impedance analysis, surface enhanced Raman spectroscopy and cyclic voltammetry. The self-assembled electrode was used for the simultaneous electrochemical detection of epinephrine (EP) and uric acid (UA) in phosphate buffer of pH 7.7. The simultaneous oxidation of EP and UA was performed by cyclic voltammetry (CV) and differential pulse voltammetry (DPV), and the signals for each method were well separated with a potential difference of over 330 mV and without interference by each other. The detection limit of EP is 5.4 × 10⁻⁸ mol L⁻¹ by CV and 5.3 × 10⁻⁸ mol L⁻¹ by DPV and that of UA is 8.4 × 10⁻⁸ mol L⁻¹ by CV and 4.2 × 10⁻⁸ mol L⁻¹ by DPV. The DMSA self-assembled electrode can be applied to the simultaneous determination of EP and UA.     

Simultaneous determination of uric acid and ascorbic acid at a ferrocenium–thioglycollate modified electrode

Self-assembled monolayers (SAMS) of chemisorbed thioglycollate on a gold electrode surface have been used as a base interface for the electrostatic adsorption of ferrocenium ion. Electrochemical impedance spectra (EIS) and cyclic voltammetry (CV) were used to evaluate the electrochemical properties of the supramolecular film. The bare gold electrode failed to distinguish the oxidation peaks of ascorbic acid (AA) and uric acid (UA) in phosphate buffer solution (PBS, pH 7.0), while the ferricinium–thioglycollate modified electrode could separate them efficiently. In differiential pulse voltammetric measurements, the prepared gold electrode could separate AA and UA signals, allowing the simultaneous determination of AA and UA. Under optimal conditions and within the linear range of 1.0 × 10⁻⁶ to 5.0 × 10⁻⁴ M, the detection limits of AA and UA achieved were 2.0 × 10⁻⁷ and 1.0 × 10⁻⁷ M, respectively. The applicability of the prepared electrode was demonstrated by measuring AA and UA in human urine without any pretreatment. Figure Fabrication process for the modified electrode     

Electrocatalytic oxidation of quinine sulfate at a multiwall carbon nanotubes-ionic liquid modified glassy carbon electrode and its electrochemical determination

The electrocatalytic oxidation of quinine sulfate (QS) was investigated at a glassy carbon electrode, modified by a gel containing multiwall carbon nanotubes (MWCNTs) and room-temperature ionic liquid of 1-Butyl-3-methylimidazolium hexafluorophate (BMIMPF₆) in 0.10 M of phosphate buffer solution (PBS, pH 6.8). It was found that an irreversible anodic oxidation peak of QS with E _pa as 0.99 V appeared at MWCNTs-RTIL/glassy carbon electrode (GCE). The electrode reaction process was a diffusion-controlled one and the electrochemical oxidation involved two electrons transferring and two protons participation. Furthermore, the charge-transfer coefficient (α), diffusion coefficient (D), and electrode reaction rate constant (k _f) of QS were found to be 0.87, 7.89 × 10⁻³ cm²⋅s⁻¹ and 3.43 × 10⁻² s⁻¹, respectively. Under optimized conditions, linear calibration curves were obtained over the QS concentration range 3.0 × 10⁻⁶ to 1.0 × 10⁻⁴ M by square wave voltammetry, and the detection limit was found to be 0.44 μM based on the signal-to-noise ratio of 3. In addition, the novel MWCNTs-RTIL/GCE was characterized by the electrochemical impedance spectroscopy and the proposed method has been successfully applied in the electrochemical quantitative determination of quinine content in commercial injection samples and the determination results could meet the requirement.     

Fabrication of gold nanoparticles/polypyrrole composite-modified electrode for sensitive hydroxylamine sensor design

A highly sensitive hydroxylamine (HA) electrochemical sensor is developed based on electrodeposition of gold nanoparticles with diameter of 8 nm on the pre-synthesized polypyrrole matrix and formed gold nanoparticles/polypyrrole (GNPs/PPy) composite on glassy carbon electrode. The electrochemical behavior and electrocatalytic activity of the composite-modified electrode are investigated. The GNPs/PPy composite exhibits a distinctly higher electrocatalytic activity for the oxidation of HA than GNPs with twofold enhancement of peak current. The enhanced electrocatalytic activity is attributed to the synergic effect of the highly dispersed gold metal particles and PPy matrix. The overall numbers of electrons involved in HA oxidation, the electron transfer coefficient, catalytic rate constant, and diffusion coefficient are investigated by chronoamperometry. The sensor presents two wide linear ranges of 4.5 × 10⁻⁷–1.2 × 10⁻³ M and 1.2 × 10⁻³–19 × 10⁻³ M with the detection limit of 4.5 × 10⁻⁸ M (s/n = 3). In addition, the proposed electrode shows excellent sensitivity, selectivity, reproducibility, and stability properties.     

Characterization and application of an electrode modified by mechanically immobilized copper hexacyanoferrate

A newly modified electrode was prepared by mechanical immobilization of copper hexacyanoferrate (CuHCF) on a graphite electrode. The modified electrode was characterized by cyclic voltammetric experiments. The effect of different background electrolytes, pHs and scan rates on the electrochemical behaviour of the electrode has been evaluated. In NH₄Cl two reversible redox peaks were observed. The first redox peak corresponding to Cu⁺/Cu²⁺ is observed only in this medium. The second redox peak corresponds to the Fe(CN)₆ ^4–/Fe(CN)₆ ^3– couple. Both anodic peaks were used for catalytic oxidation of ascorbic acid. As the anodic current for catalytic oxidation was proportional to the amount of ascorbic acid, an analytical method was developed for the determination of ascorbic acid in commercial samples. Received: 26 May 1998 / Revised: 15 March 1999 / Accepted: 20 March 1999