Preparation, characterization and photocatalytic activity of visible light driven chlorine-doped TiO2

A novel chlorine-doped titanium dioxide catalyst with visible light response was prepared by hydrolysis of tetrabutyl titanate in hydrochloric acid. The catalyst samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and ultraviolet-visible diffuse reflectance spectroscopy (UV-Vis DRS). Results showed that the doped element of Cl lowered the temperatures of phase transformation of TiO₂ from amorphous to anatase and from anatase to rutile. The absorption edge of chlorine-doped TiO₂ calcined at 300°C shifted to visible light region. X-ray photoelectron spectroscopy results proved that chlorine existed in the TiO₂ crystal lattice as anion. The photocatalytic degradation of phenol showed that under visible light (λ > 400 nm) irradiation, the chlorine-doped TiO₂ calcined at 300°C displayed the best performance, the degradation ratio of phenol was 42.5% after 120 min. Translated from Chinese Journal of Catalysis, 2006, 27(10): 890–894 [译自: 催化学报]     

金红石相TiO2纳米棒的氢化处理及其光催化活性

以钛酸四丁酯为钛源,通过盐酸调制的水热法制备出了具有棒状结构的金红石相纳米TiO₂,并进一步进行高温氢化处理. 采用X射线衍射（XRD）,透射电镜（TEM）,紫外-可见-近红外漫反射（UV-Vis-NIR DRS）,电子顺磁共振（EPR）和表面光伏（SPS）等测试手段对样品进行表征,以气相乙醛和液相苯酚为目标污染物考察催化剂的光催化活性. 结果表明：随着高温氢化处理时间的延长,TiO₂样品的可见光吸收逐渐增强,其颜色逐渐由白色转变成灰色,这主要与引入的Ti³⁺/氧空位缺陷有关. 表面光电压谱和羟基自由基测试表明,适当时间的氢化处理有利于光生电荷的分离. 在光催化氧化降解气相乙醛和液相苯酚过程中,经适当时间氢化处理的样品表现出高的可见光催化活性. 并且可见光催化活性的规律与紫外光下的是一致的. 这是因为氢化处理后在导带底下方引入了缺陷能级,拓展了可见光响应. 过度的氢化处理会在TiO₂导带下方引入较低的缺陷能级,使光生电荷的复合加剧,导致光催化活性降低.     

New synthesis of excellent visible-light TiO2−xNx photocatalyst using a very simple method

An excellent visible-light-responsive (from 400 to 550 nm) TiO_2−xN_x photocatalyst was prepared by a simple wet method. Hydrazine was used as a new nitrogen resource in this paper. Self-made amorphous titanium dioxide precursor powders were dipped into hydrazine hydrate, and calcined at low temperature (110 °C) in the air. The TiO_2−xN_x was successfully synthesized, following by spontaneous combustion. The photocatalyst was characterized by X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), transmission electron microscope (TEM), UV-Vis diffuse reflectance spectrometer (DRS), and X-ray photoelectron spectroscopy (XPS). Analysis of XPS indicated that N atoms were incorporated into the lattice of the titania crystal during the combustion of hydrazine on the surface of TiO₂. Ethylene was selected as a target pollutant under visible-light excitation to evaluate the activity of this photocatalyst. The newly prepared TiO_2−xN_x photocatalyst with strong photocatalytic activity and high photochemical stability under visible-light irradiation was firstly demonstrated in the experiment.     

金红石相TiO2-石墨烯复合材料的制备及其光催化性能

以鳞片石墨为原料, 用改进的Hummers法制备氧化石墨烯(GO), 以异丙醇钛为钛源经一步水热法制备得到金红石相TiO₂-石墨烯复合材料(rGO-TiO₂), 考察了氧化石墨烯用量对复合材料光催化性能的影响. 采用X射线衍射(XRD), 比表面积(BET), 透射电镜(TEM), 扫描电镜(SEM), 拉曼光谱, 紫外-可见(UV-Vis)吸收光谱和荧光光谱(PL)等测试手段对复合材料进行表征. 结果表明: 复合材料中TiO₂为针簇状结构的金红石相, 与石墨烯能够均匀复合; 与纯金红石相TiO₂相比, 复合材料具有较大的比表面积. 研究了该复合材料在紫外光下对罗丹明B 以及可见光下对甲基橙光降解效果. 当氧化石墨烯浓度为0.5 mg·mL^-1时, 制备得到的复合材料rGO-TiO₂具有较好的光催化效果.     

Effects of S and Ta codoping on photocatalytic activity of rutile TiO<Subscript>2</Subscript>

In this study, pure titanium dioxide (TiO₂), Ta-doped TiO₂, S-doped TiO₂, and Ta-S-codoped rutile TiO₂ photocatalysts were prepared by a sol-gel method. To evaluate the properties of the synthesized samples, X-ray diffraction analysis (XRD) and X-ray photoelectron spectroscopy (XPS) were applied. XRD detection results showed that the samples contained rutile phase basically. Scanning electron microscope observation showed that the morphology of Ta-S-TiO₂ was nearly spherical. Transmission electron microscope investigation indicated that Ta-S-TiO₂ had a flower-shaped structure consisting of many nanorods. The measurement of Brunauer-Emmett-Teller (BET)-specific surface areas (S_BET) showed that tantalum and sulfur codoping can effectively increase the S_BET of TiO₂. XPS results indicated that Ta was in the form of Ta⁵⁺ in the TiO₂ structure. Finally, the photocatalytic activities of synthesized photocatalyst samples were measured for the degradation of methylene blue in ultraviolet and visible light irradiation. The results demonstrated that the Ta-S-codoped rutile TiO₂ photocatalyst had better photocatalytic performance than pure rutile TiO₂, Ta-doped rutile TiO₂ and S-doped rutile TiO₂ photocatalyst.

Open image in new window

Effects of pure TiO₂, Ta-TiO₂, S-TiO₂, and Ta-S-TiO₂ on degradation of MB under visible light irradiation (a) and ultraviolet (UV) irradiation (b) were studied. Ta-S-TiO₂ exhibited a good photocatalytic performance under UV and visible light irradiation.

     

Boron and nitrogen-codoped TiO2 nanorods: Synthesis, characterization, and photoelectrochemical properties

Boron and nitrogen codoped TiO₂ nanorods (BNTRs) were synthesized via two-step hydrothermal reactions using TiN as a starting material. The as-prepared samples were characterized by X-ray diffraction, field-emission scanning electron microscope (SEM), transmission electron microscopy and X-ray photoelectron spectroscopy techniques. The results showed that TiO₂ nanorods with the diameter of approximately 50–100 nm and the length of several micrometers were doped by the interstitial N and B. The nanorods were firstly formed in the hydrothermal synthesis of nitrogen doped TiO₂. The growing process of nanorods was observed by SEM and a most probable formation mechanism of the trititanate nanorods was proposed. The BNTRs showed a higher photocatalytic activity and a bigger photocurrent response than N–TiO₂ nanorods under visible light irradiation.     

Building surface defects by doping with transition metal on ultrafine TiO2 to enhance the photocatalytic H2 production activity

Inefficient charge separation and limited light absorption are two critical issues associated with high-efficiency photocatalytic H₂ production using TiO₂. Surface defects within a certain concentration range in photocatalyst materials are beneficial for photocatalytic activity. In this study, surface defects (oxygen vacancies and metal cation replacement defects) were induced with a facile and effective approach by surface doping with low-cost transition metals (Co, Ni, Cu, and Mn) on ultrafine TiO₂. The obtained surface-defective TiO₂ exhibited a 3–4-fold improved activity compared to that of the original ultrafine TiO_2. In addition, a H₂ production rate of 3.4 μmol/h was obtained using visible light (λ > 420 nm) irradiation. The apparent quantum yield (AQY) at 365 nm reached 36.9% over TiO₂-Cu, significantly more than the commercial P25 TiO₂. The enhancement of photocatalytic H₂ production activity can be attributed to improved rapid charge separation efficiency and expanded light absorption window. This hydrothermal treatment with transition metal was proven to be a very facile and effective method for obtaining surface defects.     

Preparation of a visible light-driven Bi2O3–TiO2 composite photocatalyst by an ethylene glycol-assisted sol–gel method,and its photocatalytic properties

A visible light-driven Bi₂O₃–TiO₂ composite photocatalyst was prepared by an ethylene glycol-assisted sol–gel method in which ethylene glycol acted as a polycondensation agent to capture metal ions by reacting with bismuth and titanium sources via a complex polycondensation pathway. The photocatalyst was characterized by X-ray photoelectron spectroscopy, X-ray diffraction, acquisition of N₂ adsorption–desorption isotherms, transmission electron microscopy, and UV–visible diffuse reflectance spectroscopy. The results revealed that the Bi₂O₃–TiO₂ composite was of smaller particle size, greater specific surface area, and had stronger absorbance in the visible light region than pure TiO₂. The photocatalytic activity of the as-prepared catalyst was evaluated by degradation of rhodamine B under visible light irradiation (λ > 400 nm); the as-prepared Bi₂O₃–TiO₂ composite was substantially more active than pure TiO₂. This was ascribed to the high surface area and the heterojunction structure.     

Decomposition of rhodamine 6G in the presence of titania coupling coupled with carbon source as photocatalyst under visible light excitation

Heterogeneous photocatalytic degradation of N-containing R6G dye was achieved by visible light-activated carbon doped TiO₂ (C-TiO₂) nanoparticles, synthesized by a low-temperature wet-chemical technique using glucose as carbon source. The structural and physicochemical properties of C-TiO₂ were characterized by X-ray diffraction (XRD), Raman spectroscopy, UV-vis diffuse reflectance spectroscopy (UV-vis DRS) and FT-IR spectroscopy. Compared with the pure TiO₂, the carbon modified nanomaterials exhibited enhanced absorption in the broad visible-light region together with an apparent red shift in the optical absorption edge. The resulting carbon-doped TiO₂ catalyst was employed as an effective photocatalyst for degradation of Rhodamine 6G (R6G) in aqueous solutions under visible light irradiation (λ > 420 nm). In addition, the intrinsic mechanism of visible light-induced photocatalytic oxidation of organic compounds on the carbon-doped titania was proposed and discussed.     

Photocatalytic activities of C–N-doped TiO2 nanotube array/carbon nanorod composite

A C–N-doped TiO₂ nanotube (NT)/carbon nanorod composite is fabricated by chemical vapor deposition (CVD). Carbon nanorods are grown from the TiO₂ NTs, and partly graphitized, while TiO₂ is in the mixture of anatase and rutile. The C–N doping shifts the absorption edge of TiO₂ NTs to the visible light region; the formed carbon nanorods promote the charge carrier transfer from the TiO₂ surface to the electrolyte. Under the simulated solar light irradiation, the C–N-doped TiO₂ NTs show higher photocatalytic activity in the degradation of methyl orange (MO) than the undoped TiO₂ NTs.     

Photodegradation of dye pollutants on one-dimensional TiO2 nanoparticles under UV and visible irradiation

Titanium dioxides (TiO₂) nanoparticles with one-dimensional (1D) geometry, nanorods and nanostripes, were used as photocatalysts to photodegrade Rhodamine B (RhB) under ultraviolet (UV) and visible irradiation. The nanorods catalyst exhibited very interesting photocatalytic properties: under the UV irradiation its catalytic activity was slightly below that of the well-known TiO₂ catalyst P25, while under visible light it exhibited a better activity than P25.This fact indicates that the nanorods have a superior ability to utilize less energetic but more abundant visible light. Moreover, the 1D TiO₂ nanoparticles can be readily separated from aqueous suspensions by sedimentation after the reaction. With these advantages the 1D TiO₂ catalysts have a great potential for environmental applications. Various analytical techniques were employed to characterize TiO₂ catalysts and monitor the photocatalytic reaction. It was found that the catalytic performance of the catalysts is greatly dependent on their structures: The superior activity of P25 (consists of anatase and rutile nanocrystals) under UV light results probably from the interfacial interaction between anatase and rutile nanocrystals in this solid, which do not exist in the nanorods (only anatase). The titanate nanostripes (titanate) can absorb UV photons with shorter wavelength only.     

CdS/TiO2纳米管复合结构的制备与光电性能研究

利用阳极氧化法在钛金属基底表面制备一层TiO2纳米管阵列薄膜,然后通过水热反应在TiO2纳米管上负载CdS纳米粒子,形成CdS/TiO2纳米管的复合结构。利用SEM、XRD、XPS、UV-Vis等手段对其形貌和结构进行表征。进一步考察了CdS/TiO2纳米管的光电性能和光催化活性,结果表明,相比于TiO2纳米管,CdS/TiO2纳米管复合结构在紫外光和可见光下都具有更好的光催化活性及光电性能。     

Preparation and characterization of highly photoactive nanocrystalline TiO<Subscript>2</Subscript> powders by solvent evaporationinduced crystallization method

Highly photoactive bi-phase nanocrystalline TiO₂ photocatalyst was prepared by a solvent evaporation-induced crystallization (SEIC) method, and calcined at different temperatures. The obtained TiO₂ photocatalyst was characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM) and BET surface areas. The photocatalytic activity was evaluated by the photocatalytic oxidation of acetone in air. The results show that solvent evaporation can promote the crystallization and phase transformation of TiO₂ at 100°C. When calcination temperatures are below 600°C, the prepared TiO₂ powders show bimodal pore size distributions in the mesoporous region. At 700°C, the pore size distributions exhibit monomodal distribution of the inter-aggregated pores due to the collapse of the intra-aggregated pores. At 100°C, the obtained TiO₂ photocatalyst by this method shows good photocatalytic activity, and at 400°C, its photocatalytic activity exceeds that of Degussa P25. This may be attributed to the fact that the prepared TiO₂ photocatalyst has higher specific surface areas, smaller crystallite size and bimodal pore size distribution.     

Photodegradation of Direct Blue-199 in carpet industry wastewater using iron-doped TiO2 nanoparticles and regenerated photocatalyst

Fe-doped TiO_2, Ti_1–xFe_xO₂ (x = 0.00, 0.02, 0.04, 0.06, 0.08, and 0.10), photocatalysts have been successfully synthesized via citric acid–assisted autocombustion method. The synthesized photocatalysts were characterized using different characterization techniques, such as X-ray diffraction (XRD), diffuse reflectance spectroscopy (DRS), Fourier transform infrared (FT-IR), transmission electron microscopy (TEM), energy dispersive x-ray spectroscopy (EDX), and x-ray photoelectron spectroscopy (XPS). The XRD diffraction patterns revealed that synthesized photocatalysts have the anatase phase of TiO₂. The DRS analysis indicates a slight increment in absorbance in the visible light region by the Fe doping in TiO₂. The FT-IR spectra reveal the various stretching and bending vibrational bands of the Ti–O lattice. The XPS spectra confirm the presence of elements titanium, oxygen, and iron in the synthesized samples and determine binding energy of elements. TEM analysis shows the shape of the synthesized photocatalyst, and it was used to calculate the average particle sizes of undoped and Fe-doped TiO₂ (Ti_0.96Fe_0.04O₂) photocatalysts using a histogram. The photocatalytic activities of synthesized photocatalysts were determined by photodegradation of dye (Direct Blue 199), contaminating carpet industry wastewater in the photochemical reactor and open pan reactor. The maximum photodegradation activity was shown by the Ti_0.96Fe_0.04O₂ photocatalyst among all the synthesized undoped and Fe-doped photocatalysts. The synthesized photocatalyst (Ti_0.96Fe_0.04O₂) had better photocatalytic activity when compared to both, undoped TiO₂ and Aeroxide (Degussa) P-25. The used Fe-doped TiO₂ photocatalyst (Ti_0.96Fe_0.04O₂) was regenerated five times and investigated for its photocatalytic activity.     

TiO2 nanoparticles incorporated with CuInS2 clusters: preparation and photocatalytic activity for degradation of 4-nitrophenol

TiO₂ nanoparticles incorporated with CuInS₂ clusters were prepared in a solvothermal process and characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM), and energy-dispersion X-ray analysis (EDX). Compared with pure TiO₂ nanoparticles, the TiO₂ nanoparticles incorporated with CuInS₂ clusters display higher photocatalytic activity with 99.9% of degradation ratio of 4-nitrophenol after 2 h irradiation. In order to investigate the effect of the CuInS₂ clusters on the photocatalytic activity of TiO₂ nanoparticles, diffuse reflectance UV–Vis spectra (DRS), photoluminescence (PL) spectra, and photocurrent action spectra were measured. The results indicate that the enhanced photocatalytic activity is probably due to the interface between TiO₂ and CuInS₂ as a trap of the photogenerated electrons to decrease the recombination of electrons and holes.     

Hydrothermal synthesis and enhanced photocatalytic activity of mixed-phase TiO2 powders with controllable anatase/rutile ratio

In this study, mixed-phase TiO₂ powders were novelly synthesized via a facile and mild hydrothermal method without any post-heat treatment. TiOSO₄ and peroxide titanic acid (PTA) were used as inorganic titanium sources, while no special solvent or additive were introduced. The XRD and TEM results showed the mixed-phase TiO₂ powders were composed of anatase and rutile phases, and the PTA sol played an important role on forming the rutile nucleus. The proportion of rutile in the mixed-phase TiO₂ could be easily controlled in the range of 0%–70.5% by changing the amount of PTA sol used in the synthesis process. The UV-Visible absorption spectra indicated the prepared mixed-phase TiO₂ showed enhanced visible light absorption with the increase of rutile ratio. The photodegradation experiments revealed the mixed-phase TiO₂ exhibited the best photocatalytic activity at the rutile ratio of 41.5%, while a higher or lower rutile ratio both resulted in the decrease of photocatalytic activity.     

Ag@AgI等离子体负载TiO2酸蚀纳米带的制备及可见光光催化性能的研究

采用沉积-沉淀法将AgI分散到TiO2酸蚀纳米带上,然后通过光照进而分解出Ag颗粒,最终获得了Ag@AgI等离子体负载的TiO2酸蚀纳米带(AIST)。利用UV-Vis吸收光谱、XRD、SEM对产物进行表征,并研究了可见光下对甲基橙(MO)的光催化降解性能。结果表明,纳米带酸蚀后利于AgI的沉积,Ag的表面等离子体共振效应可以增强催化剂对于可见光的吸收,使可见光下AIST的光催化降解性能显著提高。     

Photocatalytic degradation of methylene blue on Fe3+-doped TiO2 nanoparticles under visible light irradiation

Fe³⁺-doped TiO₂ composite nanoparticles with different doping amounts were successfully synthesized using sol-gel method and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and ultravioletvisible spectroscopy (UV-Vis) diffuse reflectance spectra (DRS). The photocatalytic degradation of methylene blue was used as a model reaction to evaluate the photocatalytic activity of Fe³⁺/TiO₂ nanoparticles under visible light irradiation. The influence of doping amount of Fe³⁺ (ω: 0.00%–3.00%) on photocatalytic activities of TiO₂ was investigated. Results show that the size of Fe³⁺/TiO₂ particles decreases with the increase of the amount of Fe³⁺ and their absorption spectra are broaden and absorption intensities are also increased. Doping Fe³⁺ can control the conversion of TiO₂ from anatase to rutile. The doping amount of Fe³⁺ remarkably affects the activity of the catalyst, and the optimum efficiency occurs at about the doping amount of 0.3%. The appropriate doping of Fe³⁺ can markedly increase the catalytic activity of TiO₂ under visible light irradiation. __________ Translated from Journal of Northwest Normal University (Natural Science), 2006, 42(6): 55–56 [译自: 西北师范大学学报(自然科学版)]     

Doping level effect on visible-light irradiation W-doped TiO2–anatase photocatalysts for Congo red photodegradation

A series of W-modified TiO₂ (W–TiO₂) photocatalysts were synthesized by a simple sol–gel method. The new photocatalysts were characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV–vis-diffuse reflectance spectroscopy (DRS), and Brunauer, Emmett and Teller (BET) surface area analyzer. The photoactivity of the W–TiO₂ photocatalysts was evaluated by the photocatalytic oxidation of Congo red (CR) dye. It was found that the average size of the prepared photocatalysts is 10 nm. Moreover, they have high surface areas (∼ 216 m² g⁻¹) and their light-absorption extends to the visible region compared to pure TiO₂. The effects of W-loading and of the calcination temperature of the prepared photocatalysts on their photocatalytic activity were also studied. The obtained results show that the W_0.5–TiO₂ photocatalyst calcined at 350 °C is much highly photoactive than non-doped or highly doped TiO₂. The enhanced photocatalytic activity of the weakly doped TiO₂ may be attributed to the increase in the charge separation efficiency and the presence of surface acidity on the W_0.5–TiO₂ photocatalyst.     

二氧化钛与针铁矿复合光催化材料的制备与光催化性能

以四氯化钛为钛源,针铁矿(α-FeOOH)为载体,采用水解沉淀法制备了金红石相二氧化钛(Ti₂O)与α-FeOOH的复合光催化材料,并采用X射线衍射、扫描电子显微镜、透射电子显微镜、X射线能量散射谱和X射线光电子能谱对样品进行了表征.结果表明,低温下,金红石相Ti₂O包覆于α-FeOOH表面,并形成复合结构;较高温下,铁离子进入金红石相Ti₂O晶格,并形成铁掺杂金红石相Ti₂O纳米管;中温下,样品兼有复合和掺杂两者特征.在室温下以甲基橙为降解对象,采用钨灯+氘灯(波长200~800nm)为光源,对样品的光催化活性进行了测试.结果表明,样品对甲基橙的光催化降解效果良好;与纯α-FeOOH和金红石相Ti₂O相比,不同结构样品的光催化活性均有所提高,其中,复合兼掺杂型样品的光催化活性最高.由此可见,与α-FeOOH复合和铁掺杂是提高Ti₂O光催化活性的有效途径.