Enhanced electrochemical performance of straw-based porous carbon fibers for supercapacitor

The efficient utilization of natural biomass as renewable raw materials is of importance. We herein prepared porous carbon fibers (PCFs) by activation of the extracted cellulose microfibers from the agriculture byproduct of corn straw. Different from the porous carbons (PCs) by directly activating straw, the obtained PCFs had typical one-dimensional morphology with high surface area (2013 m² g^?1) and large pore volume (1.27 cm³ g^?1). The influence of the ZnCl₂/cellulose mass ratio on the electrochemical performance was studied, and the optimized PCF(1:1) possessed a much higher specific capacitance than the PC(1:1) sample, which was attributed to the improved specific surface area as well as the fiber-like morphology where it had short ion diffusion route and small interfacial resistance in comparison to PCs. PCFs have a high specific capacitance of 230 F g^?1 at 0.5 A g^?1, and 183 F g^?1 was retained at 20 A g^?1 (79.6%), revealing an excellent rate capability. The assembled symmetrical supercapacitor exhibited a wide potential window of 1.8 V, small electrochemical impedance, and superior cycle performance. Moreover, a high energy density of 16.0 Wh kg^?1 was obtained at a power density of 450.4 W kg^?1, which was preserved of 6.9 Wh kg^?1 at a high power density of 14,194.3 W kg^?1.     

Facile preparation of nitrogen-doped porous carbon for high performance symmetric supercapacitor

In this work, the micromolecule l-glutamic acid (Glu) is employed as nitrogen-rich precursor to prepare a novel porous carbon, and ZnCl₂ is used as activating agent to improve the surface area and electrochemical performance of the carbon. The nitrogen content of the carbon (Glu-2.5) prepared by Glu and ZnCl₂ with a mass ratio of 1:2.5 retains as high as 7.1 % at an activation temperature of 700 °C. The surface area and pore volume of Glu-2.5 are 1007.4 m² g^?1 and 0.57 cm³ g^?1, respectively. Glu-2.5 exhibits a high specific capacitance of 330.6 F g^?1 in 2 M KOH electrolyte at the current density of 1 A g^?1and good cycling stability (89 % retention of capacitance after 5000 charge/discharge cycles). More importantly, the assembled symmetric supercapacitor using Glu-2.5 as electrodes reveals a high energy density (16.7 Wh kg^?1) under the power density of 404.7 W kg^?1. Owing to its inherent advantages, Glu-2.5 could be a promising and scalable alternative applied to energy storage/conversion.     

KOH direct treatment of kombucha and in situ activation to prepare hierarchical porous carbon for high-performance supercapacitor electrodes

Kombucha, a renewable biomass, has been successfully utilized as an accessible carbon source to fabricate kombucha-derived hierarchical porous carbon (KHPC) by KOH direct treatment and in situ activation. The prepared KHPC shows an interconnected hierarchical porous structure, a pore volume of 0.41 cm³ g^?1, and a specific surface area of 917 m² g^?1. Due to the multiple synergistic effects of these advantages, the KHPC-3 exhibits a high specific capacitance of 326 F g^?1 at a current density of 1 A g^?1 in 6 M KOH, good rate capability of 82% retention from 1 to 20 A g^?1, and cycling performance with 91.3% retention over 5000 cycles. Moreover, the KHPC-3 symmetric supercapacitor reveals a good energy density of 20.97 Wh kg^?1 at a power density of 871.2 W kg^?1 and retains 8.08 Wh kg^?1 at 6330 W kg^?1 in 1 M Na₂SO₄ electrolyte. Therefore, the KHPC obtained via the simple synthesis process shows great promise as an electrode material in energy storage devices.     

Facile synthesis of biomass-derived hierarchical porous carbon microbeads for supercapacitors

Using the facile method of solvent evaporation, the leonardite fulvic acids (LFA)-based porous carbon microbeads (PCM) have been successfully prepared at ambient pressure, followed by carbonization and KOH activation (a low mass ratio alkali/LFA = 1.5) in an inert atmosphere. The effects of KOH treatment on pore structures and the formation mechanism of the PCM were discussed. The results showed that the sample exhibited remarkable improvement in textural properties. The activated carbon microbeads had high surface area (2269 m² g^?1), large pore volume (1.97 cm³ g^?1), and displayed excellent capacitive performances, compared with carbon powder. The porous carbon material electrodes with the “porous core structure” behaved superiorly at a specific capacitance of 320 F g^?1 at a current density of 0.05 A g^?1 in 6 M KOH electrolyte, which could still remain 193 F g^?1 when the current density increased to 100 A g^?1. Remarkably, in the 1 M TEABF₄/PC electrolyte, the PCM samples could reach 156 F g^?1 at 0.05 A g^?1, possess an outstanding energy density of 39.50 Wh kg^?1, and maintain at 22.05 Wh kg^?1 even when the power density rose up to 5880 W kg^?1. The balance of structural characteristic and high performance makes the porous carbon microbeads a competitive and promising supercapacitor electrode material.     

Electrospun porous MnMoO<Subscript>4</Subscript> nanotubes as high-performance electrodes for asymmetric supercapacitors

MnMoO₄ nanotubes of diameter about 120 nm were successfully synthesized by a single-spinneret electrospinning technique followed by calcination in air, and their structural, morphological, and electrochemical properties were studied with the aim to fabricate high-performance supercapacitor devices. The obtained MnMoO₄ nanotubes display a 1D architecture with a porous structure and hollow interiors. Benefiting from intriguing structural features, the unique MnMoO₄ nanotube electrodes exhibit a high specific capacitance, excellent rate capability, and cycling stability. As an example, the tube-like MnMoO₄ delivers a specific capacitance of 620 F g^?1 at a current density of 1 A g^?1, and 460 F g^?1 even at a very high current density of 60 A g^?1. Remarkably, almost no decay in specific capacitance is found after continuous charge/discharge cycling for 10,000 cycles at 1 A g^?1. An asymmetric supercapacitor fabricated from this MnMoO₄ nanotubes and activated carbon displayed a maximum high energy density of 31.7 Wh kg^?1 and a power density of 797 W kg^?1, demonstrating a good prospect for practical applications in energy storage electronics.     

In situ synthesis of crosslinked-polyaniline nano-pillar arrays/reduced graphene oxide nanocomposites for supercapacitors

Crosslinked-polyaniline (CPA) nano-pillar arrays adsorbed on the surface of reduced graphene oxide (RGO) sheets were synthesized by in situ solution polymerization through two steps of reduction. The electrochemical analyses demonstrated that the befittingly reduced CPA/RGO composite exhibited high performance as electrode materials for supercapacitors. The CPA/RGO composite showed very high specific capacitance of 1532 F g^?1 at a scan rate of 10 mV s^?1 or 694 F g^?1 at a current density of 2 A g^?1 in 1 M H₂SO₄ electrolyte, as well as great energy density of 61.4 W h kg^?1 at a current density of 2 A g^?1. The electrode material also had decent power density of 4 kW kg^?1 at a current density of 10 A g^?1, and good cycling stability of 92.5 % capacitance retained after 500 cycles of cyclic voltammetry at 500 mV s^?1. The neat microstructures and super electrochemical properties suggest the potential use of the composites in supercapacitors.     

Binder-free activated carbon papers for high-performance electric double-layer capacitors

A binder-free activated carbon paper (ACP) was simply prepared for electric double-layer capacitors by the carbonization of filter paper, followed by heat-air activation at a lower temperature. The electrochemical cells assembled using the as-prepared ACP-470 provides a high specific capacitance of 296.4 F g^?1 at current density of 0.5 A g^?1 and a high rate performance at a current density of 150 A g^?1 with a capacitance of 191.2 F g^?1 and a high cycle ability at 10,000 recycles with 100 % capacitance retention. In addition, the ACP has a lower electrical resistivity and provides an effective energy storage performance with a maximum energy density of 41.2 Wh kg^?1 and a maximum power density of 138.0 kW kg^?1 in a voltage range of 1 V.     

Converting eucalyptus leaves into mesoporous carbon for its application in quasi solid-state supercapacitors

A high performance activated carbon having pore diameter of 2.8 nm and specific surface area of 841.8 m² g^?1 is prepared by chemical activation of eucalyptus leaves using KOH as an activating agent. The chemically-treated eucalyptus leaves EL(T) as electrode material has a specific capacitance of 663.5 mF cm^?2 (equivalent to single electrode specific capacitance of 442.3 F g^?1) with solid polymer electrolyte. This active material has excellent rate capability and good cycle performance, over 95 % of the original capacitance is retained after 5,000 cycles. The energy density of 101.6 Wh kg^?1 and power density of 2.85 kW kg^?1 has been observed for EL(T) based quasi solid-state supercapacitors.     

A high-performance hybrid supercapacitor with Li4Ti5O12-C nano-composite prepared by in situ and ex situ carbon modification

In this work, we report on the synthesis of in situ and ex situ carbon-modified Li₄Ti₅O₁₂-C (LTO-C) nano-composite and its application in a hybrid supercapacitor constructed using activated carbon (AC) and LTO-C nano-composite as positive and negative electrodes, respectively. The hybrid capacitors are characterized by galvanostatic charge–discharge, cycle life testing, and electrochemical impedance spectroscopy. The results reveal that the AC/LTO-C hybrid capacitors exhibit high rate capability and long cycle life. In the potential range of 1.5–3.0 V, the AC/LTO-C hybrid system can deliver a specific capacitance of 83 F?g^?1 based on the total mass of AC and LTO-C electrodes at a current density of 60 mA g^?1 (2 C rate). At a higher discharge rate of 980 mA g^?1 (32 C), the capacity is 68 F?g^?1, about 82?% of that at 2 C rate. After 9,000 deep cycles at 32 C, the hybrid capacitor still maintains 84?% of its initial capacitance. The specific energy of such hybrid system is 20 Wh kg^?1, which is at least twice that of an AC/AC system. Combining the high energy density with power capability, the AC/LTO-C hybrid supercapacitor has demonstrated high performance for applications needing high power output.     

The production of activated carbon from cation exchange resin for high-performance supercapacitor

High-performance activated carbon for electrochemical double-layer capacitors (EDLC) has been prepared from cation exchange resin by carbonization and subsequent activation with KOH. The activation temperature has a key role in the determination of porous carbon possessing high surface areas, and large pore structures. The porous carbon activated at 700 °C (carbon-700-1:4) has high surface area (2236 m²?g^?1) and large total pore volume (1.15 cm³?g^?1), which also displays best capacitive performances due to its well-balanced micro- or mesoporosity distribution. In details, specific capacitances of the carbon-700-1:4 sample are 336.5 F?g^?1 at a current density of 1 A?g^?1 and 331.8 F?g^?1 at 2 A?g^?1. At high current density as 20 A?g^?1, the retention of its specific capacitance is 68.4 %. The carbon-700-1:4 sample also exhibits high performance of energy density (46.7 Wh?kg^?1) and long cycle stability (～8.9 % loss after 3,000 cycles). More importantly, due to the amount of waste ion-exchange resins increasing all over the world, the present synthetic method might be adopted to dispose them, producing high-performance porous carbons for EDLC electrode materials.     

A high mass loading electrode based on ultrathin Co<Subscript>3</Subscript>S<Subscript>4</Subscript> nanosheets for high performance supercapacitor

There is a growing need for the electrode with high mass loading of active materials, where both high energy and high power densities are required, in current and near-future applications of supercapacitor. Here, an ultrathin Co₃S₄ nanosheet decorated electrode (denoted as Co₃S₄/NF) with mass loading of 6 mg cm^?2 is successfully fabricated by using highly dispersive Co₃O₄ nanowires on Ni foam (NF) as template. The nanosheets contained lots of about 3～5 nm micropores benefiting for the electrochemical reaction and assembled into a three-dimensional, honeycomb-like network with 0.5～1 μm mesopore structure for promoting specific surface area of electrode. The improved electrochemical performance was achieved, including an excellent cycliability of 10,000 cycles at 10 A g^?1 and large specific capacitances of 2415 and 1152 F g^?1 at 1 and 20 A g^?1, respectively. Impressively, the asymmetric supercapacitor assembled with the activated carbon (AC) and Co₃S₄/NF electrode exhibits a high energy density of 79 Wh kg^?1 at a power density of 151 W kg^?1, a high power density of 3000 W kg^?1 at energy density of 30 Wh kg^?1 and 73 % retention of the initial capacitance after 10,000 charge-discharge cycles at 2 A g^?1. More importantly, the formation process of the ultrathin Co₃S₄ nanosheets upon reaction time is investigated, which is benefited from the gradual infiltration of sulfide ions and the template function of ultrafine Co₃O₄ nanowires in the anion-exchange reaction.

Open image in new window

Graphical abstract The ultrathin 2D Co₃S₄ nanosheets fabricated on 3D Ni foam and the formation process of the ultrathin Co₃S₄ nanosheets upon reaction times has been investigated. At the same time, the Co₃S₄/NF electrode displays an outstanding specific capacitance of 2420 F g^?1 at 1 A g^?1 with high mass loading of 6 mg cm^?2.

     

MnO2 Nanosheets Grown on Nitrogen‐Doped Hollow Carbon Shells as a High‐Performance Electrode for Asymmetric Supercapacitors

A hierarchical hollow hybrid composite, namely, MnO₂ nanosheets grown on nitrogen‐doped hollow carbon shells (NHCSs@MnO₂), was synthesized by a facile in situ growth process followed by calcination. The composite has a high surface area (251 m²g^?1) and mesopores (4.5 nm in diameter), which can efficiently facilitate transport during electrochemical cycling. Owing to the synergistic effect of NHCSs and MnO₂, the composite shows a high specific capacitance of 306 F g^?1, good rate capability, and an excellent cycling stability of 95.2 % after 5000 cycles at a high current density of 8 A g^?1. More importantly, an asymmetric supercapacitor (ASC) assembled by using NHCSs@MnO₂ and activated carbon as the positive and negative electrodes exhibits high specific capacitance (105.5 F g^?1 at 0.5 A g^?1 and 78.5 F g^?1 at 10 A g^?1) with excellent rate capability, achieves a maximum energy density of 43.9 Wh kg^?1 at a power density of 408 W kg^?1, and has high stability, whereby the ASC retains 81.4 % of its initial capacitance at a current density of 5 A g^?1 after 4000 cycles. Therefore, the NHCSs@MnO₂ electrode material is a promising candidate for future energy‐storage systems.     

Nitrogen-containing nanoporous carbons by a rational template carbonization method evinced in the cases of 1, 10-phenanthroline and benzimidazole

We demonstrate a rational template carbonization method to produce nitrogen-containing nanoporous carbons at 800 °C, using 1, 10-phenanthroline (or benzimidazole) as carbon/nitrogen source and magnesium citrate as template. The mass ratio of 1, 10-phenanthroline (or benzimidazole) and magnesium citrate has exerted the vital role in the determination of pore structures and the resulting electrochemical performances. It reveals that the carbon-P:Mg-1:1 (obtained by heating 1, 10-phenanthroline and magnesium citrate at 800 °C with the mass ratio of 1:1) and carbon-B:Mg-1:1 (obtained by heating benzimidazole and magnesium citrate at 800 °C with the mass ratio of 1:1) samples both are amorphous, nitrogen-containing, and highly nanoporous in nature. The carbon-P:Mg-1:1 sample has a large BET surface area of 1,657.4 m² g^?1 and high pore volume of 1.83 cm³ g^?1, and those of carbon-B:Mg-1:1 sample are of 1,105.4 m² g^?1 and 1.67 cm³ g^?1, respectively. Based on a three-electrode system using a 6-mol L^?1 KOH aqueous solution as electrolyte, the carbon-P:Mg-1:1 and carbon-B:Mg-1:1 samples can deliver large specific capacitances of 289.0 and 255.6 F g^?1 at a current density of 0.5 A g^?1. They can also exhibit high energy densities of 40.1 and 35.5 Wh kg^?1 when designated the power density as 0.25 kW kg^?1 as well as highly long-term cycling durabilities.     

Sucrose assisted hydrothermal synthesis of SnO2/graphene nanocomposites with improved lithium storage properties

SnO₂/graphene nanocomposites are synthesized by a new hydrothermal treatment strategy under the assistance of sucrose. From the images of the scanning electron microscope (SEM) and transmission electron microscope (TEM), it can be observed that SnO₂ nanoparticles with the size of 4~5 nm uniformly distribute on the graphene nanosheets. The result demonstrates that sucrose can effectively prevent graphene nanosheets from restacking during hydrothermal treatment and subsequently treatment. The charging/discharging test result indicates that the SnO₂/graphene nanocomposites exhibit high specific capacity and excellent cycleability. The first reversible specific capacity is 729 mAh.g^?1 at the current density of 50 mA.g^?1, and remains 646 mAh.g^?1 after 30 cycles at the current density of 100 mA.g^?1, 30 cycles at the current density of 200 mA.g^?1, 30 cycles at the current density of 400 mA.g^?1, 30 cycles at the current density of 800 mA.g^?1, and 30 cycles at the current density of 50 mA.g^?1.     

Preparation of activated carbon from waste Camellia oleifera shell for supercapacitor application

The cost-effective activated carbons derived from waste Camellia oleifera shell (COS) by ZnCl₂ activation method are investigated as the active electrode material in electric double-layer capacitors (EDLCs) for the first time. The activation temperature and ZnCl₂/COS impregnation ratio are two key factors affecting the surface area and pore structure of the prepared activated carbons, which accordingly affect their capacitive performances. Electrochemical investigations indicate that the activated carbon (AC-3-600) obtained at the activation temperature of 600 °C and impregnation ratio of 3 shows the maximum specific capacitance of 374 and 266 F?g^?1 in 1 mol L^?1 H₂SO₄ and 6 mol L^?1 KOH electrolytes at 0.2 A g^?1, respectively. The high capacitance of the AC-3-600 is attributed to its high surface area (1,935 m² g^?1), high total pore volume (1.02 cm³ g^?1), and especially the large percentage of micropores (735 m² g^?1). Meanwhile, the activated carbon presents good cycle stability in both acid and alkaline electrolytes during 5,000 cycles at a fair current density of 4 A g^?1. So, we had reasons to believe that the activated carbons from waste COS by ZnCl₂ activation might be one of the innovative carbon electrode materials for EDLCs application.     

Mesopore-dominant porous carbon derived from bio-tars as an electrode material for high-performance supercapacitors

For the first time, toxic bio-tars collected from the gasification of pine sawdust are used as the precursor for activated carbons. Various types of activation agents including KOH, K₂CO₃, H₃PO₄ and ZnCl₂ were screened for obtaining superior activated carbons. When KOH was used as an activation agent, the obtained activated carbons exhibited high specific surface area and large mesopore volume. The activated carbons were further employed to be the electrode material of supercapacitors, and its specific capacitance reached up to 260 F g^?1 at 0.25 A g^?1 current density. Also, it showed an excellent rate performance from preserving a relatively high specific capacitance of 151 F g^?1 at 50 A g^?1. The assembled device also exhibited the good electrochemical stability with the capacity retention of 90% after 5000 cycles. Furthermore, the maximum energy density of the activated carbons in organic electrolyte reached 17.8 Wh kg^?1.     

Design of Advanced MnO/N‐Gr 3D Walls through Polymer Cross‐Linking for High‐Performance Supercapacitor

Three‐dimensional, vertically aligned MnO/nitrogen‐doped graphene (3D MnO/N‐Gr) walls were prepared through facile solution‐phase synthesis followed by thermal treatment. Polyvinylpyrrolidone (PVP) was strategically added to generate cross‐links to simultaneously form 3D wall structures and to incorporate nitrogen atoms into the graphene network. The unique wall features of the as‐prepared 3D MnO/N‐Gr hybirdes provide a large surface area (91.516 m² g^?1) and allow for rapid diffusion of the ion electrolyte, resulting in a high specific capacitance of 378 F g^?1 at 0.25 A g^?1 and an excellent charge/discharge stability (93.7 % capacity retention after 8000 cycles) in aqueous 1 m Na₂SO₄ solution as electrolyte. Moreover, the symmetric supercapacitors that were rationally designed by using 3D MnO/N‐Gr hybrids exhibit outstanding electrochemical performance in an organic electrolyte with an energy density of 90.6 Wh kg^?1 and a power density of 437.5 W kg^?1.     

Facile fabrication of mesoporous manganese oxides as advanced electrode materials for supercapacitors

Mesoporous manganese oxides (MnO₂) were synthesized via a facile chemical deposition strategy. Three kinds of basic precipitants including sodium carbonate (Na₂CO₃), sodium bicarbonate (NaHCO₃), and sodium hydroxide (NaOH) were employed to adjust the microstructures and surface morphologies of MnO₂ materials. The obtained MnO₂ materials display different microstructures. Great differences are observed in their specific surface area and porosity properties. The microstructures and surface morphologies characteristics of MnO₂ materials largely determine their pseudocapacitive behavior for supercapacitors. The MnO₂ prepared with Na₂CO₃ precipitant exhibits the optimal microstructures and surface morphologies compared with the other two samples, contributing to their best electrochemical performances for supercapacitors when conducted either in the single electrode tests or in the capacitor measurements. The optimal MnO₂ electrode exhibits a high specific capacitance (173 F g^–1 at 0.25 A g^?1), high-rate capability (123 F g^?1 at 4 A g^?1), and excellent cyclic stability (no capacitance loss after 5,000 cycles at 1 A g^?1). The optimal activated carbon//MnO₂ hybrid capacitor exhibits a wide working voltage (1.8 V), high-power and high-energy densities (1,734 W kg^?1 and 20.9 Wh kg^?1), and excellent cycling behavior (93.8 % capacitance retention after 10,000 cycles at 1 A g^?1), indicating the promising applications of the easily fabricated mesoporous MnO₂ for supercapacitors.     

Co(OH)2/graphene sheet-on-sheet hybrid as high-performance electrochemical pseudocapacitor electrodes

A Co(OH)₂/graphene sheet-on-sheet hybrid has been fabricated by in situ one-step hydrothermal growth for electrochemical pseudocapacitors application. The hybrid delivers a specific capacitance of 436 F?g^?1 at a current density of 50 A?g^?1. Besides, it can keep a specific capacitance of 651 F?g^?1 after 10,000 cycles at 10 A?g^?1. The excellent performance can be ascribed to the high-quality graphene matrix, regular morphology and high crystallinity of Co(OH)₂, and unique sheet-on-sheet structure of the hybrid, endowing enhanced transportation of electrons and Faradic redox reactions. The results demonstrate that the Co(OH)₂/graphene hybrid with a sheet-on-sheet structure is promising for high-performance energy storage applications.     

Preparation,characterization, and evaluation of LiNi0.4Co0.6O2 nanofibers for supercapacitor applications

We prepared LiNi_0.4Co_0.6O₂ nanofibers by electrospinning at the calcination temperature of 450 °C for 6 h. The prepared LiNi_0.4Co_0.6O₂ nanofibers was characterized by thermal, X-ray diffraction, and Fourier transform infrared (FTIR) studies. The morphology of LiNi_0.4Co_0.6O₂ nanofibers was characterized by scanning electron microscopy studies. The asymmetric supercapacitor was fabricated using LiNi_0.4Co_0.6O₂ nanofibers as positive electrode and activated carbon (AC) as negative electrode and a porous polypropylene separator in 1 M LiPF₆–ethylene carbonate/dimethyl carbonate (LiPF₆–EC:DMC) (1:1?v/v) as electrolyte. Cyclic voltammetry studies were then carried out in the potential range of 0 to 3.0 V at different scan rates which exhibited the highest specific capacitance of 72.9 F g^?1. The electrochemical impedance measurements were carried out to find the charge transfer resistance and specific capacitance of the cell, and they were found to be 5.05 Ω and 67.4 F g^?1, respectively. Finally, the charge–discharge studies were carried out at a current density of 1 mA cm^?2 to find out the discharge-specific capacitance, energy density, and power density of the capacitor cell, and they were found to be 70.9 F g^?1, 180.2 Wh kg^?1, and 248.0 W kg^?1, respectively.