Comparative study of pulsed laser diode end-pumped thulium-doped 2-µm Q-switched lasers

We report pulsed laser diode(LD)end-pumped acoustic Q-switched Tm:YAG laser,Tm:LuAG laser,and Tm:LuYAG laser and the physical properties and spectra of Tm:YAG,Tm:LuAG,and Tm:LuYAG are analyzed.The Tm:LuYAG laser is pumped by 785-nm and 788-nm pulses separately,and is compared with Tm:YAG laser.Different output energy values and output wavelengths of Tm:LuAYG lasers pumped by LDs with different wavelengths are obtained and compared with each other.When the repetition frequency is 100 Hz,the pulsed Tm:YAG laser has single pulse energy of 15.9 mJ,pulse width of 126.7 ns,and the center wavelength of 2013.36 nm,and the pulsed Tm:LuAG laser possesses single pulse energy of 11.8 mJ,pulse width of 252.4 ns,and the center wavelength of 2023.65 nm,and the pulsed Tm:LuYAG laser output energy values are 12.32 mJ and 12.25 mJ with the slope efficiencies of 12.5%and 11.85%,the center wavelengths of 2017.89 nm and 2027.11 nm,respectively,while the pump sources are 785-nm and 788-nm pulsed LDs,respectively.     

Laser on nitrogen-electronegative gas mixtures, pumped by inductive energy storage generator: Experiment and theoretical model

The advantages of inductive energy storage (IES) generators for increasing the pulse energy, power, and duration for nitrogen laser pumped by self-sustained transverse discharge have been experimentally demonstrated. A theoretical model is developed and the operation of IES-pumped laser on nitrogen-electronegative gas mixtures is numerically simulated. It is shown experimentally and theoretically that, adding electronegative gases, one can control the pulse shape of lasing on the C³II _u -B³II _g transition in nitrogen. The increase in the electric field strength in the laser gap in N₂-NF₃ and N₂-SF₆ mixtures produced 337.1-nm laser pulses consisting of two spaced peaks and 40–50-ns pulses close to rectangular. The increase in the laser active volume to 6 l (discharge cross section to 6×10 cm²) in N₂–SF₆ mixtures made it possible to obtain the maximum output energy (Q=110 mJ) and UV power (P _las =6 MW). In N₂-NF₃ mixtures, the laser pulse duration was up to ∼100 ns with an energy up to Q=30 mJ.     

A powerful diode-pumped laser source for micro-machining with ps pulses in the infrared, the visible and the ultraviolet

We report a ps diode-pumped Nd:YVO₄ laser system for micro-machining applications. The system consists of a passively mode-locked oscillator followed by a regenerative amplifier. It provides laser pulses at 1064 nm with a pulse duration of 10.2 ps, a repetition rate of 20 kHz and an average output power of 10.8 W. This average power corresponds to a pulse energy of 0.54 mJ. Second-harmonic generation in LBO and fourth-harmonic generation in BBO provide visible (532-nm) and ultraviolet (266-nm) radiation with pulse energies of 270 J and 75 J, respectively. Amplification in a diode-pumped single-pass Nd:YVO₄ amplifier increases the pulse energy of the fundamental 1064-nm laser pulses to 1 mJ. PACS 42.55.Xi; 42.60.Da; 42.65.Ky; 42.65.Re     

Influence of storage time on laser cleaning of SiO<Subscript>2</Subscript> on Si

The influence of the ‘storage time’ τ_s on the threshold fluence φ_cl and the efficiency in dry laser cleaning is investigated. τ_s denotes the time between the deposition of particles and the cleaning. As a model system we employed silica spheres with diameters of 500 nm and 1500 nm on commercial silicon wafers and single-pulse KrF excimer laser radiation (τ_FWHM=28 ns). For the 1500-nm silica spheres, φ_cl was found to increase from about 65 mJ/cm² to 125 mJ/cm² for storage times of 4 h and 362 h, respectively. For 500-nm silica spheres the increase in the threshold fluence was less than 20% for storage times up to 386 h. Received: 12 July 2002 / Accepted: 12 July 2002 / Published online: 29 January 2003 RID="*" ID="*"Corresponding author. E-mail:dieter.baeurle@jku.at     

532 nm laser based on V-type doubly resonant intra-cavity frequency-doubling

LD side-pumped dual interconnected V-type quasi-continuous wave green laser has been demonstrated. The two Nd:YAG modules were placed in a plane-concave V-type resonator and a plane-concave straight cavity formed two stable operation beam of the 1064-nm fundamental frequency laser. Through acousto-optic Q-switched and frequency doubling crystal, two double-frequency laser beams arrived at the folded flat mirror, which were unidirectional output by the folded flat mirror at the end. As the pumped current was 50 A, the 532 nm green laser maximum average output power of 206 W at a repetition of 22.4 kHz was achieved with a pulse width of 201 ns and the largest single pulse energy of 9.2 mJ, corresponding to a peak power of 45.8 kW and a double frequency efficiency of 60.2%.     

Injection-Seeded 500 Hz Repetition Rate High Peak Power Single-Frequency Nd:YAG Laser for Mid-Infrared Generation

We develop an injection-seeded single-frequency neodymium-doped yttrium aluminum garnet (Nd:YAG) laser with 500 Hz repetition rate and high peak power. The laser construction is designed as seed injection and master oscillator power amplifier (MOPA) including single-frequency master oscillator, extra-cavity frequency doubling crystal, and round-trip power amplifier. The master oscillator can emit 1,064 nm laser of 8.4 mJ with 6.8 ns pulse width at the pump energy equal to 23 mJ. A green laser energy of 1.1 mJ is obtained by setting the proper temperature of the LBO crystal. The pulse energy of 1,064 nm laser decreases to 6.5 mJ after passing through the LBO crystal and rises to 25.3 mJ after a round-trip power amplifier corresponding to the extraction efficiency of 29%. The final output pulse width is 6.5 ns, representing a peak power of 3.9 MW. The 1,064 nm laser beam quality factor M² of the master oscillator and the amplified one are 1.3 and 1.5, respectively. The laser will be used to generate mid-infrared where the 532 nm laser with narrow pulse width is to pump sheet optical parametric oscillator (OPO) and the 1,064 nm laser with high peak power to pump the OPO.     

High-power parametric amplification of 11.8-fs laser pulses with carrier-envelope phase control

Phase-stable parametric chirped-pulse amplification of ultrashort pulses from a carrier-envelope phase-stabilized mode-locked Ti:sapphire oscillator (11.0 fs) to 0.25 mJ/pulse at 1 kHz is demonstrated. Compression with a grating compressor and a LCD shaper yields near-Fourier-limited 11.8-fs pulses with an energy of 0.12 mJ. The amplifier is pumped by 532-nm pulses from a synchronized mode-locked laser, Nd:YAG amplifier system. This approach is shown to be promising for the next generation of ultrafast amplifiers aimed at producing terawatt-level phase-controlled few-cycle laser pulses.     

Co:LaMgAl11O19 saturable absorber Q-switch for a 1.319 μm Nd:YAG laser

Passively Q-switched output of a flashlamp-pumped 1.319 μm Nd:YAG laser is realized by using Co²⁺:LaMgAl₁₁O₁₉ (Co:LMA) as saturable absorber. When initial transmission of the saturable absorber T₀ is 78%, a Q-switched output pulse with pulse width (FWHM) 44.8 ns and pulse energy 17.4 mJ is obtained, corresponding to 19.3% of the free-running energy under the equal pumping energy of 45.4 J. The experimental results show that the higher T₀ will result in a lower pumping threshold of the laser, but lower T₀ can make the laser generate pulses with higher single-pulse energy, narrower pulse width, and accordingly higher peak power.     

High-brightness optical-field-ionization collisional-excitation extreme-ultraviolet lasing pumped by a 100-TW laser system in an optically preformed plasma waveguide

Recent study on optical-field-ionization collisional-excitation extreme-ultraviolet lasing of Ni-like krypton at 32.8 nm pumped by a 100-TW laser system with an optically preformed plasma waveguide is reported. By using a 9-mm-long pure krypton plasma waveguide fabricated with the axicon-ignitor-heater scheme, the 32.8-nm extreme-ultraviolet laser provided an average output of 10¹² photons/pulse at pump energy of 1 J, more than one order of magnitude enhancement relative to the previous results with the same scheme at pump energy of 235 mJ. It is also found the far-field pattern of laser beams varies from a single peak profile at low pump energy to an annular profile at high pump energy due to over-ionization of krypton ions at the center of the plasma channel.     

High repetition rate, tunable, Q-switched diode pumped Tm:YLF laser

The aim of work was to characterize a simple oscillator consisted of Tm:YLF crystal end-pumped by a fiber coupled diode laser and active Q-switch with tunability option. About 7 W with near 35% slope efficiency was demonstrated in a free-running mode. The divergence angle was about 4.3 mrad and estimated parameter M² < 1.3. Continuous tuning by means of Lyot’s filter, consisted of 2 quartz plates in the range of 1879.0–1939.4 nm with less than 1-nm linewidth, was achieved. For the best case (10-ms pump pulse duration, 42-A pump current corresponding to 266 mJ of pump energy), the Q-switched energy was 10.5 mJ with pulse duration of 22 ns corresponding to near 0.5 MW peak power. The 2.5 W of average power with 12.6-kW peak power and 2000-Hz repetition rate was demonstrated for cw pumping regime.     

Photo-induced densification in Er<Superscript>3+</Superscript>/Al doped silica preform plates using 193-nm laser light

The growth rate of Bragg gratings written using 193-nm light from an ArF excimer laser is shown to be non-linear with the pulse energy density for Er³⁺ co-doped Al silica. This yields a refractive-index increase up to a few 10⁻³. We then use phase-shift interferometry to measure the sample surface topography following exposure. Subsequently, we formulate an inhomogeneous stress model to analyse the observed change of volume within the core material. Below pulse energies of 550 mJ/cm², the results show that refractive-index changes are primarily due to a densification process. At higher pulse energies material re-expansion occurs.     

2<Emphasis Type="Italic">µ</Emphasis>m Laser based on an electro-optical <Emphasis Type="Italic">Q</Emphasis>-switched intracavity KTP optical parametric oscillator

An 2 μm pulse laser based on an intracavity optical parameter oscillator (OPO) pumped by an electrooptical Q-switched 1.064 μm laser is realized. A type-II phase-matched (θ = 51.5° and φ = 0) KTP crystal and a limiting diaphragm with a diameter of 4 mm were used. The parameters of the KTP-OPO tuning curves as a function of the phase matching angles were analyzed for the case of 1.064 μm laser pumping. Experiments based on single and double KTPs for walk-off compensation were performed. An output energy of 26 mJ in the 2 μm wavelength region was obtained with a pump-to-signal conversion efficiency of 26%. The center wavelengths of the signal and idle lights were 2165.4 and 2088.6 nm with a FWHM of 3.8 and 4 nm, respectively.     

Nd:GSAG-pulsed laser operation at 943 nm and crystal growth

Laser activity of neodymium-doped gadolinium scandium aluminum garnet (Nd:GSAG) on the transition with an output wavelength around 943 nm was investigated. The emission cross-section was measured with spectroscopic and amplifier approaches demonstrating the applicability of the Nd:GSAG laser for water vapor detection. A Q-switched laser setup delivered 150 ns pulses with 26 mJ output energy and 9% optical to optical efficiency. The laser was diode pumped with up to 50 Hz repetition rate. In the long pulse mode a pulse energy of 83 mJ with 32% optical efficiency was achieved. The output wavelength was controlled by injection seeding. PACS 42.55.Xi; 42.70.Hj     

High peak power Nd:YAG laser pumped by 600-W diode laser stack

The Q-switched laser with triangle slab made of Nd:YAG crystal side pumped by 600-W quasi-cw diode laser stack has been designed. The multimode (M²≈2.6) output energy of about 42 mJ was demonstrated in free running mode for110-mJ pump energy. In Q-switch experiments, the KDDP Pockels cell was placed between the slab and rear mirror in plane-plane cavity with output coupler of 84% transmission. The energy of 8 mJ in 2.1-ns pulse duration was obtained for near TEM₀₀ output beam. For passive Q-switching by means of Cr:YAG crystal of 12.6% unsaturated transmission, the energy of 5.1 mJ in 2.5-ns pulse duration was obtained for output beam close to TEM₀₀ mode.     

High-peak-power,high-repetition-rate LD end-pumped Nd:YVO<Subscript>4</Subscript> burst mode laser

A compact high-peak-power, high-repetition-rate burst mode laser is achieved by an acousto-optical Q-switched Nd:YVO₄ 1064 nm laser directly pumped at 878.6 nm. Pulse trains with 10–100 pulses are obtained using acousto-optical Q-switch at repetition rates of 10–100 kHz under a pulsed pumping with a 1 ms duration. At the maximum pump energy of 108.5 mJ, the pulse energy of 10 kHz burst mode laser reaches 44 mJ corresponding to a single pulse energy of 4.4 mJ and an optical-to-optical efficiency of 40.5 %.The maximum peak power of ~468.1 kW at 10 kHz is obtained with a pulse width of 9.4 ns. The beam quality factor is measured to be M ² ~1.5 and the pulse jitter is estimated to be less than 1 % in both amplitude and time region.     

Broad-band regenerative laser amplification in ytterbium-doped calcium fluoride (Yb:CaF<Subscript>2</Subscript>)

An output pulse energy of 17.3 mJ has been achieved with a diode-pumped Yb:CaF₂ regenerative laser amplifier. The bandwidth of the output pulse spectrum was 7.3 nm, being seeded with femtosecond pulses stretched to 2.2 ns. In cw operation a tuning range of 80 nm has been observed. A maximum pulse energy of 44 mJ at a repetition rate of 1 Hz has been obtained in Q-switched mode. The laser damage threshold of a Yb:CaF₂ crystal has been determined at a wavelength of 1064 nm and a pulse duration of 10 ns. PACS 42.55.Ah; 42.55.Xi; 42.70.Hj     

Vacuum-cored hollow waveguide for transmission of high-energy, nanosecond Nd:YAG laser pulses and its application to biological tissue ablation

A vacuum-cored hollow waveguide has been found to transmit 1064-nm, Q-switched Nd:YAG laser pulses. With this scheme, laser-induced air breakdown was completely suppressed, and the laser-induced damage threshold of the waveguide's inner coating was significantly increased. With a 1-m-long, 1-mm inner-diameter, cyclic olefin polymer-coated silver hollow waveguide, the maximum transmitted laser energy was as great as 158 mJ/pulse (20.1 J/cm(2)), at a repetition rate of 10 Hz in a 90 degrees -bent waveguide condition. The corresponding transmitted peak laser power was 17.6 MW. With the transmitted laser pulses, deep ablation of myocardium tissues was demonstrated in vitro.     

Particle Distributions and Laser-Particle Interactions in an RF Discharge of Silane

We report laser diagnostic studies of capacitively coupled RF discharges containing 0.05-0.45-percent silane in argon. We probed positions between the plane-parallel electrodes by pulsed laser light scattering at several wavelengths. These spatial scans had a resolution of 0.25 mm and they showed unusual particle distributions which varied with silane mole fraction and gas-flow rates. Particle nucleation and growth kinetics were very well demonstrated over this range of discharge parameters. We also studied particle photophysics and demonstrated that ultraviolet pulsed lasers (251.4 and 266 nm) can form silicon atoms from laser-particle interactions. Atoms were formed in both ground and excited states with a concentration that depended linearly on laser energy. However, atoms were not formed by 354- or 532-nm excitation. Particle excitation by 354 nm at energies > 0.5 mJ created a long-time (>0.1 s) perturbation of the discharge chemistry which linearly increased the steady-state (10 Hz) light scattering with increasing 354-nm energy.     

High pulse energy output from tunable solid-state dye laser based on MPMMA doped with PM567

Tunable solid-state dye laser sample based on modified polymethyl methacrylate (MPMMA) with methanol co-doped with pyrromethene 567 (PM567) and Coumarin 440 (C440) was prepared. Tunable dye laser output wavelength from 546 to 594 nm was obtained in an oscillator-amplifier configuration. With the input seed laser energy being about 1.5 mJ, the highest dye laser output energy reached 113.9 mJ, and the corresponding conversion slope efficiency was 51.39%. To the best of our knowledge, the tuning range and narrow linewidth dye output energy is the best under the same condition so far. The linewidth for the seed laser and amplified laser were measured with the result of less than 0.2 nm. With the amplified medium being pumped at a repetition rate of 10 Hz with a pulse energy as high as 120 mJ (the fluence was 0.42 J/cm²), the laser output energy dropped to half of its initial value after approximate 43000 pulses.     

Pumping of titanium sapphire laser

Two methods of Ti:Sapphire pumping for the generation of tunable laser radiation in the visible region were studied. For coherent pumping, the radiation of the second harmonic of a Nd:YAP laser was used and a maximum output energy ofE _out=4.5 mJ was reached from the Ti:Sapphire laser. For noncoherent pumping, two different lengths of flashlamp pulses were used and a maximum ofE _out=300 mJ was obtained. Preliminary estimations of the wavelength range of tunability were made.