High efficiency TEM00 mode, diode-pumped, conduction-cooled, Nd:YAG zig-zag slab laser

We report a compact, conduction-cooled, highly efficient, continuous wave (CW) Nd:YAG slab laser in diode-side-pumped geometry. To achieve high efficiency, a novel laser head for Nd:YAG slab has been developed. For an absorbed pump power of 27.6 W, maximum output power of 10.4 W in multimode and 8.2 W in near-diffraction-limited beam quality has been obtained. Slope and optical-to-optical conversion efficiencies are 45.3% and 37.7% in multimode with beam quality factors (M²) in x and y directions equal to 32 and 8, respectively. TEM₀₀ mode operation was achieved in a hybrid resonator with slope and optical-to-optical conversion efficiencies of 43.2% and 29.7%, respectively. Beam quality factors in x and y directions are ?1.5 and ?1.6 for the whole output power range. The laser radiation was linearly polarized and polarization contrast ratios are >1200:1 in the multimode and 1800:1 in the TEM₀₀ mode operation. In passive Q-switching with Cr⁴⁺:YAG crystal of 68% initial transmission, 18 ns pulsewidth has been achieved with an average power of 2 W at a repetition rate of 16 kHz.     

LD end pumped, actively mode locked and passively Q-switched Nd:YAP laser at 1341 nm

An end pumped Nd:YAP laser at 1341 nm is actively mode locked and passively Q-switched. Pumping was done with a pulsed high power laser diode with maximum power 425 W. V³⁺:YAG with 61% initial transmission served as saturable absorber, and an acousto-optic modulator is used for active mode locking. The output pulse train with 69 ns duration has a total energy of 3.2 mJ with ±4% shot-to-shot fluctuation. The peak output energy of a single mode locked pulse is 0.25 mJ. The pulse duration of a single mode locked pulse is less than 800 ps. The output laser beam is nearly diffraction limited with 1.6 mm diameter, and beam propagation factor M² about 1.3.     

Highly efficient third-harmonic generation with electro-optically Q-switched diode-end-pumped Nd:YVO4 slab laser

We have achieved efficient third-harmonic generation (THG) with an electro-optically Q-switched diode-end-pumped slab laser by cascading second-harmonic and sum-frequency generation in a lithium triborate (LBO) crystal. The high conversion efficiency, short pulse length and high pulse energy is the characteristic of the output 355 nm light. An average power of 11.1 W at a repetition rate of 10 kHz was achieved. The pulse energy is 1.1 mJ and the pulse length is 5 ns. The peak power of pulse is 0.22 MW. The conversion efficiency from 1064 nm to 355 nm reached 44.4% which is to our knowledge the highest conversion efficiency. Furthermore, the 355 nm light is near TEM₀₀ mode. The beam quality is M² < 1.5. In this paper, the experimental setup, results and the factors which can affect the conversion efficiency are discussed.     

885 nm LD end-pumped 22.7 W high beam quality electro-optical Q-switched Nd:YAG laser

We report an 885 nm laser diode (LD) end-pumped high beam quality (M _x ² = 1.322, M _y ² = 1.235) electro-optical Q-switched Nd:YAG laser with TEM₀₀-mode output for the first time. At the absorbed pump power of 59.5 W, a 22.7 W 1064 nm laser was achieved at 10 kHz repetition rate with optical-to-optical efficiency of 38.1%. The maximum pulse energy and shortest pulse width were 5.1 mJ and 14.5 ns at 2 kHz repetition rate, and the calculated peak power was 352 kW.     

LD side-pumped 41 W high beam quality acousto-optical Q-switched single-rod Nd:YAG laser

We report a LD side-pumped high beam quality (M _x ² = 1.20 and M _y ² = 1.19) acousto-optic (AO) Q-switched single-rod Nd:YAG laser with a TEM₀₀-mode dynamic stable cavity. At the pump power of 600 W, 41 W TEM₀₀-mode 1064 nm laser was achieved with electro-optical conversion efficiency of 7%. The repetition rate and pulse width were 30 kHz and 102 ns, respectively with pulse energy of 1.4 mJ and peak power of 13 kW. Up to 24 W of 532 nm green laser was generated by external frequency doubling, corresponding to 59% optical conversion efficiency.     

1444-nm Q-switched pulse generator based on Nd:YAG/V:YAG microchip laser

Q-switched microchip laser emitting radiation at eye-safe wavelength 1444 nm was designed and realized. This laser was based on composite crystal which consists of 4 mm long Nd:YAG active medium diffusion bonded with 1 mm long V:YAG saturable absorber. The diameter of the composite crystal was 5 mm. The initial transmission of the V:YAG part was T ₀ = 94% @ 1440 nm. The microchip resonator consists of dielectric mirrors, directly deposited onto the composite crystal surfaces. These mirrors were specially designed to ensure desired emission at 1444 nm and to prevent parasitic lasing at other Nd³⁺ transmissions. The output coupler with reflectivity 94% for the generated wavelength 1444 nm was placed on the V³⁺-doped part. The laser was operating under pulsed pumping for the duty-cycle up to 50%. With increasing value of mean pumping power a strong decrease of generated pulse length was observed. The shortest generated pulses were 4.2 ns long (FWHM). Stable pulses with energy 34 μJ were generated with repetition rate up to 1.5 kHz. Corresponding pulse peak power was 8.2 kW. The wavelength of linearly polarized TEM₀₀ laser mode was fixed to 1444 nm.     

Diode-end-pumped frequency-doubled Nd:YAP/Cr:YAG laser using a KTP crystal

We present a design for a compact laser-diode-end-pumped Nd:YAP/Cr:YAG q-switched laser in a plano?Cconcave cavity configuration. With an optical-to-optical efficiency of 35%, this laser provides an average output of 1.2 W with 13 mJ at 1080 nm. After that, the laser is frequency doubled by replacing the output coupler with a flat KTP crystal to achieve an output of 8 mJ in 8 ns at 540 nm. At a peak power of 1 MW, the laser emits linearly polarized output with an average power of 800 mW. The calculated M² value is 1.3, the output is very stable, and the laser operates in the TEM₀₀ mode.     

Miniature high-repetition-rate TEA CO2 laser with surface-wire-corona preionization

In this article, an experimental study of a miniature, sealed-off, high-repetition-rate transversely excited atmospheric-pressure (TEA) CO₂ laser with a kind of surface-wire-corona preionization (SWCP) is described. We have utilized an SWCP consisting of SiO₂ dielectric tube and a fine wire strained and attached to the dielectric surface. A BN ceramic material, which has an extremely low coefficient of thermal expansion of about 5 × 10⁻⁷/°C was employed as a supporter of the resonator. A measurement on emission spectra of SWCP has been reported. By applying SWCP to the TEA CO₂ laser, efficient laser operation at an overall efficiency of 9.8% with an output energy of 150 mJ has been achieved from a small discharge volume of 25 cm³ with an active length of 230 mm. At the pulse repetition frequency of 60 Hz, the TEM₀₀ mode of laser beam with pulse width of 60 ns was obtained.     

1 mJ Passively Q-switched Nd:YAB laser using a V:YAG crystal

We describe the design and operation of a diode-pumped compact and efficient Nd:YAB laser operating at 1338 nm. We use a passive Q-switch V:YAG crystal to achieve 1 mJ Q-switched pulses at the laser output. The laser elaborated provides an average power of 1.5 W in the CW regime and 1 W in Qswitched mode with an optical efficiency of 15 and 10%, respectively. A 65 mm plano-concave cavity is formed with an output in the TEM₀₀ mode. At a pulse width of 15 ns, the achieved peak power is 66 kW.     

Optimal ablation of fluorine-doped tin oxide (FTO) thin film layers adopting a simple pulsed Nd:YAG laser with TEM00 mode

In material processing, a laser system with optimal laser parameters has been considered to be significant. Especially, the laser ablation technology is thought to be very important for fabricating a dye-sensitized solar cell (DSSC) module with good quality. Moreover, the TEM₀₀ mode laser beam is the most dominant factor to decide the incident photon to current conversion efficiency (IPCE) characteristics. In order to get the TEM₀₀ mode, a pin-hole is inserted within a simple pulsed Nd:YAG laser resonator. And the spatial field distribution is measured by using three pin-hole diameters of 1.6, 2.0 and 4.0 mm, respectively. At that moment, each case has the same laser beam energy by adjusting the discharge voltage and pulse per second (pps). From those results, it is known that the pin-hole size of 1.6 mm has the perfect TEM₀₀ mode. In addition, at the charging voltage of 1000 V, 10 pps, the feeding speed of 6.08 mm/s and the overlapping rate (OL) of 62%, the scanning electron microscope (SEM) photograph of fluorine-doped tin oxide (FTO) thin film layers shows the best ablation trace.     

Compact passively q-switched Nd:YAG laser for 2D micromachining

We present a compact passively q-switched diode end pumped Nd:YAG laser at 1064 nm for 2D micromachining. It consists of a 5.5 cm long plano-concave end pumped resonator carrying a Cr:YAG passive q-switch inside the cavity. With an optical conversion efficiency of 46 and 33% the laser emits 1.4 W in CW and 986 mW in q-switched mode at a current of 2.5 A. After using a 2 mm circular aperture the output is seen in TEM₀₀ mode with a single pulse energy of 5 mJ. The laser produced circular holes of diameter 75 μm in 25 μm thick Tantalum foils. Actual results of 1D and 2D machining are shown along with the diffraction patters of the samples.     

20-Hz operation of an eye-safe cascade Raman laser with a Ba(NO3)2 crystal

Operation of a 1.598-μm eye-safe third-Stokes Raman laser with a Ba(NO₃)₂ crystal pumped by a 1.064-μm Nd:YAG laser is described. We observed a substantial decrease in the output energy during the first 50 s of the continuous operation at 20 Hz. The energy drop is ∼76% of the initial third-Stokes output. We confirmed negative thermal lensing and thermally induced birefringence in the crystal. With a concave cavity mirror at a matched curvature to the thermal lensing, we obtained an output energy of 11 mJ at 20 Hz. TEM₀₀ output was also obtained with a smaller pump-beam diameter with a highest conversion efficiency of 15.5% for a pumping power of only 45 MW/cm² (0.9 J/cm²). Received: 20 November 2001 / Revised version: 20 February 2002 / Published online: 2 May 2002     

Compact,diode-side-pumped and Q-switched Nd:YLiF<Subscript>4</Subscript> laser cavity operating at 1053 nm with diffraction limited beam quality

This work reports a diode-side-pumped and passively Q-switched Nd:YLiF₄ (YLF) laser operating at 1053 nm using a new laser resonator concept. Very stable pulses of 1 mJ energy with less than 10 ns pulse duration are obtained at 1 kHz repetition rate in a very simple, compact, and robust cavity that uses a double bounce configuration to achieve TEM₀₀ operation.     

LD end-pumped intracavity frequency doubled Yb:YAG laser

A laser diode end-pumped 10 at.% doped Yb:YAG microchip crystal intracavity frequency doubled all solid-stated green laser is reported in this paper. Using one plano-concave resonator, with the pump power of 1.2 W, 44.2 mW TEM₀₀ continuous wave (CW) laser at 525 nm was obtained, the optical conversion efficiency was about 3.7%. When a Cr:YAG crystal with initial transmission of 95.5% inserted in the resonator, the maximum output power of 6.4 mW, pulse duration width of 49.1 ns, pulse repetition rate of 2.45 kHz, and peak power of 53.1 W at 515 nm were achieved when the pump power was 1.2 W. The wavelength changed from 525 nm to 515 nm and the threshold was only 725 mW.     

Passively Q-switched Nd:LuVO4 laser using Cr:YAG as saturable absorber

A passively Q-switched all solid-state Nd:LuVO₄ 1.06 μm laser was demonstrated by using Cr⁴⁺:YAG as saturable absorber. The characteristics of average output power, pulse width, repetition rate, pulse energy, and peak power were studied with different output couplings and initial transmission of saturable absorbers. When output coupling with the transmission of 20% was used, the shortest pulse width of 16 ns at the repetition rate of 12.5 kHz was obtained, which results in the pulse energy of 71 μJ and peak power of 4.43 kW with the initial transmission of 70% of Cr⁴⁺:YAG crystal.     

Single mode oscillation of TEA CO2 laser with an interference resonator

An effective single-longitudinal mode (SLM) pulse TEA CO₂ laser operation was demonstrated using a Michelson’s type resonator with a tilting Fabry-Perot etalon. A modified numerical model of the interference resonator was investigated for designing the laser. The experimentally measured values were found to have good agreement with the numerical model. A pulse width of about 90 ns and the maximum pulse energy of about 300 mJ were achieved at 10.59 μm in SLM and TEM₀₀ mode. The reliability of producing SLM pulses was 100% and there was no damage on the etalon. By turning the interference resonator, the SLM output was tuned 44 lines of the CO₂ spectrum.     

Efficient multiple-longitudinally diode laser pumped Nd:YAG slab laser

The operation of an eightfold longitudinally diode laser pumped 1.06m cw Nd:YAG slab laser is demonstrated. The 809 nm diode radiation is focused through a dichroic coating into each laser channel starting from the reflection points of the 1.06m beam in the slab crystal. At an absorbed pump power in the crystal of 2830 mW a maximum cw TEM₀₀ output of 1075 mW was achieved with a corresponding slope efficiency of 42.5%.     

High-power neodymium-doped mixed vanadate bounce geometry laser, mode locked with nonlinear mirror

The highest power neodymium-doped mixed vanadate laser oscillator is presented. Using a crystal of Nd:Gd_0.6Y_0.4VO₄ in the bounce geometry, average output powers of 27.5?W in multimode and 23?W in TEM₀₀ operation were achieved. The first nonlinear mirror mode-locked operation of a mixed vanadate laser is also presented, with 16.8?W output power??the highest power mode-locked mixed vanadate oscillator, to the best of our knowledge. Self-starting continuous-wave mode locking was observed at a repetition rate of 100?MHz, pulse duration of 12.7?ps and central wavelength of 1063.8?nm, in TEM₀₀ mode.     

500.5-nm blue-green laser based on sum-frequency mixing of diode pumped neodymium lasers

We report for the first time a continuous-wave (CW) coherent radiation at 500.5 nm by intracavity sum-frequency generation of 1063 nm Nd:GdVO₄ laser and 946 nm Nd:YAG laser. Blue-green laser is obtained by using a doubly cavity, type-II critical phase matching KTiOPO₄ (KTP) crystal sum-frequency mixing. With total pump power of 27.8 W, TEM₀₀ mode blue-green laser at 500.5 nm of 421 mW is obtained. At the output power level of 421 mW, the blue-green power stability is better than 2.8% and laser beam quality M ² factor is 1.37.     

Yellow light generation by frequency doubling of a diode-pumped Nd:YAG laser

We demonstrate the generation of TEM₀₀ mode yellow light in critically type II phase-matched KTiOPO₄ (KTP) with intracavity frequency doubling of a diode-pumped Nd:YAG laser at room temperature. After a 150 μm thick etalon have been inserted into the cavity, the stability and beam quality of the second harmonic generation (SHG) is enhanced. A continuous wave (CW) TEM₀₀ mode output power of 1.67 W at 556 nm is obtained at a pump level of 16 W. The total optical to optical conversion efficiency is about 10.44%. To the best of our knowledge, this is the first Watt-level yellow light generation by frequency doubling of Nd:YAG laser.