Quenching of triplet vinylidene radicals by helium

Triplet vinylidene radicals, produced in the vacuum-ultraviolet photolysis of acetylene, are observed in absorption at 137.4 nm. The lifetime in the presence of helium, for both the protonated and deuterated species, has been determined. Expressed as a bimolecular rate constant the values are k_He^H = (1.3 ± 0.3) × 10^?14 cm³ molecule^?1 s^?1 and k_He^D = (2.4 ± 0.4 × 10^?15 cm³ molecule^?1 s^?1. An upper limit for removal by acetylene has been deduced.     

Optimization of a sensitive method for the “switch-on” determination of mercury(II) in waters using Rhodamine B capped gold nanoparticles as a fluorescence sensor

Monodisperse and “naked” gold nanoparticles (GNPs) were modified with thioglycolic acid (TGA). The fluorescence of rhodamine B (RB) is quenched completely by the gold NPs surface with negative charge mainly as a result of fluorescence resonance energy transition (FRET) and collision. The quenching mechanism can be described by a Langmuir isotherm, which was systematically investigated by steady-state fluorescence spectrometry and absorption spectrometry. Hg(II) ion disrupts the GNPs–RB pair, producing a large “switch-on” fluorescence. A low background, highly sensitive and reproducible fluorescence assay for Hg(II) is presented. Under the optimum conditions, the restoration fluorescence intensity is proportional to the concentration of Hg(II). The calibration graphs are linear over the range of 1.0?×?10^?9 to 3.1?×?10^?8 mol L^?1 with a detection limit of 4.0?×?10^?10 mol L^?1. The relative standard deviation was 1.2% for a 5.0?×?10^?9 mol L^?1 Hg(II) solution (N?=?6). This method was applied to the analysis of Hg(II) in environmental water samples, and the results were consistent with those of atomic absorption spectroscopy (AAS).     

Determination of trace elements in gallium arsenide by graphite-furnace atomic absorption spectrometry after pretreatment in gas streams

Atomic absorption spectrometry (AAS) with a resistively-heated graphite furnace is used for the determination of chromium (0.3–1 atom/10⁶ atom) in chromium-doped gallium arsenide after pretreatment in a separate furnace in a stream of argon to remove arsenic, and of manganese and silver (0.03 and 0.04 atom/10⁶ atoms, respectively) by a similar procedure after pretreatment with argon and chlorine, the latter to remove both gallium and arsenic as volatile chlorides. Results for chromium were in agreement with those obtained by furnace AAS after dissolution and by spark-source mass spectrometry (SSMS) but AAS after dissolution is more precise. Results for manganese and silver obtained by both gas pretreatments were in good agreement, but were higher than those obtained for presparked material by SSMS, indicating that surface contamination of gallium arsenide was not completely removed by the etching methods used. The procedures established that the concentrations of bismuth, indium and lead in the gallium arsenide sample were below the limits of detection of 3 × 10^?3, 10 × 10^?3 and 1 × 10^?3 atom/10⁶ atoms, respectively. In all cases, calibration graphs were constructed from data obtained with aqueous solutions of appropriate salts.     

Indirect A.C. Oscillopolarographic Determination of Total Monomeric and Acid-Reactive Aluminum in Natural Waters by Using Pyrocatechol Violet

ABSTRACT

Indirect determination of total monomelic and acid-reactive aluminum in natural waters by a.c. oscillopolarography in the presence of pyrocatechol violet (PCV) is presented in this paper. In 0.5 mol 1^?1 NH₄Ac buffer solution (pH 6.4) containing l×lO^?3 mol 1^?1 PCV, PCV yields two incisions on the a.c oscillogram at the potentials of - 0.80 and - 1.20 V, respectively. The incision depth declines when adding aluminum in the solution. The decreases of incision depth (Ep = -1.20 V) has a linear relationship with increasing Al concentrations (4×10^?7 - 4×10^?6 mol 1^?). It is the basis for indirect quantitative analysis. The relative standard deviation is 8.3% for 1×10^?6 mol 1^?1 Al (n = 10) and the detection limit is 2 × 10^?7 mol 1^?1. The proposed method has been applied to determine total and acid-reactive Al in natural waters and the results are compared with Driscoll's 8-HQ-MIBK-GF/AAS and PCV colorimetric methods.     

Modified carbon paste electrode for potentiometric determination of aluminium ion in spiked real water sample

The present paper describes the development of a new chemically modified carbon paste electrode based on azithromycin (AMC) that considered as a selective aluminium recognition agent in the carbon paste electrode (CPE). This electrode was fully characterized in terms of composition, response time, usable pH range and temperature. The electrode exhibited a Nernstian response for Al³⁺ ion over a concentration range from 7.0 × 10^–6 to 1.0 × 10^–2 mol L^–1 with a slope of 21.3 ± 0.18 mV decade^–1 and the limit of detection was 6.0 × 10^–6 mol L^?1. It had a response time of about 6 s. The proposed sensor possesses a very good selectivity with respect to a variety of other cations. Finally this modified electrode was applied for the determination of the concentration of Al³⁺ ion in different water samples and the obtained results were comparable with those obtained with atomic absorption spectrometer (AAS).     

Quantitative goldbestimmung in filmmaterialien mittels flammenloser atomabsorption

A graphite rod electrothermal atomizer has been used for the AAS determination of traces of gold in hydrochloric and in hydrobromic acid solutions, and also after extraction into HBr-saturated methyl isobutyl ketone. Photographic film samples were decomposed first by enzyme action then by nitric acid/peroxide oxidation, and the gold was extracted into MIBK. For 10-μl aliquots of solution the 3s limits of detection were 3 × 10^?10g for aqueous solutions, 7 × 10^?10g for MIBK, and 7 × 10^?9 g/cm² for film.     

Synthesis of New Reagent 2,6‐Diacetylpyridine Bis‐4‐Phenyl‐3‐Thiosemicarbazone (2,6‐DAPBPTSC): Selective,Sensitive and Extractive Spectrophotometric Determination of Co(II) in Vegetable,Soil, Pharmaceutical and Alloy Samples

New synthesized reagent 2,6‐diacetylpyridine bis‐4‐phenyl‐3‐thiosemicarbazone (2,6‐DAPBPTSC) is proposed as a sensitive and selective analytical reagent for the extractive spectrophotometric determination of cobalt(II). Cobalt(II) forms a reddish brown colored complex with 2,6‐DAPBPTSC, which is extracted into isoamylalcohol, under optimum conditions. The maximum absorption of the isoamylalcohol extract is measured at 400 nm. Beer's law is applied in the range 0.6‐6.0 ppm of cobalt(II). The molar absorptivity and Sandell's sensitivity of the complex is calculated as 2.2 × 10⁴ L mol^?1 cm^?1 and 2.68 × 10^?3 μg cm^?2, respectively. An adequate linearity with a correlation coefficient value of 0.969 is obtained for the Co(II)‐2,6‐DAPBPTSC complex. The instability constant of the complex, calculated from Asmus' method is 3.75 × 10^?4 The precision and accuracy of the method is checked with calculation of relative standard deviation (n = 5), 0.388 and the detection limit a value is 0.0028 μg mL^?1. The method is successfully employed for the determination of cobalt(II) in real samples, such as vegetables, soil, water samples, standard alloy samples, and the performance of the present method was evaluated in terms of Student ‘t’ test and Variance ‘f’ test, which indicates the significance of the present method is an inter comparison of the experimental values, using atomic absorption spectrometer (AAS).     

Dimensional and Optoelectronic Tuning of Lead-free Perovskite Cs3Bi2I9−nBrn Single Crystals for Enhanced Hard X-ray Detection

Inorganic Bi-based perovskites have shown great potential in X-ray detection for their large absorption to X-rays, diverse low-dimensional structures, and eco-friendliness without toxic metals. However, they suffer from poor carrier transport properties compared to Pb-based perovskites. Here, we propose a mixed-halogen strategy to tune the structural dimensions and optoelectronic properties of Cs₃Bi₂I_9−nBr_n (0≤n≤9). Ten centimeter-sized single crystals are successfully grown by the Bridgman technique. Upon doping bromine to zero-dimensional Cs₃Bi₂I₉, the crystal transforms into a two-dimensional structure as the bromine content reaches Cs₃Bi₂I₈Br. Correspondingly, the optoelectronic properties are adjusted. Among these crystals, Cs₃Bi₂I₈Br exhibits negligible ion migration, moderate resistivity, and the best carrier transport capability. The sensitivities in 100 keV hard X-ray detection are 1.33×10⁴ and 1.74×10⁴ μC Gy_air⁻¹ cm⁻² at room temperature and 75 °C, respectively, which are the highest among all reported bismuth perovskites. Moreover, the lowest detection limit of 28.6 nGy_air s⁻¹ and ultralow dark current drift of 9.12×10⁻⁹ nA cm⁻¹ s⁻¹ V⁻¹ are obtained owing to the high ionic activation energy. Our work demonstrates that Br incorporation is an effective strategy to enhance the X-ray detection performance by tuning the dimensional and optoelectronic properties.     

Nickel determination in osteoblast-like cell culture medium by adsorptive cathodic stripping voltammetry with a mercury microelectrode

The purpose of this study is to investigate the influence of nickel, which is an alloying element in commonly used metallic biomaterials, on the biomaterials mineralization process. An electrochemical method was developed to quantify this metal ion in osteoblast-like cell culture medium (OST) by performing adsorptive cathodic stripping voltammetry (CSV) with dimethylglyoxime (DMG) at a mercury film microelectrode (MFM). The optimized analytical conditions and the square-wave CSV parameters for the analysis are: DMG concentration: 5.00 × 10⁻⁴ mol L⁻¹; ammonium chloride buffer: 0.10 mol L⁻¹ (pH 9.2); frequency: 50 Hz, amplitude 20 mV; step: 2 mV; adsorption time: 10 s, deposition potential: −0.70 V and reduction potential: −1.20 V. The limit of detection was 7.70 × 10⁻⁹ mol L⁻¹ for an adsorption time of 10 s. The results achieved by CSV using the MFM were compared to those obtained by atomic absorption spectrometry (AAS) to ensure the reliability of the electrochemical method. The mineralization process was evaluated by biochemical and histochemical assays.     

The high-performance liquid chromatography and detection of phospholipids and triglycerides: Part 2. Comparison of an ultraviolet absorption and post-column reactor detector

A liquid chromatographic ultraviolet absorption detector (at 195 nm) and a novel postcolumn reactor detector are compared for use in the detection of triglyceride and phospholipid molecular species. The detection limit for the u.v. detector depends on the degree of unsaturation of the lipid sample (3 × 10^-6–2 × 10^-8 M in the detector cell for 0–3 double bonds per acyl group). The post-column reactor detector is responsive to equivalents of lipid and has detection limits of 5 × 10^-7 M for triglycerides and 2 × 10^-6 M for phospholipids. The log u.v./post-column reactor detector response ratios are linearly related to the log of the degree of unsaturation of the lipid, indicating the usefulness of both detectors for quantifying triglycerides and phospholipids.     

Electrothermal atomic absorption spectrometry of elements after electrochemical deposition on graphite electrodes

The application of electrochemical deposition on graphite rods for separation and preconcentration prior to electrothermal atomic absorption spectrometry (a.a.s.) is examined. The metals to be determined are electrolyzed onto a graphite rod which is tehn transferred to a cup atomizer for a.a.s. Although only some of the element present in the solution is deposited on the surface of the graphite rod, favorable preconcentration rates are obtained. The method was tested on the determination of cadmium in aqueous solution. The precision is satisfactory for concentrations down to 5 × 10^?8 g l^?1 cadmium, and the detection limit is 4 × 10^?9 g l^?1.     

A Highly Sensitive Electrochemiluminescence Choline Biosensor Based on Poly(aniline‐luminol‐hemin) Nanocomposites

Poly(aniline‐luminol‐hemin) nanocomposites are prepared on an electrode surface through electropolymerization, and a highly sensitive electrochemiluminescence (ECL) biosensor for choline is developed based on the poly(aniline‐luminol‐hemin) nanocomposites and an enzyme catalyzed reaction of choline oxidase (CHOD). The obtained nanocomposites are characterized by scanning electron microscopy (SEM), atomic absorption spectrometry (AAS) and ECL. The results indicate that hemin can be incorporated into the poly(aniline‐luminol) nanocomposites using the facile electropolymerization method, and the poly(aniline‐luminol‐hemin) nanocomposites are rod shaped porous nanostructure. Moreover, the poly(aniline‐luminol‐hemin) nanocomposites exhibit higher ECL intensity than poly(aniline‐luminol) nanocomposites in alkaline media due to the catalytic effect of hemin on the ECL of the polymerized luminol and the electron transfer ability of hemin in the nanocomposites. CHOD is immobilized on the surface of the poly(aniline‐luminol‐hemin) nanocomposites modified electrode with glutaraldehyde, and the ECL biosensor based on poly(aniline‐luminol‐hemin)/CHOD exhibits a wider linear range for the choline detection. The enhanced ECL signals are linear with the logarithm of concentration of choline over the range of 1.0×10^?11～1.0×10^?7 mol L^?1 with a low detection limit of 1.2×10^?12 mol L^?1. Moreover, the proposed biosensor is successfully applied to the detection of choline in milk.     

Modified Screen-Printed Electrode for Potentiometric Determination of Copper(II) in Water Samples

Modified screen printed (SPE) and carbon paste electrodes (CPE) with phenanthroline–tetraphenyl borate ionophore [Phen:TPB] were fabricated for the determination of copper(II). The modified electrodes have linear responses over a wide concentration range (1 × 10^?6–1 × 10^?2 mol·L^?1) of copper(II) ion at 25 °C with divalent cationic slopes of 29.85 ± 0.58 and 29.45 ± 0.81 mV·decade^?1 and exhibit a detection limit of 1 × 10^?6 mol·L^?1 for SPE and CPE. The selectivity coefficient was measured using the match potential method in acetate buffer of pH = 4.2. The modified SPE and CPE sensors show high selectivity and sensitivity for determination of copper(II) and also show stable and reproducible response over a period of five and three months for SPE and CPE sensors, respectively. This method can be used for determination of copper(II) in water, soil, plant and fish tissue samples and the results obtained agreed with those obtained with atomic absorption spectrometer (AAS).     

Evaluation of new high-frequency discharge lamps for atomic absorption and atomic fluorescence spectrometry of cadmium,lead and zinc

High-frequency discharge lamps with a hollow electrode are successfully utilized as the spectral line sources for atomic absorption and atomic fluorescence spectrometry of cadmium, lead and zinc. The sensitivities for atomic absorption spectrometry are superior to those obtained with commercially available hollow-cathode lamps by factors of 1.5 (Cd), 1.4 (Pb) and l.6 (Zn). Detection limits for non-dispersive atomic fluorescence spectrometry with graphite furnace atomization are 1 × 10^-13 g (Cd), 3 × 10^-11 g (Pb) and 2 × 10^-13 g (Zn). The linear analytical range covers over four (Cd, Zn) and three (Pb) decades of concentration above the detection limits.     

Flow Injection Chemiluminescence Determination of Phenol in Neutral Medium

A new flow injection chemiluminescence method for the determination of phenol was proposed, based upon the chemiluminescence reaction of phenol, N-bromosuccinimide, and hydrogen peroxide in neutral aqueous medium in the presence of cetyltrimethylammonium bromide surfactant micelles. The chemiluminescence signal was proportional to the concentration of phenol in the range of 1.0 × 10^?7?8.0 × 10^?6 g/mL with a detection limit of 3 × 10^?8 g/mL. The relative standard deviation for 1.0 × 10^?6 g/mL phenol solution was 2.0% (n = 11). The proposed method was successfully applied to the determination of phenol in phenol ear drops. A possible CL reaction mechanism was also discussed briefly.     

Octaethylporphyrin as an ionophore for aluminum potentiometric sensor based on carbon paste electrode

A new sensor to quantitatively sense aluminum in real sample conditions is presented that uses the potentiometric ion selective electrodes. Aluminum is a cation that plays an important role in the environmental process. This approach is proposed to determine aluminum levels in real samples in the required range (10^?6–10^?2 M). Carbon paste electrode (CPE) is introduced here as a potentiometric sensor to measure free concentration of aluminum ion. Octaethylporphyrin (OEP) acts as a selective aluminum recognition agent in the CPE. The suitable selectivity coefficient is obtained for the CPEs compare to interfering cation. The Nernstian slope and detection limit are achieved 18.4 mV/decade and 2.5 × 10^?6 M Al³⁺, respectively. Finally, the proposed method is applied to determine aluminum concentration in real water samples and the result of this method is in agreement with the result of atomic absorption spectroscopy (AAS).     

Lead(II) Potentiometric Sensor Based on 1,4,8,11‐Tetrathiacyclotetradecane Neutral Carrier and Lipophilic Additives

A potentiometric sensor for lead(II) ions based on the use of 1,4,8,11‐tetrathiacyclotetradecane (TTCTD) as a neutral ionophore and potassium tetrakis‐(p‐chlorophenyl)borate as a lipophilic additive in plasticized PVC membranes is developed. The sensor exhibits linear potentiometric response towards lead(II) ions over the concentration range of 1.0×10^?5–1.0×10^?2 mol L^?1 with a Nernstian slope of 29.9 mV decade^?1 and a lower limit of detection of 2.2×10^?6 mol L^?1 Pb(II) ions over the pH range of 3–6.5. Sensor membrane without a lipophilic additive displays poor response. The sensor shows high selectivity for Pb(II) over a wide variety of alkali, alkaline earth and transition metal ions. The sensor shows long life span, high reproducibility, fast response and long term stability. Validation of the method by measuring the lower limit of detection, lower limit of linear range, accuracy, precision and sensitivity reveals good performance characteristics of the proposed sensor. The developed sensor is successfully applied to direct determination of lead(II) in real samples. The sensor is also used as an indicator electrode for the potentiometric titration of Pb(II) with EDTA and potassium chromate. The results obtained agree fairly well with data obtained by AAS.     

Electrochemical Detection of Epinephrine Using an L-Glutamic Acid Functionalized Graphene Modified Electrode

The development and application of an L-glutamic acid functionalized graphene nanocomposite, modified glassy carbon electrode are reported for the determination of epinephrine. The properties of the nanocomposite were characterized by scanning electron microscopy, ultraviolet-visible absorption spectroscopy, infrared spectroscopy, cyclic voltammetry, and electrochemical impedance spectroscopy. The modified electrode had high sensitivity and strongly catalytic activity for the detection of epinephrine. A linear relationship between the epinephrine concentration and the current response was obtained in the range of 1 × 10^?7 M to 1 × 10^?3 M by differential pulse voltammetry with a limit of detection of 3 × 10^?8 M. The modified electrode was employed to determine epinephrine in urine with satisfactory results.     

Sensitive detection of dopamine using micelle-enhanced and terbium-sensitized fluorescence

A new terbium sensitized spectrofluorimetric method was developed for the determination of trace amounts of dopamine (DA) using ethylenediaminetetraacetic acid as co-ligand and cetyltrimethylammonium chloride as sensitizer. UV absorption and fluorescent spectra were used to investigate the photophysical properties of the ternary complex. Under the optimum conditions, the enhanced fluorescence intensities of the Tb(III) complexes increased linearly with the concentration of DA over the ranges 8 × 10^–8–5 × 10^–5 M and the limit of detection for DA was found to be 2.4 × 10^–8 M. The proposed method has been applied for the quantitative determination of DA in a pharmaceutical preparation and urine samples. The possible energy transfer mechanisms in the lanthanide complexes were discussed.     

Einsatz der echten Integration in der Atomabsorptions-Spektroskopie

An improvement of the signal-to-noise ratio in atomic absorption spectroscopy may be obtained by each of the following three methods of signal averaging:

increase of the time constant

digital signal averaging

true integration of the signal

The most adequate of these methods appears to be true integration. Two examples are presented to demonstrate the improved signal-to-noise ratio due to the application of this method:

trace analysis of mercury in water by means of flameless AAS. The detection limit appears to be 0.2 ng which corresponds to a concentration of 2 · 10^?13 g/ml.

trace analysis of copper in human urine by means of flame AAS: 1,3 · 10^?8 g/ml copper could be detected without any solvent extraction process.