Boron analysis in biological material: microwave digestion procedure and determination by different methods

Investigations were made on the determination of boron in biological material. A procedure using the microwave digestion technique was optimised. The analyses were performed by photometry with azomethine-H, fluorimetry with carminic acid, inductively coupled plasma atomic emission spectrometry and inductively coupled plasma mass spectrometry. The matrix interferences, the interferences caused by iron and the detection limits were investigated for these methods. Determinations were performed for plant material, wheat, milk, meat and blood plasma. Recoveries and precision of all methods were studied. To test accuracy and precision, four NBS reference materials were analysed and the results compared with the values in literature. Good recoveries were found with all methods, except the fluorimetric technique. The boron content found in the NBS standard reference materials agreed well with data reported before. Best precision was obtained for the two ICP methods. The azomethine-H method gave good results when material of high boron content was analysed. With the carminic acid method no reliable results were achieved.     

电感耦合等离子体-发射光谱分析中硫酸基体效应及抑制

研究了电感耦合等离子体-发射光谱分析中的硫酸基体效应及克服干扰的有效方法。对2%~20%范围内4种不同体积分数H2SO4溶液中30种元素的基体效应进行了观察,发现H2SO4对各元素的谱线发射强度均存在明显的抑制作用。实验证实体积分数5%乙酸可有效抑制H2SO4的基体效应,并建立了H2SO4溶液中痕量元素的电感耦合等离子体-发射光谱分析法。     

Selective preconcentration of Lanthanum(III) by Coriolus versicolor immobilised on Amberlite XAD-4 and its determination by ICP-OES

Coriolus versicolor, a wood fungus, was immobilised on Amberlite XAD-4 and used as solid-phase biosorbent for preconcentrations of rare earth elements. La(III), Th(IV), U(IV) and Ce(III) were subjected to solid-phase extraction procedure. We observed that La(III) was selectively preconcentrated, while other ions remained in solution at pH 6.0. 5.0 mL of 1.0 mol L^?1 HCl was used to elaute La(III) from column. 250 mg of C. versicolor loaded on 1000 mg of XAD-4 was optimised as solid-phase matrix. Concentrations of ions in solutions were determined by inductively coupled plasma– optical emission spectrometry (ICP-OES). The calibration plot after preconcentration was linear in the range from 1.0 to 50.0 ng mL^?1 for La(III). Limit of detection was found as 0.27 ng mL^?1 for La(III) by SPE method. Relative standard deviation was found lower than 6.7% for 1.0 ng mL^?1 of La(III) solution (n = 10). The sensitivity of ICP-OES was improved by a factor of 46.8. The applicability of the method was validated through the analysis of certified reference samples of tea (NCS ZC-73014) and spinach (NCS ZC-73013).     

Automated method for the determination of boron in water by flow-injection analysis with in-line preconcentration and spectrophotometric detection

A sensitive, automated method for the determination of boron in water samples is described, involving flow injection with on-line ion-exchange preconcentration and spectrophotometric detection of the azomethine-H—boron complex. The method is applicable to various water samples and is free from interferences, even in coloured samples. Detection limits of 5 μg l^?1 at 20 samples h^?1 and 1 μg l^?1 at 10 samples h^?1 with relative standard deviations of < 10% at 1–10 μg l^?1 and < 5%at 10–200 μg l^?1 levels of boron were achieved. The recoveries for spiked natural water samples ranged from 96 to 101%. The method compares favourably with inductively coupled plasma atomic emission spectrometry.     

悬浮液进样电感藕合等离子体发射光谱中颗粒的输运和蒸发行为

以碳化硼为例,研究了悬浮液雾化进样中的粒子在传输和蒸发过程中的行为,并对分析结果出现负偏离的原因进行了详细探讨.对比悬浮液颗粒的原始粒径分布和经过传输过程后的粒径分布,获得到达等离子体的颗粒粒径上限小于10 Am.样品中存在的部分超大粒径的颗粒(d>>10 μm)会严重影响可传输区域颗粒(d<10 μm)的质量运输效率...     

On-line extraction and determination of uranium in aqueous samples using multi-walled carbon nanotubes-coated cellulose acetate membrane

In this work, multi-walled carbon nanotubes (MWCNTs)-coated cellulose acetate membrane was used for on-line extraction and pre-concentration of uranium from aqueous samples prior to inductively coupled plasma optical emission spectrometry (ICP-OES) determination. Sample solutions containing the U(VI)-2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (Br-PADAP) complex were passed through the membrane. The adsorbed analyte was subsequently eluted from the membrane with acid, which was directly introduced into the ICP-OES nebuliser. The main variables affecting the pre-concentration and determination steps of uranium were studied and optimised. Under the optimised conditions, the enrichment factor of 150 and the detection limit of 0.16 μg L^–1 were obtained. This method was successfully used for determination of uranium in environmental water samples.     

A selective modified nanoporous silica as sorbent for separation and preconcentration of dysprosium in water samples prior to ICP-OES determination

In this research a new physically functionalized nanoporous silica (SBA-15) using N′-[(2-hydroxy phenyl) methylene] benzohydrazide (BBH) was utilized as a selective sorbent for the separation, preconcentration and determination of dysprosium (Dy) in natural water by inductively coupled plasma optical emission spectrometry (ICP-OES). The selectivity of BBH to Dy (III) ion was previously tested by conductometric and spectroscopic methods. Conditions for effective adsorption of Dy were optimized with respect to experimental parameters in batch process. The extraction recovery was 96.5, analytical curve was linear in the range 0.2–1000?µgL^?1, and the detection limit was 0.05?ng?mL^?1. The relative standard deviation (RSD) under optimal conditions was 3.2% (n?=?10). The sorbent exhibited high adsorption capacity and fast rate of equilibrium for sorption of Dy ions. The method was applied for recovery and determination of dysprosium in different environmental water samples.     

Determination of trace elements in lithium niobate crystals by solid sampling and solution-based spectrometry methods

Solid sampling (SS) graphite furnace atomic absorption spectrometry (GFAAS) and solution-based (SB) methods of GFAAS, flame atomic absorption spectrometry (FAAS), inductively coupled plasma optical emission spectrometry (ICP-OES) and inductively coupled plasma mass spectrometry (ICP-MS) were elaborated and/or optimized for the determination of Cr, Fe and Mn trace elements used as dopants in lithium niobate optical crystals.     

A matrix effect and accuracy evaluation for the determination of elements in milk powder LIBS and laser ablation/ICP-OES spectrometry

Laser ablation coupled to inductively coupled plasma optical emission spectrometry (LA-ICP-OES) and laser-induced breakdown spectroscopy (LIBS) were investigated for the determination of Ca, Mg, Zn and Na in milk samples. The accuracy of both methods was evaluated by comparison of the concentration found using LA-ICP-OES and LIBS with classical wet digestion associated with ICP-OES determination. The results were not fully acceptable, with biases from less than 1% to more than 60%. Matrix effects were also investigated. The sample matrix can influence the temperature, electron number density (n _e) and other excitation characteristics in the ICP. These ICP characteristics were studied and evaluated during ablation of eight milk samples. Differences in n _e (from 8.9 to 13.8 × 10¹⁴ cm⁻³) and rotational temperature (ranging from 3,400 to 4,400 K) occurred with no correlation with trueness. LIBS results obtained after classical external calibration procedure gave degraded accuracy, indicating a strong matrix effect. The LIBS measurements clearly showed that the major problem in LA-ICP was related to the ablation process and that LIBS spectroscopy is an excellent diagnostic tool for LA-ICP techniques.     

Determination of acid volatile sulphur in river sediments by ICP-OES coupled with purge and trap method

The developed and tested method is based on the acid volatile sulphur (AVS) releasing from a sample of sediment by acidification with hydrochloric acid and sequential absorption of released hydrogen sulphide into the absorption solution of sodium hydroxide. Total sulphur absorbed in the absorption solution is subsequently determined by inductively coupled plasma optical emission spectrometry (ICP-OES) technique. The method was tested using both model and real samples of the river sediment. Obtained results were compared with the results of iodometric determination as the method routinely used for the AVS determination. In case of using ICP-OES with purge and trap, there is no spectral interference of calcium; therefore for the determination of sulphur, it is possible to use atomic emission line of sulphur S I 180.7 nm. The tested method provides the results comparable with the iodometric method within the range of tested concentrations. The detection limit (LOD) of this method is 0.09 mg· S^2? ? L^?1 in the absorption solution which corresponds to 0.23 mg S^2?·kg^?1 in a sediment. Value of LOD is comparable with the iodometric determination.     

Determination of trace amounts of sodium and lithium in zirconium dioxide (ZrO2) using liquid electrode plasma optical emission spectrometry

This paper describes a quantitative measurement of trace elements (Na, Li) in high purity zirconium dioxide powder using liquid electrode plasma optical emission spectrometry (LEP-OES). Conventionally, for such type of measurements, inductively coupled plasma optical emission spectrometry (ICP-OES) is frequently employed. The detection limits of elements in zirconium by ICP-OES are degraded due to the spectra interference between the trace elements and zirconium of the matrix, because zirconium is a line rich element in spectra obtained by ICP-OES. LEP-OES is an elemental analysis method developed by the authors. The measurement principle is simple, as follows. Sample solution is put into a narrow channel on a small cuvette and voltage pulse is applied from both ends of the channel. At the center of the channel which is made narrower, the voltage and current are concentrated there, and plasma is generated. From the emission of the plasma, the quantitative analysis of the elements in the solution is achieved. The LEP-OES has the property that the emission of zirconium is relatively weak, so that highly sensitive measurement of trace elements in zirconium matrix can be conducted without interference. Sample solution is prepared by dissolving high purity zirconium dioxide powder and trace amounts of Na or Li with sulfuric acid. The voltage dependence and the pulse width dependence of optical emission spectra are also investigated. With increase of the voltage or the pulse width, the ratio of emission intensities of Na to those of hydrogen increases. This suggests that the ratio of sensitivity of two elements is variable, that means the element selectivity is controllable to some extent by the measurement conditions in LEP-OES. In the case of Na and H, the ratio can be controlled from 7.4 to 21.6%. Finally, the detection limits (3S.D.) of the trace elements, Na and Li, in 4000 μg g⁻¹ zirconium dioxide aqueous solution are found to be 0.02 and 0.133 μg g⁻¹, respectively. These values correspond to 5 μg g⁻¹ for Na, 33.25 μg g⁻¹ for Li in original high purity zirconium dioxide powder. The correlation coefficient of calibration curve was 0.995 for Na, 0.985 for Li. Those are comparable to the literature values of detection limits using ICP-OES.     

Synthesis and Efficiency of Poly(Acryl- p-Nitrophenylamidrazone- p-Nitrophenylhydrazide) Chelating Fibre for Pre-Concentration and Separation of Trace Concentrations of Bi 3+, In 3+, Sn 4+, Ga 3+ and Ti 4+

A new poly(acryl-p-nitrophenylamidrazone-p-nitrophenylhydrazide) chelating fibre was synthesized from polyacrylnitrile fibre, and the structure of the chelating fibre was determined with the help of the FT-IR spectrum. The parameters influencing the efficiency of the fibre for concentrating trace amounts of Bi³⁺, In³⁺, Sn⁴⁺, Ga³⁺ and Ti⁴⁺, including sample acidity during enrichment, flow rate, adsorptive capacity, re-usability, interfering ions and desorption conditions were investigated. Trace Bi³⁺, In³⁺, Sn⁴⁺, Ga³⁺ and Ti⁴⁺ were enriched and separated from real sample solutions and detected using inductively coupled plasma optical emission spectrometry (ICP-OES) with satisfactory results. The experiments show that the method is rapid, precise, simple and convenient to use.     

Micro-homogeneity studies of boron carbide powders

We have studied the micro-homogeneity of boron carbide powders by inductively coupled plasma optical emission spectrometry (ICP-OES) and total reflection X-ray fluorescence spectrometry (TXRF) using slurry sampling. To get information on the particle size distributions of the powders, the stabilized slurries of boron carbide powders were nebulized, the aerosols were transported into a Batelle impactor and the droplets were collected on the impactor stages bearing TXRF sample holders. In a first series of measurements, parameters of the impaction like the duration of the impaction and the use of glutinous substance on the sample holders were optimized. The different mass size fractions for industrial boron carbide powders were determined by weight measurements of the fractions collected on the different stages. The established particle size distributions were in the range of 0.5 to >16 μm and found similar to those determined by laser diffraction reported elsewhere. Analyses of the mass fractions by slurry sampling TXRF showed that Ca, Ti, Cr, Mn, Fe, Ni and Cu within the measurements errors were homogeneously distributed over the mass fractions between 0.5 and 4 μm and that their concentrations agreed with the bulk composition, as determined with ICP-OES subsequent to digestion. However, light underestimates were found at the 5 (Mn) up to 150 μg g^?1 (Fe) level. Finally, boron carbide powders were washed out with nitric acid with different concentrations and leaching solutions and the residues were analyzed by ICP-OES and TXRF respectively. It is shown that up to 60% of the residual trace impurities in the powder studied can be removed by leaching with 34% (v/v) of nitric acid.

Simultaneous determination of Cd,Cr, Cu,Ni, Pb and Zn in sewage sludge by slurry introduction ICP-OES method

In order to evaluate the slurry nebulisation method as an alternative method for analysis of sewage sludge, the metal content of sludge samples of different origins was determined. The concentrations of six elements: Cd, Cr, Cu, Ni, Pb, and Zn were determined by introducing the sludge as a slurry into an inductively coupled plasma optical emission spectrometer (ICP-OES). Calibration was performed by using aqueous standard solutions. For comparison, the sewage sludge was also digested by microwave digestion and introduced into the plasma as an aqueous solution. The accuracy of the method was checked by analysing a sewage sludge certified reference material (CRM 007-040 Sewage Sludge). The Student's t-test showed that values obtained using slurry nebulisation were close to the certified values at a 95% confidence level. The values of elements Cd 11.1?±?0.8; Cr 37.7?±?3.3; Cu 563.3?±?38.4; Pb 119.2?±?10.1; Zn 729?±?68.2?mg?kg^?1 obtained using this method were comparable with those obtained using the conventional method. The slurry method can, therefore, be successfully applied to the determination of content of each element in sewage sludge with RSD less than 3%, without the need to predissolve them. This could avoid the use of hazardous chemicals, incomplete dissolution and loss of volatile analytes.     

Comparison of analytical methods: ICP-QMS,ICP-SFMS and FF-ET-AAS for the determination of V,Mn, Ni,Cu, As,Sr, Mo,Cd and Pb in ground natural waters

Three analytical methods, namely, inductively coupled plasma sector field mass spectrometry (ICP-SFMS); inductively coupled plasma quadrupole mass spectrometry (ICP-QMS) and filter-furnace electrothermal atomic-absorption spectroscopy (FF-ET-AAS) for the determination of V, Mn, Ni, Cu, As, Sr, Mo, Cd and Pb in ground natural water samples were compared and evaluated for their capacity to provide reliable and precise results. Two certified reference materials (SLEW-3 Estuarine Water; SLRS-4 River Water) were analysed to prove that accurate results could be obtained by using all the listed methods with properly optimised parameters. The limit of detection (LOD) for V, Mn, Ni, Cu, As, Sr, Mo, Cd and Pb provided by the ICP-MS methods ranged from 0.001 to 0.05 µg L^?1. Such LOD proved sufficient for the reliable determination of the listed elements in ground natural waters. However, the LOD of the FF-ET-AAS was approximately two orders of magnitude higher than that of ICP-MS, which made it impossible to quantify V, Mn, Ni, Mo and Pb. The effects of the usage of the collision cell mode in ICP-QMS and of the desolvation system Apex for ICP-SFMS to eliminate oxide ions levels were investigated. For all three analytical methods, the influence of the matrix effect on the results of the determination of the investigated elements using matrix model solution, external calibration and standard addition methods was evaluated. A comparison using a paired Student’s t-test between the results obtained by both ICP-MS methods for V, Mn, Ni, Cu, As, Sr, Mo, Cd and Pb concentrations in ground natural waters showed that there was no significant difference on a 95% confidence level. The precision of the results for ICP-SFMS, ICP-QMS and FF-ET-AAS varied between ~0.5 and 11; 2.5 and 12.5; 3 and 13.5%, respectively. Moreover, ICP-SFMS equipped with the desolvation system APEX proved a better choice for As, Cu and Mn analysis due to its better LOD (0.008, 0.03 and 0.02 µg L^?1, respectively) and precision (S_r ≤ 5.0; 7.5; 9.0%, respectively) compared to ICP-QMS and FF-ET-AAS.     

Nanocluster polyoxomolybdate supported on natural zeolite: a green and recyclable catalyst for epoxidation of alkenes

A heterogeneous catalyst for epoxidation of alkenes has been synthesized by introducing polyoxomolybdate into a natural zeolite as a solid and green support. The prepared catalyst was characterized by FT-IR, inductively coupled plasma optical emission spectrometry (ICP-OES), powder X-ray diffraction (XRD), N₂ absorption–desorption, field emission scanning electron micrograph (FE-SEM) and transmission electron microscopy (TEM). The catalytic investigations disclosed that nanocluster polyoxomolybdate supported on the surface is an active and recyclable catalyst in liquid phase alkene epoxidation in dichloroethane at 80 °C.     

A facile synthesis of boron nanostructures and investigation of their catalytic activity for thermal decomposition of ammonium perchlorate particles

In this research, ultrasound irradiation as a simple method was used to produce boron nanostructures. Reaction conditions such as boron concentration and sonication time show important roles in the size, morphology and growth process of the final products. The boron nanostructures (nanoparticles and nanorods) were characterized by scanning electron microscopy, transmission electron microscopy, X-ray powder diffraction, small-angle X-ray scattering and inductively coupled plasma atomic emission spectroscopy techniques. Primary evaluation of results showed that nanoparticles and nanorods of boron successfully have been prepared with 25–40 and 50–100 nm average particle size, respectively. These nanostructures (nanoparticles and nanorods) were studied as an additive for promoting the thermal decomposition of ammonium perchlorate (AP) particles. Thermochemical decomposition behaviors of treated samples were characterized by thermal gravimetric analysis and differential scanning calorimetry techniques. Also, the kinetic parameters of thermal decomposition processes of pure and treated samples were obtained by nonisothermal methods proposed by Kissinger and Ozawa. However, boron nanoparticles with the smallest average particle size (25–40 nm) have the most significant catalytic effect including the decrease in decomposition temperature of AP + B nanocomposite by 100 °C, increase in the heat of decomposition from 580 to 1354 J g^?1 and decrease in activation energy from 207 to 110 kJ mol^?1.     

Determination of cadmium, chromium and copper in high salt samples by LA-ICP-OES after electrodeposition—preliminary study

A novel method is presented for determination of heavy metal ions in a high-saline matrix. It is based on the electrodeposition of the ions and subsequent laser ablation coupled to inductively coupled plasma optical emission spectrometry (LA-ICP-OES). Three arrangements for electrodeposition were worked out, two of them with stationary working electrodes. Materials for use in the working electrodes, and conditions for electrodeposition of Cd, Cr and Cu (pH, deposition current, time of electrolysis) were studied. Nickel was found to be the best electrode material. The metals accumulate on the surface of electrode and were then evaporated/ablated with a Nd:YAG laser focused into the ICP-OES spectrometer. The detection limits are 0.13 mg?L^?1 for Cd, 0.15 mg?L^?1 for Cu, and 1.9 mg?L^?1 for Cr in case of a stationary bottom working electrode, and 0.25 mg?L^?1 for Cd, 0.05 mg?L^?1 for Cu, 0.8 mg?L^?1 for Cr when using a rotating electrode. The relative standard deviation is in range from 3.8 to 10.3%. Waste water was analyzed in this way by the standard addition method.     

Boron Determination—A Review of Analytical Methods

This paper reviews published methods of sample preparation, determinand purification, and the determination of boron concentration and isotopic composition in a sample. The most common methods for the determination of B concentration are spectrophotometric and plasma-source spectrometric methods. Although most spectrophotometric methods are based on colorimetric reactions of B with azomethine-H, curcumin, or carmine, other colorimetric and fluorometric methods have also been used to some extent. These methods, in general, suffer from numerous interferences and have low sensitivity and precision. Application of nuclear reaction and atomic emission/absorption spectrometric (AES/AAS) methods has remained limited because these methods have poor sensitivity and suffer from serious memory effects and interferences. Among a large number of published nuclear reaction methods only prompt-γ spectrometry has been of practical use. The prompt-γ method can determine B concentration in intact samples, which makes this method especially useful for some medical applications, including boron neutron capture therapy. However, this is a time-consuming method and not suitable for detection of low levels of B. Inductively coupled plasma optical emission spectrometry (ICP-OES) created a new dimension in B determination because of its simplicity, sensitivity, and multielement capability. However, it suffers interferences and is not adequately sensitive for some nutritional and medical applications involving animal tissues that are naturally low in B. All methods involving the measurement of B isotopic composition require a mass spectrometer. Thermal ionization mass spectrometry (TIMS) and secondary ion mass spectrometry (SIMS) have been used to measure isotopic composition of B; however, these methods are time consuming and require extensive sample preparation and purification. Development of inductively coupled plasma mass spectrometry (ICP-MS) not only overcame most of the drawbacks of earlier methods, but also its capabiltiy of measuring B isotopes made possible (1) B concentration determination by isotope dilution, (2) verification of B concentration by isotope fingerprinting in routine analysis, and (3) determination of total B concentration and B isotope ratio for biological tracer studies in the same run. Therefore, plasma source MS appears to be the method of choice among present-day technologies.     

ICP-OES and SEM-EDX Analysis of dust and powder produced by the laser-processing of a Cr-Ni-Steel alloy

In this investigation we compared the analytical results obtained by inductively coupled plasma optical emission spectroscopy (ICP-OES) and a scanning electron microscope with an energy dispersive X-ray analysis system (SEM-EDX). The powder and dust, obtained by laser-processing of CRN-14301 steel, was analysed to classify the powder and dust for its final waste disposal. For this reason we analysed the elemental content of the samples. The samples consisted of a mixture of metals and their oxides.The solid powder and dust was analysed directly by SEM-EDX, the ICP-OES analysis was carried out after the solid was dissolved in an acid solution. Both analytical methods were in good agreement.ICP-OES showed a higher precision and lower detection limit than EDX, but SEM-EDX showed a higher amount of information regarding the sample composition.