Structural,optical, and electrical properties of electron beam evaporated CdSe thin films

CdSe films have been deposited on glass substrates at different substrate temperatures between room temperature and 300 °C. The films exhibited hexagonal structure with preferential orientation in the (002) direction. The crystallinity improved and the grain size increased with temperature. Band gap values are found decreasing from about 1.92 eV to 1.77 eV with increase of the substrate temperature. It is observed that the resistivity decreases continuously with temperature. Laser Raman studies show the presence of 2 LO and 3 LO peaks at 416 cm^‐1 and 625 cm^‐1respectively. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Influence of substrate temperature on the properties of vacuum evaporated InSb films

Indium Antimonide (InSb) thin films were grown onto well cleaned glass substrates at different substrate temperatures (303, 373 and 473 K) by vacuum evaporation. The elemental composition of the deposited InSb film was found to be 52.9% (In) and 47.1% (Sb). X‐ray diffraction studies confirm the polycrystallinity of the films and the films show preferential orientation along the (111) plane. The particle size (D), dislocation density (δ) and strain (ε) were evaluated. The particle size increases with the increase of substrate temperature, which was found to be in the range from 22.36 to 32.59 nm. In Laser Raman study, the presence of longitudinal mode (LO) confirms that the deposited films were having the crystalline nature. Raman peak located at 191.26 cm^–1 shift towards the lower frequencies and narrows with increase in deposition temperature. This indicates that the crystallinity is improved in the films deposited at higher substrate temperatures. Hall measurements indicate that the films were p‐type, having carrier concentration ≅10¹⁶ cm^–3 and mobility (4–7.7) ×10³ cm²/Vs. It is observed that the carrier concentration (N) decreases and the Hall mobility (μ) increases with the increase of substrate temperature. (© 2005 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Influence of selenization temperature on synthesis,morphology, and properties of nanostructured CoSe2 films

Nanostructured cobalt selenide (CoSe₂) thin films were deposited on a glass substrate using the selenization of Co films at different selenization temperatures (300 °C, 400 °C, and 500 °C) in a pure Se vapor for two hours. The morphology and structure of the as‐deposited films shows that the film morphology and crystallinity are affected by the selenization temperature. Increasing the selenization temperature from 300 °C to 400 °C and 500 °C results in a change in the surface and cross sectional morphology. At 300 °C, the Co films have an almost amorphous structure, while at temperatures of 400 and 500 °C, the Co films have a crystalline nanostructure with bilayered morphology. Optical analyses of the CoSe₂ films at 500 °C show a large absorption (α > 1.0 × 10⁵ cm⁻¹) and a direct band gap (∼1.0 eV).     

Effect of substrate temperature on polycrystalline Cd0.9Zn0.1Te thin films studied by Raman scattering spectroscopy

Cd_0.9Zn_0.1Te thin films were prepared by vacuum evaporation onto well‐cleaned glass substrates maintained at 300, 373 and 473 K. X‐ray diffraction studies revealed that the films have zinc blende structure with preferential (111) orientation. Raman peak of the room temperature deposited film appeared at 140.30 cm^‐1 and 159.65 cm^‐1 were for the transverse optic (TO) and longitudinal optic (LO) phonons respectively. The XRD patterns of the higher substrate temperature deposited films exhibited an improvement in the crystallinity of the films. The Raman peak intensity increases and the FWHM decreases for the films deposited at higher substrate temperature. (© 2004 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structural,optical and photoconductive properties of electron beam evaporated CdSxSe1‐x films

CdS_xSe_1‐x films were deposited by the electron beam evaporation technique on glass substrates at different temperatures in the range 30 – 300 °C using the laboratory synthesized powders of different composition. The films exhibited hexagonal structure and the lattice parameters shifted from CdSe to CdS side as the composition changed from CdSe to CdS side. The bandgap of the films increased from 1.68 to 2.41 eV as the concentration of CdS increased. The root‐mean‐roughness (RMS) values are 3.4, 2.6, 1.2 and 0.6 nm as the composition of the films shifted towards CdS side. The conductivity varies from 30 Ωcm^‐1 to 480 Ωcm^‐1 as the ‘x’ value increases from 0 to 1. The films exhibited photosensitivity. The PL spectrum shifts towards lower energies with decreasing x, due to the decrease of the fundamental gap with Se composition. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Influence of density of states on optical properties of GaSe thin film

A systematic investigation on the effect of substrate temperature on the structure, optical absorption and density of states of vacuum evaporated gallium monoselenide (GaSe) thin films is reported. The X‐ray diffraction analysis shows an occurrence of amorphous to polycrystalline transformation in the films deposited at higher‐temperature substrates (573K). The compositional analysis is made with Auger Electron Spectroscopy (AES). The thickness of the film (175nm) is measured by a multiple beam interferometery. Optical characteristics of the GaSe sample have been analyzed using spectrophotometer in the photon energy range of 1.0 ‐ 4 eV. The absorption mechanism has been recognized and the allowed indirect as well as forbidden direct transitions have been found. As‐deposited films show two indirect and allowed transitions due to spin‐orbit splitting of the valence band, as reported here for the first time. Low field conduction have enabled us to determine the density of states in amorphous and poly‐GaSe films. The amorphous and polycrystalline GaSe thin films have localized states density values of N (E_F) = 1.686 × 10¹⁷ cm^‐3 eV^‐1 and 1.257 × 10¹⁵ cm^‐3 eV^‐1 respectively. The experimental results are interpreted in terms of variations in the density of localized states due to progressive decrease of the unsaturated bonds during deposition. (© 2004 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Effect of substrate temperature on the properties of vacuum evaporated indium selenide thin films

Thin films of InSe were obtained by thermal evaporation techniques on glass substrates maintained at various temperatures (T_sb = 30°, 400°C). X‐ray diffraction analysis showed the occurrence of amorphous to polycrystalline transformation in the films deposited at higher substrate temperature (400°C). The polycrystalline films were found to have a hexagonal lattice. Compositions of these films have been characterized by EDAX and the surface analysis by scanning electron microscopy. Optical properties of the films, investigated by using spectrophotometer transmittance spectra in the wavelength range (300 – 1100 nm), were explained in terms of substrate temperatures. Films formed at room temperature showed an optical band gap (E_g^opt) 1.56 eV; where as the films formed at 400°C were found to have a E_g^opt of 1.92 eV. The increase in the value of E_g^opt with T_sb treatment is interpreted in terms of the density of states model as proposed by Mott and Davis. The analysis of current ‐Voltage characteristics, based on space charge limited currents (SCLC) measurements, confirms the exponential decrease of density of states from the conduction band edge towards the Fermi level for both the amorphous and polycrystalline films. (© 2005 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Carrier Scattering Mechanisms in GaS0.5Se0.5 Layered Crystals

Systematic dark electrical resistivity and Hall mobility measurements have been carried out in the temperature range 150‐400 K on n‐type GaS_0.5Se_0.5 layered crystals. The analysis of temperature dependent electrical resistivity and carrier concentration reveals the extrinsic type of conduction with a donor impurity level located at 0.44 eV, donor and acceptor concentrations of 3.4 ×10¹⁷ and 4.1×10¹⁶ cm^‐3, respectively, and an electron effective mass of 0.41 m₀. The Hall mobility is limited by the electron‐phonon short‐range interactions scattering at high temperatures combined with the ionized impurity scattering at low temperatures. The electron‐phonon short‐range interactions scattering mobility analysis reveals an electron‐phonon coupling constant of 0.25 and conduction band deformation potential of 5.57 eV/Å.     

Effect of annealing on the properties of chemical bath deposited nanorods of CdSe thin films

Cadmium selenide (CdSe) thin films have been deposited by chemical bath deposition (CBD) on a glass substrate and they are annealed at 450 °C for 1 h. Scanning electron microscopic (SEM) image of as‐deposited CdSe shows the spherical shaped grains distributed over entire glass substrate. When it is annealed at 450 °C, clusters of nano‐rods with star shaped grains are formed. The X‐ray diffraction (XRD) study of the as‐deposited films exhibits a polycrystalline nature and it undergoes a structural phase transition from the metastable cubic to the stable hexagonal phase when annealed at 450 °C. Optical band gap of as‐deposited films (2.0 eV) has a blue shift with respect to the bulk value (1.7 eV) due to quantum confinement. The band gap energies of the films are decreased from 2.0 eV to 1.9 eV due to annealing at the temperature of 450 °C. The electrical resistivity, Hall mobility and carrier concentration of as‐deposited and annealed films are determined.     

Spray pyrolysis deposition and characterization of highly (100) oriented magnesium oxide thin films

Transparent dielectric thin films of MgO has been deposited on quartz substrates at different temperatures between 400 and 600°C by a pneumatic spray pyrolysis technique using Mg(CH₃COO)₂·4H₂O as a single molecular precursor. The thermal behavior of the precursor magnesium acetate is described in the results of thermogravimetry analysis (TGA) and differential thermal analysis (DTA). The prepared films are reproducible, adherent to the substrate, pinhole free and uniform. Amongst the different spray process parameters, the substrate temperature effect has been optimized for obtaining single crystalline and transparent MgO thin films. The films crystallize in a cubic structure and X‐ray diffraction measurements have shown that the polycrystalline MgO films prepared at 500°C with (100) and (110) orientations are changed to (100) preferred orientation at 600°C. The MgO phase formation was also confirmed with the recorded Fourier Transform Infrared (FTIR) results. The films deposited at 600°C exhibited highest optical transmittivity (>80%) and the direct band gap energy was found to vary from 4.50 to 5.25 eV with a rise in substrate temperature from 500 to 600°C. The measured sheet resistance and the resistivity of the film prepared at 600°C were respectively 10¹³Ω/□ and 2.06x10⁷Ω cm. The surface morphology of the prepared MgO thin films was examined by atomic force microscopy. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Nanocrystalline TiO2 films studied by optical, XRD and FTIR spectroscopy

We report the deposition of thin titanium dioxide films on Si(1 0 0) and silica glass at low temperatures between 200 and 350 °C by a technique of ultraviolet-assisted injection liquid source chemical vapor deposition (UVILS-CVD) with 222 nm radiation. The composition and optical properties of the films deposited have been studied using a variety of standard characterisation methods. A strong absorption peak around 438 cm⁻¹, corresponding to Ti-O stretching vibration, was observed by Fourier transform infrared spectroscopy for different deposition temperatures. Nanostructured films on Si wafers were observed by atomic force microscopy while X-ray diffraction results showed that crystalline TiO₂ layers could be formed at deposition temperatures as low as 210 °C. The deposition kinetics and influence of the substrate temperature on the film are discussed. The activation energy for this photo-CVD process at temperatures between 200 and 350 °C was found to be 0.435 eV. This is much lower than the value (E_a=5.64 eV) obtained by conventional thermal CVD. The thicknesses of the films grown, from several nanometers to micrometers can be accurately controlled by changing the number of drops introduced by the injection liquid source. Under optimum deposition conditions, refractive index values as high as 2.5 and optical transmittance of between 85% and 90% in the visible region of the spectrum can be obtained.     

Influence of the substrate temperature on the structural,optical, and electrical properties of tin selenide thin films deposited by thermal evaporation method

Thin films of tin selenide (SnSe) were deposited on sodalime glass substrates, which were held at different temperatures in the range of 350‐550 K, from the pulverized compound material using thermal evaporation method. The effect of substrate temperature (T_s) on the structural, morphological, optical, and electrical properties of the films were investigated using x‐ray diffraction analysis (XRD), scanning electron microscopy (SEM), transmission measurements, and Hall‐effect characterization techniques. The temperature dependence of the resistance of the films was also studied in the temperature range of 80‐330 K. The XRD spectra and the SEM image analyses suggest that the polycrystalline thin films having uniform distribution of grains along the (111) diffraction plane was obtained at all T_s. With the increase of T_s the intensity of the diffraction peaks increased and well‐resolved peaks at 550 K, substrate temperature, were obtained. The analysis of the data of the optical transmission spectra suggests that the films had energy band gap in the range of 1.38‐1.18 eV. Hall‐effect measurements revealed the resistivity of films in the range 112‐20 Ω cm for films deposited at different T_s. The activation energy for films deposited at different T_s was in the range of 0.14 eV‐0.28 eV as derived from the analysis of the data of low‐temperature resistivity measurements. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Electrical properties of PbxSn1‐xS thin films prepared by hot wall deposition method

The Pb_xSn_1‐xS (x = 0 – 0.25) thin films were prepared on glass substrates by hot wall vacuum deposition. The films were polycrystalline monophase in nature and had orthorhombic crystal structure. The thickness of the films was about 2‐3 μm. The temperature dependences of the conductivity were measured in the temperature range from 150 to 420 K. The films revealed p‐type of conductivity. The Seebeck coefficient and conductivity values of the films was in the range of α = 6 – 360 μV/K and σ = 4.8×10^‐5 – 1.5×10^‐2 Ω^‐1·cm^‐1, respectively, at room temperature depending on concentration of the lead in the films. The lead atoms created the substitution defects Pb_Sn in the crystal lattice of the Pb_xSn_1‐xS. These defects formed the donor energy levels in the band gap. The activation energy of the films increased in the range ΔE_a = 0.121 – 0.283 eV with increasing of the lead concentration. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Electrical and photoconductive properties of GaS0.75Se0.25 mixed crystals

The conductivity, mobility, photoconductivity and photo response measurements in GaS_0.75Se_0.25 mixed crystals were carried out in the temperature range of 150‐450 K. The room temperature conductivity, mobility and electron concentration values were 10^‐9 (Ω‐cm)^‐1, 48 cm²V^‐1s^‐1 and ∼10⁹ cm^‐3, respectively. Two donor levels were obtained from temperature‐dependent conductivity and carrier concentration, located at energies of about 755 and 465 meV below the conduction band. Single donor‐single acceptor analysis yields the same donor level at 465 meV with donor and acceptor concentrations of 8.7 × 10¹⁴ and 5.3 × 10¹³ cm^‐3, respectively. The mobility‐temperature dependence shows that ionized impurity scattering dominates the conduction up to the temperature 310 K with different temperature exponent, while above this critical temperature; the phonon scattering is dominant conduction mechanism. From the photo‐response spectra, the maximum photocurrent was observed for all the samples at 2.42 eV, and varied slightly with temperature. Moreover, the photocurrent‐light intensity dependence in these crystals obeys the power law, I_ph ∝ ϕ^γ with γ between 1.7 and 2.0 for various applied fields and temperatures. (© 2005 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Correlation between growth orientation and growth temperature for bismuth tri‐iodide films

This paper reports the growth of bismuth tri‐iodide thick films intended for direct and digital X‐ray imaging. Films were grown by the vertical physical vapor deposition method, onto glass substrates 2″x 2″ in size, with gold previously deposited as rear electrode. The film thickness was up to 33 μm (±5 %). Optical microscopy and SEM were performed on the films and grain size resulted to be up to 40 μm. A strong correlation was found between the microcrystals growth orientation and the growth temperature. At low temperatures, microcrystals grow with their c axis parallel to the substrate, whereas at higher temperatures, they grow with their c axis perpendicular to the substrate. The higher the growth temperature, the lower the dark current of the film, and the higher the resistivity, which was from 10¹³ to 10¹⁵ Ωcm. A sensitivity to X‐rays of 6.9 nC/R.cm² was measured irradiating the films with X‐rays from a mamographer. Film properties were correlated with the growth temperature, with previous results for bismuth tri‐iodide films and monocrystals and with data for films of alternative materials such as lead and mercuric iodide. (© 2004 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Effect of substrate temperature on the properties of reactively sputtered TiN/NbN multilayers

TiN/NbN multilayer coatings were deposited with various substrate temperatures by DC reactive magnetron sputtering method onto Si (111) and glass substrates. The effect of substrate temperature on the structural and optical properties of TiN/NbN multilayers was investigated by X‐ray diffraction, X‐ray photoelectron spectroscopy, Field emission scanning electron microscopy and Photoluminescence measurements. The composition was analyzed by X‐ray photoelectron spectroscopy. X‐ray diffraction results showed that the layers crystallized in cubic structure for TiN and hexagonal structure for NbN. It was found that grain size increased with increase in substrate temperature. The surface morphology of the TiN/NbN thin films showed a dense and smooth surface with substrate temperature upto 200 °C but after 300 °C, the grains became larger and coarse surface was observed. The TiN/NbN multilayer coatings exhibited the characteristic peaks centered at 180, 210 and 560 cm^‐1. Red band emission peaks were observed in the wavelength range of 700‐710 nm. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

The influence of N2 flow rate and substrate temperature on Ti1‐xAlxN thin films

Titanium aluminium nitride (Ti_1‐xAl_xN) films have been deposited on silicon (111) substrate at a N₂ flow rate of 2 sccm and 20 sccm and at a substrate temperature of 773 K and at a N₂ flow rate of 2 sccm and at a substrate temperature of 873 K by reactive DC magnetron sputtering technique. The effect of N₂ flow rate and substrate temperature on the grain size and surface roughness of the deposited films have been investigated. The films have been analysed by X‐ray diffraction (XRD) and atomic force microscopy (AFM). The films were found to be nanocrystalline. While the grain size of the films decreases with increasing N₂ flow rate and decreases with increasing substrate temperature, the surface roughness of the films decreases with increasing N₂ flow rate and increases with increasing temperature. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Microstructural,optical and electrical properties of GeO2 thin films prepared by sol‐gel method

GeO₂ thin films were prepared by sol‐gel method on ITO/Glass substrate. The electrical and optical properties and the microstructures of these films were investigated with special emphasis on the effects of an annealing treatment in ambient air. The films were annealed at various temperatures from 500 °C to 700 °C. Structural analysis through X‐ray diffraction (XRD) and atomic force microscope (AFM) showed that surface structure and morphological characteristics were sensitive to the treatment conditions. The optical transmittance spectra of the GeO₂/ITO/Glass were measured using a UV‐visible spectrophotometer. All films exhibited GeO₂ (101) orientation perpendicular to the substrate surface where the grain size increased with increasing annealing temperature. The optical transmittance spectroscopy further revealed high transparency (over 70 %) in the wave range 400 – 800 nm of the visible region. At an annealing temperature level of 700 °C, the GeO₂ films were found to possess a leakage current density of 1.31×10^‐6A/cm² at an electrical field of 20 kV/cm. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Temperature dependence of Raman‐active mode frequencies and linewidths in TlGaSe2 layered crystals

Raman spectra of TlGaSe₂ crystal at different temperatures are discussed. The temperature dependence of frequency shifts and linewidths of the Raman peaks in the frequency region of 10‐320 cm^‐1 have been measured in the range from 50 to 320 K. The analysis of the experimental data showed that the temperature dependencies of phonon frequencies and linewidths are well described by considering the contributions from thermal expansion and lattice anharmonicity. The anharmonic contribution (phonon‐phonon coupling) is found to be due to three‐phonon processes. (© 2005 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Influence of substrate temperature on the structure of ZnO:Al thin films

ZnO: Al films were prepared using low cost spray pyrolysis technique. The dependence of the physical properties on the substrate temperature was studied. The best films obtained at 500°C substrate temperature with preferred [002] orientation. The sheet resistance decreases with increased substrate temperature, and values as low as R_sh = 207 Ω/cm² are reached for substrate temperature of 500°C. The optical transmittance of films increased by increasing the substrate temperature and received to 75% at 500°C. (© 2007 WILEY ‐VCH Verlag GmbH & Co. KGaA, Weinheim)