Structural and optical properties of ZnO nanopowder prepared by microwave-assisted synthesis

We report the characterization of nano-size zinc oxide (ZnO) powder synthesized via microwave-assisted heating of Zn(CH₃COO)₂·2H₂O and NaHCO₃ solution with deionized water (DI water) as the solvent. The as-synthesized ZnO powder was calcined at temperatures from 400 to 800 °C for 8 h. The X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) spectra revealed pure wurtzite structure for the ZnO nanopowder (NP) calcined at 800 °C. Scanning electron microscopy (SEM) images showed increasing size ZnO NP with uniform size distribution with increase in calcination temperature. Significant UV emission at about 373 nm has been observed in the photoluminescence (PL) spectra of the as-synthesized and calcined ZnO NP. Our results showed enhanced PL intensity with a reduced full-width at half-maximum (FWHM) for ZnO NP synthesized at higher calcination temperature.     

Synthesis and bioactivity of highly ordered TiO2 nanotube arrays

The highly ordered TiO₂ nanotube arrays were fabricated by potentiostatic anodization of Ti foils in fluorinated dimethyl sulfoxide (DMSO). TiO₂ nanotube arrays are formed using a 40 V anodization potential for 24 h, with a length of 12 μm, diameter of 170 nm and aspect ration of about 70. The as-prepared nanotubes are amorphous, but can be crystallized as the heat treatment temperature increases. Anatase phase appears at a temperature of about 300 °C, then transforms to rutile phase at about 600 °C. After heat treatment at 500 °C and soaking in SBF for 14d, a thick apatite layer of about 13 μm covers the whole surface of TiO₂ nanotube arrays, indicating their excellent in vitro bioactivity, which is mainly attributed to their high specific surface area and the anatase phase.     

Photocatalytic activity of multielement doped TiO2 in the degradation of congo red

TiO₂ although considered a promising photocatalyst for the degradation of aqueous pollutants, it suffers from poor absorption in the visible region and hence requires ultraviolet (UV) light for activation. To make TiO₂ a visible active photocatalyst, multielement (C, N, B, and F) doping has been done. The synthesised CNBF/TiO₂ catalysts were calcined at different temperatures and characterized by XRD, BET surface area, UV DRS, XPS, HRSEM-EDAX, and TEM techniques. These catalysts found to show less band gap values when compared to bare TiO₂. These catalysts were tested for their catalytic activity towards the degradation of a textile dye - congo red (CR) under different reaction conditions. It was found that the photocatalytic activity was dependent on both doping of multielement and the calcination temperature of CNBF/TiO₂. The co-doped catalysts which were calcined at 400 °C and 600 °C (100% intensity in anatase phase) were found to be the best catalysts (100% decolourisation of CR in 21/2 h and 2 h respectively). TOC analysis carried out for the samples at the reaction time of 5 h showed very high percentage (83%) degradation of CR over CNBF/TiO₂ catalysts calcined at 600 °C when compared to the other catalysts calcined at different temperatures. CNBF/TiO₂ (1000 °C) showed very less photocatalytic activity due to the formation of rutile phase.     

Thermal stability of HfO2 nanotube arrays

Thermal stability of highly ordered hafnium oxide (HfO₂) nanotube arrays prepared through an electrochemical anodization method in the presence of ammonium fluoride is investigated in a temperature range of room temperature to 900 °C in flowing argon atmosphere. The formation of the HfO₂ nanotube arrays was monitored by current density transient characteristics during anodization of hafnium metal foil. Morphologies of the as-grown and post-annealed HfO₂ nanotube arrays were analyzed by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Although monoclinic HfO₂ is thermally stable up to 2000 K in bulk, the morphology of HfO₂ nanotube arrays degraded at 900 °C. A detailed X-ray photoelectron spectroscopy (XPS) study revealed that the thermal treatment significantly impacted the composition and the chemical environment of the core elements (Hf and O), as well as F content coming from the electrolyte. Possible reasons for the degradation of the nanotube at high temperature were discussed based on XPS study and possible future improvements have also been suggested. Moreover, dielectric measurements were carried out on both the as-grown amorphous film and 500 °C post-annealed crystalline film. This study will help us to understand the temperature impact on the morphology of nanotube arrays, which is important to its further applications at elevated temperatures.     

Effect of annealing temperature on the structural, photoluminescence and magnetic properties of sol-gel derived Magnetoplumbite-type (M-type) hexagonal strontium ferrite

Magnetoplumbite-type (M-type) hexagonal strontium ferrite particles were synthesized via sol-gel technique employing ethylene glycol as the gel precursor at two different calcination temperatures (800 and 1000 °C). Structural properties were systematically investigated via X-ray diffraction (XRD), field emission scanning electron microscopy, high resolution transmission electron microscopy (HRTEM), energy dispersive spectroscopy (EDS), thermogravimetric analysis (TGA), photoluminescence spectrophotometry and superconducting quantum interference device magnetometer. XRD results showed that the sample synthesized at 1000 °C was of single-phase with a space group of P6₃/mmc and lattice cell parameter values of a=5.882 Å and c=23.048 Å. EDS confirmed the composition of strontium ferrite calcined at 1000 °C being mainly of M-type SrFe₁₂O₁₉ with HRTEM micrographs confirming the ferrites exhibiting M-type long range ordering along the c-axis of the crystal structure. The photoluminescence (PL) property of strontium ferrite was examined at excitation wavelengths of 260 and 270 nm with significant PL emission peaks centered at 350 nm being detected. Strontium ferrite annealed at higher temperature (1000 °C) was found to have grown into larger particle size, having higher content of oxygen vacancies and exhibited 83-85% more intense PL. Both the as-prepared strontium ferrites exhibited significant oxygen vacancies defect structures, which were verified via TGA. Higher calcination temperature turned strontium ferrite into a softer ferrite.     

Effect of phase structures on the formation rate of hydroxyl radicals on the surface of TiO2

To study the relationship between the phase structures of TiO₂ and the photoinduced hydroxyl radicals (OH), TiO₂ nanocrystallines were synthesized by a hydrolysis-precipitate method using tetrabutylorthotitanate (TBOT) as precursor, and then calcined at 450, 600, 700, 800 and 900 °C for 2 h, respectively. The calcined samples were characterized by X-ray diffraction and N₂ sorption. The formation rate of OH on the surface of UV-illuminated TiO₂ was detected by the photoluminescence (PL) technique using terephthalic acid as a probe molecule. The results show that with increasing calcined temperatures, the amorphous (Am) TiO₂ precursor begins to turn into anatase (A) at 450 °C and rutile (R) phase appears at 600 °C, which is completely turned into the rutile phase at 900 °C. The BET specific surface areas of the catalyst decrease as the calcined temperatures increase. TiO₂ sample calcined at 600 °C, with a mixed phase of anatase and rutile, shows the highestOH formation rate, and the order of the OH formation rate is as follows: A+R>A>R>Am. Phase structures of TiO₂ play a more important role than specific surface areas in the OH formation rate. Two phase structure of anatase and rutile with a proper ratio is beneficial to the OH formation due to decrease of the combination rate of photo-generated electrons and holes. Our experimental result implies that the mixed phase of anatase and rutile can markedly enhance the photocatalytic activity of TiO₂.     

Comparison of photocatalytic performance of anatase TiO2 prepared by low and high temperature route

Anatase TiO₂ was prepared by a facile sol-gel method at low temperature through tailoring the pH of sol-gel without calcination. As a control, anatase TiO₂ was also synthesized by the conventional sol-gel process, in which calcination at 500 °C was required to transform the amorphous oxide into highly crystalline anatase. As-prepared samples were characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and photoluminescence spectroscopy (PL). Their photocatalytic activities were evaluated by degradation of methyl orange under UV light irradiation. On the basis of experiment results, it could be concluded that TiO₂ prepared by low temperature route showed more advantages in small particle size, highly dispersion nature, abundance of surface hydroxyl groups, strong PL signal, and high photocatalytic activity over TiO₂ obtained by the conventional sol-gel process. Furthermore, the reason of the former possessing higher photocatalytic activity was discussed.     

Properties of mesoporous tungstosilicic acid/titania composites prepared by sol-gel method

The tungstosilicic acid/titania composites were prepared by the sol-gel method. Titanium isopropoxide was used as titania precursor, and urea as a low-cost template. The tungstosilicic acid (TSA) was added in the same step as that in which titania hydrogel is formed. The TSA-modified samples only showed the characteristic peaks of anatase phase of titanium oxide in the XRD patterns, indicating that the presence of TSA retarded the crystallization of the anatase phase and its transformation into the rutile phase. Spherical particles with sizes between 200 and 700 nm, formed by aggregation of nanoparticle aggregates (4-50 nm in size), were observed. The particle size increased when the TSA content was raised and also increased slightly with the thermal treatment temperature. Mesoporous materials were obtained, with a mean pore diameter higher than 3.1 nm. Both the increase of the TSA concentration in the solid and the calcination temperature led to a decrease in the specific surface area of the samples. The main heteropolyoxometallate species present in the composites is the [SiW₁₂O₄₀]⁴⁻ anion for the composites calcined up to 500 °C. The band gap energy decreased as a result of the introduction of TSA into the titania matrix, though it remained almost constant with the calcination temperature increase.     

Hydrothermal preparation and photoluminescent properties of MgAl2O4: Eu spinel nanocrystals

Nanoplates of the MgAl₂O₄ spinel doped with Eu³⁺ ions were prepared by a microwave assisted hydrothermal method. Structural properties of the precursor calcined at 700 and 1000 ^oC powders were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). According to the obtained XRD patterns the formation of single-phase spinels after calcination was confirmed. The average spinel particle size was determined to be 11 nm after calcination at 700 °C and it increased up to 14 nm after calcination at 1000 °C. The photoluminescent properties of prepared powders with different Eu³⁺ ion concentrations (0-5% mol) were investigated using excitation and emission spectroscopy at room and low temperatures (77 K).     

Effect of annealing on TiO2 nanoparticles

TiO₂ nanoparticles have been prepared by simple chemical precipitation method and annealed at different temperatures. The as-prepared TiO₂ are amorphous, and they transform into anatase phase on annealing at 450 °C, and rutile phase on annealing at 900 °C. The X-ray diffraction results showed that TiO₂ nanoparticles with grain size in the range of 21–24 nm for anatase phase and 69–74 nm for rutile phase have been obtained. FESEM images show the formation of TiO₂ nanoparticles with small size in structure. The FTIR and Raman spectra exhibited peaks corresponding to the anatase and rutile structure phases of TiO₂. Optical absorption studies reveal that the absorption edge shifts towards longer wavelength (red shift) with increase of annealing temperature.     

Preparation of titania hollow spheres by catalyst-free hydrothermal method and their high thermal stabilities

TiO₂ hollow spheres have been prepared by hydrothermal method using carbon spheres as hard templates based on template-directed deposition and calcination in order to remove templates. The morphology and structure of samples were systematically characterized by using various techniques, including XRD, zeta analyzer, SEM, TEM, DRS and FTIR. In this approach, the anatase phase was retained for temperatures up to 900 °C. Moreover, negative charged titania is deposited onto the negative charged surface of carbon spheres, which is proved by nanoparticle size analyzer. Therefore, a possible formation mechanism of TiO₂ hollow spheres was proposed. TiO₂ hollow spheres calcined at 550 °C exhibited the superior photocatalytic activity for the degradation of Rhodamine B, 2.9 times greater than that of Degussa P25. Furthermore, thermal stability of TiO₂ hollow spheres was examined. Fortunately, we found that hollow structures could still be visible distinctly after calcining at 900 °C.     

Synthesis and characterization of nanostructured strontium hexaferrite thin films by the sol–gel method

Nanostructured single phase strontium hexaferrite, SrFe₁₂O₁₉, thin films have been synthesized on the (100) silicon substrate using a spin coating sol–gel process. The thin films with various Fe/Sr molar ratios of 8–12 were calcined at different temperatures from 500 to 900 °C. The composition, microstructure and magnetic properties of the SrFe₁₂O₁₉ thin films were characterized using Fourier transform infrared spectroscopy, differential thermal analysis, thermogravimetry, X-ray diffraction, electron microscopy and vibrating sample magnetometer. The results showed that the optimum molar ratio for Fe/Sr was 10 at which the lowest calcination temperature to obtain the single phase strontium hexaferrite thin film was 800 °C. The magnetic measurements revealed that the sample with Fe/Sr molar ratio of 10, exhibited higher saturation magnetization (267.5 emu/cm³) and coercivity (4290 Oe) in comparison with those synthesized under other Fe/Sr molar ratios.     

Preparation and characterization of Fe-doped TiO2 on fly ash cenospheres for photocatalytic application

Fe³⁺-doped TiO₂ film deposited on fly ash cenosphere (Fe-TiO₂/FAC) was successfully synthesized by the sol-gel method. These fresh photocatalysts were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and thermogravimetric analyses (TGA). The XRD results showed that Fe element can maintain metastable anatase phase of TiO₂, and effect of temperature showed rutile phase appears in 650 °C for 0.01% Fe-TiO₂/FAC. The SEM analysis revealed the Fe-TiO₂ films on the surface of a fly ash cenosphere with a thickness of 2 μm. The absorption threshold of Fe-TiO₂/FACs shifted to a longer wavelength compared to the photocatalyst without Fe³⁺-doping in the UV-vis absorption spectra. The photocatalytic activity and kinetics of Fe-TiO₂/FAC with varying the iron content and the calcination temperatures were investigated by measuring the photodegradation of methyl blue (MB) during visible light irradiation. Compared with TiO₂/FAC and Fe³⁺-doped TiO₂ powder (Fe-TiO₂), the degradation ratio using Fe-TiO₂/FAC increased by 33% and 30%, respectively, and the best calcined temperature was 450 °C and the optimum doping of Fe/Ti molar ratio was 0.01%. The Fe-TiO₂/FAC particles can float in water due to the low density of FAC in favor of phase separation to recover these photocatalyst after the reaction, and the recovery test shows that calcination contributes to regaining photocatalytic activity of Fe-TiO₂/FAC photocatalyst.     

Microwave-assisted synthesis of SrFe12O19 hexaferrites

Ultra-fine and homogeneous SrFe₁₂O₁₉ hexaferrites were synthesized by a microwave-assisted calcination route. The calcined precursors were prepared by a sol-gel auto-combustion method using Fe(NO₃)₃·9H₂O, Sr(NO₃)₂ and citric acid as starting materials. The structures, powder morphology and magnetic properties of the products were characterized by X-ray diffraction, scanning electron microscope and vibrating sample magnetometer. The results showed that microwaves are helpful to reduce the calcination temperature and shorten the calcination time. The ferrites with saturation magnetization, remanence and intrinsic coercivity of 54.80 emu/g, 29.52 emu/g and 5261 Oe, respectively, were obtained in samples calcined at 800 °C for 80 min.     

Eu(III) incorporation in sol-gel aluminum-yttrium matrix by non-hydrolytic route

The sol-gel method using metal alkoxide has been investigated to prepare aluminum-yttrium oxide as yttrium-aluminum garnet (YAG) matrix composite fiber. In this paper we investigate the influence of yttrium content and temperature in the synthesis of Eu(III)-doped aluminum-yttrium oxide by non-hydrolytic sol-gel route. The formation process and the local structure of the samples were discussed by means of X-ray diffraction (XRD), thermogravimetric analysis (TGA), scanning electron microscopy (SEM) and photoluminescence (PL) spectroscopy. For temperatures around 800 °C, initial crystallization was observed and the phases Y₄Al₂O₉ (YAM) and Y₃Al₅O₁₂ (YAG) appear. For samples treated at 800 and 1500 °C the emission spectra display preferentially the f-f transitions characteristic of the YAM monoclinic phase, whereas the YAG cubic appears as the favored phase at 1100 °C, in accordance with the Eu(III) centrosymmetrical local site.     

Disorder-dependent photoluminescence in Ba0.8Ca0.2TiO3 at room temperature

The photoluminescence (PL) emission in structurally disordered Ba_0.8Ca_0.2TiO₃ (BCT20) powders was observed at room temperature with laser excitation at lines 355 and 460 nm. The structural evolution perovskite-like titanate BCT20 powders prepared by a soft chemical processing at different annealing temperatures were accompanied by X-ray diffraction (XRD) and X-ray absorption near-edge structure (XANES). Intermediate oxycarbonate phase was identified and your influence with PL emission was discarding. BCT20 annealed at 500 °C displays intense PL emission. The results indicate relationship between broad PL band and order-disorder degree.     

Magnetic properties of MnO nanocrystals dispersed in a silica matrix

Magnetic nanocrystalline MnO particles have been synthesized in a silica glass matrix by the sol-gel method at calcination temperatures up to 1000 °C. EPR spectra of 0.1 mol% MnO doped silica gel and glasses studied in the temperature range 10-290 K show with the exception of those samples calcined at 900 and 1000 °C 6-line characteristic Mn(II) hyperfine (HF) lines. Additionally five spin-forbidden doublets have been observed at 100 K and below. Small spreads in spin Hamiltonian parameters (D and E) imply that the ligand field environments of Mn(II) ions embedded in the silica glass are nearly uniform. Monotonous decrease in HF linewidth in going from 120 °C gel to 800 °C calcined glass has been interpreted as the continuous decrease in population of isolated Mn²⁺ ions in silica glass matrix resulting in the decrease of magnetic dipolar interactions leading to the observed decrease in HF linewidth. XRD and TEM of sample calcined at 1000 °C shows the presence of nanocrystals of MnO having orthorhombic crystalline phase and sizes about 10 nm. The thermal behavior of magnetization (zero-field-cooled and field-cooled) and magnetic hysteresis of MnO nanocrystals in the 5-300 K temperature interval have demonstrated that the MnO nanocrystals display superparamagnetic-ferromagnetic transition at low temperatures. X-band EPR linewidth data plotted versus inverse of temperature (1/T) for samples calcined at 900 and 1000 °C (EPR recorded in the vicinity of 0.35 T applied field) depict similar transitions.     

Effect of heat treatment on morphology, crystalline structure and photocatalysis properties of TiO2 nanotubes on Ti substrate and freestanding membrane

Highly ordered titanium oxide (TiO₂) nanotubes were prepared by electrolytic anodization of titanium electrodes. Morphological evolution and phase transformations of TiO₂ nanotubes on a Ti substrate and that of freestanding TiO₂ membranes during the calcinations process were studied by scanning electron microscopy, transmission electron microscopy, and X-ray diffraction microscopy. The detailed results and mechanisms on the morphology and crystalline structure were presented. Our results show that a compact layer exists between the tubular layer and Ti substrate at 600 °C, and the length of the nanotubes shortens dramatically at 750 °C. The freestanding membranes have many particles on their tubes during calcinations from 450 to 900 °C. The TiO₂ nanotubes on the Ti substrate transform to rutile crystals at 600 °C, while the freestanding TiO₂ membranes retain an anatase crystal with increasing temperature to 800 °C. The photocatalytic activity of TiO₂ nanotubes on a Ti substrate annealed at different temperatures was investigated by the degradation of methyl orange in aqueous solution under UV light irradiation. Due to the anatase crystals in the tubular layer and rutile crystals in the compact layer, TiO₂ nanotubes annealed at 450 °C with pure anatase crystals have a better photocatalytic activity than those annealed at 600 °C or 750 °C.     

Synthesis and characterization of magnetic diphase ZnFe(2)O(4) /γ-Fe(2)O(3) electrospun fibers

Magnetic nanofibers of ZnFe₂O₄/γ-Fe₂O₃ composite were synthesized by electrospinning from a sol-gel solution containing a molar ratio (Fe/Zn) of 3. The effects of the calcination temperature on phase composition, particle size and magnetic properties have been investigated. Zinc ferrite fibers were obtained by calcinating the electrospun fibers in air from 300 to 800 °C and characterized by thermogravimetric analyses, Fourier transformed infrared spectroscopy, X-ray photoemission spectroscopy, X-ray diffraction, vibration sample magnetometry and magnetic force microscopy. The resulting fibers, with diameters ranging from 90 to 150 nm, were ferrimagnetic with high saturation magnetization as compared to bulk. An increase in the calcination temperature resulted in an increase in particle size and saturation magnetization. The observed increase in saturation magnetization was most likely due to the formation and growth of ZnFe₂O₄/γ-Fe₂O₃ diphase crystals. The highest saturation magnetization (45 emu/g) was obtained for fibers calcined at 800 °C.     

Effect of post heat treatment on microstructure and photocatalytic activities of TiO2 nanoribbons

Low-dimensional TiO₂ nanoribbons were synthesized by a simple one-step hydrothermal method. The TiO₂ nanoribbons were calcined over the temperature range 200-800 °C in order to enhance their photocatalytic properties by altering their crystal phase and increasing crystallization. Effects of hydrothermal temperature, calcinated temperature and calcination time on the formation of nanostructures have been observed and characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The (BET) specific surface area of the samples which with different post treatments were determined by N₂ absorption-desorption experiment. In addition, photocatalytic activities of the nanoribbons were evaluated by photodegradation of organic dyes methyl orange under the radiation of UV light. The results reveal that the post-treatments have great effects on the microstructures and the photocatalytic activities of TiO₂ nanoribbons.