Semi‐Crystalline Polar Polyethylene: Ester‐Functionalized Linear Polyolefins Enabled by a Functional‐Group‐Tolerant,Cationic Nickel Catalyst

A dibenzobarrelene‐bridged, α‐diimine Ni^II catalyst (rac‐ 3 ) was synthesized and shown to have exceptional behavior for the polymerization of ethylene. The catalyst afforded high molecular weight polyethylenes with narrow dispersities and degrees of branching much lower than those made by related α‐diimine nickel catalysts. Catalyst rac‐ 3 demonstrated living behavior at room temperature, produced linear polyethylene (T_m=135 °C) at ?20 °C, and, most importantly, was able to copolymerize ethylene with the biorenewable polar monomer methyl 10‐undecenoate to yield highly linear ester‐functionalized polyethylene.     

Synthesis of highly branched polyethylene using para‐phenyl‐substituted α‐diimine nickel catalysts

A series of para‐phenyl‐substituted α‐diimine nickel complexes, [(2,6‐R₂‐4‐PhC₆H₂N═C(Me))₂]NiBr₂ (R = ⁱPr ( 1 ); R = Et ( 2 ); R = Me ( 3 ); R = H ( 4 )), were synthesized and characterized. These complexes with systematically varied ligand sterics were used as precatalysts for ethylene polymerization in combination with methylaluminoxane. The results indicated the possibility of catalytic activity, molecular weight and polymer microstructure control through catalyst structures and polymerization temperature. Interestingly, it is possible to tune the catalytic activities ((0.30–2.56) × 10⁶ g (mol Ni·h)^?1), polymer molecular weights (M_n = (2.1–28.6) × 10⁴ g mol^?1) and branching densities (71–143/1000 C) over a very wide range. The polyethylene branching densities decreased with increasing bulkiness of ligand and decreasing polymerization temperature. Specifically, methyl‐substituted complex 3 showed high activities and produced highly branched amorphous polyethylene (up to 143 branches per 1000 C).     

Semi‐Crystalline Polar Polyethylene: Ester‐Functionalized Linear Polyolefins Enabled by a Functional‐Group‐Tolerant,Cationic Nickel Catalyst

A dibenzobarrelene‐bridged, α‐diimine Ni^II catalyst (rac‐ 3 ) was synthesized and shown to have exceptional behavior for the polymerization of ethylene. The catalyst afforded high molecular weight polyethylenes with narrow dispersities and degrees of branching much lower than those made by related α‐diimine nickel catalysts. Catalyst rac‐ 3 demonstrated living behavior at room temperature, produced linear polyethylene (T_m=135 °C) at −20 °C, and, most importantly, was able to copolymerize ethylene with the biorenewable polar monomer methyl 10‐undecenoate to yield highly linear ester‐functionalized polyethylene.     

Ethylene polymerization with imine and phosphine nickel complexes containing isothiocyanate

Three isothiocyanate complexes of nickel(II) containing diimine [ArN?C(Me)? C(Me)?NAr]Ni‐ (NCS)₂ (1), iminophosphine [Ph₂PC₆H₄CH?NAr]Ni(NCS)₂ (2), or diphosphine (dppe)Ni(NCS)₂ (3), [Ar = 2, 6‐ⁱPr‐C₆H₃; dppe = 1, 2‐bis(diphenylphosphine)ethane] were synthesized and examined for ethylene polymerization activated by methylaluminoxane (MAO). Their behavior was compared with those of the corresponding halide analogues [ArN?C(Me)? C(Me)?NAr]NiBr₂ (4), [Ph₂PC₆H₄CH?NAr]NiBr₂ (5), and (dppe)NiCl₂ (6). The diimines showed the highest polymerization activity. Replacement of the halide for the NCS pseudo halide affected the activity and decreased the molecular weight of the polymer formed. The highest molecular weights were obtained with the diimine complexes. Highly branched polyethylenes were obtained with the bulkier complexes 1 and 4. Replacement of the halide for NCS in the diimine complexes also caused an increase in the branching content, whereas the opposite occurs for the iminophosphine complexes. The different activities and behavior of the catalyst systems with halide versus NCS in the polymerization of ethylene and the characteristics of the final products suggest a modification in the active species caused by the non‐chelating ligand. Polymer molecular weight and branching content is dependent on the MAO/Ni molar ratio and on the working temperature. Copyright © 2004 John Wiley & Sons, Ltd.     

New chiral α‐diimine nickel(II) complexes bearing ortho‐sec‐phenethyl groups for ethylene polymerization

A series of new α‐diimine nickel(II) catalysts bearing bulky chiral sec‐phenethyl groups have been synthesized and characterized. The molecular structure of representative chiral ligand, bis[N,N′‐(4‐methyl‐2,6‐di‐sec‐phenethylphenyl)imino]‐1,2‐dimethylethane rac‐1c and chiral complexes, {bis[N,N′‐(4‐methyl‐2‐sec‐phenethylphenyl)imino]‐2,3‐butadiene}dibromidonickel rac‐2a and bis{bis[N,N′‐(4‐methyl‐2‐sec‐phenethylphenyl)imino]‐2,3‐butadiene}dibromidonickel rac‐2b, were confirmed by X‐ray crystallographic analysis. Complex rac‐2c bearing two chiral sec‐phenethyl groups in the ortho‐aryl position and a methyl group in the para‐aryl position, activated by diethylaluminum chloride (DEAC), showed highly catalytic activity for the polymerization of ethylene [4.12 × 10⁶ g PE (mol Ni.h.bar)^?1], and produced highly branched polyethylenes under low ethylene pressure (branching degree: 104, 118 and 126 branches/1000 C at 20, 40 and 60°C, respectively). Chiral 20‐electron bis‐α‐diimine Ni(II) complex rac‐2b also exhibited high activity toward ethylene polymerization [1.71 × 10⁶ g PE (mol Ni · h · bar)^?1]. The type and amount of branches of the polyethylenes obtained were determined by ¹H and ¹³C NMR. Copyright © 2013 John Wiley & Sons, Ltd.     

Synthesis of branched polyethylenes by the tandem catalysis of silica‐supported linked cyclopentadienyl‐amido titanium catalysts and a homogeneous dibromo nickel catalyst having a pyridylimine ligand

The synthesis of branched polyethylenes by ethylene polymerization with new tandem catalyst systems consisting of methylaluminoxane‐preactivated linked cyclopentadienyl‐amido titanium catalysts [Ti(η⁵:η¹‐C₅Me₄SiMe₂NR)Cl₂ (R = Me or ^tBu)] supported on pyridylethylsilane‐modified silica (PySTiNMe and PySTiN^tBu) and homogeneous dibromo nickel catalyst having a pyridyl‐2,6‐diisopropylphenylimine ligand (PyminNiBr₂) in the presence of modified methylaluminoxane was investigated. Ethylene polymerization with only PyminNiBr₂ yielded a mixture of 1‐ and 2‐olefin oligomers with methyl branches [weight‐average molecular weight (M_w) ～ 460)] with a ratio of about 1:7. By the combination of this nickel catalyst with PySTiN^tBu, polyethylenes with long‐chain branches (M_w = 15,000–50,000) were produced. No incorporation of 2‐olefin oligomers was observed in the ¹³C NMR spectra. Unexpectedly, the combination of the nickel catalyst with PySTiNMe produced lower molecular weight polyethylenes with only methyl branches. The molecular weight distributions of branched polyethylenes obtained with both PySTiNMe and PySTiN^tBu combined with the nickel catalyst were broad (weight‐average molecular weight/number‐average molecular weight < 9). Bimodal gel permeation chromatography (GPC) curves were clearly observed in the PySTiNMe system, whereas GPC curves with small shoulders in low molecular weight areas were observed for PySTiN^tBu. The synthesis of branched polyethylenes with tandem catalyst systems of corresponding homogeneous titanium catalysts and the nickel catalyst was also investigated for comparison. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 528–544, 2003     

α‐Diamine Nickel Catalysts with Nonplanar Chelate Rings for Ethylene Polymerization

A series of novel α‐diamine nickel complexes, (ArNH‐C(Me)‐(Me)C‐NHAr)NiBr₂, 1 : Ar=2,6‐diisopropylphenyl, 2 : Ar=2,6‐dimethylphenyl, 3 : Ar=phenyl), have been synthesized and characterized. X‐ray crystallographic analysis showed that the coordination geometry of the α‐diamine nickel complexes is markedly different from conventional α‐diimine nickel complexes, and that the chelate ring (N‐C‐C‐N‐Ni) of the α‐diamine nickel complex is significantly distorted. The α‐diamine nickel catalysts also display different steric effects on ethylene polymerization in comparison to the α‐diimine nickel catalyst. Increasing the steric hindrance of the α‐diamine ligand by substitution of the o‐methyl groups with o‐isopropyl groups leads to decreased polymerization activity and molecular weight; however, catalyst thermal stability is significantly enhanced. Living polymerizations of ethylene can be successfully achieved using 1 /Et₂AlCl at 35 °C or 2 /Et₂AlCl at 0 °C. The bulky α‐diamine nickel catalyst 1 with isopropyl substituents can additionally be used to control the branching topology of the obtained polyethylene at the same level of branching density by tuning the reaction temperature and ethylene pressure.     

Mono‐ and binuclear nickel catalysts for 1‐hexene polymerization

Polymerization of 1‐hexene was carried out using a mononuclear (MN) catalyst and two binuclear (BN₁ and BN₂) α‐diimine Ni‐based catalysts synthesized under controlled conditions. Ethylaluminium sesquichloride (EASC) was used as an efficient activator under various polymerization conditions. The highly active BN₂ catalyst (2372 g poly(1‐hexene) (PH) mmol^?1 cat) in comparison to BN₁ (920 g PH mmol^?1 cat) and the MN catalyst (819 g PH mmol^?1 cat) resulted in the highest viscosity‐average molecular weight (M_v) of polymer. Moreover, the molecular weight distribution (MWD) of PH obtained using BN₂/EASC was slightly broader than those obtained using BN₁ and MN (2.46 for BN₂ versus 2.30 and 1.96 for BN₁ and MN, respectively). These results, along with the highest extent of chain walking for BN₂, were attributed to steric, nuclearity and electronic effects of the catalyst structures which could control the catalyst behaviour. Differential scanning calorimetry showed that the glass transition temperatures of polymers were in the range ? 58 to ?81 °C, and broad melting peaks below and above 0 °C were also observed. In addition, longer α‐olefins (1‐octene and 1‐decene) were polymerized and characterized, for which higher yield, conversion and molecular weight were observed with a narrower MWD. The polymerization parameters such as polymerization time and polymerization temperature showed a significant influence on the productivity of the catalysts and M_v of samples.     

Fluorinated α-Diimine Nickel Mediated Ethylene (Co)Polymerization

Fluorine substituents in transition metal catalysts are of great importance in olefin polymerization catalysis; however, the comprehensive effect of fluorine substituents is elusive in seminal late transition metal α-diimine catalytic system. In this contribution, fluorine substituents at various positions (ortho-, meta-, and para-F) and with different numbers (F_n; n=0, 1, 2, 3, 5) were installed into the well-defined N-terphenyl amine and thus were studied for the first time in the nickel α-diimine promoted ethylene polymerization and copolymerization with polar monomers. The position of the fluorine substituent was particularly crucial in these polymerization reactions in terms of catalytic activity, polymer molecular weight, branching density, and incorporation of polar monomer, and thus a picture on the fluorine effect was given. As a notable result, the ortho-F substituted α-diimine nickel catalyst produced highly linear polyethylenes with an extremely high molecular weight (M_w=8703 kDa) and a significantly low degree of branching of 1.4/1000 C; however, the meta-F and/or para-F substituted α-diimine nickel catalysts generated highly branched (up to 80.2/1000 C) polyethylenes with significantly low molecular weights (M_w=20-50 kDa).     

Ultrahigh Branching of Main‐Chain‐Functionalized Polyethylenes by Inverted Insertion Selectivity

Branched polyolefin microstructures resulting from so‐called “chain walking” are a fascinating feature of late transition metal catalysts; however, to date it has not been demonstrated how desirable branched polyolefin microstructures can be generated thereby. We demonstrate how highly branched polyethylenes with methyl branches (220 Me/1000 C) exclusively and very high molecular weights (ca. 10⁶ g mol^?1), reaching the branch density and microstructure of commercial ethylene–propylene elastomers, can be generated from ethylene alone. At the same time, polar groups on the main chain can be generated by in‐chain incorporation of methyl acrylate. Key to this strategy is a novel rigid environment in an α‐diimine Pd^II catalyst with a steric constraint that allows for excessive chain walking and branching, but restricts branch formation to methyl branches, hinders chain transfer to afford a living polymerization, and inverts the regioselectivity of acrylate insertion to a 1,2‐mode.     

Achieving branched polyethylene waxes by aryliminocycloocta[b]pyridylnickel precatalysts: Synthesis,characterization, and ethylene polymerization

Cycloocta[b ]pyridin‐10‐one was prepared to form the corresponding imino derivatives, which then reacted with (DME)NiBr₂ to form 10‐aryliminocycloocta[b ]pyridylnickel bromides ( Ni1 – Ni5 ). The new compounds were characterized by means of FT‐IR spectroscopy as well as elemental analysis and the organic ligands were also analyzed by the NMR measurements. Furthermore, the molecular structure of a representative complex Ni3 was determined by the single crystal X‐ray diffraction, indicating the distorted tetrahedral geometry around the nickel atom. Upon the activation with either methylaluminoxane (MAO) or diethylaluminium chloride (Et₂AlCl), the title nickel complexes exhibited high activity in ethylene polymerization and produced polyethylene of low molecular weight (1.43–6.78 kg mol^?1) and low dispersity (1.7–2.4), which suggests a single‐site catalytic system. More importantly, the microstructure of the resultant polyethylene (especially degree of branching) and certain physical properties, such as T _m values, can easily be modulated by selecting the proper substituents within the ligands and adjusting the polymerization conditions. This finding demonstrates that it is plausible to use a single catalyst for synthesizing different types of polyethylene on demand.10‐Aryliminocycloocta[b ]pyridylnickel bromides ( Ni1–Ni5 ), upon activation with either MAO or Et₂AlCl, exhibited high activity towards ethylene polymerization and produced polyethylenes with low molecular weight (1.43–6.78 kg mol^?1) and low dispersity (1.7–2.4). © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 2601–2610     

Linear/branched Block Polyethylene Produced by α-Diimine Nickel(Ⅱ)Catalyst and Bis(phenoxy-imine) Zirconium Binary Catalyst System in the Presence of Diethyl Zinc

In order to promote development of linear/branched block polyethylenes based on new catalytic systems,we synthesized a novel α-diimine nickel(Ⅱ) complex with isopropyl substituents on ortho-N-aryl and hydroxymethyl phenyl substituents on para-N-aryl structures.The activity of α-diimine nickel(Ⅱ) catalyst was 3.02×106 g·molNi-1·h-1 at 70 ℃,and resultant polyethylene possessed 135/1000C branches.The linear/branched block polyethylenes were synthesized from ethylene polymerization catalyzed by the α-diimine nickel(Ⅱ) complex/bis(phenoxy-imine) zirconium in the presence of diethyl zinc.With the addition of ZnEt2 (from 0 to 400),the melting peak of resultant polyethylene changed from a single melting peak to bimodal melting peaks.The molecular weights of resultant polyethylene ranging from 26.8 kg/mol to 17.1 kg/mol and PDI values varying gradually from 24.4 to 15.2 were obtained via adjusting ZnEt2 equiv.and molar ratio of two catalysts.In addition,the branching degree of the polyethylene increased from 13/1000C to 56/1000C with the increase of the proportion of α-diimine nickel(Ⅱ) catalyst.Using this binary catalyst system,the reaction temperature of chain shuttling polymerization can be carried out at 70 ℃,which is more conducive to industrial application.     

Synthesis of novel branched ethylene/cyclopentene copolymers with only cis‐1,3‐enchained cyclopentene units using α‐diimine nickel(II) complexes in the presence of methylaluminoxane

The copolymerization of ethylene with cyclopentene catalyzed by three α‐diimine nickel(II) complexes in the presence of methylaluminoxane (MAO) was investigated. High‐molecular‐weight branched ethylene/cyclopentene copolymers with only cis‐1,3‐enchained cyclopentene units, which has not been reported previously, were obtained. The catalytic activity, cyclopentene incorporation, copolymer molecular weight, and molecular‐weight distribution could be controlled over a wide range through the variation of the catalyst structure and polymerization conditions, including cyclopentene concentration in the feed and polymerization temperature. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2186–2192, 2008     

Activity and stability spontaneously enhanced toward ethylene polymerization by employing 2‐(1‐(2,4‐dibenzhydrylnaphthylimino)ethyl)‐6‐(1‐(arylimino)ethyl) pyridyliron(II) dichlorides

A series of 2‐(1‐(2,4‐dibenzhydrylnaphthylimino)ethyl)‐6‐(1‐(arylimino)ethyl)pyridyliron(II) complexes ( Fe1 ? Fe5 ) was synthesized and characterized. The molecular structure of the representative Fe2 was determined by single‐crystal X‐ray diffraction, revealing a distorted pseudo‐square‐pyramidal geometry around the iron center. On activation with either methylaluminoxane (MAO) or modified methylaluminoxane (MMAO), all these iron complex precatalysts performed with high activities (up to 1.58 × 10⁷ g (PE) mol^?1 (Fe) h^?1) toward ethylene polymerization, producing highly linear polyethylenes with high molecular weight and bimodal distribution, which was in accordance with high temperature ¹³C NMR, high T _m values (T _m ～130 °C) and the GPC curves of the obtained polyethylenes. Meanwhile, DFT calculation results also showed the good correlation between net charges on iron and experimental activities. Compared with previous bis(imino)pyridyliron analogues, the current iron complexes containing the benzhydrylnaphthyl groups exhibited relatively higher activities and better thermal‐stability at elevated temperatures, especially at 80 °C as the industrial operating temperature, and still showed high activities toward ethylene polymerization up to 8.57 × 10⁶ g (PE) mol^?1 (Fe) h^?1 in the presence of co‐catalyst MMAO. In addition, these iron complex precatalysts all exhibited long lifetimes. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 988–996     

Synthesis of polyethylene thermoplastic elastomer by using robust α-diimine Ni(II) catalysts with abundant tBu substituents

The synthesis of polyethylene thermoplastic elastomers via α-diimine-nickel-catalyzed ethylene polymerization using polymerization conditions of elevated temperatures and alkane solvents is highly desirable in industrial production. In this contribution, we constructed a series of highly sterically demanding α-diimine Ni(II) catalysts with abundant ^tBu substituents for this purpose. These nickel catalysts were examined for ethylene polymerization in hexanes at elevated temperatures (up to 90°C) and proved to be thermally robust at temperatures as high as 90°C. Generally, these nickel catalysts can generate highly branched (ca. 70–80/1000°C) polyethylenes with very high molecular weight (M_n up to 55.79 × 10⁴ g/mol) and the resultant polyethylenes displayed characteristics of thermoplastic elastomers with excellent elastic recovery (SR up to 84%). Compared with some similar α-diimine Ni(II) catalysts, it is shown that the presence of axial remote ^tBu substituents not only facilitates the dissolution of the catalyst in alkanes, but also improves the elastic recovery value of the obtained polyethylene.     

Alkylaluminum activator effects on polyethylene branching using a N,N′‐nickel precatalyst appended with bulky 4,4′‐dimethoxybenzhydryl groups

Ten unsymmetrical N,N'‐bis (imino) acenaphthene‐nickel (II) halide complexes, [1‐[2,6‐{(4‐MeOC₆H₄)₂CH}₂–4‐MeC₆H₂N]‐2‐(ArN)C₂C₁₀H₆]NiX₂, each appended with one N‐2,6‐bis(4,4'‐dimethoxybenzhydryl)‐4‐methylphenyl group, have been synthesized and characterized. The molecular structures of Ni1 , Ni3 , Ni5 and Ni6 highlight the variation in steric protection afforded by the inequivalent N‐aryl groups; a distorted tetrahedral geometry is conferred about each nickel center. On activation with diethylaluminum chloride (Et₂AlCl) or methylaluminoxane (MAO), all complexes showed high activity at 30°C for the polymerization of ethylene with the least bulky bromide precatalysts ( Ni1 and Ni4 ), generally the most productive, forming polyethylenes with narrow dispersities [M_w/M_n: < 3.4 (Et₂AlCl), < 4.1 (MAO)] and various levels of branching. Significantly, this level of branching can be influenced by the type of co‐catalyst employed, with Et₂AlCl having a predilection towards polymers displaying significantly higher branching contents than with MAO [T_m: 33.0–82.5°C (Et₂AlCl) vs. 117.9–119.4°C (MAO)]. On the other hand, the molecular weights of the materials obtained with each co‐catalyst were high and, in some cases, entering the ultra‐high molecular weight range [M_w range: 6.8–12.2 × 10⁵ g mol^?1 (Et₂AlCl), 7.2–10.9 × 10⁵ g mol^?1 (MAO)]. Furthermore, good tensile strength (ε_b up to 553.5%) and elastic recovery (up to 84%) have been displayed by selected more branched polymers highlighting their elastomeric properties.     

Nickel N‐heterocyclic carbene complexes in the vinyl polymerization of norbornene

Vinyl polymerized norbornene has some useful properties such as good mechanical strength, optical transparency and heat resistance. Several transition metal complexes have been described in the literature as active catalysts for the vinyl polymerization of norbornene. We now report the use of three types of nickel(II) complexes with N‐heterocyclic carbene (NHC) ligands in the catalytic vinyl polymerization of norbornene under a range of conditions. Specifically, two nickel complexes bearing a chelating bis(NHC) ligand, two nickel complexes bearing two chelating anionic N‐donor functionalized NHC ligands as well as one diiodidonickel(II) complex with two monodentate NHC ligands were tested. The solid‐state structure of bis(1,3‐dimethylimidazol‐2‐ylidene)diiodidonickel(II), as determined by X‐ray crystallography, is presented. The highest polymerization activity of 2.6 × 10⁷ g (mol cat)^?1 h^?1 was observed using the latter nickel complex as catalyst, activated by methylaluminoxane. The norbornene polymers thus obtained are of high molecular weight but with rather low polydispersity. Copyright © 2010 John Wiley & Sons, Ltd.     

Synthesis and ethylene polymerization of 8‐(fluorenylarylimino)‐5,6,7‐trihydroquinolylnickel chlorides: Tailoring polyethylenes by adjusting fluorenyl position and adduct Et2Zn

A series of 8‐(arylimino)‐5,6,7‐trihydroquinolines ligand pendant fluorenyl group at N‐aryl ring, and their nickel complexes ( Ni1 ? Ni5 ) have been prepared and characterized. Once activated with Et₂AlCl, the complexes Ni1 , Ni2 , and Ni3 bearing ligands from para‐fluorenylaniline produced unimodal polyethylenes; on the contrary complexes Ni4 and Ni5 gave bimodal polyethylenes due to steric influence of ligands from ortho‐fluorenyl anilines. With a increment of Et₂Zn/ Ni4 ratio from 0 to 400, the distinct bimodel polyethylenes were obtained with molecular weights shifted from 14.3 to 57.6 kg·mol^?1; apart shiftment to higher molecular weights, the portion of low molecular weight decreased along with higher portion of high molecular weight. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 1910–1919     

Vinyl addition polymerization of norbornene using cyclopentadienylzirconium trichloride activated by isobutyl‐modified methylaluminoxane

Norbornene polymerization using the commercially available and inexpensive catalyst system, cyclopentadienylzirconium trichloride (CpZrCl₃) and isobutyl‐modified methylaluminoxane (MMAO), were carried out over a wide range of polymerization temperatures and monomer concentrations. For the CpZrCl₃ catalyst system activated by aluminoxane with a 40 mol % methyl group and a 60 mol % isobutyl group (MMAO_40/60), the polymerization temperature and monomer concentration significantly affected the molecular weight (M_n) of the obtained polymer and the catalytic activity. With an increase in the polymerization temperature from 0 to 27 °C, the catalytic activity and M_n increased, but these values dramatically decreased with the increasing polymerization temperature from 27 to 70 °C, meaning that the most suitable temperature was 27 °C. The CpZrCl₃/MMAO_40/60 ([Al]/[Zr] = 1000) catalyst system with the [NB] of 2.76 mol L^?1 at 27 °C showed the highest activity of 145 kg mol_Zr^?1 h^?1 and molecular weight of 211,000 g mol^?1. The polymerization using the CpZrCl₃/MMAO_40/60 catalyst system proceeds through the vinyl addition mechanism to produce atactic polynorbornene, which was soluble in chloroform, toluene, and 1,2‐dichlorobenzene, but insoluble in methanol. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1185–1191, 2008     

α-萘基丁二亚胺氯化镍/MAO制备双(宽)峰聚乙烯

合成了一种新型α 二亚胺镍配合物———α 萘基丁二亚胺氯化镍 ,此配合物作为催化剂在MAO的活化下催化乙烯聚合得到支化聚乙烯 ,聚合活性高达 7 18× 10 5gPE molNi·h ,1 3C NMR、FTIR测试结果表明制备的聚乙烯含有末端双键 ;GPC结果表明所制备的聚乙烯分子量呈双 (宽 )峰分布 ,其原因有两个 ,一是此催化剂能产生分子量较低的α 烯烃 ,在聚合过程中一部分α 烯烃会“就地”与乙烯原位共聚形成分子量较高的聚合物 ,二是此催化剂存在立体异构体 ,而不同异构体在MAO活化下形成的活性中心的配位环境不同 ,因而得到的聚乙烯的分子量也不同 .研究了聚合温度、聚合压力、铝镍摩尔比 (nAl nNi)对催化活性、聚乙烯分子量、支化度的影响 .聚乙烯的分子量随聚合温度的升高而下降 ,支化度增大 ,熔点则降低 .