Two‐Phase Flow Characterization by Automated Digital Image Analysis. Part 2: Application of PDIA for Sizing Sprays

A series of experiments were conducted in order to assess the robustness and accuracy of a recently developed digital image analysis technique (PDIA). This paper investigates the application of the PDIA technique to the sizing of relatively small fuel droplets of diameters in the range 5 to 30 μm produced by a pressure‐swirl atomizer. The measurement performance of the PDIA system has been assessed in terms of individual object diameters and also number and volume probability density functions of diameter in comparison to phase Doppler anemometry (PDA) data obtained under identical conditions. PDIA measurements revealed good agreement with spray data obtained by PDA at a measurement location 36 diameters downstream from the nozzle orifice with differences in the arithmetic mean diameter, D₁₀ and volume mean diameter, D₃₀ of approximately 5 and 3% respectively. The PDIA technique was shown to detect the presence of very large, predominantly non‐spherical droplets whose diameters were in excess of 100 μm. These droplets, although few in number constitute a significant proportion of the total spray volume and would have otherwise been either erroneously measured or have passed through the probe volume undetected using PDA due to non‐sphericity. Smaller objects may also be measured correctly by both methods although sensitivity to signal‐to‐noise ratio, for both methods can generate spurious and contradictory errors.     

Mid-infrared laser-absorption diagnostic for vapor-phase measurements in an evaporating n-decane aerosol

A novel three-wavelength mid-infrared laser-based absorption/extinction diagnostic has been developed for simultaneous measurement of temperature and vapor-phase mole fraction in an evaporating hydrocarbon fuel aerosol (vapor and liquid droplets). The measurement technique was demonstrated for an n-decane aerosol with D ₅₀∼3 μ m in steady and shock-heated flows with a measurement bandwidth of 125 kHz. Laser wavelengths were selected from FTIR measurements of the C–H stretching band of vapor and liquid n-decane near 3.4 μm (3000 cm ⁻¹), and from modeled light scattering from droplets. Measurements were made for vapor mole fractions below 2.3 percent with errors less than 10 percent, and simultaneous temperature measurements over the range 300 K<T<900 K were made with errors less than 3 percent. The measurement technique is designed to provide accurate values of temperature and vapor mole fraction in evaporating polydispersed aerosols with small mean diameters (D ₅₀<10 μ m), where near-infrared laser-based scattering corrections are prone to error.     

测量单泡声致发光中气泡R(t)曲线的前向Mie散射技术

光干涉原理和Mie理论计算结果表明,单泡声致发光中气泡前向Mie散射的振荡信号,主要是由于气泡的透射光束和表面反射光束之间光干涉产生的. 这些干涉波峰形成了测量气泡半径的空间标尺,标尺的单位长度δR由散射角θ,检测光波波长和流体光折射率确定,而每个波峰就是标尺的刻线,它们与该时刻的气泡半径大小一一对应. 在30°—50°散射角范围内,利用前向Mie散射实验测定了单泡声致发光中气泡的最大半径,R(t)曲线及平衡半径,表明前向Mie散射是一种便捷的测定气泡运动特性的有效方法. 关键词： 单泡声致发光 前向Mie散射 光干涉     

Two-Color Dual-Polarization Pulsed Bistatic Lidar for Measuring Water Cloud Droplet Size

The concept of a pulsed bistatic lidar for measuring water cloud particle size is presented. The method uses a two-color laser and a receiver with a polarization analyzer located at a suitable scattering angle. The dependence of Mie scattering on scattering angle, wavelength, and polarization is used to derive water cloud droplet size. The measurement was simulated for the C₁ and C₂ clouds, and the technique for determining mode radius was studied. The result shows the lidar system with a two-wavelength laser (1064 nm and 532 nm) and a dual-polarization receiver fixed at a scattering angle of around 178 deg can be used to measure a cloud particle size (mode radius) of 4 to 12 μm. Evaluation of the effect of multiple scattering showed that the method can be applied not only for the measurement at the cloud base but also in the cloud where multiple scattering is not negligible.     

Droplet impact on regular micro-grooved surfaces

We have investigated experimentally the process of a droplet impact on a regular micro-grooved surface. The target surfaces are patterned such that micro-scale spokes radiate from the center, concentric circles, and parallel lines on the polishing copper plate, using Quasi-LIGA molding technology. The dynamic behavior of water droplets impacting on these structured surfaces is examined using a high-speed camera, including the drop impact processes, the maximum spreading diameters, and the lengths and numbers of fingers at different values of Weber number. Experimental results validate that the spreading processes are arrested on all target surfaces at low velocity. Also, the experimental results at higher impact velocity demonstrate that the spreading process is conducted on the surface parallel to the micro-grooves, but is arrested in the direction perpendicular to the micro-grooves. Besides, the lengths of fingers increase observably, even when they are ejected out as tiny droplets along the groove direction, at the same time the drop recoil velocity is reduced by micro-grooves which are parallel to the spreading direction, but not by micro-grooves which are vertical to the spreading direction.     

Estimation of the droplet size spread with the laser induced fluorescence/Mie technique

The laser measurement technique based on the ratio between the laser induced fluorescence (LIF) and the scattered light (Mie) intensities of droplets is presently limited to the evaluation of the Sauter mean diameter of the droplets. The important measurement of the droplet size spread is currently missing. An extension of the LIF/Mie technique for the measurement of droplet size spread is proposed here and is evaluated numerically. The method is based on the imperfect relationships between the scattered light intensity and the droplet surface area or the fluorescent light intensity and the droplet volume, which convey additional information that can be used to evaluate the droplet size spread.     

Evolution and impingement of an automotive fuel spray investigated with simultaneous Mie/LIF techniques

The spatial and temporal evolution of an automotive hollow-cone-type spray was investigated with laser-based imaging diagnostics. Optical conditions of an IC engine were emulated with a test cell that was built from an engine cylinder head to hold a high-pressure gasoline-fuel injector. The use of iso-octane fuel that was doped with 3-pentanone allowed measurements of laser-induced fluorescence (LIF) after excitation with a KrF excimer-laser beam. A versatile optical filter system was designed and built that permits simultaneous measurements of Mie-scattering and laser-induced-fluorescence images using a single laser-light sheet and a single intensified CCD camera. The influence of background signals, caused by reflection of signal light from surfaces, laser-sheet intensity attenuation and signal decrease by scattering, was characterized. Mass distributions showed a distinct pre-spray phase, more so than the Sauter mean diameter (SMD) that was determined from the ratio of LIF to Mie signals using single pulse as well as averaged image pairs. Significant changes in SMD distributions were found after the spray had impinged on a flat surface. The impingement also led to the buildup of a liquid film whose thickness was quantitatively determined from LIF images. Received: 5 December 2000 / Revised version: 28 February 2001 / Published online: 23 May 2001     

Simultaneous Measurement of Droplet Size and Three-Components of Velocity in Spray

The combination of the optical diagnostics and image processing technique has produced various methods of practical measurement in engineering. The measurement of size and velocity of droplets in fuel spray is one typical example. In general, the spray is a complicated and three-dimensional two-phase flow; therefore multi-dimensional field measurement of the spray field is indispensable. In the present paper, a technique of simultaneous measurement of droplet size and three-components of velocity is proposed and applied to spray issuing from the swirl nozzle as a practical application. The focused image of glare points is captured by a stereoscopic arrangement, and droplet size and the three-components of velocity are evaluated from the doublet image. Fundamental optical arrangements to capture the image of the glare points with a stereo view are established, and the feasibility and the accuracy of the technique are confirmed. © 2004 The Optical Society of Japan     

Performance Evaluation of Different Phase-Doppler Systems

The results of comparative measurements of three different phase-Doppler systems applied to a steady-state water spray are discussed. The three receiving systems, i. e. DANTEC 57X receiving optics with covariance processor, an AEROMETRICS fibre-based receiver with DSA processor and standard INVENT phase-Doppler extension, were used with a 2-D fibre-optics-based transmitting system. A constant scattering angle of 70° was chosen, which is near the Brewster angle for water. Measurements were taken in the spray cone of hollow-cone pressure atomizer at two different axial distances from the nozzle. Local size distributions, size/velocity correlations and the mean diameters D₁₀ and D₃₂ were compared. The results indicate very good agreement between the different systems, especially with respect to the mean diameters. Larger scatter of the results occurs for the measured volume flow rates, but the calculated mean volume flow rates coincide fairly well with the nominal flow rate of the atomizer.     

Effect of water–methanol content on the structure of Nafion in the sandwich model and solvent dynamics in nano-channels; a molecular dynamics study

Continuing an ongoing study, molecular dynamics (MD) simulations were performed to investigate the effects of methanol concentration on Nafion morphology, such as the size of solvent cluster, solvent location, and polymer structure via the sandwich model. Our survey shows that high methanol concentrations resulted in increment of solvent cluster size in Nafion membrane. The sulfonic acid clusters also befall much in order as subsequent layers of such ionic clusters are formed. The number of neighbouring hydronium ions around a sulfur atom is independent of methanol concentration, but the first shell of hydronium and water around sulfonic acid clusters is broader. Although methanol would prefer to interact with water molecules rather than sulfonic acid groups, gathering of methanol molecules via hydrophobic self-aggregation is preferred. Methanol is located closer to the hydrophobic part of the polymer than water, while water is located closer to the hydrophilic part of the polymer. It was found that methanol distributes specifically more than water in nano-channels. Investigation of solvent dynamics in nano-channels shows that diffusion coefficients (D) of water, methanol, and hydronium decrease with increasing methanol concentration and they may be ordered as follows: D _Water?>?D _Methanol?>?D _Hydronium (D _Water?≈?1.6–2.0D _Methanol and D _Methanol?≈?2.1–3.0D _Hydronium).     

雾滴粒子群的偏振特性研究

根据Mie散射理论,基于一次实测资料拟合得出雾滴谱分布,计算了雾滴粒子群的散射相函数矩阵,揭示了不同波长的雾滴粒子群对入射激光的散射偏振特征。结果表明：激光散射强度随散射角的增加呈现先减小后增大的趋势,且波长越小散射光强分布越集中;波长越大,偏振度随散射角分布越平滑,反之分布震动则越剧烈;各波段偏振度随散射角增大的分布趋势大致相同,关键散射角随波长的减小向增大的方向偏移。     

Effect of Mannosylerythritol lipid-A on light scattering of AOT/D<Subscript>2</Subscript>O/Octane

The light scattering technique is used for the study of interaction of Mannosylerythritol lipid-A on AOT/D₂O/Octane. The collective diffusion of AOT/D₂O droplets soluble in Octane mixed with lipid is founded from a correlation function of light scattering. We focus on the variation of the dynamic behavior of droplets as a function of the lipid concentrations and the size of droplets. The increase of concentration of Mannosylerythritol lipid-A on microemulsion decreases the dynamic of droplets. The SAXS experiment shows the size and the interaction of the droplets change by increase of Mannosylerythritol lipid-A concentration. A hard sphere model can describe the interaction of lipid with AOT/D₂O droplets.     

Rainbow Interferometry with Wire Diffraction for Simultaneous Measurement of Droplet Temperature,Size and Velocity

A rainbow measurement technique is presented which measures simultaneously the size, temperature and velocity of individual droplets in a spray. The technique is based on rainbow interferometry in combination with diffraction by a wire placed in the spatial filter of the scattered-light detector. A photomultiplier detects the wire diffraction pattern superimposed on the rainbow interference pattern created by a droplet scattering laser light. The velocity is determined from the equivalent geometric wire shadow. The necessary sphericity validation is performed by comparing the Airy and the ripple droplet diameters, resulting from the respective interference structures. The temperature is recovered from the position of the wire diffraction pattern relative to the main rainbow maximum. The technique was applied to a water spray at ambient temperature. The results showed the importance of nonsphericity detection.     

Digital Holography for Instantaneous Spray Diagnostics on a Plane

We present a measurement technique that is capable of simultaneously determining sizes and positions of multiple transparent droplets in a plane from scattered light features. The technique is largely independent of particle intensity and mutual obscuration. Reflected and refracted light from the droplets in a pulsed laser sheet is recorded holographically to yield the smallest possible probe volume and the largest possible number density. Larger droplets are best analyzed at the image plane; in this case, the droplets appear as two spots (glare points), whose separation is proportional to the droplet diameter. Smaller droplets are easier to analyze at an out‐of‐focus plane, where their images appear as fringe patterns whose spatial frequency is related to droplet size. Photographic techniques allow only one of these planes to be chosen and are therefore not suitable for multidisperse sprays. Optical holography allows to analyze arbitrary depths, but often suffers from low sensitivity and long analysis times. With digital holography, the spray images are captured digitally by a CCD camera and reconstructed numerically; as in optical holography, the particle reconstruction plane can be freely chosen a posteriori to optimize the measurement. We discuss the issues raised by the transition from holographic film to a CCD sensor as the recording medium, and demonstrate the capabilities of the digital technique.     

Critical dynamics and multifractal exponents at the Anderson transition in 3d disordered systems

We investigate the dynamics of electrons in the vicinity of the Anderson transition in d = 3 dimensions. Using the exact eigenstates from a numerical diagonalization, a number of quantities related to the critical behavior of the diffusion function are obtained. The relation η = d ? D₂ between the correlation dimension D₂ of the multifractal eigenstates and the exponent η which enters into correlation functions is verified. Numerically, we have η ≈? 1.3. Implications of critical dynamics for experiments are predicted. We investigate the long-time behavior of the motion of a wave packet. Furthermore, electron-electron and electron-phonon scattering rates are calculated. For the latter, we predict a change of the temperature dependence for low T due to η. The electron-electron scattering rate is found to be linear in T and depends on the dimensionless conductance at the critical point.     

Evaluation method for radiative heat transfer in polydisperse water droplets

Simplifications of the model for nongray radiative heat transfer analysis in participating media comprised of polydisperse water droplets are presented. Databases of the radiative properties for a water droplet over a wide range of wavelengths and diameters are constructed using rigorous Mie theory. The accuracy of the radiative properties obtained from the database interpolation is validated by comparing them with those obtained from the Mie calculations. The radiative properties of polydisperse water droplets are compared with those of monodisperse water droplets with equivalent mean diameters. Nongray radiative heat transfer in the anisotropic scattering fog layer, including direct and diffuse solar irradiations and infrared sky flux, is analyzed using REM². The radiative heat fluxes within the fog layer containing polydisperse water droplets are compared with those in the layer containing monodisperse water droplets. Through numerical simulation of the radiative heat transfer, polydisperse water droplets can be approximated by using the Sauter diameter, a technique that can be useful in several research fields, such as engineering and atmospheric science. Although this approximation is valid in the case of pure radiative transfer problems, the Sauter diameter is reconfirmed to be the appropriate diameter for approximating problems in radiative heat transfer, although volume-length mean diameter shows better accordance in some cases. The CPU time for nongray radiative heat transfer analysis with a fog model is evaluated. It is proved that the CPU time is decreased by using the databases and the approximation method for polydisperse particulate media.     

Lidar Network System for Monitoring the Atmospheric Environment in Jakarta City

A lidar network system consisting of two Mie scattering lidars and one differential absorption lidar was developed to measure the atmospheric environment in Jakarta. The three lidars were installed at three locations in Jakarta to study atmospheric boundary layer structure and transportation of atmospheric pollutants. The Mie scattering lidars employ compact flashlamp pumped Nd:YAG lasers operated at 1064 nm fundamental. They are installed in shelters and directed vertically. One of the Mie lidar has a rotating wedged window for scanning conically to measure wind velocity using a correlation method. The DIAL system employs two Nd:YAG laser-pumped optical parametric oscillators. The DIAL is designed to measure distribution of ozone and SO₂ in the near UV region, and NO₂ in the 450-nm region. The system is installed in a shelter and has a full scanning capability.     

Imaging of the oxygen distribution in an isothermal turbulent free jet using two-color toluene LIF imaging

The results of a novel technique for the quantification of oxygen in an isothermal turbulent free jet using toluene laser induced fluorescence (LIF) are presented. This method relies on the red-shift of the toluene LIF emission spectrum with increasing oxygen concentration. Evaluating the LIF signal ratio from two different wavelength regions simultaneously produces results that depend only on the local oxygen concentration. From calibration data, obtained from repeated tests, the oxygen sensitivity of the two-color LIF technique is best for oxygen partial pressures p_O2 ￡ 120 mbarp_{\mathrm{O}_{2}} \leq 120\mbox{ mbar} in the current setup. Quantified images of oxygen distribution are presented for 40.4, 60.5, 80.5, and 103 mbar p_O2p_{\mathrm{O}_{2}} in the toluene-seeded jet flow that is shielded by a toluene-seeded nitrogen co-flow at atmospheric pressure and temperature. Based on the average oxygen concentration images (obtained from 100 instantaneous oxygen images), the error in accuracy of measuring the oxygen concentration was 0.8, 3.0, 7.7, and 7.3% with a precision of ± 8.6, 5.5, 13.3, and 11.6% for the jet p_O2 = 40.4, 60.5, 80.5, and 103 mbarp_{\mathrm{O}_{2}} = 40.4,\, 60.5,\, 80.5,\mbox{ and }103\mbox{ mbar} cases, respectively. The main jet flow characteristics have been captured by the technique as determined from the measured oxygen distribution images. Centerline profiles of average oxygen concentration, normalized to the value at the nozzle exit, demonstrate self-similar behavior from 5 mm above the nozzle exit. Radial oxygen concentration profiles exhibit a Gaussian-type distribution that broadens with distance above the nozzle exit, in agreement with literature.     

纳米氦液滴-超低温化学研究装置

成功研制了新一代纳米氦液滴实验装置．氦液滴是由高压的高纯氦气通过超低温的脉冲阀绝热膨胀形成的,通过调节连接在超低温氦冷头上的脉冲阀的温度(10～30 K)及脉冲阀内氦气的背景压力(10～40 atm),氦液滴的大小在包含103到105个氦原子间连续可调,和传统的连续氦液滴束源比较起来,脉冲束源的强度提高了一个量级以上,提供了一个和商品化脉冲激光器结合使用,研究超低温条件下超流体氦中的化学反应动力学的机会．通过研究氦液滴中包裹的CH₃I分子的光解动力学来对仪器的性能进行测试,利用离子速度影像技术研究了超低温纳米氦液滴中包裹的CH₃I分子在252 nm下的光解动力学,光解产物甲基通过(2+1)共振增强多光子电离并运用离子影像进行检测,结果表明光解产物的平动能及角分布被氦原子环境有效的弛豫．也证实了运用脉冲氦液滴束源研究衰减光谱的可行性,通过对氦液滴中掺杂苯的衰减光谱的研究,还发现小于3%的衰减信号都可以被检测到,表明所研制的脉冲氦液滴束的稳定性及检测器的灵敏度都是很高的．     

Measurement of mean size and evaluation of polydispersity of gold nanoparticles from spectra of optical absorption and scattering

Two methods for determination of the mean size of gold nanoparticles, based on measurement of the wavelengths of the maxima λ_max of side scattering and extinction in the range 400–700 nm, are compared. Four sols with mean particle diameters d of about 15, 20, 25, and 30 nm, measured using the dynamic light-scattering technique, were studied experimentally. The slope of the size dependence λ_max(d) of the spectral position of the scattering peak exceeded that for the extinction peak by a factor of 2.4. This fact ensures a substantially higher accuracy of the scattering method. For simulating polydispersity, mixtures of three colloids with particle diameters of 20, 25, and 30 nm were used: sample S1, with a size distribution close to the normal one of around 25 nm, and sample S2, with equal concentrations of each of the components. The extinction spectra of mixtures S1 and S2 and the initial 25-nm sol (S0) were virtually identical, whereas their scattering spectra showed a pronounced increase in the peak amplitude in the series S0, S1, S2. These results agree with calculations based on the Mie theory. Thus, scattering spectra offer advantages over extinction spectra not only in measuring the mean size of gold particles but also in evaluating their polydispersity.