Synthesis and optical and electroluminescent properties of novel conjugated polyelectrolytes and their neutral precursors derived from fluorene and benzoselenadiazole

Novel copolymers derived from amino‐functionalized fluorene‐ and selenium‐containing heterocycles [2,1,3‐benzoselenadiazole (BSeD)] were synthesized by the palladium‐catalyzed Suzuki coupling method. Their quaternized salt polyelectrolytes of corresponding compositions were obtained by a postpolymerization treatment. The resulting copolymers were soluble in polar solvents. An efficient energy transfer due to exciton trapping on the BSeD sites was observed. Devices from such copolymers emitted orange‐red light peaked at 560–610 nm. All the polymers showed good device performance with high‐work‐function metal Al as a cathode without the use of an additional electron‐injection layer and are promising candidates for polymer light‐emitting diode applications. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2521–2532, 2006     

High‐efficiency doped polymeric organic light‐emitting diodes

Fabrication of polymer light‐emitting diodes based on emission from the phosphorescent molecule fac‐tris(2‐phenylpyridine) iridium doped into a poly(N‐vinyl carbazole) host are reported. For single‐layered devices with magnesium‐silver cathodes, the luminance efficiency at 20 mA/cm² was measured as 8.7 cd/A. This efficiency could be increased by over a factor of two by incorporation of evaporated small‐molecule layers into the device structure. Significant increases in device efficiency were also obtained without these evaporated layers by modification of the electrodes. Incorporation of 3,4‐poly(ethylene dioxythiophene):poly(styrene sulfonate) at the anode improved the device efficiency but had little impact on drive voltage. Insertion of lithium fluoride at the cathode resulted in no improvement in performance for magnesium‐silver and aluminum cathodes, but a significant improvement was realized in efficiency and drive voltage for calcium‐aluminum cathodes. Excellent device performance was observed for all three cathode metals used in conjunction with cesium fluoride. Through optimization of the electrodes and emitter‐layer thickness, devices exhibiting efficiencies as high as 37.3 cd/A are realized. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2715–2725, 2003     

Surface modification of magnetic metal nanoparticles and its influence on the performance of polymer composites

To control the interfacial interaction in magnetic metal nanoparticles‐filled polymer composites, surfaces of iron, cobalt, and nickel nanoparticles were grafted by irradiation‐induced polymerization. On the basis of the study of dynamical mechanical behavior, thermal stability, and magnetic performance of the composites prepared by either solution mixing or in situ polymerization, the structure–property relationships of the composites are a function of interfacial interaction and the dispersion state of the nanoparticles. In addition, grafting of polymers onto the surface of the metal nanoparticles changed the surface magnetic state, leading to the possibility of purposely tailoring the magnetic behavior of the composites. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1070–1084, 2003     

Effect of annealing on the electrical properties and morphology of a conducting polymer used as an anode in organic light‐emitting devices

The surface sheet resistance of conducting films of glycerol‐doped poly(3,4‐ethylenedioxy‐thiophene)–poly(styrene sulfonate) is largely dependent on the annealing temperature. The presence of free glycerol in insufficiently baked films, as indicated by infrared spectra and thermogravimetric analysis, results in conducting polymer films with poor morphology and low electrical conductivity. The device performance of organic light‐emitting diodes using this modified poly(3,4‐ethylenedioxy‐thiophene)–poly(styrene sulfonate) as an anode is also greatly affected by the baking conditions of the conducting films. The maximum light output, current density, and luminous power efficiency are observed from devices using anodes baked at a high temperature close to the boiling point of glycerol. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2522–2528, 2003     

Investigation of the micromechanical deformation behavior of styrene–butadiene star block copolymer/polystyrene blends with high‐voltage electron microscopy

The deformation behavior of blends consisting of a styrene–butadiene star block copolymer and a polystyrene homopolymer was studied by high‐voltage electron microscopy with a tensile device. The mechanical properties and micromechanical deformation mechanisms in the star block copolymer/polystyrene blends were directly influenced by their morphology. Although the pure block copolymer deformed in a very unequal manner (because of a thin‐layer‐yielding mechanism) and revealed no local deformation zones, a transition to the formation of crazelike zones was observed in the blends. This transition in the deformation mechanisms was correlated to the abrupt change in the macroscopic strain at break of the injection‐molded specimens. At lower contents of added polystyrene, a craze‐stopping mechanism was observed, whereas the blends with higher polystyrene contents demonstrated crazing like that in pure polystyrene. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1157–1167, 2003     

Carbazole end‐capped pyrene starburst with enhanced electrochemical stability and device performance

Carbazole end‐capped starburst molecule based on pyrene core “4CzFP” was synthesized and characterized. The starburst material shows good film‐forming ability and bright blue fluorescence. In cyclic voltammetry test, 4CzFP shows a high highest occupied molecular orbital energy level of ?5.26 eV, indicating it has good hole‐injection ability. The material is quite stable under series of cyclic voltammetry scans, implying its good electrochemical stability. Single‐layered electroluminescent device takes on stable blue emission with a peak current efficiency of 0.84 cd/A. Double‐layered device by adding Poly(N‐vinylcarbazole) (PVK) as a hole‐injection layer does not show any improvement, indicating that 4CzFP could be efficiently used as the hole‐injection/light‐emitting layer. The device performance is largely improved by adding a thin TPBI electron‐injection/transporting layer. The peak efficiency reaches 3.28 cd/A and the maximum brightness is over 2200 cd/m². © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Dielectric properties of self‐catalytic interpenetrating polymer network based on modified bismaleimide and cyanate ester resins

Bismaleimide (BMI) resins with good thermal stability, fire resistance, low water absorption, and good retention of mechanical properties at elevated temperatures, especially in hot/wet environments, have attracted more attention in the electronic and aerospace industries. However, their relatively high dielectric constant limits their application in the aforementioned fields. In this work, a new promising approach is presented that consists of the formation of a self‐catalytic thermoset/thermoset interpenetrating polymer network. Interpenetrating polymer networks (IPNs) based on modified BMI resin (BMI/DBA) and cyanate ester (b10) were synthesized via prepolymerization followed by thermal curing. The self‐catalytic curing mechanism of BMI/DBA‐CE IPN resin systems was examined by differential scanning calorimetry. The dielectric properties of the cured BMI/DBA‐CE IPN resin systems were evaluated by a dielectric analyzer and shown in dielectric properties‐temperature‐log frequency three‐dimensional plots. The effect of temperature and frequency on the dielectric constant of the cured BMI/DBA‐CE IPN resin systems is discussed. The composition effect on the dielectric constant of the cured IPN resin systems was analyzed on the basis of Maxwell's equation and rule of mixture. The obtained BMI/DBA‐CE IPN resin systems have the combined advantages of low dielectric constant and loss, high‐temperature resistance, and good processability, which have many applications in the microelectronic and aerospace industries. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1123–1134, 2003     

Influence of crosslinking on charge carrier mobility in crosslinkable polyfluorene derivatives

Carrier mobility is a key parameter for the application of conjugated polymers. In this work, a series of polyfluorenes (PF2/6) with different fractions of crosslinkable acrylate groups is investigated. Mobility measurements are carried out to assess the influence of crosslinking with different photoinitiators on the performance of the material. For the regime of low to medium charge carrier density, relevant for OLEDs and OPVs, we used a novel technique based on the injection of charge carriers from the electrodes of an optoelectronic device: MIS‐CELIV (MIS: metal‐insulator‐semiconductor). For large charge carrier densities we performed OFET measurements. We find that using optimized conditions crosslinking does not influence the hole mobility in the investigated system. Furthermore, we demonstrate that the crosslinking process may be triggered solely by thermal activation and UV‐illumination without the need of any initiator. Thus, densely crosslinked networks are obtained without the formation of undesired decomposition products from added photoinitiator. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 112–120     

Segmental‐ and normal‐mode dielectric relaxation of poly(propylene glycol) under pressure

Dielectric measurements were obtained on poly(propylene glycol) (molecular weight: 4000 Da) at pressures in excess of 1.2 GPa. The segmental (α process) and normal‐mode (α′ process) relaxations exhibited different pressure sensitivities of their relaxation strengths, as well as their relaxation times. Such results are contrary to previous reports, and (at least for the dielectric strength) can be ascribed to the capacity for intermolecular hydrogen‐bond formation in this material. With equation‐of‐state measurements, the relative contributions of volume and thermal energy to the α‐relaxation times were quantified. Similar to other H‐bonded liquids, temperature is the more dominant control variable, although the effect of volume is not negligible. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3047–3052, 2003     

Terpyridine‐modified poly(vinyl chloride): Possibilities for supramolecular grafting and crosslinking

Commercially available poly(vinyl chloride) (PVC) was covalently modified with terpyridine supramolecular binding units in a two‐step reaction. First, PVC was modified with aromatic thiols to introduce OH functionalities into the polymer backbone, which were subsequently reacted with an isocyanate‐functionalized terpyridine binding unit. The resulting functionalized material contained metal‐ion binding sites, which could be used for grafting and crosslinking reactions. A grafting experiment was performed with a small organic terpyridine ligand. The complexation of the modified PVC with several transition‐metal ions was studied with ultraviolet–visible spectroscopy and gel permeation chromatography. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2964–2973, 2003     

Crosslinkable high dielectric constant polymer dielectrics for low voltage organic field‐effect transistor memory devices

I n this study, we successfully synthesized water/methanol soluble random copolymers with a high dielectric constant, poly(n‐(hydroxymethyl) acrylamide‐co‐5‐(9‐(5‐(diethylamino)pentyl)?2‐(4‐vinylphenyl)?9H‐fluorene(P(NMA‐co‐F6NSt)), which contained chemical crosslinkable segment (NMA) and hole trapping building block (F6NSt). The feeding molar ratios of two monomers (NMA:F6NSt) were set as 100:0, 95:5, 80:20, and 67:33 for the copolymers of P1 , P2 , P3, and P4 , respectively. The crosslinked P(NMA‐co‐F6NSt) thin film could serve as both dielectric and charge storage layers in organic field‐effect transistor (OFET) memory device and exhibited high k (i.e., 4.91–6.47) characteristics, leading to a low voltage operation and a small power consumption. Devices based on the P1 ‐ P4 dielectrics showed excellent insulating properties and good charge storage performance under a low operating voltage in a range of ±5V because of tightly network structures and well‐dispersed trapping cites. In particular, P3 ‐based memory device exhibited a large memory window of 4.13 V with stable data retention stability over 10⁴ s, a large on/off ratio of 10⁴, and good endurance characteristics as high as 200 cycles. The above results suggested that a high‐performance OFET memory device could be facilely achieved using the novel crosslinkable high‐k copolymers. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3224–3236     

Conductance and capacitance–frequency characteristics of polypyrrole/p‐type silicon structures

We formed a polypyrrole/p‐type silicon device by an anodization process. An aluminum electrode was used as an ohmic contact. From the current–voltage characteristics of the device, barrier height and ideality factor values of 0.662 eV and 1.734, respectively, were obtained from a forward‐bias current–voltage plot. Low capacitance–frequency and conductance–frequency measurements from 0.00 to 0.30 V with steps of 0.02 V were made. At each frequency, the measured capacitance decreased with increasing frequency because of a continuous distribution of the interface states in the frequency range of 5.0 Hz to 2.0 MHz. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1334–1338, 2003     

Energy transfer and triplet exciton confinement in polymeric electrophosphorescent devices

Energy transfer and triplet exciton confinement in polymer/phosphorescent dopant systems have been investigated. Various combinations of host‐guest systems have been studied, consisting of two host polymers, poly(vinylcarbazole) (PVK) and poly[9,9‐bis(octyl)‐fluorene‐2,7‐diyl] (PF), blended with five different phosphorescent iridium complexes with different triplet energy levels. These combinations of hosts and dopants provide an ideal situation for studying the movement of triplet excitons between the host polymers and dopants. The excitons either can be confined at the dopant sites or can flow to the host polymers, subject to the relative position of the triplet energy levels of the material. For PF, because of its low triplet energy level, the exciton can flow back from the dopants to PF when the dopant has a higher triplet energy and subsequently quench the device efficiency. In contrast, efficient electrophosphorescence has been observed in doped PVK films because of the high triplet energy level of PVK. Better energy transfer from PVK to the dopants, as well as triplet exciton confinement on the dopants, leads to higher device performance than found in PF devices. Efficiencies as high as 16, 8.0, and 2.6 cd/A for green, yellow, and red emissions, respectively, can be achieved when PVK is selected as the host polymer. The results in this study show that the energy transfer and triplet exciton confinement have a pronounced influence on the device performance. In addition, this study also provides material design and selection rules for the efficient phosphorescent polymer light‐emitting diodes. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2681–2690, 2003     

Playing LEGO with macromolecules: Design,synthesis, and self‐organization with metal complexes

Several synthetic strategies for the incorporation of supramolecular binding units into polymers are described. Specifically, terpyridine ligands have been introduced into polymers in such a way that they are distributed either randomly throughout the polymer backbone or at the chain end(s). Two terpyridine ligands form octahedral complexes with a variety of transition‐metal ions, each having different properties. Some general statements regarding metal complex stability are presented as well as a special case representing the selective construction of heteroleptic terpyridine complexes. This leads to a kind of LEGO system for connecting and disconnecting the polymer blocks via metal complexes. Metallo‐supramolecular block copolymers, graft copolymers, and chain‐extended polymers can be designed and prepared with the principles described. Once the design parameters have been derived, thorough control over the final material and its properties can be gained. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1413–1427, 2003     

Method of determining the absolute molecular weight from gel permeation chromatograms for star‐shaped styrenic block copolymers

A gel permeation chromatography (GPC) calculation method has been developed to determine the absolute molecular weight of a star‐shaped styrenic block copolymer with GPC–ultraviolet/refractive index calibrated with linear polystyrene standards. To illustrate the simplicity of this method, we have synthesized nearly monodisperse, multiple‐arm model polymers either by linking living polymeric arms with multifunctional silicon halide or by oligomerizing the p‐chloromethylstyrene‐terminated polystyrene macromonomers. The good agreement between the absolute molecular weight determined with this calculation method and that actually measured with a multi‐angle laser light scattering device has corroborated the validity of the calculation method. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 976–983, 2003     

Contact optimization in polymer light‐emitting diodes

To fully exploit the properties of light‐emitting polymers (LEPs) in electroluminescent applications, it is of paramount importance to develop efficient electrical contacts. An ideal electrode is highly conductive, stable, provides a low barrier to carrier injection, and does not degrade the LEP upon contact. It is difficult to find a single homogeneous material that satisfies all of these requirements. Hence, contact optimization has often required the development of multilayer structures. In particular, indium tin oxide covered by a film of poly(ethylene‐dioxythiophene):poly(styrene sulfonic acid) {ITO/PEDOT:PSS} has become a favorite combination for the transparent anode, and heterostructures of LiF and CsF with metals (Al and Ca) have proven to be efficient electron‐injecting contacts. Here we review our progress in the understanding of the operation of light‐emitting diodes incorporating such contacts, in particular by gauging the materials' energy‐level lineup via electroabsorption measurements. Among the series of LEDs investigated, using a high‐energy‐gap blue polyfuorene polymer, CsF/Ca/Al and LiF/Ca/Al electrodes lead to the best improvements in electron injection. The most promising performance for applications, where a high luminance (～1600 cd/m² at 5 V) is also accompanied by a high maximum efficiency (～3 lm/W), was obtained with LiF/Ca/Al cathodes and ITO/PEDOT:PSS anodes. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2649–2664, 2003     

Charge transport,injection, and photovoltaic phenomena in oligo(phenylenevinylene) based diodes

We report on the charge transport and injection phenomena of (E,E,E,E)‐1,4‐bis[(4‐styryl)styryl]‐2‐methoxy‐5‐(2′‐ethylhexoxy)benzene (MEH‐OPV5) sandwiched between asymmetric contacts. The hole mobility of MEH‐OPV5 was determined by means of transient electroluminescence. The steady‐state current was injection‐limited. The electric field and temperature dependence of the current were quantitatively described by a phenomenological injection model of thermally assisted charge‐carrier tunneling in a one‐dimensional chain of hopping sites. Furthermore, we report on the photovoltaic properties of thin‐film photovoltaic cells on the basis of donor–acceptor heterojunctions. MEH‐OPV5 and buckminster fullerene were used as the donor and acceptor materials, respectively. The emphasis was on the role of morphology in such devices. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2665–2673, 2003     

Successive stepwise evolution of host layer‐stacking framework upon the intercalation of mobile vapor guests within side‐chain layers

For the ordered phases of hairy‐rod semiconductive poly(2,5‐bis(3‐tetradecylthiophene‐2‐yl)thieno[3,2‐b]thiophene) (PBTTT) sandwiched in between crystalline platelets of hexamethylbenzene, the successive stepwise evolution of layer‐stacking framework upon guest intercalation has been studied in this research. The direct consequence of the guest intercalation into side‐chain layers is evaluated to cause the lateral shift of thiophene backbones along π–π stacking, resulting in stepwise shift of ultraviolet absorption wavelength. The thermal motions of vapor guests within disordering side‐chain layers subsequently cause progressive expansion of host stacking framework. With the increase in side‐chain length, thicker layers of disordering side chains in liquid crystals (LCs) accommodate additional vapor guests and larger amplitudes of thermal motions of guests, hence promoting the level of reversible d‐spacing change. The mixing between mobile vapor guests and aliphatic side chains is clarified as the mechanism of guest intercalation, which rationalizes successive guest intercalation during heating and the contribution of disordering side‐chain layers. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1448–1456     

Characteristics of a single‐layered organic electroluminescent device using a carrier‐transporting copolymer and a nonconjugated light‐emitting polymer

We have synthesized a novel carrier‐transporting copolymer and a nonconjugated light‐emitting polymer. The carrier‐transporting copolymer has a triphenylamine moiety as a hole‐transporting unit and a triazine moiety as an electron‐transporting unit, both of which are located in the polymer side chain. The nonconjugated light‐emitting polymer has a perylene moiety, which acts as an emitting unit in the polymer side chain. These polymers are very soluble in most organic solvents, such as monochlorobenzene, tetrahydrofuran, chloroform, and benzene. A single‐layered electroluminescent device consisting of ITO/copolymer and emitting‐material 4‐(dicyanomethylene)‐2‐methyl‐6‐(4‐dimethylaminostyryl)‐4H‐pyran (DCM) or light‐emitting polymer)/Al mixtures exhibits maximum external quantum efficiency when the concentration of the emitting material is 30 wt %. The device emits red or blue light according to the emitting material. When CsF is used as the electron‐injecting material, the drive voltage decreases drastically to 7 V, and the highest quantum efficiency is 0.5%. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2733–2743, 2003     

Complexation of copper(II) ions with imidazole–carboxylic polymeric systems

The interaction of two polyampholyte systems, poly(1‐vinylimidazole‐co‐acrylic acid) and interpolymer complex poly(acrylic acid)/poly(1‐vinylimidazole) with copper(II) ions in water, was examined with potentiometry (pH‐metry and Cu‐selective electrode) and electron spin‐resonance spectroscopy. Coordination of Cu²⁺ with copolymer proceeded by carboxylic groups, whereas the interpolymer system azole units were also involved in the inner sphere of the complex. Synergism between coordination with metal ions and intramolecular hydrogen or ionic bonds was shown. The interpolymer complex was an effective system for binding, extracting, and concentrating copper ions from water. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2256–2263, 2003