Inverted polymer solar cells with a solution-processed zinc oxide thin film as an electron collection layer

A solution-processed zinc oxide (ZnO) thin film as an electron collection layer for polymer solar cells (PSCs) with an inverted device structure was investigated. Power conversion efficiencies (PCEs) of PSCs made with a blend of poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl C61-butyric acid methyl ester (PCBM) are 3.50% and 1.21% for PSCs with and without the ZnO thin film, respectively. Light intensity dependence of the photocurrent and the capacitance-voltage measurement demonstrate that the increased PCEs are due to the restriction of the strong bimolecular recombination in the interface when a thin ZnO layer is inserted between the polymer active layer and the ITO electrode. These results demonstrate that the ZnO thin film plays an important role in the performance of PSCs with an inverted device structure.     

Effect of multiple adduct fullerenes on charge generation and transport in photovoltaic blends with poly(3‐hexylthiophene‐2,5‐diyl)

The effect of replacing [6,6]‐phenyl‐C₆₁ butyric acid methyl ester (PCBM) by its multiadduct analogs (bis‐PCBM and tris‐PCBM) in bulk heterojunction organic solar cells with poly(3‐hexylthiophene‐2,5‐diyl) (P3HT) is studied in terms of blend film microstructure, photophysics, electron transport properties, and device performance. Although the power conversion efficiency of the blend with bis‐PCBM is similar to the blend with PCBM, the performance of the devices with tris‐PCBM is considerably lower as a result of small photocurrent. Despite the lower electron affinity of the fullerene multiadducts, μs‐ms transient absorption measurements show that the charge generation efficiency is similar for all three fullerenes. The annealed blend films with multiadducts show a lower degree of fullerene aggregation and lower P3HT crystallinity than the annealed blend films with PCBM. We conclude that the reduction in performance is due largely to poorer electron transport in the blend films from higher adducts, due to the poorer fullerene network formation as well as the slower electron transport within the fullerene phase, confirmed here by field effect transistor measurements. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Effects of amorphous poly(3‐hexylthiophene) on active‐layer structure and solar cells performance

A key challenge to the development of polymer‐based organic solar cells is the issue of long‐term stability, which is mainly caused by the unstable time‐dependent morphology of active layers. In this study, poly(3‐hexylthiophene) (P3HT)/[6,6]‐phenyl C60‐butyric acid methyl ester (PCBM) blend is used as a model system to demonstrate that the long‐term stability of power conversion efficiency can be significantly improved by the addition of a small amount of amorphous regiorandom P3HT into semicrystalline regioregular one. The optical properties measured by UV–vis absorption and photoluminescence reveal that regiorandom P3HT can intimately mix with PCBM and prevent the segregation of PCBM. In addition, X‐ray scattering techniques were adopted to evidence the retardation of phase separation between P3HT and PCBM when regiorandom P3HT is added, which is further confirmed by optical microscopy that shows a reduction of large PCBM crystals after annealing at high temperature in the presence of regiorandom P3HT. The improvement of the long‐term stability is attributed to the capability of amorphous P3HT to be thermodynamically miscible with PCBM, which allows the active layer to form a more stable structure that evolves slower and hence decelerates the device decay. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 975–985     

Synthesis of all‐conjugated poly(3‐hexylthiophene)‐block‐ poly(3‐(4′‐(3″,7″‐dimethyloctyloxy)‐3′‐pyridinyl)thiophene) and its blend for photovoltaic applications

New all‐conjugated block copolythiophene, poly(3‐hexylthiophene)‐block‐poly(3‐(4′‐(3″,7″‐dimethyloctyloxy)‐3′‐pyridinyl)thiophene) (P3HT‐b‐P3PyT) was successfully prepared by Grignard metathesis polymerization. The supramolecular interaction between [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) and P3PyT was proposed to control the aggregated size of PCBM and long‐term thermal stability of the photovoltaic cell, as evidenced by differential scanning calorimetry (DSC), transmission electron microscopy (TEM), and optical microscopy. The effect of different solvents on the electronic and optoelectronic properties was studied, including chloroform (CL), dichlorobenzene (DCB), and mixed solvent of CL/DCB. The optimized bulk heterojunction solar cell devices using the P3HT‐b‐P3PyT/PCBM blend showed a power conversion efficiency of 2.12%, comparable to that of P3HT/PCBM device despite the fact that former had a lower crystallinity or absorption coefficient. Furthermore, P3HT‐b‐P3PyT could be also used as a surfactant to enhance the long‐term thermal stability of P3HT/PCBM‐based solar cells by limiting the aggregated size of PCBM. This study represents a new supramolecular approach to design all‐conjugated block copolymers for high‐performance photovoltaic devices. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

喷涂法制备大面积倒置聚合物光伏器件

采用喷涂工艺制备了结构为ITO/ZnO/P3HT∶PCBM/V2O5/Ag(P3HT:聚噻吩;PCBM:6,6-苯基-C61-丁酸甲酯)的大面积倒置光伏器件,有效面积为1.0×1.1 cm2。 光谱测试结果表明,退火处理后,P3HT∶PCBM薄膜吸收显著增强,并且产生一定程度的红移。 采用ZnO和V2O5代替LiF和PEDOT∶PSS(聚(3,4-乙撑二氧噻吩)∶聚苯乙烯磺酸盐)作为器件修饰层,避免了PEDOT∶PSS对ITO的腐蚀和LiF潮解,采用Ag代替Al作为金属背电极避免了Al被氧化。 经过后退火处理器件的效率从1.1%提升至1.65%。 器件的稳定性相对于传统结构有了大幅提升,8周后器件效率只衰减10%。     

Quantitative nanoorganized structural evolution for a high efficiency bulk heterojunction polymer solar cell

We have developed an improved small-angle X-ray scattering (SAXS) model and analysis methodology to quantitatively evaluate the nanostructures of a blend system. This method has been applied to resolve the various structures of self-organized poly(3-hexylthiophene)/C61-butyric acid methyl ester (P3HT/PCBM) thin active layer in a solar cell from the studies of both grazing-incidence small-angle X-ray scattering (GISAXS) and grazing-incidence X-ray diffraction (GIXRD). Tuning the various length scales of PCBM-related structures by a different annealing process can provide a flexible approach and better understanding to enhance the power conversion of the P3HT/PCBM solar cell. The quantitative structural characterization by this method includes (1) the mean size, volume fraction, and size distribution of aggregated PCBM clusters, (2) the specific interface area between PCBM and P3HT, (3) the local cluster agglomeration, and (4) the correlation length of the PCBM molecular network within the P3HT phase. The above terms are correlated well with the device performance. The various structural evolutions and transformations (growth and dissolution) between PCBM and P3HT with the variation of annealing history are demonstrated here. This work established a useful SAXS approach to present insight into the modeling of the morphology of P3HT/PCBM film. In situ GISAXS measurements were also conducted to provide informative details of thermal behavior and temporal evolution of PCBM-related structures during phase separation. The results of this investigation significantly extend the current knowledge of the relationship of bulk heterojunction morphology to device performance.     

电沉积ZnO纳米棒阵列及共形结构杂化太阳能电池

采用电沉积法制备出ZnO致密纳米颗粒膜和不同尺寸的纳米棒阵列。通过在ZnO上旋涂p型聚合物聚3-己基噻酚(P3HT)与n型富勒烯衍生物[6,6]-苯基-C61丁酸甲酯(PCBM)的混合物,并蒸镀金属Ag,制备出不同结构的杂化太阳能电池。通过扫描电镜、X射线衍射、光致发光和模拟太阳光光电性能测试,对ZnO的生长条件、晶体形貌及缺陷与太阳能电池性能之间的关系进行了系统研究。结果表明,ZnO的形貌和晶体缺陷的分布对杂化太阳能电池有重要影响,避免共混聚合物与ZnO缺陷聚集区的直接接触可有效消除电流泄漏。在电池结构方面,与ZnO纳米阵列块状结构杂化太阳能电池相比,共形结构的杂化太阳能电池可有效缩短空穴到金属电极的传输距离,增大聚合物与金属电极的接触面积,光电转换效率可提升64%~101%。     

Novel ZnO nanostructured electrodes for higher power conversion efficiencies in polymeric solar cells

1-Dimensional nanostructured ZnO electrodes have been demonstrated to be potentially interesting for their application in solar cells. Herein, we present a novel procedure to control the ZnO nanowire optoelectronic properties by means of surface modification. The nanowire surface is functionalized with ZnO nanoparticles in order to provide an improved contact to the photoactive P3HT:PCBM film that enhances the overall power conversion efficiency of the resulting solar cell. Charge extraction and transient photovoltage measurements have been used to successfully demonstrate that the surface modified nanostructured electrode contributes in enhancing the exciton dissociating ratio and in enlarging the charge lifetime as a consequence of a reduced charge recombination. Under AM1.5G illumination, all these factors contribute to a considerably large increase in photocurrent yielding unusually high conversion efficiencies over 4% and external quantum efficiencies of 87% at 550 nm for commercially available P3HT:PCBM based solar cells. The same approach might be equally used for polymeric materials under development to overcome the record reported efficiencies.     

Monte Carlo morphological modelling of a P3HT:PCBM bulk heterojunction organic solar cell

To deepen the understanding of morphology evolution in bulk heterojunction P3HT:PCBM organic photovoltaics system by thermal treatment, domain‐size‐dependent interfacial energies were first determined by coarse‐grained molecular dynamics modelling and then used in Monte Carlo simulations of the morphology evolution. Thereby initial conditions associated with optimal interfacial surface area, continuous volume, as well as domain sizes, and spatial distributions of the phase separated domains were identified. In line with earlier studies, a 1:1 P3HT:PCBM blend ratio is found to exhibit the most efficient morphology for exciton dissociation and charge transport. Our simulations reveal that preseeding of P3HT crystal at the anode side prior to the annealing process will be instrumental to pin the formation of P3HT at the favorable electrode especially when seeding exceeds a threshold of 10% surface coverage, whereas denser seeding patterns beyond the threshold did not improve the active layer morphology further. The observed trilayer depth profile (in the absence of preseeded P3HT crystals) implies that the commonly used thickness 100 nm of the active layer is not ideal for ensuring that donor and acceptor phases dominate at opposite ends of the active layer. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 270–279     

4,9‐Dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione functionalized copolymers for organic photovoltaic devices

The synthesis of conjugated polymers 1 – 5 functionalized with 4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione in the backbone is reported and their use in the construction of organic solar cells is demonstrated. Increasing the molar ratio of 2,7‐dibromo‐3,8‐dihexyl‐4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione, relative to 4,4′‐dihexyl‐5,5′‐dibromo‐2,2′‐bithiophene, in the copolymer synthesis significantly lowers the solubility of these polymers. The incorporation of highly conjugated 3,8‐dihexyl‐4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione unit into the polymer backbone has been confirmed by UV–vis absorption. The observation of decreasing quantum yield for the emission in the order of 1 , 2 , 3 is consistent with copolymers with different comonomer content. The power conversion efficiencies of solar cells using blends of these polymers with PCBM ([6,6]‐phenyl C₆₁‐butyric acid methyl ester) were determined to be 0.11% for polymer 1 , 0.33% for 2 , and 0.26% for 3 , respectively. Under identical white light illumination, the power conversion efficiency of the device based on polymer 2 /PCBM as the active layer was three times higher compared to that of device based on polymer 1 /PCBM. Owing to the limited solubility and poor film‐forming ability of polymer 3 , the power conversion efficiency of solar cell based on 3 /PCBM blend is lower than that of 2 /PCBM blend, but is still larger than that of 1 /PCBM blend. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2680–2688, 2008     

用CdSe/ZnS量子点提高体异质结有机太阳电池的效率

通过掺杂吸收光谱在可见光波段的量子点可提高聚合物对可见光的吸收,因此掺杂CdSe/ZnS核-壳结构量子点(CQDs)能提高聚(3-己基噻吩):[6,6]-苯基-C61-丁酸甲酯(P3HT:PCBM)体异质结太阳电池的能量转换效率.本文研究了CdSe/ZnS量子点在P3HT:PCBM中的不同掺杂比例及其表面配体对太阳电池光伏性能的影响,优化器件ITO(氧化铟锡)/PEDOT:PSS(聚(3,4-乙撑二氧噻吩:聚苯乙烯磺酸)/P3HT:PCBM:(CdSe/ZnS)/Al的能量转换效率达到了3.99%,与相同条件下没有掺杂量子点的参考器件ITO/PEDOT:PSS/P3HT:PCBM/Al相比,其能量转换效率提高了45.1%.     

Significance of miscibility in multidonor bulk heterojunction solar cells

Ternary organic blends have potential in realizing efficient bulk heterojunction (BHJ) organic solar cells by harvesting a larger portion of the solar spectrum than binary blends. Several challenging requirements, based on the electronic structure of the components of the ternary blend and their nanoscale morphology, need to be met in order to achieve high power conversion efficiency in ternary BHJs. The properties of a model ternary system comprising two donor polymers, poly(3-hexylthiophene) (P3HT) and a furan-containing, diketopyrrolopyrrole-thiophene low-bandgap polymer (PDPP2FT), with a fullerene acceptor, PC₆₁BM, were examined. The relative miscibility of PC₆₁BM with P3HT and PDPP2FT was examined using diffusion with dynamic secondary ion mass spectrometry (dynamic SIMS) measurements. Grazing incidence small and wide angle X-ray scattering analysis (GISAXS and GIWAXS) were used to study the morphology of the ternary blends. These measurements, along with optoelectronic characterization of ternary blend solar cells, indicate that the miscibility of the fullerene acceptor and donor polymers is a critical factor in the performance in a ternary cell. A guideline that the miscibility of the fullerene in the two polymers should be matched is proposed and further substantiated by examination of known well-performing ternary blends. The ternary blending of semiconducting components can improve the power conversion efficiency of bulk heterojunction organic photovoltaics. The blending of P3HT and PDPP2FT with PC₆₁BM leads to good absorptive coverage of the incident solar spectrum and cascading transport energy levels. The performance of this ternary blend reveals the impact of the miscibility of PC₆₁BM in each polymer as a function of composition, highlighting an important factor for optimization of ternary BHJs. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 237–246     

Vertical phase separation of conjugated polymer and fullerene bulk heterojunction films induced by high pressure carbon dioxide treatment at ambient temperature

The morphology of bulk-heterojunctions (BHJ) is critically important for conjugated polymer and fullerene blend solar cells. To alter the morphology, high pressure (gas phase) carbon dioxide (CO(2)) treatment is applied to poly(3-hexyl thiophene) (P3HT) and [6,6]-phenyl-C61 butyric acid methyl ester (PCBM) blend films under ambient temperature. This process can achieve vertically phase separated morphology such that PCBM distributes toward the film surface, which is suggested by secondary ion mass spectroscopy (SIMS), contact angle, X-ray photoelectron spectroscopy (XPS) and cross-sectional scanning electron microscope (SEM) studies. While pristine P3HT films do not show a significant change upon CO(2) treatment, pristine PCBM films are plasticized in high pressure CO(2). Thus, PCBM is selectively plasticized by CO(2) in the blend film and is drawn towards the surface due to depressed surface energy, although P3HT tends to distribute around the surface without CO(2). This stratification process can enhance solar cell performance. 55% improvement is achieved in the power conversion efficiency of the CO(2) treated device compared to the untreated one, indicating that CO(2) treatment can be a good candidate for optimizing the morphology and enhancing the performance of BHJ polymer solar cells.     

Effect of solvent additives on bulk heterojunction morphology of organic photovoltaics and their impact on device performance

Morphology of the active layer in an organic photovoltaic (OPV) device is known to have a significant impact on the device performance. It is, however, difficult to characterize nanoscale morphologies in detail, especially at the ensemble level. Herein, we report the utilization of small angle neutron scattering (SANS) to investigate variations in the nanoscale morphologies of the active layer of poly(3-hexylthiophene-2,5-diyl):[6,6]-phenyl-C₆₁-butyric acid methyl ester (P3HT:PCBM) bulk heterojunction OPV depending on the composition of casting solvent. Both the power law and the poly hard sphere model were utilized to characterize the state of the donor and acceptor components, respectively, from the obtained SANS data. Furthermore, the relationship between the nanoscale morphology and device performance is outlined. It was found that the use of 2-chlorophenol, a poor solvent for P3HT and, at the same time, a very good solvent for PCBM, leads to nanomorphology featuring ordered, highly crystalline P3HT and small (15.2 nm) PCBM domains. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 128–134     

Improvement of Power Conversion Efficiency of P3HT/PCBM Polymer Solar Cell Systems by Optimization of the Process Steps

In this work, different steps involved in the fabrication of polymer solar cells were optimized using P3HT/PCBM heterojunction. Steps included spinning speed for coating of the PEDOT:PSS layer, use of filter for the PEDOT:PSS layer, spinning speed for coating of the active layer, sequence of annealing of the active layer either before or after electrode deposition, and modification of the cooling mechanism (either by cooling rapidly or slowly after heating of the active layer). Investigation of these steps led to an improvement of the power-conversion efficiency (PCE) of the polymer solar cells, especially the last step involving the change of cooling mechanism, which improved PCE by 25%.     

Synthesis and photovoltaic properties of low‐bandgap 4,7‐dithien‐2‐yl‐2,1,3‐benzothiadiazole‐based poly(heteroarylenevinylene)s

Three novel low‐bandgap copolymers containing alkylated 4,7‐dithien‐2‐yl‐2,1,3‐benzothiadiazole (HBT) and different electron‐rich functional groups (dialkylfluorene (PFV‐HBT), dialkyloxyphenylene (PPV‐HBT) and dialkylthiophene (PTV‐HBT)) were prepared by Horner polycondensation reactions and characterized by ¹H NMR, gel permeation chromatography, and elemental analysis. The alkyl side chain brings these polymeric materials good solubility in common organic solvents, which is critical for the manufacture of solar cells in a cost‐effective manner. The copolymers exhibit low optical bandgap from 1.48 to 1.83 eV. The highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy levels of the copolymers were measured by cyclic voltammetry. Theoretical calculations revealed that the variation laws of HOMO and the LUMO energy levels are well consistent with cyclic voltammetry measurement. The bulk heterojunction photovoltaic devices with the structure of ITO/PEDOT‐PSS/polymer:PCBM/LiF/Al were fabricated by using the three copolymers as the donor and (6,6)‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) as the acceptor in the active layer. The device based on PTV‐HBT:PCBM (1:4 w/w) achieved a power conversion efficiency of 1.05% under the illumination of AM 1.5, 100 mW/cm². © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Flexible Polymer–Organic Solar Cells Based on P3HT:PCBM Bulk Heterojunction Active Layer Constructed under Environmental Conditions

In this study, some crucial parameters were determined of flexible polymer–organic solar cells prepared from an active layer blend of poly(3-hexylthiophene) (P3HT) and the fullerene derivative [6,6]-phenyl-C₆₁-butyric acid methyl ester (PCBM) mixed in 1:1 mass ratio and deposited from chlorobenzene solution by spin-coating on poly(ethylene terephthalate) (PET)/ITO substrates. Additionally, the positive effect of an electron transport layer (ETL) prepared from zinc oxide nanoparticles (ZnO np) on flexible photovoltaic elements’ performance and stability was investigated. Test devices with above normal architecture and silver back electrodes deposed by magnetron sputtering were constructed under environmental conditions. They were characterized by current-voltage (I–V) measurements, quantum efficiency, impedance spectroscopy, surface morphology, and time–degradation experiments. The control over morphology of active layer thin film was achieved by post-deposition thermal treatment at temperatures of 110–120 °C, which led to optimization of device morphology and electrical parameters. The impedance spectroscopy results of flexible photovoltaic elements were fitted using two R||CPE circuits in series. Polymer–organic solar cells prepared on plastic substrates showed comparable current–voltage characteristics and structural properties but need further device stability improvement according to traditionally constructed cells on glass substrates.     

Optical and Electronic Properties of Organic Photovoltaic Wires and Fabrics

The characteristics of a power producing flexible wire based on organic photovoltaics (OPV) and the processes by which they are produced are described in this paper. A set of materials and coating formulations used on the electrode wires are very similar to those used in the development of two dimensional photovoltaic cells and modules. The active layer of the primary electrode wire comprises the bulk heterojunction-forming P3HT/PCBM (1:1 weight ratio) that has been extensively studied in planar cells. A second wire, which is wrapped around the coated, primary electrode wire, serves as the counter electrode. Ray tracing analysis indicates that light incident on the wires is focused by the cladding onto to the active layer, coated, primary electrode wire even when it is completely shadowed by the counter electrode. Furthermore, when the counter electrode is in a position that partially shadows the primary wire, a significant percentage of the light is reflected by the counter electrode onto the primary electrode.

Many hundreds of feet of OPV wire have been produced continuously for experimental purposes, and the process is capable of producing any length of PV wire desired. Efficiency values of a 200 foot spool of PV wire ranges from 2.79% to 3.27%.     

Nanocomposites composed of P3HT:PCBM and nanoparticles synthesized by laser ablation of a bulk PbS target in liquid

Nanoparticles synthesized by laser ablation of bulk target materials in liquids have ligand-free surfaces since no chemical precursors are used for their synthesis, and thus, they are ideally suited for applications in the fabrication of organic solar cells in which the properties of the interface between the nanoparticles and the polymer blend matrix largerly determine the exciton splitting and transport of carriers to the external electrodes, properties crucial for the device operation and performance. Narrow band gap semiconducting quantum dots can act as sensitizers, increasing the absorption of the device active layer in the infrared part of the solar spectrum. In this work, a bulk PbS target was laser ablated (450 fs, 1,064 nm, 1 kHz) in ethanol for the synthesis of nanoparticle colloidal solutions. The solutions exhibit a broad absorption which extends at the longest wavelength measured of ~1,700 nm and beyond. The nanoparticles were directly mixed with the blend P3HT:PCBM for the formation of nanocomposites. The nanocomposites with the nanoparticles exhibit lower transmission in the whole spectral range as compared to the blend without the nanoparticles.     

Conjugated polymer‐functionalized graphite oxide sheets thin films for enhanced photovoltaic properties of polymer solar cells

In this study, the maleimide‐thiophene copolymer‐functionalized graphite oxide sheets (PTM21‐GOS) and carbon nanotubes (PTM21‐CNT) were developed for polymer solar cell (PSC) applications. The grafting of PTM21‐OH onto the CNT and GO sheets was confirmed using FTIR spectroscopy. PTM21‐CNT and PTM21‐GOS exhibited excellent dispersal behavior in organic solvents. Better thermal stability was observed for PTM21‐CNT and PTM21‐GOS as compared with that for PTM21‐OH. In addition, the optical band gaps of PTM21‐GOS and PTM21‐CNT were lower than that of PTM21‐OH. We incorporated PTM21‐GOS and PTM21‐CNT individually into poly(3‐hexylthiophene) (P3HT)/[6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) blends for use as photoconversion layers of PSCs. Good distributional homogeneity was observed for PTM21‐GOS or PTM21‐CNT in the P3HT/PCBM blend film. The UV–vis absorption peaks of the blend films red‐shifted slightly upon increasing the content of PTM21‐GOS or PTM21‐CNT. The band gap energies and LUMO/HOMO energy levels of the P3HT/PTM21‐GOS and P3HT/PTM21‐CNT blend films were slightly lower than those of the P3HT film. The conjugated polymer‐functionalized PTM21‐GOS and PTM21‐CNT behaved as efficient electron acceptors and as charge‐transport assisters when incorporated into the photoactive layers of the PSCs. PV performance of the PSCs was enhanced after incorporating PTM21‐GOS or PTM21‐CNT in the P3HT/PCBM blend. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013