Synthesis of ammonia at atmospheric pressure with Ce0.8M0.2O2−δ (M = La,Y, Gd,Sm) and their proton conduction at intermediate temperature

Ionic conduction in fluorite-type structure oxide ceramics Ce_0.8M_0.2O_2−δ (M = La, Y, Gd, Sm) at temperature 400–800 °C was systematically studied under wet hydrogen/dry nitrogen atmosphere. On the sintered complex oxides as solid electrolyte, ammonia was synthesized from nitrogen and hydrogen at atmospheric pressure in the solid states proton conducting cell reactor by electrochemical methods, which directly evidenced the protonic conduction in those oxides at intermediate temperature. The rate of evolution of ammonia in Ce_0.8M_0.2O_2−δ (M = La, Y, Gd, Sm) is up to 7.2 × 10^− 9, 7.5 × 10^− 9, 7.7 × 10^− 9, 8.2 × 10^− 9 mol s^− 1 cm^− 2, respectively.     

Oxygen diffusion and surface exchange studies on (La0.75Sr0.25)0.95Cr0.5Mn0.5O3−δ

Oxygen tracer diffusion coefficient (D^⁎) and surface exchange coefficient (k^⁎) have been measured for (La_0.75Sr_0.25)_0.95Cr_0.5Mn_0.5O_3−δ using isotopic exchange and depth profiling by secondary ion mass spectrometry technique as a function of temperature (700–1000 °C) in dry oxygen and in a water vapour-forming gas mixture. The typical values of D^⁎ under oxidising and reducing conditions at ∼ 1000 °C are 4 × 10^− 10 cm² s^− 1 and 3 × 10^− 8 cm² s^− 1 respectively, whereas the values of k^⁎ under oxidising and reducing conditions at ∼ 1000 °C are 5 × 10^− 8 cm s^− 1 and 4 × 10^− 8 cm s^− 1 respectively. The apparent activation energies for D^⁎ in oxidising and reducing conditions are 0.8 eV and 1.9 eV respectively.     

Structural,XPS and impedance analysis of LixCoVO4 (x = 0.8, 1.0, 1.2)

Lithium cobalt vanadate Li_xCoVO₄ (x = 0.8; 1.0; 1.2) has been prepared by a solid state reaction method. The XRD analysis confirms the formation of the sample. A new peak has been observed for Li_1.0CoVO₄ and for Li_1.2CoVO₄ indicating the formation of a new phase. The XPS analysis indicates the reduction in the oxidation of vanadium and oxygen with the addition of Li in Li_xCoVO₄ (x = 0.8, 1.0, 1.2). The impedance analysis gives the conductivity value as 2.46 × 10^− 5, 6.16 × 10^− 5, 9 × 10^− 5 Ω^− 1 cm^− 1 for Li_xCoVO₄ (x = 0.8; 1.0; 1.2), all at 623 K. The similarity in the bulk activation energy (E_a) and the activation enthalpy for migration of ions (E_ω) indicate that the conduction in Li_1.2CoVO₄ has been due to hopping mechanism.     

Structure,stability and electrical properties of the La(2−x)SrxMnO4±δ solid solution series

Single phase materials of the La_(2−x)Sr_xMnO_4±δ (0.6 ≤ x ≤ 2.0) solid solution series were prepared via solid state reaction. The structure of each material was examined at room temperature and determined to be tetragonal for all phases examined. An expansion in lattice volume was observed on increasing lanthanum content. The stability and thermal expansion of each member of the solid solution series was determined via the use of in situ high temperature X-ray diffraction. It was found that all materials remained stable up to a temperature of 800 °C. Thermal expansion coefficients were found to be in the region of 15 × 10^− 6 K^− 1 for La_(2−x)Sr_xMnO_4±δ compounds where x > 1.4. The electrical conductivity of each phase was also determined over a similar temperature range with a maximum value of ∼6 Scm^− 1 at 900 °C for the x = 1.8 phase.     

A Boubaker polynomials expansion scheme (BPES)-related protocol for measuring sprayed thin films thermal characteristics

Measurements of In₂S₃ and ZnIn₂S₄ sprayed thin films thermal characteristics have been carried out using the photodetection technique. The thermal conductivity k and diffusivity D were obtained using a new protocol based on photothermal signal parameters analysis. Measured values of k and D were respectively, (15.2 ± 0.85) W m⁻¹K⁻¹ and (69.8 ± 7.1) × 10⁻⁶ m²s⁻¹ for In₂S₃, (7.2 ± 0.7) W m⁻¹K⁻¹ and (32.7 ± 4.3) × 10⁻⁶ m²s⁻¹ for ZnIn₂S₄. These values are extremely important since similar compounds are more and more proposed as Cd-free alternative materials for solar cells buffer layers.     

Transport and phase dynamics of poly(vinyl pyrrolidone) doped plastically crystalline N-methyl-N-propylpyrrolidinium tetrafluoroborate

The plastic crystal phase forming N-methyl-N-propylpyrrolidinium tetrafluoroborate organic salt (P₁₃BF₄) was combined with 2, 5 and 10 wt.% poly(vinyl pyrrolidone) (PVP). The ternary 2 wt.% PVP/2 wt.% LiBF₄/P₁₃BF₄ was also investigated. Thermal analysis, conductivity, optical thermomicroscopy, and Nuclear Magnetic Resonance (¹¹B, ¹⁹F, ¹H, ⁷Li) were used to probe the fundamental transport processes. Both the onset of phase I and the final melting temperature were reduced with increasing additions of PVP. Conductivity in phase I was 2.6 × 10^− 4 S cm^− 1 5.2 × 10^− 4 S cm^− 1 1.1 × 10^− 4 S cm^− 1 and 3.9 × 10^− 5 S cm^− 1 for 0, 2, 5 and 10 wt.%PVP/P₁₃BF₄, respectively. Doping with 2 wt.% LiBF₄ increased the conductivity by up to an order of magnitude in phase II. Further additions of 2 wt.% PVP slightly reduced the conductivity, although it remained higher than for pure P₁₃BF₄.     

Ionic conductivity of polymer electrolyte membranes based on polyphosphazene with oligo(propylene oxide) side chains

A polyphosphazene [NP(NHR)₂]_n with oligo[propylene oxide] side chains − R = –[CH(CH₃)–CH₂O]_m–CH₃ (m = 6 – 10) was synthesized by living cationic polymerisation and polymer-analogue substitution of chlorine from the intermediate precursor [NPCl₂]_n using the corresponding primary amine RNH₂. The polymer had an average molecular weight of 3.3 × 10⁵ D. Polymer electrolytes with different concentrations of dissolved lithium triflate (LiCF₃SO₃) were prepared. Mechanically stable polymer electrolyte membranes were formed using UV radiation induced crosslinking of the polymer salt mixture in the presence of benzophenone as photoinitiator. The glass transition temperature of the parent polymer was found to be − 75 °C before cross linking. It increases after crosslinking and with increasing amounts of salt to a maximum of − 55 °C for 20 wt.% LiCF₃SO₃. The ionic conductivity was determined by impedance spectroscopy in the temperature range 0–80 °C. The highest conductivity was found for a salt concentration of 20 wt.% LiCF₃SO₃: 6.5 × 10^− 6 S·cm^− 1 at 20 °C and 2.8 × 10^− 4 S cm^− 1 at 80 °C. The temperature dependence of the conductivities was well described by the MIGRATION concept.     

Interfacial energies of carbon tetrabromide

The equilibrated grain boundary groove shapes for solid carbon tetrabromide (CTB) in equilibrium with its melt were directly observed by using a horizontal temperature gradient stage. From the observed grain boundary groove shapes, Gibbs–Thomson coefficient (Γ) and solid–liquid interfacial energy (σ_SL) and grain boundary energy (σ_gb) of CTB have been determined to be (7.88 ± 0.8) × 10⁻⁸ K m, (6.91 ± 1.04) × 10⁻³ J m⁻² and (13.43 ± 2.28) × 10⁻³ J m⁻², respectively. The ratio of thermal conductivity of equilibrated liquid phase to solid phase for CTB has also been measured to be 0.90 at its melting temperature. The value of σ_SL for CTB obtained in present work was compared with the values of σ_SL determined in the previous works for same material and it was seen that the present result is in good agreement with previous works.     

Device linearity improvement and current enhancement utilizing high-to-low doping-channel FETs

We report device linearity improvement and current enhancement in both a heterostructure FET (HFET) and a camel-gate FET (CAMFET) using InGaAs/GaAs high-low and GaAs high-medium-low doped channels, respectively. In an HFET, a low doped GaAs layer was employed to build an excellent Schottky contact. In a GaAs CAMFET, a low doped layer together withn⁺andp⁺layers formed a high-performance majority camel-diode gate. Both exhibit high effective potential barriers of >1.0 V and gate-to-drain breakdown voltages of >20.0 V (atI_g=1.0 mA mm⁻¹). A thin, high doped channel was used to enhance current drivability and to improve the transconductance linearity. A 2×100 μm²HFET had a peak transconductance of 230 mS mm⁻¹and a current density greater than 800 mA mm⁻¹. The device had a transconductance of more than 80 percent of the peak value over a wide drain current range of 200 to 800 mA mm⁻¹. A 1.5×100 μm²CAMFET had a peak transconductance of 220 mS mm⁻¹and a current density greater than 800 mA mm⁻¹. Similarly, the device had a transconductance of more than 80 percent of the peak value over a wide drain current range of 160 to 800 mA mm⁻¹. The improvement of device linearity and the enhancement of current density suggest that high-to-low doped-channel devices for both an HFET and a CAMFET are suitable for high-power large signal circuit applications.     

Phase stability and oxygen non-stoichiometry of SrCo0.8Fe0.2O3−δ measured by in situ neutron diffraction

The phase stability, oxygen stoichiometry and expansion properties of SrCo_0.8Fe_0.2O_3−δ (SCF) were determined by in situ neutron diffraction between 873 and 1173 K and oxygen partial pressures of 5 × 10^− 4 to 1 atm. At a pO₂ of 1 atm, SCF adopts a cubic perovskite structure, space group Pm3¯m, across the whole temperature range investigated. At a pO₂ of 10^− 1 atm, a two-phase region exists below 922 K, where the cubic perovskite phase coexists with a vacancy ordered brownmillerite phase, Sr₂Co_1.6Fe_0.4O₅, space group Icmm. A pure brownmillerite phase is present at pO₂ of 10^− 2 and 5 × 10^− 4 atm below 1020 K. Above 1020 K, the brownmillerite phase transforms to cubic perovskite through a two-phase region with no brownmillerite structure observed above 1064 K. Large distortion of the BO₆ (B = Co, Fe) octahedra is present in the brownmillerite structure with apical bond lengths of 2.2974(4) Å and equatorial bond lengths of 1.9737(3) Å at 1021 K and a pO₂ of 10^− 2 atm. SCF is highly oxygen deficient with a maximum oxygen stoichiometry, 3 − δ, measured in this study of 2.58(2) at 873 K and a pO₂ of 1 atm and a minimum of 2.33(2) at 1173 K and a pO₂ of 5 × 10^− 4 atm. Significant differences in lattice volume and expansion behavior between the brownmillerite and cubic perovskite phases suggest potential difficulties in thermal cycling of SrCo_0.8Fe_0.2O_3−δ membranes.     

High room-temperature pyroelectric response of MgO-modified Pb0.99(Zr0.95Ti0.05)0.98Nb0.02O3 ceramics

The dielectric and pyroelectric responses of MgO-modified Pb_0.99(Zr_0.95Ti_0.05)_0.98Nb_0.02O₃ ceramics were investigated near F_R(LT)–F_R(HT) phase transition. It was found that MgO additive reduced the F_R(LT)–F_R(HT) phase transition temperature from 41 °C to room temperature (24 °C). Superior room-temperature pyroelectric properties were obtained in the composition of 0.10 wt% MgO addition without DC bias. The largest pyroelectric coefficient, 65 × 10⁻⁸ C cm⁻² K⁻¹, was detected. Accordingly, the detectivity figures of merit F_d had maximum values of 20 × 10⁻⁵ Pa^−1/2, and especially the voltage responsivity F_v = 0.91 m²C⁻¹ is the highest value reported so far among all pyroelectric materials. It shows promising potential for application in uncooled pyroelectric infrared detector.     

Mixed conductivity,stability and thermomechanical properties of Ni-doped La(Ga,Mg)O3−δ

Perovskite-type LaGa_0.65Mg_0.15Ni_0.20O_3−δ exhibiting oxygen transport comparable to that in K₂NiF₄-type nickelates was characterized as a model material for ceramic membrane reactors, employing mechanical tests, dilatometry, oxygen permeability and faradaic efficiency measurements, thermogravimetry (TG), and determination of the total conductivity and Seebeck coefficient in the oxygen partial pressure range from 10^− 15 Pa to 40 kPa. Within the phase stability domain which is similar to La₂NiO_4+δ, the defect chemistry of LaGa_0.65Mg_0.15Ni_0.20O_3−δ can be adequately described by the ideal solution model with oxygen vacancies and electron holes to be the only mobile defects, assuming that Ni²⁺ may provide two energetically equivalent sites for hole location. This assumption is in agreement with the density of states, estimated from thermopower, and the coulometric titration and TG data suggesting Ni⁴⁺ formation in air at T < 1150 K. The hole conductivity prevailing under oxidizing conditions occurs via small-polaron mechanism as indicated by relatively low, temperature-activated mobility. The ionic transport increases with vacancy concentration on reducing p(O₂) and becomes dominant at oxygen pressures below 10^− 7–10^− 5 Pa. The average thermal expansion coefficients in air are 11.9 × 10^− 6 and 18.4 × 10^− 6 K^− 1 at 370–850 and 850–1270 K, respectively. The chemical strain of LaGa_0.65Mg_0.15Ni_0.20O_3−δ ceramics at 1073–1123 K, induced by the oxygen partial pressure variations, is substantially lower compared to perovskite ferrites. The flexural strength determined by 3-point and 4-point bending tests is 167–189 MPa at room temperature and 85–97 MPa at 773–1173 K. The mechanical properties are almost independent of temperature and oxygen pressure at p(O₂) = 1–2.1 × 10⁴ Pa and 773–1173 K.     

Biosynthesis of gold nanoparticles by Aspergillum sp. WL-Au for degradation of aromatic pollutants

A simple method for synthesis of gold nanoparticles (AuNPs) using Aspergillum sp. WL-Au was presented in this study. According to UV–vis spectra and transmission electron microscopy images, the shape and size of AuNPs were affected by different parameters, including buffer solution, pH, biomass and HAuCl₄ concentrations. Phosphate sodium buffer was more suitable for extracellular synthesis of AuNPs, and the optimal conditions for AuNPs synthesis were pH 7.0, biomass 100 mg/mL and HAuCl₄ 3 mM, leading to the production of spherical and pseudo-spherical nanoparticles. The biosynthesized AuNPs possessed excellent catalytic activities for the reduction of 2-nitrophenol, 3-nitrophenol, 4-nitrophenol, o-nitroaniline and m-nitroaniline in the presence of NaBH₄, and the catalytic rate constants were calculated to be 6.3×10⁻³ s⁻¹, 5.5×10⁻³ s⁻¹, 10.6×10⁻³ s⁻¹, 8.4×10⁻³ s⁻¹ and 13.8×10⁻³ s⁻¹, respectively. The AuNPs were also able to catalyze the decolorization of various azo dyes (e.g. Cationic Red X-GRL, Acid Orange II and Acid scarlet GR) using NaBH₄ as the reductant, and the decolorization rates reached 91.0–96.4% within 7 min. The present study should provide a potential candidate for green synthesis of AuNPs, which could serve as efficient catalysts for aromatic pollutants degradation.     

Ionic and electronic conductivities,stability and thermal expansion of La10 − x(Si,Al)6O26 ± δ solid electrolytes

Apatite-type La_10 − xSi_6 − yAl_yO_{27 − 3x/2 − y/2} (x = 0–0.33; y = 0.5–1.5) exhibit predominant oxygen ionic conductivity in a wide range of oxygen partial pressures. The conductivity of silicates containing 26.50–26.75 oxygen atoms per formula unit is comparable to that of gadolinia-doped ceria at 770–870 K. The average thermal expansion coefficients are (8.7–10.8) × 10^− 6 K^− 1 at 373–1273 K. At temperatures above 1100 K, silicon oxide volatilization from the surface layers of apatite ceramics and a moderate degradation of the ionic transport with time are observed under reducing conditions, thus limiting the operation temperature of Si-containing solid electrolytes.     

Effect of series resistance on the performance of silicon Schottky diode in the presence of tin oxide layer

The current–voltage (I–V) characteristics of Al/SnO₂/p-Si (MIS) Schottky diodes prepared by means of spray deposition method have been measured at 80, 295 and 350 K. In order to interpret the experimentally observed non-ideal Al/SnO₂/p-Si Schottky diode parameters such as, the series resistance R_s, barrier height Φ_B and ideality factor n, a novel calculation method has been reported by taking into account the applied voltage drop across interfacial oxide layer V_i and ideality factor n in the current transport mechanism. The values obtained for V_i were subtracted from the applied voltage values V and then the values of R_s were recalculated. The parameters obtained by accounting for the voltage drop V_i have been compared with those obtained without considering the above voltage drop. It is shown that the values of R_s estimated from Cheung’s method were strongly temperature-dependent and decreased with increasing temperature. It is shown that the voltage drop across the interfacial layer will increase the ideality factor and the voltage dependence of the I–V characteristics. The interface state density N_ss of the diodes has an exponential growth with bias towards the top of the valance band for each temperature; for example, from 2.37 × 10¹³ eV⁻¹ cm⁻² in 0.70−E_v eV to 7.47 × 10¹³ eV⁻¹ cm⁻² in 0.62−E_v eV for 295 K. The mean N_ss estimated from the I–V measurements decreased with increasing the temperature from 8.29 × 10¹³ to 2.20 × 10¹³ eV⁻¹ cm⁻².     

M/Li+(M = Mg2+, Zn2+, and Mn2+) ion-exchange on lithium ion-conducting perovskite-type oxides and their properties

Lithium ions of perovskite-type lithium ion conductor La_0.55Li_0.35TiO₃ were replaced by divalent Mg²⁺, Zn²⁺, and Mn²⁺ ions in an ion-exchange reaction using molten chlorides. The polycrystalline Mg-exchanged and Zn-exchanged samples are solid electrolytes for divalent Mg²⁺ and Zn²⁺ ions, whose dc ionic conductivities (σ = 2.0 × 10^− 6 S cm^− 1 at 558 K for the Mg-exchanged sample, La_0.56(2)Li_0.02(1)Mg_0.16(1)TiO_3.01(2) and σ = 1.7 × 10^− 6 S cm^− 1 at 708 K for the Zn-exchanged samples, La_0.55(1)Li_0.0037(2)Zn_0.15(1)TiO_2.98(2)) were compared to those of the known highest Mg²⁺ and Zn²⁺ inorganic solid electrolytes. The Mn-exchanged sample, then, showed paramagnetic behavior in the temperature range of 2 to 300 K. The Mn ions in the exchanged sample are divalent and the spin configuration is in high spin state (S = 5/2).     

Oxygen permeation characteristics of zirconia with surface modification

Yttria-stabilized zirconia (YSZ) can be used as an oxygen-permeating membrane at elevated temperature (> 1400 °C) due to its chemical and mechanical stability. It was previously shown that the oxygen transport through YSZ membrane in reducing oxygen partial pressure (P_O2) was highly influenced by the surface-exchange kinetics that can be improved by porous surface coating layers such as YSZ, GDC (Gd-doped ceria) or YSZ–GDC mixture [H.J. Park, G.M. Choi, J. Eur. Ceram. Soc. 25 (2005) 2577]. However, the increased oxygen flux was still lower than that estimated assuming bulk-diffusion limit and rapidly decreased with time due to the sintering of coating layers and the reaction between bulk YSZ and coating layers. In this study, the oxygen fluxes through YSZ with LaCrO₃, GDC + LaCrO₃ (bilayer), LaCrO₃ + 5 wt.% GDC (mixture), or LaCr_0.7Co_0.3O₃ coatings were measured under controlled P_O2 gradient (permeate-side P_O2: ∼ 3 × 10^− 12 atm, feed-side P_O2: 2 × 10^− 10–2 × 10^− 8 atm) at 1600 °C. The oxygen flux drastically increased with these coatings. The highest increase in oxygen flux was shown with GDC + LaCrO₃ (bilayer) coating and was maintained for a long time. The presence of highly catalytic Ce ions while maintaining porous structure in the coating layer may explain the observation. The prevention of formation of resistive layer due to ceria coating may also be partly responsible for the observation.     

Fabrication of thin-film transistor based on self-assembled single-walled carbon nanotube network

Thin-film transistor based on controllable electrostatic self-assembled monolayer single-wall carbon nanotubes (SWNTs) network has been fabricated by varying the density of nanotubes on the silicon substrate. The densities of SWNTs network have been investigated as a function of concentration and assembly time. It has been observed that the density of SWNTs network increases from 0.6 µm⁻² to 2.1 µm⁻², as the average on-state current (I_on) increases from 0.5 mA to 1.47 mA. The device has a current on/off ratio (I_on/I_off) of 1.3×10⁴ when I_on reaches to 1.34 mA.     

Synthesis and investigations on the stability of La0.8Sr0.2CuO2.4+δ at high temperatures

For application in solid oxide fuel cells La_0.8Sr_0.2CuO_2.4+δ was synthesized and the phase evolution was characterized after quenching from different temperatures and after slow cooling. A single phase perovskite was found after quenching from 950 °C. The electrical conductivity of the La_0.8Sr_0.2CuO_2.4+δ perovskite exhibited metallic behavior reaching values of about 270 S/cm at 800 °C in air. The thermal expansion between 30 and 800 °C gave a thermal expansion coefficient of 11.1 × 10^− 6 K^− 1.At higher temperatures, the perovskite was transformed to the K₂NiF₄-type structure via an intermediate stage that can be best described as a LaSrCuO₄ phase with preferential growing of {020} lattice planes. After sintering at 1100 °C and slow cooling in the furnace a phase mixture of (La,Sr)CuO_4+δ and (La,Sr)CuO_2.4+δ perovskite was obtained. This phase mixture showed higher electrical conductivity (400 S/cm at 800 °C) and smaller thermal expansion coefficient (9.6 × 10^− 6 K^− 1) than the single phase La_0.8Sr_0.2CuO_2.4+δ perovskite.     

Synthesis and characterization of (Pr0.75Sr0.25)1 − xCr0.5Mn0.5O3 − δ as anode for SOFCs

The complex perovskite (Pr_0.75Sr_0.25)_1 − xCr_0.5Mn_0.5O_3 − δ (PSCM) has been prepared and studied as possible anode material for high-temperature solid oxide fuel cells (SOFCs). PSCM exhibits GdFeO₃-type structure and is both physically and chemically compatible with the conventional YSZ electrolyte. The reduction of PSCM resulted in structural change from orthorhombic Pbnm to cubic Pm-3m. Selected area electron diffraction (SAED) analysis on the reduced phases indicated the presence of a √2 × √2 × 2 superlattice. The total conductivity values of ∼ 75% dense Pr_0.75Sr_0.25Cr_0.5Mn_0.5O_3 − δ at 900 °C in air and 5% H₂/Ar are 9.6 and 0.14 S cm^− 1 respectively. The conductivity of PSCM drops with decreasing Po₂ and is a p-type conductor at all studied Po₂. The average TEC of Pr_0.75Sr_0.25Cr_0.5Mn_0.5O_3 − δ is 9.3 × 10^− 6 K^− 1, in the temperature range of 100–900 °C and is close to that of YSZ electrolyte. The anode polarization resistance of PSCM in wet 5%H₂ is 1.31 Ω cm² at 910 °C and in wet CH₄ at 930 °C; the polarization resistance is 1.29 Ω cm². PSCM was unstable at 900 °C in unhumidified hydrogen. Cell performance measurements carried out using graded PSCM and La_0.8Sr_0.2MnO₃ as anode and cathode respectively yielded a maximum power density of 0.18 W cm^− 2 in wet 5%H₂/Ar at 910 °C and the corresponding current density was 0.44 A cm^− 2 at 0.4 V. The activation energy for the electrochemical cell operating in wet (3% H₂O) 5%H₂/Ar fuel is 85 kJ mol^− 1.