重离子的束内散射

本文在Bjorken和Mtingwa束内散射理论的基础上进一步推导出了束内散射率的普遍表达式,并将该表达式应用于HIRFL—CSR的磁铁结构(lattice),计算并得到了束流横向发射度和纵向动量散度随时间变化的规律,结果表明,束内散射不会成为CSRlattice设计的障碍.     

HIRFL–CSR主环电子冷却装置调试

介绍了在HIRFL–CSR主环电子冷却装置上首次设计的能够产生空心电子束的电子枪阴极. 在弯曲螺线管内采用了静电偏转电极,冷却段采用了高磁场平行度螺线管设计,在IMP与BINP的合作下完成了电子冷却装置,测量了电子束剖面及密度分布、冷却段磁场平行度、电子枪和收集器的性能,实验验证了静电偏转电极的优越性,调试结果表明实现了预期的设计目标.     

CSR电子冷却系统强流电子束包络的振荡特性

 HIRFL CSR的电子冷却系统是采用强流电子束对重离子束进行冷却。在冷却段漂移管区，由于强流电子束自身的空间电荷场和螺线管磁场的作用，使得电子束的包络发生振荡。通过求解电子束的横向包络方程，研究了强流电子束包络随电子束参数和螺线管聚焦磁场的变化关系。计算结果表明：对于不同的电子束能量和磁场，电子束包络的振荡频率也不相同；在相同的条件下，磁场越强，电子束包络振荡幅度越小，电子束能量越大，其包络的振荡频率也越快。     

CSR电子冷却系统电子束空间电荷效应对电子束温度的影响

 通过求解电子冷却系统中冷却段漂移管区的强流电子束产生的空间电荷场,研究了电子束空间电荷效应对电子温升的影响。结合HIRFL CSR电子冷却系统的典型参数,得到了电子在自身空间电荷场和纵向螺线管磁场组成的交叉场作用下产生的漂移速度和由此引起的附加温度大小,并指出减小电子束空间电荷效应的方法。     

重离子束的随机冷却系统设计研究

随机冷却系统有助于提高兰州重离子冷却储存环（ＣＳＲ）中束流累积效率，减小束流发射度．首先通过Ｆｏｋｋｅｒ－Ｐｌａｎｃｋ方程的建立，解出了某种初始分布下粒子分布的时间演化结果，并模拟了冷却过程；然后结合ＣＳＲ物理设计参数，计算了部分典型被加速离子的冷却时间，同时比较了电子冷却和随机冷却的冷却力，得出了一些结论；最后提出了硬件设计方案. Stochastic cooling system in Cooling Storage Ring (CSR) at Lanzhou will help to cool beam phase space and increase the accumulation ratio and efficency. In this paper, a Fokker Planck eqution is described and used to simulate cooling process.According to the main parameters of CSR,cooling time of some typical ions has been calculated and the cooling forces of electron cooling and stochastic cooling are compared. Finally, A hardware designing plan is proposed.     

HIRFL-CSR电子冷却系统空心电子束性能研究

 电子冷却系统中冷却力的大小与电子束的温度密切相关。由于强流电子束自身产生的空间电荷场,使得电子束的速度离散,增加了电子束温度,降低了冷却效率。为了减小空间电荷效应,HIRFL CSR的电子冷却系统将首次采用空心电子束对储存环中的重离子束流进行冷却。通过分析实心电子束和空心电子束的空间电荷场,研究了其对电子束速度和温度的影响。     

兰州重离子加速器冷却储存环束流累积研究

对兰州重离子加速器冷却储存环加速器主体的主要功能环——主环的束流累积方法和设计进行了研究 .为了使主环对不同种类的重离子束流都具有较强的累积能力 ,在设计时考虑采用电子冷却参与下的两种束流累积方法 :多次多圈注入和射频堆积 .对这两种方法 ,电子冷却的冷却时间都是将束流累积到高流强的关键因素. The beam accumulation methods of HIRFL CSR(Heavy Ion Research Facility of Lanzhou and Cooler Storage Rings) project were studied. Two accumulation methods will be adopted to increase the beam intensity of CSRm. For both multiple multi turn injection method and RF stacking method, electron cooling of beam plays an important role.     

兰州重离子冷却储存环工程

兰州重离子加速器冷却储存环是兰州重离子研究装置的后续工程 .它的建造目的是将重离子束的能量提高到 1 Ge V/u附近 ,同时利用储存环电子冷却技术将束流品质提高一个数量级 ,并提供更多种类的重离子束 ,以开展更广范围和更高精度的物理实验 .兰州重离子加速器冷却储存环是一个双储存环系统 ,由一个主环和一个实验环构成 .对其总体布局、总体参数、主要功能进行了介绍. HIRFL- CSR, a new accelerator project at the Heavy Ion Research Facility in Lanzhou (HIRFL), is a multipurpose Cooling Storage Ring system which consists of a main ring (CSRm) and an experimental ring (CSRe). Beams from HIRFL will be accumulated and accelerated in CSRm, and then transported to CSRe for internal target experiments. The layout, major parameters and main functions of the CSR were described.     

四元裂解位相调制实现相干光通过散射介质聚焦

光在不均匀介质中传播会受到散射的干扰,在这些散射材料中,例如粉末、生物组织、亚波长颗粒对入射光多次散射使得出射光无法聚焦,从而在接收平面形成散斑.本文提出四元裂解位相调制方法对入射相干光场进行调制,使其通过散射介质聚焦.此方法利用入射光场全场调制,充分考虑光场单元之间的干涉作用,从整个空间光调制器的调制面开始,逐层进行四元裂解及位相优化.运用此方法在实验中实现了相干光的前向散射和后向散射有效聚焦,这为生物医学领域中通过散射介质成像提供了新的思路和方法.     

HIRFL—CSR电子冷却装置的电子枪设计

 从理论上推导并分析了绝热加速原理，进而应用改进的EGUN程序对HIRFL – CSR冷却装置电子枪进行了模拟设计。给出了电子束的横向温度随电极结构和螺线管纵向磁场的变化情况。计算结果表明：在冷却装置的整个工作能量范围内，可以获得横向温度低于0.1eV的电子束。     

热蒸发与离子束溅射制备LaF3薄膜的光学特性

研究了钼舟热蒸发工艺和离子束溅射方法制备的单层LaF₃薄膜的特性。首先,采用分光光度计测量了LaF₃薄膜的透射率和反射率光谱,使用不同模型拟合得出薄膜的折射率和消光系数。然后,采用应力仪测量了加热和降温过程中LaF₃薄膜的应力-温度曲线。最后,采用X射线衍射仪测试了薄膜的晶体结构。实验结果表明,热蒸发制备的LaF₃（RH LaF₃）存在折射率的不均匀性,在193 nm,其折射率和消光系数分别为1.687和5×10^-4,而离子束溅射制备的LaF₃（IBS LaF₃）折射率和消光系数分别为1.714和9×10^-4。两种薄膜表现出相反的应力状态,RH LaF₃薄膜具有张应力,而IBS LaF₃具有压应力,退火之后其压应力减小。热蒸发制备的MgF₂/LaF₃减反膜在193 nm透过率为99.4%,反射率为0.04%,离子束溅射制备的AlF₃/LaF₃减反膜透过率为99.2%,反射率为0.1%。     

Symbolic dynamics of jejunal motility in the irritable bowel

Different studies of the irritable bowel syndrome (IBS) by conventional analysis of jejunal motility report conflicting results. Therefore, our aim is to quantify the jejunal contraction activity by symbolic dynamics in order to discriminate between IBS and control subjects. Contraction amplitudes during fasting motility (phase II) are analyzed for 30 IBS and 30 healthy subjects. On the basis of a particular scale-independent discretization of the contraction amplitudes with respect to the median, IBS patients are characterized by increased block entropy as well as increased mean contraction amplitude. In a further more elementary level of analysis these differences can be reduced to specific contraction patterns within the time series, namely the fact that successive large contraction amplitudes are less ordered in IBS than in controls. These significant differences in jejunal motility may point to an altered control of the gut in IBS, although further studies on a representative number of patients have to be done for a validation of these findings. (c) 1999 American Institute of Physics.     

一维晶化束的辐射能损与束流冷却

 用Jacobian椭圆函数求解了一维晶化束的非线性动力学方程，并用第一类全椭圆积分表示了粒子振动周期。在经典物理学框架内，讨论了储存环中作相对论运动的带电粒子的辐射能损，以及由于辐射能损导致的束流冷却。结果表明, 由于辐射损失束流将进一步冷却。     

HIRFL-CSRm冷却束流寿命

实验研究了HIRFL-CSRm中电子冷却装置对C6+,Ar15+两种束流寿命的影响。首先,通过对比实验的测量确定电子冷却可以有效提高束流寿命;其次,探究了电子冷却装置中的各项参数（主要是电子束密度分布、流强、能量、绝热展开因子）是如何影响束流寿命的,通过改变电子束参数,测量束流寿命的变化趋势和规律,并且结合电子冷却相关理论对实验结果给予解释,最终通过实验优化和确定最佳的冷却装置参数,使束流在HIRFL-CSRm上获得了较高的寿命,从而提高HIRFL-CSRm束流累积过程中的流强增益。     

Far ultraviolet optical properties of MgF2 films deposited by ion-beam sputtering and their application as protective coatings for Al

Thin films of MgF₂ deposited by evaporation is a material widely used for its transparency in the far ultraviolet (FUV) down to ∼115 nm. In this paper the optical properties of ion-beam sputtered (IBS) MgF₂ in the FUV are investigated and compared with MgF₂ films deposited by evaporation. A slightly higher transparency at the 121.6-nm, H Lyman α line was obtained for IBS MgF₂ films compared to films deposited by evaporation, which makes IBS MgF₂ a promising protective material for Al reflective coatings. Experimental work on Al films that were protected with a thin evaporated MgF₂ film followed by an IBS MgF₂ film to produce a protective coating with optimum thickness showed a reflectance at 121.6 nm that was higher by about 3% compared to an Al film protected with an all-evaporated MgF₂ film.     

Laser-induced damage of the optical films prepared by electron beam evaporation and ion beam sputtering in vacuum

The laser-induced damage characteristics and adsorption effects of organic contamination molecules of two high reflectors (HR) prepared by electron beam evaporation (EB) and ion beam sputtering (IBS) method at 1064 nm is investigated in vacuum. It is found that EB films show the performance degradation of laser induced damages in vacuum while for IBS film, seems to have no this effect, in comparison with air environment. In addition, EB coatings also have the strong affinity with organic contamination molecules, in contrast of IBS films. The results reveal that ion beam sputtering (IBS) method seem to be one of the favorite film deposition techniques of the optical films used in vacuum and space environments.     

小型分置式斯特林制冷机理论冷量的计算方法

分置式斯特林制冷机由于连接管和室温腔等死容积的存在,其理论冷量的计算方法更是有别于整体式斯特林制冷机。文中着重以数值计算的思路计算了小型分置式斯特林制冷机的理论冷量,并通过实验测定。最后分析了主要工作参数诸如充气压力、工作频率等对分置式斯特林制冷机性能的影响。     

Prediction of Heat Conduction with Phase-change Effects during Cooling Stage of Injection Molding of High-density Polyethylene: Approximate Integral Approach

Phase-change problems, also known as the “Stefan problems” or “moving-boundary problems,” are practically significant in modern technological and engineering fields. Injection molding, one of the most widely used polymer processing techniques, can be divided into three stages: filling, packing, and cooling. The cooling stage, which accounts for over three fourths of total molding cycles, greatly affects both productivity and quality of the molded articles. In this work, an approximate integral method was adopted to predict the transient heat conduction with phase-change effects during the cooling stage of injection molding of crystalline polymers. Experiments were conducted to compare with the calculated results, and reasonable agreement was obtained. It was concluded that the present modeling makes good predictions for the cooling stage of injection molding of crystalline polymers, which may be applicable to further studies on the microstructure evolutions during injection molding process as well as the optimal designs in industrial applications.     

冷却速率对温敏聚N-异丙基丙烯酰胺胶体结晶过程的影响

冷却速率对结晶过程具有重要的影响. 本文采用温敏poly-N-isopropylacrylamide (PNIPAM) 胶体晶体体系实时观察了冷却速率对结晶晶粒尺寸的影响. 通过高倍透射明场观察和Bragg衍射观察研究连续冷却下的晶粒形核和生长实时演化过程, 发现随着冷却速率的增加, PNIPAM胶体晶体晶粒尺寸不断减少. 晶粒尺寸与冷却速率符合幂指数关系, 与金属体系具有相似的演化规律.