甲基丙烯酸甲酯-甲基丙烯酸无规共聚物的合成及其在乳液聚合中的应用

通过自由基共聚制备了不同组成的甲基丙烯酸甲酯-甲基丙烯酸无规共聚物,用碱中和后作为大分子乳化剂用于乳液聚合.研究了无规共聚物的组成、用量及反应温度对乳液聚合的影响.结果表明,在相同的反应条件下,乳化剂中聚甲基丙烯酸含量越多,乳液聚合速率越快;同一乳化剂,随乳化剂浓度的增加,乳液聚合速率增加;在乳化剂组成、浓度不变的情况下,反应温度越高,乳液聚合速率越大.     

高固含量乳液聚合中的表面活性技术研究进展

如何提高乳胶产品固含量及其性能一直是乳液制备工作所追求的重要目标。乳液聚合中可以使用各种乳化剂,也可不用乳化剂,但都必须使乳胶粒子表面具有亲水性即表面活性,因此,乳液聚合中的原理与技术实际上可以归结为使乳胶粒子表面具有亲水性即表面活性技术。各种研究表明,采用不同乳化剂和表面活性技术所制备的乳胶性能差别很大,合适有效的表面活性技术不仅大幅度提高聚合物乳液的性能,还可以缩短反应时间,简化制备工艺。本文详细评述了近几年来高固含量乳液聚合中常规乳化剂、可聚合乳化剂、复合乳化剂和表面活性单体及其与之相应的表面活性技术的研究现状,并对高固含量乳液乳化剂的发展进行了展望。     

水性环氧树脂乳液的研制

采用环氧树脂和非离子型表面活性剂反应合成了反应型水性环氧树脂乳化剂，将具有表面活性的分子链段引入到环氧树脂分子链中，用相反转技术制备水性环氧树脂乳液。研究了乳化剂合成时表面活性剂分子量、环氧树脂分子量，乳化剂构型、乳化剂浓度和乳化剂合成的反应时间对乳液稳定性的影响。     

反应性乳化剂在无皂硅溶胶苯丙乳液聚合中的应用

反应性乳化剂;硅溶胶;苯丙乳液;乳液聚合     

乳化剂对聚硅氧烷乳液稳定性的影响

研究了乳化剂烷基酚聚氧乙烯醚(OP)、烷基聚氧乙烯醚和烷基季铵盐对聚硅氧烷乳液聚合的影响。采用复合乳化剂可以提高乳液稳定性。结果表明：①在以D4、N-β-氨乙基-γ-氨丙基甲基二甲氧基硅烷为原料的乳液聚合中。当非离子型乳化剂烷基聚氧乙烯醚和离子型乳化剂烷基季铵盐复合使用时,二者性能互补,产生协同效应,可使聚合物乳液具有很大的稳定性。②在实验选定的乳化剂中,非离子型烷基聚氧乙烯醚乳化剂用量为80mL(含量为0．05g／mL)、离子型烷基季铵盐乳化剂为60mL(浓度为0．05g／mL)时。其乳液的电解质稳定性、pH稳定性、冻融高温稳定性和离心稳定性等较好。     

乳化沥青及其乳化剂的发展与应用

概述了国内外乳化沥青及其乳化剂在建筑防水、道路维修养护等领域的应用概况,着重论述了乳化剂的分类、选择方法以及乳化剂复配体系的应用情况。根据我国的现状,指出了乳化沥青的高性能化、沥青乳化剂多样化将是主要的发展方向。     

马来酸类可聚合乳化剂及其在乳液聚合中应用

使用可聚合乳化剂可以很好地解决传统乳化剂的缺点,提高乳液的应用性能.马来酸类乳化剂其可聚合基团反应活性适中,可以很好地键合在乳胶粒表面上,且更为突出的是这类乳化剂不易发生均聚,而是倾向于与单体发生共聚.研究表明,马来酸类可聚合乳化剂应用到乳液聚合中,可以改善乳胶液的性能,提高乳胶膜的耐水性等.文章介绍了这一类新型的乳化剂,并根据其亲水基团进行了分类,分别介绍其合成路线,总结了马来酸类乳化剂的特点,概述了在常见乳液聚合体系中的应用与研究.     

颗粒乳化剂的研究及应用

近年来,颗粒乳化剂因其在食品、采油、化妆品、医药、催化以及功能纳米材料制备等领域具有潜在应用前景而备受关注。本文综述了近来颗粒乳化剂的研究进展,归纳了颗粒乳化剂的种类,包括:无机纳米粒子、表面改性或杂化的无机粒子、有机纳米粒子以及特殊的颗粒乳化剂Janus粒子;并对颗粒乳化剂能够在油水界面稳定吸附的热力学机理和动力学行为进行了阐述,颗粒乳化剂在油水界面接触角以及粒径大小是其在界面稳定吸附的关键参数,而颗粒在油水界面的排布方式则主要受粒子之间相互作用的影响。重点介绍了颗粒乳化剂的热点应用,包括:(1)利用颗粒乳化剂制备Pickering乳液,以及通过对颗粒乳化剂的功能化,使得Pickering乳液具备环境响应性(即pH、盐浓度、温度、紫外光、磁场敏感响应性);(2)以颗粒乳化剂为构筑基元、以Pickering乳液为模板制备Janus颗粒、Colloidosome、具有多级结构的粒子或膜,以及多孔结构材料;(3) Janus粒子在催化领域的应用。     

稳态荧光探针法研究复配乳化剂的聚集行为

采用荧光探针技术,根据芘的第一振动峰I₁(373 nm)与第三振动峰I₃(384 nm)荧光强度的比值(I₁/I₃)随乳化剂浓度的变化,对十二烷基磺酸钠(AS)与壬基酚聚氧乙烯醚(Oπ-10)复配乳化剂的CMC值进行了测定,并与十二烷基磺酸钠(AS),壬基酚聚氧乙烯醚(Oπ-10)的CMC值进行了比较,结果表明复配乳化剂的CMC介于两者之间.以二苯甲酮为猝灭剂,用稳态荧光法测定了不同比例复配乳化剂的胶束聚集数,实验结果表明,复配乳化剂浓度为4—9倍CMC时,测定的胶束聚集数随复配乳化剂浓度的增大而线性增大;且Oπ-10:AS<2:1时,随着复合乳化剂中Oπ-10比例的增大,复配乳化剂胶束聚集数增大.利用芘的I₁/I₃值,结合胶束微环境的极性变化规律,探讨了复配乳化剂的聚集行为对硅丙乳液聚合物的影响.     

微乳液聚合

介绍了微乳化工艺和助乳化剂对单体液滴大小、乳化剂的吸附、乳液稳定性、聚合动力学和乳胶粒子大小及分布的影响,并讨论了单体亚微液滴成核机理。     

(2-甲基丙烯酰氧乙基)三甲基氯化铵-丙烯酰胺反相微乳液共聚合特性研究

选用SPAN80与OP10复合乳化剂、K₂S₂O₈-Na₂SO₃氧化还原引发剂,进行(2-甲基丙烯酰氧乙基)三甲基氯化铵-丙烯酰胺反相微乳液共聚合反应.研究了单体配比、电解质浓度和乳化体系的油水比对共聚物分子量及离子度的影响,考察了该共聚合体系的反应特性.     

Synthesis and Characterization of Hydrogel Nanoparticles Through Inverse Microemulsion Polymerization of 2-Acrylamido-2-methyl-1-propanesulfonic Acid

Nanosized hydrogel particles prepared through inverse microemulsion polymerization of 2-acrylamido-2-methyl-1-propanesulfonic acid, using the combination of an oil soluble emulsifier (SPAN80) with a water soluble emulsifier (TWEEN 80), and precise determination of HLB range related to the formation of stable single phase microemulsions.

The effect of crosslink density, water phase to oil phase ratio, and the hydrophilic-lipophilic balance (HLB) value on polymerization rate, particle size, and swelling ratio were investigated. It found that polymerization rate and particle size are strongly dependent on the water phase to oil phase ratio. Hydrogel samples prepared using oil soluble and water soluble initiators and the results showed that the initiator type had a great influence on monomer conversion and particle size. Effect of pH on equilibrium swelling of hydrogels was studied by dynamic light scattering and hydrogels showed pH-independent swelling behavior in a broad range of pH values. We also reported and discussed the crosslink density distribution in nanogels prepared by inverse microemulsion polymerization.     

水分散体系中丙烯酸四氟丙酯与苯乙烯的原子转移自由基共聚合

以2－溴代异丁酸乙酯（EBiB）为引发剂、CuBr/CuBr_2/1, 10-邻二氮菲（ phen）配合物为催化剂,在水分散体系中进行了丙烯酸四氟丙酯（TFPA）与苯乙烯 (St)的原子转移自由基共聚合,所得共聚物的分子量（M_n）随着单体总转化率的 增加而增大,分子量分布（M_w/M_n）较窄（1.26～1.65）,表现出“活性”聚合 的特征。用拓展的Kelen-Tudos法和Fineman-Ross法估算了共单体的表观竞聚率, 发现St的相对反应活性高于TFPA,因此当St和TFPA起始组成为1:1（摩尔比）时, 反应自发生成了含氟的准梯度或“渐变”共聚物。实验分别考察了三种乳化剂体系 ,即十二烷基磺酸钠（SLS）、全氟辛酸钠（SPFS）／SLS和全氟壬烯氧基苯磺酸钠 （OBS）／SLS对共聚合反应的影响,发现它们对共聚合的可控制性影响不大,且反 应过程中均无破乳现象发生;然而,以OBS/SLS复合乳化剂体系制备的共聚物乳液 的贮存稳定性明显优于以SLS或SPFS／SLS为乳化剂体系制备的共聚物乳液的稳定性 。     

Some aspects of anionic butadiene copolymerization

The relationship between ideal copolymerization behavior and the nature of reactive species in butyllithium (n-BuLi) initiated anionic copolymerization of styrene (St)- butadiene (Bd) in nonpolar solvent has been discussed. The monomer reactivity ratios (m.r.r.) for various reactive species were evaluated by kinetic study and statistical approach (using ¹³C NMR data) in St-Bd anionic copolymerization system with THF as polar additive. The Markovian mechanisms for different propagating reactions in this complex copolymerizing system have been postulated. Furthermore, “pseudo” zero order Markovian mechnism could be sophisticatedly established in the n-BuLi/tertiary amyloxy potassium (t-AmOK)/THF initiated St-Bd copolymerization system, provided that the apparent rate constants of both monomers are equal. Thus, by adjusting the ratio of K/Li and THF/Li, copolymers with composition almost identical to the ratio of initial monomer feed composition at different stages of conversion could be obtained.     

K2S2O8/Na2SO3引发St/BA微乳液共聚合的研究

以十二烷基硫酸钠／十二烷基苯磺酸钠(SDS／SDBS)为乳化剂，过硫酸钾／亚硫酸钠(K2S2O3／Ni2SO3)为引发剂进行苯乙烯／丙烯酸丁酯(SL／BA)微孔液共聚合反应。研究了引发剂浓度[I]OR、单体总浓度[M]、乳化剂含量[E]和聚合温度T对微孔液共聚合最大反应速率Rmax和共聚物粘均分子量^-Mη的影响，测定了共聚单体的竞聚率，结果得到：Rmax∝[I]^0.98OR[M]^0.81[E]^-0．34e^-4712／T，^-Mη∝[I]^-0.27OR[M]^0.48[E]^-0.68e^2304/T；rSt=0.598，rBA=0.0206。     

偏氟乙烯/六氟丙烯乳液共聚反应动力学

对气相含氟单体偏氟乙烯(VDF)/六氟丙烯(HFP)的乳液共聚反应动力学机理进行了研究.结果表明:在80℃下,上述两种单体共聚反应速率r对乳化剂浓度(S)、引发剂浓度(I)和反应总压力(p)分别呈0.05级、0.31级和1.59级反应,由此推导得乳液共聚的反应速率表达式为:r一1.11×10-4S0.05I0.31P1.59,其中速率常数k=1.11×10-4g-0.37L0.37(MPa)-0.59min-1.由上述动力学方程计算得到的乳液共聚反应速率与实验结果一致.同时对两种单体的竞聚率做了初步讨论.     

Effect of a bi-unsaturated monomer on the emulsion polymerization of ethyl acrylate

The emulsion polymerization and copolymerization of ethyl acrylate with a bi-unsaturated comonomer (divinylbenzene, 1,6-hexamethylene diacrylate), present in small proportions, in the presence of anionic emulsifier sodium dodecyl sulfate have been kinetically investigated at 60°C under batch conditions by gas chromatograhy and gravimetric methods. The rate of polymerization in interval 2 was found to be proportional to the 0,37, 0,23, and 0,5 power of the emulsifier concentration for the system A (ethyl acrylate), the system B (ethyl acrylatedivinylbenzene), and the system C (ethyl acrylate/1,6-hexamethylene diacrylate). Divinylbenzene was found to decrease both the rate of polymerization and the polymer particle size. Addition of 1,6-hexamethylene diacrylate slightly increases both the rate of polymerization and the polymer particle size.     

Mechanism of alternating copolymerization of methyl methacrylate with styrene in the presence of diethylaluminum chloride

A kinetic study of the propagation mechanism of the alternating copolymerization of styrene (St) with methyl methacrylate (MMA) in the presence of a complexing agent (diethylaluminum chloride, DEAC) in bulk and in tetrachloroethylene solutions at a molar ratio DEAC/MMA = 0.5 has been carried out. It has been shown that the copolymerization is a chain radical process characterized by a short active-center lifetime, bimolecular termination, and high rate of chain transfer to the complexed MMA. A kinetic scheme has been proposed for the propagation mechanism of alternating copolymerization in the presence of a complexing agent not requiring independent measurements of the equilibrium constant of complexation. It has been found that spontaneous and UV-initiated copolymerizations in the system have different mechanisms of initiation and a common mechanism of propagation. The propagation proceeds by addition of single monomers as well as donor-acceptor complexes of the comonomers to the propagation radicals, with the first mechanism being predominant. Inclusion of the monomers in the complex leads to an increase of the St reactivity and to a decrease of the MMA reactivity in propagation to the corresponding macroradicals in comparison with the reactivity of the free monomers. A number of kinetic and statistical parameters of the propagation reaction have been calculated.     

Radiation-induced emulsion copolymerization of tetrafluoroethylene with propylene. IV. Effects of emulsifier concentration and dose rate

Radiation-induced emulsion copolymerization of tetrafluoroethylene with propylene was carried out by batch operation with an initial molar ratio of tetrafluoroethylene to propylene of 3.0 in the emulsifier concentration range of 0.1 to 3.0% and in the dose rate range of 2 × 10⁴ to 2 × 10⁵ R/hr. The effects of emulsifier concentration and dose rate on the polymerization rate and the number-average degree of polymerization are discussed in comparison with the Smith-Ewart theory. The polymerization rate is proportional to the 0.26 power of emulsifier concentration and to the 0.7 power of dose rate. The degree of polymerization is independent of the emulsifier concentration and the dose rate above the critical micelle concentration (CMC) of the emulsifier. These results are not in agreement with the Smith-Ewart theory. It is explained that the termination reaction is a degradative chain transfer of propagating radicals to propylene. On the other hand, the copolymerization in emulsion occurs either below the CMC or in the absence of emulsifier. Under these conditions, however, it is impossible to obtain a copolymer of high molecular weight at a high rate of polymerization because of the presence of a small number of polymer particles formed and the short interval of chain growth in the polymer particle.     

以阳离子乳化剂进行丙烯酸丁酯－苯乙烯乳液共聚的动力学研究

采用十二烷基二甲基苄基氯化铵（１２２７）乳化剂，对丙烯酸丁酯（ＢＡ）－苯乙烯（Ｓｔ）进行乳液共聚，研究了影响聚合速度的各种因素，得出了聚合速率方程和表观活化能．